Pull late GPIO fixes from Linus Walleij:
 "Here are the (hopefully) last GPIO fixes for v4.0.  Nothing
  controversial whatsoever, just fixes:

   - syscon GPIO fix for Keystone DSP GPIOs

   - pin number translation fix for ACPI GPIO

   - a smallish compiler warning fix on the mpc8xxx driver"

* tag 'gpio-v4.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: syscon: reduce message level when direction reg offset not in dt
  gpiolib: translate pin number in GPIO ACPI callbacks
  gpio: mpc8xxx: remove __initdata annotation for mpc8xxx_gpio_ids[]

Pull ARM SoC fixes from Olof Johansson:
 "The latest and greatest fixes for ARM platform code.  Worth pointing
  out are:

   - Lines-wise, largest is a PXA fix for dealing with interrupts on DT
     that was quite broken.  It's still newish code so while we could
     have held this off, it seemed appropriate to include now

   - Some GPIO fixes for OMAP platforms added a few lines.  This was
     also fixes for code recently added (this release).

   - Small OMAP timer fix to behave better with partially upstreamed
     platforms, which is quite welcome.

   - Allwinner fixes about operating point control, reducing
     overclocking in some cases for better stability.

  plus a handful of other smaller fixes across the map"

* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: juno: Fix misleading name of UART reference clock
  ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
  ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
  ARM: socfpga: dts: fix spi1 interrupt
  ARM: dts: Fix gpio interrupts for dm816x
  ARM: dts: dra7: remove ti,hwmod property from pcie phy
  ARM: OMAP: dmtimer: disable pm runtime on remove
  ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
  ARM: OMAP2+: Fix socbus family info for AM33xx devices
  ARM: dts: omap3: Add missing dmas for crypto
  ARM: dts: rockchip: disable gmac by default in rk3288.dtsi
  MAINTAINERS: add rockchip regexp to the ARM/Rockchip entry
  ARM: pxa: fix pxa interrupts handling in DT
  ARM: pxa: Fix typo in zeus.c
  ARM: sunxi: Have ARCH_SUNXI select RESET_CONTROLLER for clock driver usage

Merge tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes

Allwinner fixes for 4.0

There's a few fixes to merge for 4.0, one to add a select in the machine
Kconfig option to fix a potential build failure, and two fixing cpufreq related
issues.

* tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
  ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
  ARM: sunxi: Have ARCH_SUNXI select RESET_CONTROLLER for clock driver usage
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for the -rc cycle:

- Fix a device tree based booting vs legacy booting regression for
  omap3 crypto hardware by adding the missing DMA channels.

- Fix /sys/bus/soc/devices/soc0/family for am33xx devices.

- Fix two timer issues that can cause hangs if the timer related
  hwmod data is missing like it often initially is for new SoCs.

- Remove pcie hwmods entry from dts as that causes runtime PM to
  fail for the PHYs.

- A paper bag type dts configuration fix for dm816x GPIO
  interrupts that I just noticed. This is most of the changes
  diffstat wise, but as it's a basic feature for connecting
  devices and things work otherwise, it should be fixed.

* tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: Fix gpio interrupts for dm816x
  ARM: dts: dra7: remove ti,hwmod property from pcie phy
  ARM: OMAP: dmtimer: disable pm runtime on remove
  ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
  ARM: OMAP2+: Fix socbus family info for AM33xx devices
  ARM: dts: omap3: Add missing dmas for crypto
Signed-off-by: Olof Johansson <olof@lixom.net>

Late fix for v4.0 on the SoCFPGA platform:
- Fix interrupt number for SPI1 interface

* tag 'socfpga_fix_for_v4.0_2' of git://git.rocketboards.org/linux-socfpga-next:
  ARM: socfpga: dts: fix spi1 interrupt
Signed-off-by: Olof Johansson <olof@lixom.net>

The UART reference clock speed is 7273.8 kHz, not 72738 kHz.

Dots aren't usually used in node names even though ePAPR permits
them.  However, this can easily be avoided by expressing the
frequency in Hz, not kHz.

This patch changes the name to refclk7273800hz, reflecting the
actual clock speed.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

arm: pxa: fixes for v4.0-rc5

There are only 2 fixes, one for the zeus board about the regulator changes,
where a typo prevented the zeus board from having a working can regulator,
and one regression triggered by the interrupts IRQ shift of 16 affecting all
boards.

