- 01 Jul, 2013 40 commits
-
-
Ben Widawsky authored
This helps when we have per VM buffer capturing. Signed-off-by:
Ben Widawsky <ben@bwidawsk.net> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Ben Widawsky authored
Not only was there an extra, but since we now kzalloc the error state, we don't need either. Signed-off-by:
-
Ville Syrjälä authored
The DPLL lock bit, and the DPIO phy status bits are read-only and controlled by the hardware, so they will never be set by the driver. Mask them out when reading the hw state, so that the state comparison won't fail. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
Jesse Barnes <jbarnes@virtuosugeek.org> [danvet: Jesse asked for a code comment and I wholeheartly agree, so added one.] Signed-off-by:
-
Daniel Vetter authored
i9xx doesn't use pre_enable at all, so we can fold this in now. Reviewed-by:
Imre Deak <imre.deak@intel.com> Signed-off-by:
-
Daniel Vetter authored
Now that we have the proper pipe config to track this, we don't need to write any registers any more. Note that for platforms without DPLL_MD (pre-gen4) which store the pixel mutliplier in the DPLL register I've decided to keep the seemingly "redundant" write: The comment right below saying "do this trice for luck" doesn't instill confidence ... v2: Drop a few now unnecessary local variables and switch the enable function to take a struct intel_crtc * to simply arguments. v3: Rebase on top of the newly-colored BUG_ON. v4: Amend commit message to alliviate Imre's comment about the redudant DPLL write for the pixel mutliplier. Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Reviewed-by:
-
Daniel Vetter authored
In addition to existing stuff we also need to track DPLL_MD on gen4 and vlv. This is prep work so that we can move the dpll enable sequence out from the ->mode_set callback into the crtc enabling functions. Reviewed-by:
-
Daniel Vetter authored
The ->pre_enable hook is only used for the cpu edp port on ilk-ivb, so we can safely move it up across the fdi pll enabling. Unfortunately we can't (yet) merge in the pre_pll enable hook despite that only lvds uses it on ilk-ivb: Since the same lvds hook is also need on i9xx platforms we need to fix up the pll enabling sequence there, too. Reviewed-by:
-
Daniel Vetter authored
Lots of bangin my head against the wall^UExperiments have shown that we really need to enable the lvds port before we enable plls. Strangely that seems to include the fdi rx pll on the pch. Note that the pch pll assert can fire since the lvds port has it's own special clock source settings in the DPLL register, which means it will never have a shared dpll (since there's only one LVDS port). Anyway, encode this new evidence with a few nice WARNs. v2: Incorporate review comments from Imre. - Explain why lvds can't have a shared dpll. - Update the WARN output. Cc: Imre Deak <imre.deak@intel.com> Reviewed-by:
-
Daniel Vetter authored
Mostly since I _really_ don't want to touch the vlv hell. No code change, just duplication. Also kill a now seriously outdated code comment - the remark about the dvo encoder is now handled with the pipe A quirk. v2: Update the BUG_ONs as suggested by Jani (both in vlv_ and i9xx_ functions, since the split happens here). Cc: Jani Nikula <jani.nikula@linux.intel.com> Reviewed-by:
-
Daniel Vetter authored
Just yet another prep step to be able to do all this up-front, before we've set up any of the shared dplls in the new state. This will eventually be useful for atomic modesetting. Reviewed-by:
Damien Lespiau <damien.lespiau@intel.com> Signed-off-by:
-
Daniel Vetter authored
It's been splattered over 3 different places all doing random things. Now we have (mostly) the same sequence as i8xx/i9xx, but all called from the crtc_enable hook (through the pll->enable function): - write new dividers - enable vco and wait for stable clocks - write again for the pixel mutliplier I've left the seemingly random 200 usec delay in there, just in case. Also move the encoder->pre_pll_enable hook into the crtc_enable function, at the same spot we currently have a hack to enable the lvds port. Since that hack is now redundant, kill it. While doing this patch I've learned the hard way that we can only fire up the LVDS port if both the pch dpll _and_ the fdi rc pll are not yet enabled. Otherwise things go haywire, at least on cpt. v2: It is paramount to write the FPx divisors before we enable the the vco by writing to the DPLL registers, for otherwise the divisors won't get updated. This is in line with the i8xx/i9xx dpll. v3: To keep the nice abstraction add a ->mode_set callback to set the divisors. Also streamline the enabling/disabling code a bit by removing some cargo-cult duplication and clearing registers where possible in the ->disable hook. v4: Remove now unused local variable. Acked-by:
-
Damien Lespiau authored
Once we've found the the context object programmed in CCID, there's no need to look the other objects in the list. Signed-off-by:
-
Damien Lespiau authored
A genuine 'static' omission and 2 other warnings triggered by not including the header where those functions where defined. Signed-off-by:
-
Damien Lespiau authored
Missing spaces and misplaced '*'. Signed-off-by:
-
Damien Lespiau authored
Caught with checkpatch.pl. Suggested-by:
-
Damien Lespiau authored
