- 19 Feb, 2012 28 commits
-
-
Akinobu Mita authored
Use find_first_zero_bit to find the first cleared bit in a memory region. This also includes the following minor changes. - Use bitmap_zero - Reduce unnecessary atomic bitops usage Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Acked-by:
Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Douglas Gilbert authored
The SCSI GET LBA STATUS command was introduced in SBC-3 revision 20 in September 2009. At that time the Parameter Data Length field in the response had an associated byte offset of 8. Then in SBC-3 revision 25 (October 2010) that byte offset was changed to 4. The sg_get_lba_status utility in sg3_utils version 1.33 (released earlier today) has been changed to calculate the newer response length. However the implementation of GET LBA STATUS command in the scsi_debug driver still uses the original byte offset. modify the Parameter Data Length field value in the GET LBA STATUS command response to comply with the change in SBC-3 revision 25 Signed-off-by: -
Scott Teel authored
Certain types of changes to devices should not be interpreted as a device change that would cause the device to be removed and re-added. These include RAID level and Firmware revision changes. However, these attribute changes DO need to be reflected in the controller info structure's dev structure list, so that sysfs and /proc info files for the devices will reflect the new values. Signed-off-by:
Scott Teel <scott.stacy.teel@hp.com> Acked-by:
-
Scott Teel authored
Reduce confusion and inaccuracy caused by dated naming of vars and functions referring to external target devices. CURRENT NAMING: PROPOSED NAMING: "MSA2xxx devices" "external target devices" msa2xxx_model ext_target_model is_msa2xxx is_ext_target add_msa2xxx_enclosure add_ext_target_dev nmsa2xxx_enclosures n_ext_target_devs Signed-off-by:
Scott Teel <scott.teel@hp.com> Signed-off-by:
-
Scott Teel authored
Driver limits SAS external target IDs to range 1-8. Need to increase limit and clean up overlapping concepts of targets and paths in the code. There are several defined constants that control this: HPSA_MAX_TARGETS_PER_CTLR 16 MAX_MSA2XXX_ENCLOSURES 32 HPSA_MAX_PATHS 8 We can condense this to one constant: MAX_EXT_TARGETS 32 SAS switches allow for 8 connections, and there is capacity for 4 switches per enclosure in largest blade enclosure type. Signed-off-by:
-
Stephen M. Cameron authored
It should call hpsa_set_bus_target_lun rather than individually setting bus, target and lun. Signed-off-by:
-
Stephen M. Cameron authored
Some distros have a "rescan-scsi-bus.sh" script which depends on SCSI REPORT LUNs not reporting something different than what the driver tells the kernel, even if the driver uses scan_start and scan_finished methods of the SCSI host template to override the usual SCSI midlayer discovery code. Previously, 1 was added to the LUN to make room to insert the RAID controller device at LUN 0. Now, the RAID controller is moved to bus 3, and 1 is no longer added to the LUN. However, SCSI REPORT LUNS on Smart Array doesn't report physical devices like tape drives or auto-loaders as it turns out, so those particular device types still won't match. Generally the logical drives are reported first however, so at least those should match. Signed-off-by:
-
Stephen M. Cameron authored
Upgraded firmware on Smart Array P7xx (and some others) made them show up as SCSI revision 5 devices and this caused the driver to fail to map MSA2xxx logical drives to the correct bus/target/lun. A symptom of this would be that the target ID of the logical drives as presented by the external storage array is ignored, and all such logical drives are assigned to target zero, differentiated only by LUN. Some multipath software reportedly does not deal well with this behavior, failing to recognize different paths to the same device as such. Signed-off-by:
-
Stephen M. Cameron authored
Sometimes, for testing purposes (e.g. testing rmmod on a system that normally boots using hpsa) it's nice to rename the driver and split it into two drivers and restrict it to certain controllers. This makes that easier. Signed-off-by:
-
