The tmp108 does have an alert output that can be used as interrupt source
and can of course also be used as part of a thermal sensor setup for things
like thermal-based cpu frequencies, so document the necessary properties.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

According to the code right before the removed line, data->kind
should be either from DT or from id pointer. So there shouldn't
be an additional overwriting after the if-else statement.

So this patch just removes the overwriting line.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

If all three channels are disabled via in[123]_enable ABI,
the driver could suspend the chip for power saving purpose.

So this patch adds the PM runtime support in order to gain
more power control than system suspend and resume use case.

For PM runtime, there are a few related changes happening:
1) Added a new pm_dev device pointer for all the PM runtime
   callbacks. This is because hwmon core registers a child
   device for each hwmon driver and passes it back to each
   driver. So there might be a mismatch between two device
   pointers in the driver if mixing using them.
2) Added a check in ina3221_is_enabled() to make sure that
   the chip is resumed.
3) Bypassed the unchanged status in ina3221_write_enable()
   in order to keep the PM runtime refcount being matched.
4) Removed the reset routine in the probe() by calling the
   resume() via pm_runtime_get_sync() instead, as they're
   similar. It's also necessary to do so to match initial
   PM refcount with the number of enabled channels.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The data might need some time to get ready after channel enabling,
although the data register is always readable. The CVRF bit is to
indicate that data conversion is finished, so polling the CVRF bit
before data reading could ensure the result being valid.

An alternative way could be to wait for expected time between the
channel enabling and the data reading. And this could avoid extra
I2C communications. However, INA3221 seemly takes longer time than
what's stated in the datasheet. Test results show that sometimes
it couldn't finish data conversion in time.

So this patch plays safe by adding a CVRF polling to make sure the
data register is updated with the new data.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

This change adds a mutex to serialize accesses of sysfs attributes.

This is required when polling CVRF bit of the MASK/ENABLE register
because this bit is cleared on a read of this MASK/ENABLE register
or a write to CONFIG register, which means that this bit might be
accidentally cleared by reading other fields like alert flags.

So this patch adds a mutex lock to protect the write() and read()
callbacks. The read_string() callback won't need the lock since it
just returns the label without touching any hardware register.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

There is nothing critically wrong to read these two attributes
without having a is_enabled() check at this point. But reading
the MASK_ENABLE register would clear the CVRF bit according to
the datasheet. So it'd be safer to fence for disabled channels
in order to add pm runtime feature.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The OCC provides a variety of additional information about the state of
the host processor, such as throttling, error conditions, and the number
of OCCs detected in the system. This information is essential to service
processor applications such as fan control and host management.
Therefore, export this data in the form of sysfs attributes attached to
the platform device (to which the hwmon device is also attached).
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Setup the sensor attributes for every OCC sensor found by the first poll
response. Register the attributes with hwmon.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Add structures to define all sensor types and versions. Add sysfs show
and store functions for each sensor type. Add a method to construct the
"set user power cap" command and send it to the OCC. Add rate limit to
polling the OCC (in case user-space reads our hwmon entries rapidly).
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Add method to parse the response from the OCC poll command. This only
needs to be done during probe(), since the OCC shouldn't change the
number or format of sensors while it's running. The parsed response
allows quick access to sensor data, as well as information on the
number and version of sensors, which we need to instantiate hwmon
attributes.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

For the P8 OCC, add the procedure to send a command to the OCC over I2C
bus. This involves writing the OCC command registers with serial
communication operations (SCOMs) interpreted by the I2C slave. For the
P9 OCC, add a procedure to use the OCC in-kernel API to send a command
to the OCC through the SBE.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The OCC is a device embedded on a POWER processor that collects and
aggregates sensor data from the processor and system. The OCC can
provide the raw sensor data as well as perform thermal and power
management on the system.

This driver provides a hwmon interface to the OCC from a service
processor (e.g. a BMC). The driver supports both POWER8 and POWER9 OCCs.
Communications with the POWER8 OCC are established over standard I2C
bus. The driver communicates with the POWER9 OCC through the FSI-based
OCC driver, which handles the lower-level communication details.

This patch lays out the structure of the OCC hwmon driver. There are two
platform drivers, one each for P8 and P9 OCCs. These are probed through
the I2C tree and the FSI-based OCC driver, respectively. The patch also
defines the first common structures and methods between the two OCC
versions.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
[groeck: Fix up SPDX license identifier]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Document the bindings for I2C-based OCC hwmon device.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Document the hwmon interface for the OCC.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The OCC is a device embedded on a POWER processor that collects and
aggregates sensor data from the processor and system. The OCC can
provide the raw sensor data as well as perform thermal and power
management on the system.

