Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Also renames a few things to make volumes and switches match up in
alsamixer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

The version isn't being updated or used, the kernel revision
tracking is enough.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Change the legacy default register configuration, which left some
internal components on.
Now we have either DAPM, or other ways to control these bits,
so there is no need to enable them by default.

The affected parts:
Disable ADCL and ADCR
Disable ARXL2 and ARXR2 analog PGA (playback)
Disable APLL by default
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

fsi_master_xxx function should be protected by spin lock,
because it are used from both FSI-A and FSI-B.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The WM8978 codec from Wolfson Microelectronics is very similar to
wm8974, but is stereo and also has some differences in pin configuration
and internal signal routing. This driver is based on wm8974 and takes
the differences into account.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The board supports both GPIO sets for the AC97 bus and the analogue
outputs can be switched between this and the WM8580 so add some
comments saying what the setup the standard kernel expects is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Since, we have generic AC97 controller driver and all the machines
have moved to that, there is no need for old s3c2443-ac97.c to exist.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Switch to use s3c-ac97.c AC97 controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Switch to use s3c-ac97.c AC97 controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds the common machine driver for SMDKs that
have a WM9713 codec attched to the AC97 controller.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add the AC97 controller driver for Samsung SoCs that have one.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Barry Song <Barry.Song@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Barry Song <Barry.Song@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Sometimes after a suspend-resume cycle, the ALSA application
restarts the stream when resume fails and McASP fails to work
as the clock is not enabled. This patch corrects this bug.

Testes on TI DA850/OMAP-L138 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

tests show frequent suspend/resume(frequent poweroff/on ad1836 internal
components) maybe make ad1836 clock mode wrong sometimes after wakeup.
This patch reset/restore ad1836 clock mode while executing PM, then
ad1836 can always resume to right clock status.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Several SuperH platforms, including sh7722, sh7343, sh7354, sh7367 include
a Sound Interface Unit (SIU). This patch adds DAI and platform / DMA
drivers for this interface.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Several shortcuts for popular uses of some of SOC_ENUM_* and
SOC_VALUE_ENUM_* macros.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Many macros from include/sound/soc-dapm.h take an array and a number of
elements in it as arguments, whereas most users use static arrays and use
"x, ARRAY_SIZE(x)" as arguments. This patch adds simplified versions of
those macros, calling ARRAY_SIZE() internally.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.oc.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Remember to free the temporary register-cache.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf: x86: Add support for the ANY bit
  perf: Change the is_software_event() definition
  perf: Honour event state for aux stream data
  perf: Fix perf_event_do_pending() fallback callsite
  perf kmem: Print usage help for unknown commands
  perf kmem: Increase "Hit" column length
  hw-breakpoints, perf: Fix broken mmiotrace due to dr6 by reference change
  perf timechart: Use tid not pid for COMM change

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: Reassign prev and switch_count when reacquire_kernel_lock() fail
  sched: Fix vmark regression on big machines

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: retry FS IOs even if it has failed with AC_ERR_INVALID

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  tty: fix race in tty_fasync
  serial: serial_cs: oxsemi quirk breaks resume
  serial: imx: bit &/| confusion
  serial: Fix crash if the minimum rate of the device is > 9600 baud
  serial-core: resume serial hardware with no_console_suspend
  serial: 8250_pnp: use wildcard for serial Wacom tablets
  nozomi: quick fix for the close/close bug
  compat_ioctl: Supress "unknown cmd" message on serial /dev/console

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: hv: fix smp problems in the hyperv core code
  Staging: et131x: Fix 2.6.33rc1 regression in et131x
  Staging: asus_oled: fix oops in 2.6.32.2

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  Revert "sysdev: fix prototype for memory_sysdev_class show/store functions"
  driver-core: fix devtmpfs crash on s390

