- 29 Aug, 2011 14 commits
-
-
Jayamohan Kallickal authored
This patch adds a shutdown routine. It fixes a bug where when be2net and be2iscsi are both used be2iscsi was not cleaning up its resources properly causing be2net to fail to get loaded when the system is rebooted. Signed-off-by:
Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Jayamohan Kallickal authored
Fix be2iscsi driver to use a separate pointer for each irq action->name field and avoid display corruption in /proc/interrupts. The be2iscsi driver was using a single static array in a function for the irq action->name field. This results in garbage output from /proc/interrupts The pointer for action->name is garbage and scribbles the output on the screen. This patch fixes the problem: 156: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PCI-MSI-X beiscsi_msix_0017 This patch is based on Prarit's patch here: http://www.spinics.net/lists/linux-scsi/msg52325.html but I have fixed up the failure paths and removed redundant check for !i suggested by Eike. Signed-off-by:
-
Chad Dupuis authored
Since active_mask is first assigned in an "else" block, the compiler throws a warning saying that the active_mask variable may be used uninitialized in a print statement later. Initialize active_mask to 0 in the declaration to stop the warning. Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
Giridhar Malavali authored
Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
-
Joe Carnuccio authored
Return sysfs error codes that match the conditions encountered. This prevents sysfs from retrying a request which is conditioned to fail under the current circumstance. Signed-off-by:
Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by:
-
Joe Carnuccio authored
Provide bsg interface for updating VPD attached on the I2C serial bus. Signed-off-by:
-
Joe Carnuccio authored
Corrects the return value for the cases where read/write edc fails; this prevents sysfs from retrying the operation until forever. Corrects the printk width specifier for the first byte of buf. Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
-
Chad Dupuis authored
[SCSI] qla2xxx: Enable write permission to some debug related module parameters to be changed dynamically. Signed-off-by:
-
Saurav Kashyap authored
Driver is not releasing the lock if ql2xdontresethba is set, this might lead to a lockup. Signed-off-by:
-
Saurav Kashyap authored
[jejb: fix up checkpatch.pl errors] Signed-off-by:
-
Giridhar Malavali authored
Minidump allows us to catpure a snapshot of the firmware/hardware states at the time of failure for further analysis. [jejb: added missing #include <linux/vmalloc.h> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> ] Signed-off-by:
-
- 27 Aug, 2011 26 commits
-
-
Swen Schillig authored
FICON Express8S supports hardware data router, which requires an adapted qdio request format. This part 2/2 exploits the functionality in zfcp. Signed-off-by:
Swen Schillig <swen@vnet.ibm.com> Signed-off-by:
Steffen Maier <maier@linux.vnet.ibm.com> Signed-off-by:
-
Swen Schillig authored
FICON Express8S supports hardware data router, which requires an adapted qdio request format. This part 1/2 provides the qdio base required for exploitation in zfcp. Signed-off-by:
-
Steffen Maier authored
DIF/DIX support for zfcp is no longer experimental, and config option is no longer necessary. Return error from queuecommand for unsupported data directions. Signed-off-by:
-
Jianyun Li authored
The Marvell Universal Message Interface (UMI) defines a messaging interface between host and Marvell products (Plato, for example). It considers situations of limited system resource and optimized system performance. UMI driver translates host request to message and sends message to FW via UMI, FW receives message and processes it, then sends response to UMI driver. FW generates an interrupt when it needs to send information or response to UMI driver Signed-off-by:
Jianyun Li <jyli@marvell.com> Signed-off-by:
-
Mike Christie authored
Export the name of iface session is attached to. This is needed so tools like iscsiadm/iscsistart can match the sessions to userspace ifaces when rebuilding iscsid's state during boot. Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by:
-
Vikas Chaudhary authored
Added new sysfs attr 'host_reset' in scsi_sysfs.c to perform adapter or firmware reset as suggested by Mike Christie here: http://marc.info/?l=linux-scsi&m=127359347111167&w=2 user/application can write "adapter" or "firmware" on this attr and it will call newly added function hook in scsi_host_template to call LDD adapter or firmware reset implementation. Signed-off-by:
