Skip to content

L
linux
Switch branch/tag
  1. 22 Jun, 2010 4 commits
    • K.Prasad's avatar
      powerpc, hw_breakpoint: Handle concurrent alignment interrupts · 2538c2d0
      K.Prasad authored 
      If an alignment interrupt occurs on an instruction that is being
single-stepped, the alignment interrupt handler currently handles
the single-step condition by unconditionally sending a SIGTRAP to
the process.  Other synchronous interrupts that result in the
instruction being emulated do likewise.

With hw_breakpoint support, the hw_breakpoint code needs to be able
to intercept these single-step events as well as those where the
instruction executes normally and a trace interrupt happens.

Fix this by making emulate_single_step() use the existing
single_step_exception() function instead of calling _exception()
directly.  We then make single_step_exception() use the abstracted
clear_single_step() rather than clearing bits in the MSR image
directly so that emulate_single_step() will continue to work
correctly on Book 3E processors.
Signed-off-by: default avatarK.Prasad <prasad@linux.vnet.ibm.com>
Signed-off-by: default avatarPaul Mackerras <paulus@samba.org>
      2538c2d0
    • K.Prasad's avatar
      powerpc, hw_breakpoints: Implement hw_breakpoints for 64-bit server processors · 5aae8a53
      K.Prasad authored 
      Implement perf-events based hw-breakpoint interfaces for PowerPC
64-bit server (Book III S) processors.  This allows access to a
given location to be used as an event that can be counted or
profiled by the perf_events subsystem.

This is done using the DABR (data breakpoint register), which can
also be used for process debugging via ptrace.  When perf_event
hw_breakpoint support is configured in, the perf_event subsystem
manages the DABR and arbitrates access to it, and ptrace then
creates a perf_event when it is requested to set a data breakpoint.

[Adopted suggestions from Paul Mackerras <paulus@samba.org> to
- emulate_step() all system-wide breakpoints and single-step only the
  per-task breakpoints
- perform arch-specific cleanup before unregistration through
  arch_unregister_hw_breakpoint()
]
Signed-off-by: default avatarK.Prasad <prasad@linux.vnet.ibm.com>
Signed-off-by: default avatarPaul Mackerras <paulus@samba.org>
      5aae8a53
    • K.Prasad's avatar
      hw_breakpoints: Allow arch-specific cleanup before breakpoint unregistration · f7136c51
      K.Prasad authored 
      Certain architectures (such as PowerPC) have a need to clean up data
structures before a breakpoint is unregistered.  This introduces an
arch-specific hook in release_bp_slot() along with a weak definition
in the form of a stub function.
Signed-off-by: default avatarK.Prasad <prasad@linux.vnet.ibm.com>
Acked-by: default avatarFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: default avatarPaul Mackerras <paulus@samba.org>
      f7136c51
    • Paul Mackerras's avatar
      powerpc: Emulate most Book I instructions in emulate_step() · 0016a4cf
      Paul Mackerras authored 
      This extends the emulate_step() function to handle a large proportion
of the Book I instructions implemented on current 64-bit server
processors.  The aim is to handle all the load and store instructions
used in the kernel, plus all of the instructions that appear between
l[wd]arx and st[wd]cx., so this handles the Altivec/VMX lvx and stvx
and the VSX lxv2dx and stxv2dx instructions (implemented in POWER7).

The new code can emulate user mode instructions, and checks the
effective address for a load or store if the saved state is for
user mode.  It doesn't handle little-endian mode at present.

For floating-point, Altivec/VMX and VSX instructions, it checks
that the saved MSR has the enable bit for the relevant facility
set, and if so, assumes that the FP/VMX/VSX registers contain
valid state, and does loads or stores directly to/from the
FP/VMX/VSX registers, using assembly helpers in ldstfp.S.

Instructions supported now include:
* Loads and stores, including some but not all VMX and VSX instructions,
  and lmw/stmw
* Atomic loads and stores (l[dw]arx, st[dw]cx.)
* Arithmetic instructions (add, subtract, multiply, divide, etc.)
* Compare instructions
* Rotate and mask instructions
* Shift instructions
* Logical instructions (and, or, xor, etc.)
* Condition register logical instructions
* mtcrf, cntlz[wd], exts[bhw]
* isync, sync, lwsync, ptesync, eieio
* Cache operations (dcbf, dcbst, dcbt, dcbtst)

The overflow-checking arithmetic instructions are not included, but
they appear not to be ever used in C code.

This uses decimal values for the minor opcodes in the switch statements
because that is what appears in the Power ISA specification, thus it is
easier to check that they are correct if they are in decimal.

If this is used to single-step an instruction where a data breakpoint
interrupt occurred, then there is the possibility that the instruction
is a lwarx or ldarx.  In that case we have to be careful not to lose the
reservation until we get to the matching st[wd]cx., or we'll never make
forward progress.  One alternative is to try to arrange that we can
return from interrupts and handle data breakpoint interrupts without
losing the reservation, which means not using any spinlocks, mutexes,
or atomic ops (including bitops).  That seems rather fragile.  The
other alternative is to emulate the larx/stcx and all the instructions
in between.  This is why this commit adds support for a wide range
of integer instructions.
Signed-off-by: default avatarPaul Mackerras <paulus@samba.org>
      0016a4cf
  3. 12 Jun, 2010 1 commit
  5. 11 Jun, 2010 34 commits
  7. 10 Jun, 2010 1 commit
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7