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: isp1362: fix build failure on ARM systems via irq_flags cleanup
  USB: isp1362: better 64bit printf warning fixes
  USB: fix usbstorage for 2770:915d delivers no FAT
  USB: Fix level of isp1760 Reloading ptd error message
  USB: FHCI: avoid NULL pointer dereference
  USB: Fix duplicate sysfs problem after device reset.
  USB: add speed values for USB 3.0 and wireless controllers
  USB: add missing delay during remote wakeup
  USB: EHCI & UHCI: fix race between root-hub suspend and port resume
  USB: EHCI: fix handling of unusual interrupt intervals
  USB: Don't use GFP_KERNEL while we cannot reset a storage device
  USB: fix bitmask merge error
  usb: serial: fix memory leak in generic driver
  USB: serial: fix USB serial fix kfifo_len locking

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  fs/bio.c: fix shadows sparse warning
  drbd: The kernel code is now equivalent to out of tree release 8.3.7
  drbd: Allow online resizing of DRBD devices while peer not reachable (needs to be explicitly forced)
  drbd: Don't go into StandAlone mode when authentification failes because of network error
  drivers/block/drbd/drbd_receiver.c: correct NULL test
  cfq-iosched: Respect ioprio_class when preempting
  genhd: overlapping variable definition
  block: removed unused as_io_context
  DM: Fix device mapper topology stacking
  block: bdev_stack_limits wrapper
  block: Fix discard alignment calculation and printing
  block: Correct handling of bottom device misaligment
  drbd: check on CONFIG_LBDAF, not LBD
  drivers/block/drbd: Correct NULL test
  drbd: Silenced an assert that could triggered after changing write ordering method
  drbd: Kconfig fix
  drbd: Fix for a race between IO and a detach operation [Bugz 262]
  drbd: Use drbd_crypto_is_hash() instead of an open coded check

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits)
  ACPI: delete acpi_processor_power_verify_c2()
  ACPI: allow C3 > 1000usec
  ACPI: enable C2 and Turbo-mode on Nehalem notebooks on A/C
  ACPI: power_meter: remove double kfree()
  ACPI: processor: restrict early _PDC to opt-in platforms
  ACPI: Fix unused variable warning in sbs.c
  acpi: make ACPI device id constant
  sony-laptop - fix using of uninitialized variable
  ACPI: Fix section mismatch error for acpi_early_processor_set_pdc()
  eeepc-laptop: disable wireless hotplug for 1201N
  eeepc-laptop: add hotplug_disable parameter
  eeepc-laptop: switch to using sparse keymap library
  eeepc-laptop: dmi blacklist to disable pci hotplug code
  eeepc-laptop: disable cpu speed control on EeePC 701
  ACPI: don't cond_resched if irq is disabled
  ACPI: Remove unnecessary cast.
  ACPI: Advertise to BIOS in _OSC: _OST on _PPC changes
  ACPI: EC: Add wait for irq storm
  ACPI: SBS: Move SBS HC callback to faster Notify queue
  x86, ACPI: delete acpi_boot_table_init() return value
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
  ecryptfs: use after free
  ecryptfs: Eliminate useless code
  ecryptfs: fix interpose/interpolate typos in comments
  ecryptfs: pass matching flags to interpose as defined and used there
  ecryptfs: remove unnecessary d_drop calls in ecryptfs_link
  ecryptfs: don't ignore return value from lock_rename
  ecryptfs: initialize private persistent file before dereferencing pointer
  eCryptfs: Remove mmap from directory operations
  eCryptfs: Add getattr function
  eCryptfs: Use notify_change for truncating lower inodes

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: fix possible panic on unmount
  Btrfs: deal with NULL acl sent to btrfs_set_acl
  Btrfs: fix regression in orphan cleanup
  Btrfs: Fix race in btrfs_mark_extent_written
  Btrfs, fix memory leaks in error paths
  Btrfs: align offsets for btrfs_ordered_update_i_size
  btrfs: fix missing last-entry in readdir(3)

In free_unmap_area_noflush(), va->flags is marked as VM_LAZY_FREE first, and
then vmap_lazy_nr is increased atomically.

But, in __purge_vmap_area_lazy(), while traversing of vmap_are_list, nr
is counted by checking VM_LAZY_FREE is set to va->flags.  After counting
the variable nr, kernel reads vmap_lazy_nr atomically and checks a
BUG_ON condition whether nr is greater than vmap_lazy_nr to prevent
vmap_lazy_nr from being negative.