This driver provides an atomic communications channel between a service
processor (e.g. a BMC) and the OCC. The driver is dependent on the FSI
SBEFIFO driver to get hardware access through the SBE to the OCC SRAM.
Commands are issued to the SBE to send or fetch data to the SRAM.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Document the bindings for the FSI-attached POWER9 On-Chip Controller.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

As per the usual standard with hwmon drivers the mapping to sysfs
entries follows the register map of the device e.g. in0_input
corresponds to the register 0x20, in1_input corresponds to 0x21 etc.

Hardware designers tend to work with input pins instead of registers
which is where things start to get confusing. A hardware designer might
say "the 1.5V rail is connected to the VCCP pin" leaving the software
designer none the wiser as to which of the sysfs entries should be
associated with the label "1.5V".

Try to bridge the gap by documenting the mapping of sysfs entries to
the corresponding pins. This should allow someone to create a
configuration file or other mapping without needing to dive into the
code and ADT datasheets.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

struct attribute::name which this local variable name is eventually
assigned to is "const char*", and so is the template parameter. We might
as well preserve the constness all the way through.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The ADM series of hotswap controllers support extending
the current measurement range by using a sensing resistor
value other than the typical 1 mOhm. For example, using a 0.5 mOhm
sensing resistor doubles the maximal current can be measured.

Current driver assumes a shunt resistor value of 1 mOhm in calculation,
meaning for other resistor values, hwmon will report scaled
current/power measurements. This patch parses device tree parameter
"shunt-resistor-micro-ohms", if there is one.
Signed-off-by: Kun Yi <kunyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

adm127x are hot-swap controllers that allow a circuit board to be removed from
or inserted into a live backplane. This patch adds the device tree
bindings documentation.
Signed-off-by: Kun Yi <kunyi@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Pull ARM SoC fixes from Olof Johansson:
 "Volume is a little higher than usual due to a set of gpio fixes for
  Davinci platforms that's been around a while, still seemed appropriate
  to not hold off until next merge window.

  Besides that it's the usual mix of minor fixes, mostly corrections of
  small stuff in device trees.

  Major stability-related one is the removal of a regulator from DT on
  Rock960, since DVFS caused undervoltage. I expect it'll be restored
  once they figure out the underlying issue"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
  MAINTAINERS: Remove unused Qualcomm SoC mailing list
  ARM: davinci: dm644x: set the GPIO base to 0
  ARM: davinci: da830: set the GPIO base to 0
  ARM: davinci: dm355: set the GPIO base to 0
  ARM: davinci: dm646x: set the GPIO base to 0
  ARM: davinci: dm365: set the GPIO base to 0
  ARM: davinci: da850: set the GPIO base to 0
  gpio: davinci: restore a way to manually specify the GPIO base
  ARM: davinci: dm644x: define gpio interrupts as separate resources
  ARM: davinci: dm355: define gpio interrupts as separate resources
  ARM: davinci: dm646x: define gpio interrupts as separate resources
  ARM: davinci: dm365: define gpio interrupts as separate resources
  ARM: davinci: da8xx: define gpio interrupts as separate resources
  ARM: dts: at91: sama5d2: use the divided clock for SMC
  ARM: dts: imx51-zii-rdu1: Remove EEPROM node
  ARM: dts: rockchip: Remove @0 from the veyron memory node
  arm64: dts: rockchip: Fix PCIe reset polarity for rk3399-puma-haikou.
  arm64: dts: qcom: msm8998: Reserve gpio ranges on MTP
  arm64: dts: sdm845-mtp: Reserve reserved gpios
  arm64: dts: ti: k3-am654: Fix wakeup_uart reg address
  ...

Pull xen fixes from Juergen Gross:

 - A revert of a previous commit as it is no longer necessary and has
   shown to cause problems in some memory hotplug cases.

 - Some small fixes and a minor cleanup.

 - A patch for adding better diagnostic data in a very rare failure
   case.

* tag 'for-linus-4.20a-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  pvcalls-front: fixes incorrect error handling
  Revert "xen/balloon: Mark unallocated host memory as UNUSABLE"
  xen: xlate_mmu: add missing header to fix 'W=1' warning
  xen/x86: add diagnostic printout to xen_mc_flush() in case of error
  x86/xen: cleanup includes in arch/x86/xen/spinlock.c

Pull dmaengine fixes from Vinod Koul:
 "This contains two fixes to at_hdmac which fixes long standing bus
  reported recently on serial transfers causing memory leak. These fixes
  were done by Richard Genoud"

* tag 'dmaengine-fix-4.20-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: at_hdmac: fix module unloading
  dmaengine: at_hdmac: fix memory leak in at_dma_xlate()

Pull STIBP fallout fixes from Thomas Gleixner:
 "The performance destruction department finally got it's act together
  and came up with a cure for the STIPB regression:

   - Provide a command line option to control the spectre v2 user space
     mitigations. Default is either seccomp or prctl (if seccomp is
     disabled in Kconfig). prctl allows mitigation opt-in, seccomp
     enables the migitation for sandboxed processes.