Stephen M. Cameron authored
hpsa_register_scsi just calls hpsa_scsi_detect. Move the guts of hpsa_scsi_detect into hpsa_register_scsi and get rid of hpsa_scsi_detect. Signed-off-by:
-
Stephen M. Cameron authored
[SCSI] hpsa: removed unneeded structure member max_sg_entries and fix badly named constant MAXSGENTRIES We had both h->max_sg_entries and h->maxsgentries in the per controller structure which is terribly confusing. max_sg_entries was really just a constant, 32, which defines how big the "block fetch table" is, which is as large as the max number of SG elements embedded within a command (excluding SG elements in chain blocks). MAXSGENTRIES was the constant used to denote the max number of SG elements embedded within a command, also a poor name. So renamed MAXSGENTREIS to SG_ENTRIES_IN_CMD, and removed h->max_sg_entries and replaced it with SG_ENTRIES_IN_CMD. h->maxsgentries is unchanged, and is the maximum number of sg elements the controller will support in a command, including those in chain blocks, minus 1 for the chain block pointer.. Signed-off-by:
-
Stephen M. Cameron authored
Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Vikas Chaudhary authored
sysfs patch to view port_state: /sys/class/iscsi_host/host*/port_state sysfs patch to view port_speed: /sys/class/iscsi_host/host*/port_speed Signed-off-by: -
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
sysfs patch to view target alias: /sys/class/iscsi_session/session*/targetalias Signed-off-by:
-
James Smart authored
Signed-off-by:
Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
-
James Smart authored
Note: this is a replacement patch for the issue pointed out in http://www.gossamer-threads.com/lists/linux/kernel/1477270Signed-off-by:
-
James Smart authored
Locking fix and Memory leak Fixes - Fix Locking code raises IRQ twice (NA) - Fix mailbox and vpi memory leaks (126818) Signed-off-by:
-
James Smart authored
FC Discovery state machine fixes. - Fix bug with driver returning the inactive ndlp (125743) - Fix discovery problem when in pt2pt by copying old ndlp state before state change (126887) - Fix ndlp nodelist not empty wait timeout during driver unloading (127052) Signed-off-by:
-
James Smart authored
T10 Diff fixes and enhancements: - Add SLI4 Lancer support for T10 DIF / BlockGuard (121980) - Fix SLI4 BlockGuard behavior when protection data is generated by HBA (121980) - Enhance debugfs for injecting T10 DIF errors (123966, 132966) - Fix Incorrect usage of bghm for BlockGuard errors (127022) Signed-off-by:
-
James Smart authored
SLI related fixes: - Fix REG_RPI fails on SLI4 HBA putting NPort into NPR state (126230) - Fix ELS FDISC failing with local reject / invalid RPI. (126350) - Fix reset port when reset is needed during fw_dump (125807) - Fix unbounded firmware revision string from port cause panic (126560) - Fix driver behavior when receiving an ADISC (126654) - Fix driver not returning when bad ndlp found in abts error event handling (126209) - Add more driver logs in area of SLI4 port error attention and reset recovery (126813, 124466) - Fix failure in handling large CQ/EQ identifiers in an IOV environment (126856) - Fix for driver using duplicate RPIs after lancer port reset (126723) - Clear vport->fc_myDID in lpfc_els_issue_fdisc to guarentee a zero SID (126779, 126897) - Fix for SLI4 Port delivery for BLS ABORT ACC (126289) Signed-off-by:
-
James Smart authored
BSG and User interface fixes: - Fix driver processing an els command using 16Gb FC Adapter (126345) - Change SLI4 FC port internal loopback to inner internal (126409) - Fix bug with driver dump command type 4 using 16Gb FC Adapter (126406) - Create character device to take a reference on the driver (126082) Signed-off-by:
-
Mark Salyzyn authored