-
Harish Zunjarrao authored
This command is used to read ACB params from firmware Signed-off-by:
Harish Zunjarrao <harish.zunjarrao@qlogic.com> Signed-off-by:
-
Harish Zunjarrao authored
This command will causes the firmware to update all configurations to pre-defined factory default settings. Signed-off-by:
-
TARUISI Hiroaki authored
Some CD-ROMs fail to report a media change correctly. The specific one for this patch simply fails to respond to commands, then gives a UNIT ATTENTION after being reset which returns ASC/ASCQ 28/00. This is out of spec behaviour, but add a check in the eat CC/UA on reset path to catch this case so the CD-ROM will function somewhat properly. [jejb: fixed up white space and accepted without signoff] Signed-off-by: -
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Added board_id, fw_state, phy_port_cnt, phy_port_num, iscsi_func_cnt, hba_model Signed-off-by:
-
Harish Zunjarrao authored
Signed-off-by:
-
Harish Zunjarrao authored
Signed-off-by:
-
Harish Zunjarrao authored
- Corrected return status - Added reset active check - Removed unused dma_map_sg calls - Added debug prints on failure Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Manish Rangankar authored
Hook qla4xxx in fw boot sysfs interface so iscsi tools can use the info to create boot sessions. Signed-off-by:
Manish Rangankar <manish.rangankar@qlogic.com> Signed-off-by:
-
Manish Rangankar authored
1. Remove device database entry (ddb) state. 2. Remove device database (DDB) list building. With open-iscsi integration the logins to the target devices are handled by the user space. So the information of target is now maintained in the iscsi_session object. This is handled at libiscsi level so there is no need to maintain a list of DDBs in the qla4xxx LLD. 3. qla4xxx: Remove add_device_dynamically. Since autologin in FW is disabled with open-iscsi integration, driver will never get an AEN for which driver has not requested a DDB index. So remove the add_device_dynamically function. 4. Remove qla4xxx_tgt_dscvr Since firmware autologin is disabled this function will not work. Now user has the ability to do the target discovery and login to each target individually. Firwmare will not do the login on its own. 5. Remove relogin related code All relogin is handled by userspace now. qla4xxx just need to notify userspace of a connection failure, this triggers the relogin. 6. Remove add_session and alloc_session Now qla4xxx uses iscsi_session_setup that would do the necessary allocations for session and ddb_entry. Signed-off-by:Lalit Chandivade <lalit.chandivade@qlogic.com> Signed-off-by:
-
Manish Rangankar authored
Add scsi_transport_iscsi hooks in qla4xxx to support iSCSI session management using iscsiadm. This patch is based on discussion here http://groups.google.com/group/open-iscsi/browse_thread/thread/e89fd888baf656a0# Now users can use iscsiadm to do target discovery and do login/logout to individual targets using the qla4xxx iSCSI class interface. This patch leaves some dead code, but to make it easier to review we are leaving and in the next patch we will remove that old code. V2 - NOTE: Added code to avoid waiting for AEN during login/logout in the driver, instead added a kernel to user event to notify iscsid about login status. Because of this iscsid will not get blocked. Signed-off-by:
-
Manish Rangankar authored
[SCSI] scsi_transport_iscsi: Add conn login, kernel to user, event to support offload session login. Offload drivers like qla4xxx will offload the sending of the login/logout pdus still, so this patch adds iscsi_conn_login_event which is used by these types of drivers to notify userspace that the connection has changed state. It also adds a iscsi_is_session_online helper so the lld can query the sessions state field. Signed-off-by:
-
Vikas Chaudhary authored
This patch adds bsg support to qla4xxx. Signed-off-by:
-
Mike Christie authored
This patch adds bsg support to the iscsi class. There is only 1 request, the host vendor one, supported. It is expected that this would be used for things like flash updates. This patch is made over this one http://marc.info/?l=linux-scsi&m=131149780020992&w=2Signed-off-by:
-
Vikas Chaudhary authored
Add support to set VLAN and show vlan settings in sysfs Signed-off-by:
-
Mike Christie authored
libiscsi does not support markers and if someone tries to set them the driver does a BUG(). There is not need to be that extreme. Just return -ENOSYS. Signed-off-by:
-