When running on my snb machine, recent kernels display successively: [drm:intel_update_fbc], fbc set to per-chip default [drm:intel_update_fbc], fbc disabled per module param But no module param is set. This happens because the check for the module parameter uses a variable that has been overridden inside the "per-chip default" code. Fix up the logic and add another reason for the FBC to the be disabled. Signed-off-by:
-
Damien Lespiau authored
This function has no user outside of intel_pm.c. Signed-off-by:
-
Paulo Zanoni authored
We currently print a DRM_DEBUG_KMS message on the happy path and don't print anything on the "failed to allocate" path. On some desktop environments (e.g., Unity) I see the "scheduling delayed FBC enable" thousands and thousands of times on my dmesg. So kill the useless message for the happy case, saving a lot of dmesg space, and properly signal the "kzalloc fail" case. Signed-off-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by:
Zoltan Nyul <zoltan.nyul@intel.com> Signed-off-by:
-
Chris Wilson authored
So it appears that I have encountered some bogosity when trying to call i915_error_printf() with many arguments from print_error_buffers(). The symptom is that the vsnprintf parser tries to interpret an integer arg as a character string, the resulting OOPS indicating stack corruption. Replacing the single call with its 13 format specifiers and arguments with multiple calls to i915_error_printf() worked fine. This patch goes one step further and introduced i915_error_puts() to pass the strings simply. It may not fix the root cause, but it does prevent my box from dying and I think helps make print_error_buffers() more friendly. Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66077 Cc: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by:
-
Chris Wilson authored
Harmonise the completion logic between the non-blocking and normal wait_rendering paths, and move that logic into a common function. In the process, we note that the last_write_seqno is by definition the earlier of the two read/write seqnos and so all successful waits will have passed the last_write_seqno. Therefore we can unconditionally clear the write seqno and its domains in the completion logic. v2: Add the missing ring parameter, because sometimes it is good to have things compile. Signed-off-by:
-
Chris Wilson authored
In the introduction of the non-blocking wait, I cut'n'pasted the wait completion code from normal locked path. Unfortunately, this neglected that the normal path returned early if the wait returned early. The result is that read-only waits may return whilst the GPU is still writing to the bo. Fixes regression from commit 3236f57a [v3.7] Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Fri Aug 24 09:35:09 2012 +0100 drm/i915: Use a non-blocking wait for set-to-domain ioctl Signed-off-by:
-
Xiong Zhang authored
On DevCPT, the control register for Transcoder DP Sync Polarity is TRANS_DP_CTL, not DP_CTL. Without this patch, Many call trace occur on CPT machine with DP monitor. The call trace is like: *ERROR* mismatch in adjusted_mode.flags(expected X,found X) v2: use intel-crtc to simple patch, suggested by Daniel. Signed-off-by:
Xiong Zhang <xiong.y.zhang@intel.com> [danvet: Extend the encoder->get_config comment to specify that we now also depend upon intel_encoder->base.crtc being correct. Also bikeshed s/intel_crtc/crtc/.] Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65287Signed-off-by:
-
Daniel Vetter authored
Our interrupt handler (in hardirq context) could race with the timer (in softirq context), hence we need to hold the spinlock around the call to ->hdp_irq_setup in intel_hpd_irq_handler, too. But as an optimization (and more so to clarify things) we don't need to do the irqsave/restore dance in the hardirq context. Note also that on ilk+ the race isn't just against the hotplug reenable timer, but also against the fifo underrun reporting. That one also modifies the SDEIMR register (again protected by the same dev_priv->irq_lock). To lock things down again sprinkle a assert_spin_locked. But exclude the functions touching SDEIMR for now, I want to extract them all into a new helper function (like we do already for pipestate, display interrupts and all the various gt interrupts). v2: Add the missing 't' Egbert spotted in a comment. v3: Actually fix the right misspelled comment (Paulo). Cc: Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
The usual pattern for our sub-function irq_handlers is that they check for the no-irq case themselves. This results in more streamlined code in the upper irq handlers. v2: Rebase on top of the i965g/gm sdvo hpd fix. Cc: Egbert Eich <eich@suse.de> Reviewed-by:
Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
Everywhere the same. Note that this patch leaves unnecessary braces behind, but the next patch will kill those all anyway (including the if itself) so I've figured I can keep the diff a bit smaller. v2: Rebase on top of the i965g/gm sdvo hpd fix. Cc: Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
We already have a vfunc for this (and other parts of the hpd storm handling code already use it). v2: Rebase on top of the i965g/gm sdvo hpd fix. Cc: Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
The combination of Paulo's fifo underrun detection code and Egbert's hpd storm handling code unfortunately made the hpd storm handling code racy. To avoid duplicating tricky interrupt locking code over all platforms start with a bit of refactoring. This patch is the very first step since in the end the irq storm handling code will handle all hotplug logic (and so also encapsulate the locking nicely). v2: Rebase on top of the i965g/gm sdvo hpd fix. Cc: Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