IO_XFER_ERROR_BREAK and IO_XFER_OPEN_RETRY_TIMEOUT are deficient of the required actions as outlined in the programming manual for the pm8001. Due to the overlapping code requirements of these recovery responses, we found it necessary to bundle them together into one patch. When a break is received during the command phase (ssp_completion), this is a result of a timeout or interruption on the bus. Logic suggests that we should retry the command. When a break is received during the data-phase (ssp_event), the task must be aborted on the target or it will retain a data-phase lock turning the target reticent to all future media commands yet will successfully respond to TUR, INQUIRY and ABORT leading eventually to target failure through several abort-cycle loops. The open retry interval is exceedingly short resulting in occasional target drop-off during expander resets or when targets push-back during bad-block remapping. Increased effective timeout from 130ms to 1.5 seconds for each try so as to trigger after the administrative inquiry/tur timeout in the scsi subsystem to keep error-recovery harmonics to a minimum. When an open retry timeout event is received, the action required by the targets is to issue an abort for the outstanding command then logic suggests we retry the command as this state is usually an indication of a credit block or busy condition on the target. We hijacked the pm8001_handle_event work queue handler so that it will handle task as an argument instead of device for the workers in support of the deferred handling outlined above. Moderate to Heavy bad-path testing on a 2.6.32 vintage kernel, compile-testing on scsi-misc-2.6 kernel ... Signed-off-by:
Mark Salyzyn <mark_salyzyn@xyratex.com> Acked-by:
Jack Wang <jack_wang@usish.com> Signed-off-by:
-
Mark Salyzyn authored
Jack noticed I dropped a patch fragment associated with a flags automatic variable in mpi_set_phys_g3_with_ssc (ooops) and that the pre-emptive locking that piggy-backed this patch was not in-fact necessary because of underlying atomic accesses to the hardware. Here is the updated patch fixing these two issues. The pm8001 driver is missing the FUNC_GET_EVENTS handler in the phy control function. Since the pm8001_bar4_shift function was not designed to be called at runtime, added locking surrounding the adjustment for all accesses. Signed-off-by:
-
Mark Salyzyn authored
pm8001_phy_control PHY_FUNC_HARD_RESET locks up on second try via smp_phy_control because response HW_EVENT_PHY_START_STATUS fails to complete previous command. The PM8001F_RUN_TIME flag is not treated as a bit, but a state in all readers, yet once we are operational or in the run time state, the flags use a bit-set operation. Signed-off-by:
-
Oliver Neukum authored
This implements basic power management for SCSI tapes. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Acked-by:
Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by:
-
- 18 Feb, 2012 12 commits
-
-
Alan Stern authored
This patch (as1520) fixes a bug in the SCSI layer's power management implementation. LUN scanning can be carried out asynchronously in do_scan_async(), and sd uses an asynchronous thread for the time-consuming parts of disk probing in sd_probe_async(). Currently nothing coordinates these async threads with system sleep transitions; they can and do attempt to continue scanning/probing SCSI devices even after the host adapter has been suspended. As one might expect, the outcome is not ideal. This is what the "prepare" stage of system suspend was created for. After the prepare callback has been called for a host, target, or device, drivers are not allowed to register any children underneath them. Currently the SCSI prepare callback is not implemented; this patch rectifies that omission. For SCSI hosts, the prepare routine calls scsi_complete_async_scans() to wait until async scanning is finished. It might be slightly more efficient to wait only until the host in question has been scanned, but there's currently no way to do that. Besides, during a sleep transition we will ultimately have to wait until all the host scanning has finished anyway. For SCSI devices, the prepare routine calls async_synchronize_full() to wait until sd probing is finished. The routine does nothing for SCSI targets, because asynchronous target scanning is done only as part of host scanning. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> CC: <stable@kernel.org> Signed-off-by:
-
Huajun Li authored