   - Rework the code to handle the conditional STIBP/IBPB control and
     remove the now unused ptrace_may_access_sched() optimization
     attempt

   - Disable STIBP automatically when SMT is disabled

   - Optimize the switch_to() logic to avoid MSR writes and invocations
     of __switch_to_xtra().

   - Make the asynchronous speculation TIF updates synchronous to
     prevent stale mitigation state.

  As a general cleanup this also makes retpoline directly depend on
  compiler support and removes the 'minimal retpoline' option which just
  pretended to provide some form of security while providing none"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
  x86/speculation: Provide IBPB always command line options
  x86/speculation: Add seccomp Spectre v2 user space protection mode
  x86/speculation: Enable prctl mode for spectre_v2_user
  x86/speculation: Add prctl() control for indirect branch speculation
  x86/speculation: Prepare arch_smt_update() for PRCTL mode
  x86/speculation: Prevent stale SPEC_CTRL msr content
  x86/speculation: Split out TIF update
  ptrace: Remove unused ptrace_may_access_sched() and MODE_IBRS
  x86/speculation: Prepare for conditional IBPB in switch_mm()
  x86/speculation: Avoid __switch_to_xtra() calls
  x86/process: Consolidate and simplify switch_to_xtra() code
  x86/speculation: Prepare for per task indirect branch speculation control
  x86/speculation: Add command line control for indirect branch speculation
  x86/speculation: Unify conditional spectre v2 print functions
  x86/speculataion: Mark command line parser data __initdata
  x86/speculation: Mark string arrays const correctly
  x86/speculation: Reorder the spec_v2 code
  x86/l1tf: Show actual SMT state
  x86/speculation: Rework SMT state change
  sched/smt: Expose sched_smt_present static key
  ...

Pull block layer fixes from Jens Axboe:

 - Single range elevator discard merge fix, that caused crashes (Ming)

 - Fix for a regression in O_DIRECT, where we could potentially lose the
   error value (Maximilian Heyne)

 - NVMe pull request from Christoph, with little fixes all over the map
   for NVMe.

* tag 'for-linus-20181201' of git://git.kernel.dk/linux-block:
  block: fix single range discard merge
  nvme-rdma: fix double freeing of async event data
  nvme: flush namespace scanning work just before removing namespaces
  nvme: warn when finding multi-port subsystems without multipathing enabled
  fs: fix lost error code in dio_complete
  nvme-pci: fix surprise removal
  nvme-fc: initialize nvme_req(rq)->ctrl after calling __nvme_fc_init_request()
  nvme: Free ctrl device name on init failure

Pull PCI fixes from Bjorn Helgaas:

 - Fix a link speed checking interface that broke PCIe gen3 cards in
   gen1 slots (Mikulas Patocka)

 - Fix an imx6 link training error (Trent Piepho)

 - Fix a layerscape outbound window accessor calling error (Hou
   Zhiqiang)

 - Fix a DesignWare endpoint MSI-X address calculation error (Gustavo
   Pimentel)

* tag 'pci-v4.20-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Fix incorrect value returned from pcie_get_speed_cap()
  PCI: dwc: Fix MSI-X EP framework address calculation bug
  PCI: layerscape: Fix wrong invocation of outbound window disable accessor
  PCI: imx6: Fix link training status detection in link up check

  - Fix DesignWare endpoint MSI-X address calculation bug (Gustavo
    Pimentel)

  - Fix Layerscape outbound window disable usage (Hou Zhiqiang)

  - Fix imx6 link up detection (Trent Piepho)

* lorenzo/pci/controller-fixes:
  PCI: dwc: Fix MSI-X EP framework address calculation bug
  PCI: layerscape: Fix wrong invocation of outbound window disable accessor
  PCI: imx6: Fix link training status detection in link up check

The macros PCI_EXP_LNKCAP_SLS_*GB are values, not bit masks.  We must mask
the register and compare it against them.

This fixes errors like this:

  amdgpu: [powerplay] failed to send message 261 ret is 0

when a PCIe-v3 card is plugged into a PCIe-v1 slot, because the slot is
being incorrectly reported as PCIe-v3 capable.