* tag 'fixes-for-v4.0-rc5' of https://github.com/rjarzmik/linux:
  ARM: pxa: fix pxa interrupts handling in DT
  ARM: pxa: Fix typo in zeus.c
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull x86 fix from Ingo Molnar:
 "Fix x86 syscall exit code bug that resulted in spurious non-execution
  of TIF-driven user-return worklets, causing big trouble for things
  like KVM that rely on user notifiers for correctness of their vcpu
  model, causing crashes like double faults"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm/entry: Check for syscall exit work with IRQs disabled

Pull timer fixes from Ingo Molnar:
 "Two clocksource driver fixes, and an idle loop RCU warning fix"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/sun5i: Fix cpufreq interaction with sched_clock()
  clocksource/drivers: Fix various !CONFIG_HAS_IOMEM build errors
  timers/tick/broadcast-hrtimer: Fix suspicious RCU usage in idle loop

Pull scheduler fix from Ingo Molnar:
 "A single sched/rt corner case fix for RLIMIT_RTIME correctness"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix RLIMIT_RTTIME when PI-boosting to RT

Pull perf fix from Ingo Molnar:
 "A perf kernel side fix for a fuzzer triggered lockup"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix irq_work 'tail' recursion

Pull locking fix from Ingo Molnar:
 "A module unload lockdep race fix"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  lockdep: Fix the module unload key range freeing logic

Pull parsic fixes from Helge Deller:
 "One patch from Mikulas fixes a bug on parisc by artifically
  incrementing the counter in pmd_free when the kernel tries to free
  the preallocated pmd.

  Other than that we now prevent that syscalls gets added without
  incrementing __NR_Linux_syscalls and fix the initial pmd setup code
  if a default page size greater than 4k has been selected"

* 'parisc-4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix pmd code to depend on PT_NLEVELS value, not on CONFIG_64BIT
  parisc: mm: don't count preallocated pmds
  parisc: Add compile-time check when adding new syscalls

Pull kvm ppc bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: PPC: Book3S HV: Fix instruction emulation
  KVM: PPC: Book3S HV: Endian fix for accessing VPA yield count
  KVM: PPC: Book3S HV: Fix spinlock/mutex ordering issue in kvmppc_set_lpcr()

Pull ARC fixes from Vineet Gupta:
 "We found some issues with signal handling taking down the system.  I
  know its late, but these are important and all marked for stable.

  ARC signal handling related fixes uncovered during recent testing of
  NPTL tools"

* tag 'arc-4.0-fixes-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: signal handling robustify
  ARC: SA_SIGINFO ucontext regs off-by-one

Pull selinux bugfix from James Morris.

Fix broken return value.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  selinux: fix sel_write_enforce broken return value

Pull watchdog fixes from Wim Van Sebroeck:

 - mtk_wdt: signedness bug in mtk_wdt_start()

 - imgpdc: Fix NULL pointer dereference during probe and fix the default
   heartbeat

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: imgpdc: Fix default heartbeat
  watchdog: imgpdc: Fix probe NULL pointer dereference
  watchdog: mtk_wdt: signedness bug in mtk_wdt_start()

Pull sound fixes from Takashi Iwai:
 "Three trivial oneliner fixes for HD-audio.

  Two are device-specific quirks while one is a generic fix for recent
  Realtek codecs"

* tag 'sound-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Add one more node in the EAPD supporting candidate list
  ALSA: hda_intel: apply the Seperate stream_tag for Sunrise Point
  ALSA: hda - Add dock support for Thinkpad T450s (17aa:5036)

Now GPIO syscon driver produces bunch of warnings during the
boot of Kesytone 2 SoCs:
 gpio-syscon soc:keystone_dsp_gpio@02620240: can't read the dir register offset!
 gpio-syscon soc:keystone_dsp_gpio@2620244: can't read the dir register offset!

This message unintentionally was added using dev_err(), but its
actual log level is debug, because third cell of "ti,syscon-dev" is
optional.

Hence change it to dev_dbg() as it should be.

This patch fixes commit:
 5a3e3f88 ("gpio: syscon: retriave syscon node and regs offsets from dt")
Reported-by: Russell King <linux@arm.linux.org.uk>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The IMG PDC watchdog driver heartbeat module parameter has no default so
it is initialised to zero. This results in the following warning during
probe:

imgpdc-wdt 2006000.wdt: Initial timeout out of range! setting max timeout

The module parameter description implies that the default value should
be PDC_WDT_DEF_TIMEOUT, which isn't yet used, so initialise it to that.

Also tweak the heartbeat module parameter description for consistency.