In do_scan_async(), calling scsi_autopm_put_host(shost) may reference freed shost, and cause Posison overwitten warning. Yes, this case can happen, for example, an USB is disconnected just when do_scan_async() thread starts to run, then scsi_host_put() called in scsi_finish_async_scan() will lead to shost be freed(because the refcount of shost->shost_gendev decreases to 1 after USB disconnects), at this point, if references shost again, system will show following warning msg. To make scsi_autopm_put_host(shost) always reference a valid shost, put it just before scsi_host_put() in function scsi_finish_async_scan(). [ 299.281565] ============================================================================= [ 299.281634] BUG kmalloc-4096 (Tainted: G I ): Poison overwritten [ 299.281682] ----------------------------------------------------------------------------- [ 299.281684] [ 299.281752] INFO: 0xffff880056c305d0-0xffff880056c305d0. First byte 0x6a instead of 0x6b [ 299.281816] INFO: Allocated in scsi_host_alloc+0x4a/0x490 age=1688 cpu=1 pid=2004 [ 299.281870] __slab_alloc+0x617/0x6c1 [ 299.281901] __kmalloc+0x28c/0x2e0 [ 299.281931] scsi_host_alloc+0x4a/0x490 [ 299.281966] usb_stor_probe1+0x5b/0xc40 [usb_storage] [ 299.282010] storage_probe+0xa4/0xe0 [usb_storage] [ 299.282062] usb_probe_interface+0x172/0x330 [usbcore] [ 299.282105] driver_probe_device+0x257/0x3b0 [ 299.282138] __driver_attach+0x103/0x110 [ 299.282171] bus_for_each_dev+0x8e/0xe0 [ 299.282201] driver_attach+0x26/0x30 [ 299.282230] bus_add_driver+0x1c4/0x430 [ 299.282260] driver_register+0xb6/0x230 [ 299.282298] usb_register_driver+0xe5/0x270 [usbcore] [ 299.282337] 0xffffffffa04ab03d [ 299.282364] do_one_initcall+0x47/0x230 [ 299.282396] sys_init_module+0xa0f/0x1fe0 [ 299.282429] INFO: Freed in scsi_host_dev_release+0x18a/0x1d0 age=85 cpu=0 pid=2008 [ 299.282482] __slab_free+0x3c/0x2a1 [ 299.282510] kfree+0x296/0x310 [ 299.282536] scsi_host_dev_release+0x18a/0x1d0 [ 299.282574] device_release+0x74/0x100 [ 299.282606] kobject_release+0xc7/0x2a0 [ 299.282637] kobject_put+0x54/0xa0 [ 299.282668] put_device+0x27/0x40 [ 299.282694] scsi_host_put+0x1d/0x30 [ 299.282723] do_scan_async+0x1fc/0x2b0 [ 299.282753] kthread+0xdf/0xf0 [ 299.282782] kernel_thread_helper+0x4/0x10 [ 299.282817] INFO: Slab 0xffffea00015b0c00 objects=7 used=7 fp=0x (null) flags=0x100000000004080 [ 299.282882] INFO: Object 0xffff880056c30000 @offset=0 fp=0x (null) [ 299.282884] ... Signed-off-by:Huajun Li <huajun.li.lee@gmail.com> Cc: stable@kernel.org Acked-by:
-
Chad Dupuis authored
Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
Giridhar Malavali authored
Signed-off-by:
-
Shyam Sundar authored
With IOs running and PegHalt testing the system reboots when memory reset is performed during device initialization. Signed-off-by:
Shyam Sundar <shyam.sundar@qlogic.com> Signed-off-by:
-
Giridhar Malavali authored
[SCSI] qla2xxx: Complete mailbox command timedout to avoid initialization failures during next reset cycle. Complete the mailbox command timed out before initiating another abort cycle to recover so that mailbox commands issued during next reset cycle don't fail due to pending mailbox access timeout. Signed-off-by:
-
Michael Christie authored
Remove the check for a NULL fcport so that the host reset will run unconditionally to unwedge any commands before the device is offlined and to prevent a quick runthrough of the SCSI error handling. Signed-off-by:
Michael Christie <mchristi@redhat.com> Signed-off-by:
-
Andrew Vasquez authored
ISP2200 adapters only have 24 mailbox registers so read only that many. Reported-by:
Olatunji Ruwase <oor@cs.cmu.edu> Signed-off-by:
Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by:
-
Andrew Vasquez authored
This can cause instability in mailbox command state machine handling. Signed-off-by:
-
Andrew Vasquez authored
Not clearing the options flags in mbx1 could lead the firmware into interpreting old data in mbx1 through mbx8. This could lead to inadvertent DMA read/write operations to stale memory. Signed-off-by:
-
Andrew Vasquez authored
Many locations within the driver would use an inconsistent set of checks to determine ISP-reset state. Consolidate the checks into this inline-helper. Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