6cf57be0, which appeared in v4.17, added pcie_get_speed_cap() with the
incorrect test of PCI_EXP_LNKCAP_SLS as a bitmask.  5d9a6330, which
appeared in v4.19, changed amdgpu to use pcie_get_speed_cap(), so the
amdgpu bug reports below are regressions in v4.19.

Fixes: 6cf57be0 ("PCI: Add pcie_get_speed_cap() to find max supported link speed")
Fixes: 5d9a6330 ("drm/amdgpu: use pcie functions for link width and speed")
Link: https://bugs.freedesktop.org/show_bug.cgi?id=108704
Link: https://bugs.freedesktop.org/show_bug.cgi?id=108778Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
[bhelgaas: update comment, remove use of PCI_EXP_LNKCAP_SLS_8_0GB and
PCI_EXP_LNKCAP_SLS_16_0GB since those should be covered by PCI_EXP_LNKCAP2,
remove test of PCI_EXP_LNKCAP for zero, since that register is required]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org	# v4.17+

Merge misc fixes from Andrew Morton:
 "31 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (31 commits)
  ocfs2: fix potential use after free
  mm/khugepaged: fix the xas_create_range() error path
  mm/khugepaged: collapse_shmem() do not crash on Compound
  mm/khugepaged: collapse_shmem() without freezing new_page
  mm/khugepaged: minor reorderings in collapse_shmem()
  mm/khugepaged: collapse_shmem() remember to clear holes
  mm/khugepaged: fix crashes due to misaccounted holes
  mm/khugepaged: collapse_shmem() stop if punched or truncated
  mm/huge_memory: fix lockdep complaint on 32-bit i_size_read()
  mm/huge_memory: splitting set mapping+index before unfreeze
  mm/huge_memory: rename freeze_page() to unmap_page()
  initramfs: clean old path before creating a hardlink
  kernel/kcov.c: mark funcs in __sanitizer_cov_trace_pc() as notrace
  psi: make disabling/enabling easier for vendor kernels
  proc: fixup map_files test on arm
  debugobjects: avoid recursive calls with kmemleak
  userfaultfd: shmem: UFFDIO_COPY: set the page dirty if VM_WRITE is not set
  userfaultfd: shmem: add i_size checks
  userfaultfd: shmem/hugetlbfs: only allow to register VM_MAYWRITE vmas
  userfaultfd: shmem: allocate anonymous memory for MAP_PRIVATE shmem
  ...

Pull few more MIPS fixes from Paul Burton:

 - Fix mips_get_syscall_arg() to operate on the task specified when
   detecting o32 tasks running on MIPS64 kernels.

 - Fix some incorrect GPIO pin muxing for the MT7620 SoC.

 - Update the linux-mips mailing list address.

* tag 'mips_fixes_4.20_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MAINTAINERS: Update linux-mips mailing list address
  MIPS: ralink: Fix mt7620 nd_sd pinmux
  mips: fix mips_get_syscall_arg o32 check

Pull arm64 fixes from Catalin Marinas:

 - Cortex-A76 erratum workaround

 - ftrace fix to enable syscall events on arm64

 - Fix uninitialised pointer in iort_get_platform_device_domain()

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  ACPI/IORT: Fix iort_get_platform_device_domain() uninitialized pointer value
  arm64: ftrace: Fix to enable syscall events on arm64
  arm64: Add workaround for Cortex-A76 erratum 1286807

Pull stackleak plugin fix from Kees Cook:
 "Fix crash by not allowing kprobing of stackleak_erase() (Alexander
  Popov)"

* tag 'gcc-plugins-v4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  stackleak: Disable function tracing and kprobes for stackleak_erase()

Merge tag 'fscache-fixes-20181130' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

Pull fscache and cachefiles fixes from David Howells:
 "Misc fixes:

   - Fix an assertion failure at fs/cachefiles/xattr.c:138 caused by a
     race between a cache object lookup failing and someone attempting
     to reenable that object, thereby triggering an update of the
     object's attributes.

   - Fix an assertion failure at fs/fscache/operation.c:449 caused by a
     split atomic subtract and atomic read that allows a race to happen.

   - Fix a leak of backing pages when simultaneously reading the same
     page from the same object from two or more threads.

   - Fix a hang due to a race between a cache object being discarded and
     the corresponding cookie being reenabled.

  There are also some minor cleanups:

   - Cast an enum value to a different enum type to prevent clang from
     generating a warning. This shouldn't cause any sort of change in
     the emitted code.

   - Use ktime_get_real_seconds() instead of get_seconds(). This is just
     used to uniquify a filename for an object to be placed in the
     graveyard. Objects placed there are deleted by cachfilesd in
     userspace immediately thereafter.