The problem is that, if interrupted right after marking VM_LAZY_FREE,
increment of vmap_lazy_nr can be delayed.  Consequently, BUG_ON
condition can be met because nr is counted more than vmap_lazy_nr.

It is highly probable when vmalloc/vfree are called frequently.  This
scenario have been verified by adding delay between marking VM_LAZY_FREE
and increasing vmap_lazy_nr in free_unmap_area_noflush().

Even the vmap_lazy_nr is for checking high watermark, it never be the
strict watermark.  Although the BUG_ON condition is to prevent
vmap_lazy_nr from being negative, vmap_lazy_nr is signed variable.  So,
it could go down to negative value temporarily.

Consequently, removing the BUG_ON condition is proper.

A possible BUG_ON message is like the below.

   kernel BUG at mm/vmalloc.c:517!
   invalid opcode: 0000 [#1] SMP
   EIP: 0060:[<c04824a4>] EFLAGS: 00010297 CPU: 3
   EIP is at __purge_vmap_area_lazy+0x144/0x150
   EAX: ee8a8818 EBX: c08e77d4 ECX: e7c7ae40 EDX: c08e77ec
   ESI: 000081fe EDI: e7c7ae60 EBP: e7c7ae64 ESP: e7c7ae3c
   DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
   Call Trace:
   [<c0482ad9>] free_unmap_vmap_area_noflush+0x69/0x70
   [<c0482b02>] remove_vm_area+0x22/0x70
   [<c0482c15>] __vunmap+0x45/0xe0
   [<c04831ec>] vmalloc+0x2c/0x30
   Code: 8d 59 e0 eb 04 66 90 89 cb 89 d0 e8 87 fe ff ff 8b 43 20 89 da 8d 48 e0 8d 43 20 3b 04 24 75 e7 fe 05 a8 a5 a3 c0 e9 78 ff ff ff <0f> 0b eb fe 90 8d b4 26 00 00 00 00 56 89 c6 b8 ac a5 a3 c0 31
   EIP: [<c04824a4>] __purge_vmap_area_lazy+0x144/0x150 SS:ESP 0068:e7c7ae3c

[ See also http://marc.info/?l=linux-kernel&m=126335856228090&w=2 ]
Signed-off-by: Yongseok Koh <yongseok.koh@samsung.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh64: wire up sys_accept4.
  sh: unwire sys_recvmmsg.
  sh: ms7724: Correct sh-eth EEPROM polling timeout.

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 5888/1: arm: Update comments in cacheflush.h and remove unnecessary V6 and V7 comments
  ARM: 5886/1: arm: Fix cpu_proc_fin() for proc-v7.S and make kexec work
  ARM: 5885/1: arm: Flush TLB entries in setup_mm_for_reboot()
  ARM: 5884/1: arm: Fix DCC console for v7
  ARM: 5883/1: Revert "disable NX support for OABI-supporting kernels"
  ARM: 5882/1: ARM: Fix uncompress code compile for different defines of flush(void)
  ARM: fix badly placed mach/plat entries in Kconfig & Makefile

Propagate the ANY bit into the fixed counter config for v3 and higher.
Signed-off-by: Stephane Eranian <eranian@google.com>
[a.p.zijlstra@chello.nl: split from larger patch]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4b5430c6.0f975e0a.1bf9.ffff85fe@mx.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

The is_software_event() definition always confuses me because its an
exclusive expression, make it an inclusive one.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Anton reported that perf record kept receiving events even after calling
ioctl(PERF_EVENT_IOC_DISABLE). It turns out that FORK,COMM and MMAP
events didn't respect the disabled state and kept flowing in.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Anton Blanchard <anton@samba.org>
LKML-Reference: <1263459187.4244.265.camel@laptop>
CC: stable@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Paul questioned the context in which we should call
perf_event_do_pending(). After looking at that I found that it should be
called from IRQ context these days, however the fallback call-site is
placed in softirq context. Ammend this by placing the callback in the IRQ
timer path.
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1263374859.4244.192.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>