By the time we write DEIER in the postinstall hook the interrupt handler could run any time. And it does modify DEIER to handle interrupts. Hence the DEIER read-modify-write cycle for enabling the PCU event source is racy. Close this races the same way we handle vblank interrupts: Unconditionally enable the interrupt in the IER register, but conditionally mask it in IMR. The later poses no such race since the interrupt handler does not touch DEIMR. Also update the comment, the clearing has already happened unconditionally above. v2: Actually shove the updated comment into the right train^W commit, as spotted by Paulo. Cc: Paulo Zanoni <przanoni@gmail.com> Reviewed-by:
-
Daniel Vetter authored
The haswell unclaimed register handling code forgot to take the spinlock. Since this is in the context of the non-rentrant interupt handler and we only have one interrupt handler it is sufficient to just grab the spinlock - we do not need to exclude any other interrupts from running on the same cpu. To prevent such gaffles in the future sprinkle assert_spin_locked over these functions. Unfornately this requires us to hold the spinlock in the ironlake postinstall hook where it is not strictly required: Currently that is run in single-threaded context and with userspace exlcuded from running concurrent ioctls. Add a comment explaining this. v2: ivb_can_enable_err_int also needs to be protected by the spinlock. To ensure this won't happen in the future again also sprinkle a spinlock assert in there. v3: Kill the 2nd call to ivb_can_enable_err_int I've accidentally left behind, spotted by Paulo. Cc: Paulo Zanoni <przanoni@gmail.com> Reviewed-by:
Paulo Zanoni <przanoni@gmail.com> Signed-off-by:
-
Ben Widawsky authored
With updates to the spec, we can actually see the context layout, and how many dwords are allocated. That table suggests we need 70720 bytes per HW context. Rounded up, this is 18 pages. Looking at what lives after the current 4 pages we use, I can't see too much important (mostly it's d3d related), but there are a couple of things which look scary. I am hopeful this can explain some of our odd HSW failures. v2: Make the context only 17 pages. The power context space isn't used ever, and execlists aren't used in our driver, making the actual total 66944 bytes. v3: Add a comment to the code. (Jesse & Paulo) Reported-by:
"Azad, Vinit" <vinit.azad@intel.com> Cc: stable@vger.kernel.org Reviewed-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
-
Ville Syrjälä authored
We forgot to add VLV_DISPLAY_BASE to the VLV sprite registers, which caused the sprites to not work at all. Signed-off-by:
-
Ville Syrjälä authored
The PIPECONF color range bit doesn't appear to be effective, on HDMI outputs at least. The color range bit in the port register works though, so let's use it. I have not yet verified whether the PIPECONF bit works on DP outputs. This reverts commit 83a2af88. Signed-off-by:
-
Ville Syrjälä authored
LPF is short for "low pass filter". Signed-off-by:
-
Ville Syrjälä authored
The current PLL settings produce a rather unstable picture when I hook up a VLV to my HP ZR24w display via a VGA cable. According to VLV2A0_DP_eDP_HDMI_DPIO_driver_vbios_notes_9, we should use the the same LPF coefficients for DAC as we do for HDMI and RBR DP. And indeed that seems to cure the shivers. v2: Add the name of the relevant document to the commit message Signed-off-by:
-
Ville Syrjälä authored
If the current GPU frquency is below RPe, and we're asked to increase it, just go directly to RPe. This should provide better performance faster than letting the frequency trickle up in response to the up threshold interrupts. For now just do it for VLV, since that matches quite closely how VLV used to operate when the rps delayed timer kept things at RPe always. Signed-off-by:
-
Ville Syrjälä authored
There's little point in increasing the GPU frequency from the delayed rps work on VLV. Now when the GPU is idle, the GPU frequency actually keeps dropping gradually until it hits the minimum, whereas previously it just ping-ponged constantly between RPe and RPe-1. Signed-off-by:
-
Ville Syrjälä authored
I can't find GEN6_RP_INTERRUPT_LIMITS (0xA014) anywhere in VLV docs. Reading it always returns zero from what I can tell, and eliminating it doesn't seem to make any difference to the behaviour of the system. Signed-off-by:
-
Ville Syrjälä authored
Eliminate the weird inverted logic from the rps new_delay comparison. Signed-off-by:
-
Ville Syrjälä authored
It seems that even though Punit reports the frequency change to have been completed, it still reports the old frequency in the status register for some time. So rather than polling for Punit to complete the frequency change after each request, poll before. This gets rid of the spurious "Punit overrode GPU freq" messages. This also lets us continue working while Punit is performing the actual frequency change. As a result, openarena demo088-test1 timedemo average fps is increased by ~5 fps, and the slowest frame duration is reduced by ~25%. The sysfs cur_freq file always reads the current frequency from Punit anyway, so having rps.cur_delay be slightly off at times doesn't matter. Signed-off-by:
-
Ville Syrjälä authored
Always print both the MHz value and raw register value for rps stuff. Also kill a somewhat pointless local 'rpe' variable and just use dev_priv->rps.rpe_delay. While at it clean up the caps in "GPU" and "Punit" debug messages. Signed-off-by:
-