   - Remove an initialised, but otherwise unused variable. This should
     have been entirely optimised away anyway"

* tag 'fscache-fixes-20181130' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  fscache, cachefiles: remove redundant variable 'cache'
  cachefiles: avoid deprecated get_seconds()
  cachefiles: Explicitly cast enumerated type in put_object
  fscache: fix race between enablement and dropping of object
  cachefiles: Fix page leak in cachefiles_read_backing_file while vmscan is active
  fscache: Fix race in fscache_op_complete() due to split atomic_sub & read
  cachefiles: Fix an assertion failure when trying to update a failed object

The linux-mips.org infrastructure has been unreliable recently & nobody
with sufficient access to fix it is around to do so. As a result we're
moving away from it, and part of this is migrating our mailing list to
kernel.org.

Replace all instances of linux-mips@linux-mips.org in MAINTAINERS with
the shiny new linux-mips@vger.kernel.org address.

The new list is now being archived on kernel.org at
https://lore.kernel.org/linux-mips/ which also holds the history of the
old linux-mips.org list.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-mips@linux-mips.org

ocfs2_get_dentry() calls iput(inode) to drop the reference count of
inode, and if the reference count hits 0, inode is freed.  However, in
this function, it then reads inode->i_generation, which may result in a
use after free bug.  Move the put operation later.

Link: http://lkml.kernel.org/r/1543109237-110227-1-git-send-email-bianpan2016@163.com
Fixes: 781f200c("ocfs2: Remove masklog ML_EXPORT.")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Changwei Ge <ge.changwei@h3c.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

collapse_shmem()'s xas_nomem() is very unlikely to fail, but it is
rightly given a failure path, so move the whole xas_create_range() block
up before __SetPageLocked(new_page): so that it does not need to
remember to unlock_page(new_page).

Add the missing mem_cgroup_cancel_charge(), and set (currently unused)
result to SCAN_FAIL rather than SCAN_SUCCEED.

Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1811261531200.2275@eggly.anvils
Fixes: 77da9389 ("mm: Convert collapse_shmem to XArray")
Signed-off-by: Hugh Dickins <hughd@kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

collapse_shmem()'s VM_BUG_ON_PAGE(PageTransCompound) was unsafe: before
it holds page lock of the first page, racing truncation then extension
might conceivably have inserted a hugepage there already.  Fail with the
SCAN_PAGE_COMPOUND result, instead of crashing (CONFIG_DEBUG_VM=y) or
otherwise mishandling the unexpected hugepage - though later we might
code up a more constructive way of handling it, with SCAN_SUCCESS.

Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1811261529310.2275@eggly.anvils
Fixes: f3f0e1d2 ("khugepaged: add support of collapse for tmpfs/shmem pages")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>	[4.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

khugepaged's collapse_shmem() does almost all of its work, to assemble
the huge new_page from 512 scattered old pages, with the new_page's
refcount frozen to 0 (and refcounts of all old pages so far also frozen
to 0).  Including shmem_getpage() to read in any which were out on swap,
memory reclaim if necessary to allocate their intermediate pages, and
copying over all the data from old to new.

Imagine the frozen refcount as a spinlock held, but without any lock
debugging to highlight the abuse: it's not good, and under serious load
heads into lockups - speculative getters of the page are not expecting
to spin while khugepaged is rescheduled.

One can get a little further under load by hacking around elsewhere; but
fortunately, freezing the new_page turns out to have been entirely
unnecessary, with no hacks needed elsewhere.

The huge new_page lock is already held throughout, and guards all its
subpages as they are brought one by one into the page cache tree; and
anything reading the data in that page, without the lock, before it has
been marked PageUptodate, would already be in the wrong.  So simply
eliminate the freezing of the new_page.

Each of the old pages remains frozen with refcount 0 after it has been
replaced by a new_page subpage in the page cache tree, until they are
all unfrozen on success or failure: just as before.  They could be
unfrozen sooner, but cause no problem once no longer visible to
find_get_entry(), filemap_map_pages() and other speculative lookups.

Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1811261527570.2275@eggly.anvils
Fixes: f3f0e1d2 ("khugepaged: add support of collapse for tmpfs/shmem pages")
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>	[4.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Several cleanups in collapse_shmem(): most of which probably do not
really matter, beyond doing things in a more familiar and reassuring
order.  Simplify the failure gotos in the main loop, and on success
update stats while interrupts still disabled from the last iteration.

Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1811261526400.2275@eggly.anvils
Fixes: f3f0e1d2 ("khugepaged: add support of collapse for tmpfs/shmem pages")
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>	[4.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>