Fixes: 93937669 ("watchdog: ImgTec PDC Watchdog Timer Driver")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Naidu Tellapati <Naidu.Tellapati@imgtec.com>
Cc: Jude Abraham <Jude.Abraham@imgtec.com>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The IMG PDC watchdog probe function calls pdc_wdt_stop() prior to
watchdog_set_drvdata(), causing a NULL pointer dereference when
pdc_wdt_stop() retrieves the struct pdc_wdt_dev pointer using
watchdog_get_drvdata() and reads the register base address through it.

Fix by moving the watchdog_set_drvdata() call earlier, to where various
other pdc_wdt->wdt_dev fields are initialised.

Fixes: 93937669 ("watchdog: ImgTec PDC Watchdog Timer Driver")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Naidu Tellapati <Naidu.Tellapati@imgtec.com>
Cc: Jude Abraham <Jude.Abraham@imgtec.com>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

"ret" should be signed for the error handling to work correctly.  This
doesn't matter much in real life since mtk_wdt_set_timeout() always
succeeds.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Pull drm refcounting fixes from Dave Airlie:
 "Here is the complete set of i915 bug/warn/refcounting fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: Fixup legacy plane->crtc link for initial fb config
  drm/i915: Fix atomic state when reusing the firmware fb
  drm/i915: Keep ring->active_list and ring->requests_list consistent
  drm/i915: Don't try to reference the fb in get_initial_plane_config()
  drm: Fixup racy refcounting in plane_force_disable

Pull device mapper fix from Mike Snitzer:
 "Fix DM core device cleanup regression -- due to a latent race that was
  exposed by the bdi changes that were introduced during the 4.0 merge"

* tag 'dm-4.0-fix-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm: fix add_disk() NULL pointer due to race with free_dev()

Merge tag 'linux-kselftest-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest fix from Shuah Khan.

* tag 'linux-kselftest-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests: Fix build failures when invoked from kselftest target

This should cover the final warnings in -rc5 with two more backports
from our development branch (drm-intel-next-queued). They're the ones
from Daniel and Damien, with references to the reports.

This is on top of drm-fixes because of the dependency on the two earlier
fixes not yet in Linus' tree.

There's an additional regression fix from Chris.

* tag 'drm-intel-fixes-2015-03-26' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Fixup legacy plane->crtc link for initial fb config
  drm/i915: Fix atomic state when reusing the firmware fb
  drm/i915: Keep ring->active_list and ring->requests_list consistent

Pull s390 fixes from Martin Schwidefsky:
 "A couple of bug fixes for s390.

  The ftrace comile fix is quite large for a -rc6 release, but it would
  be nice to have it in 4.0"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/smp: reenable smt after resume
  s390/mm: limit STACK_RND_MASK for compat tasks
  s390/ftrace: fix compile error if CONFIG_KPROBES is disabled
  s390/cpum_sf: add diagnostic sampling event only if it is authorized

This is a very similar bug in the load detect code fixed in

commit 9128b040
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Tue Mar 3 17:31:21 2015 +0100

    drm/i915: Fix modeset state confusion in the load detect code

But this time around it was the initial fb code that forgot to update
the plane->crtc pointer. Otherwise it's the exact same bug, with the
exact same restrains (any set_config call/ioctl that doesn't disable
the pipe papers over the bug for free, so fairly hard to hit in normal
testing). So if you want the full explanation just go read that one
over there - it's rather long ...

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reported-and-tested-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: backported to drm-intel-fixes for v4.0-rc]
Reference: http://mid.gmane.org/CA+5PVA7ChbtJrknqws1qvZcbrg1CW2pQAFkSMURWWgyASRyGXg@mail.gmail.comSigned-off-by: Jani Nikula <jani.nikula@intel.com>

Right now, we get a warning when taking over the firmware fb:

  [drm:drm_atomic_plane_check] FB set but no CRTC

with the following backtrace:

  [<ffffffffa010339d>] drm_atomic_check_only+0x35d/0x510 [drm]
  [<ffffffffa0103567>] drm_atomic_commit+0x17/0x60 [drm]
  [<ffffffffa00a6ccd>] drm_atomic_helper_plane_set_property+0x8d/0xd0 [drm_kms_helper]
  [<ffffffffa00f1fed>] drm_mode_plane_set_obj_prop+0x2d/0x90 [drm]
  [<ffffffffa00a8a1b>] restore_fbdev_mode+0x6b/0xf0 [drm_kms_helper]
  [<ffffffffa00aa969>] drm_fb_helper_restore_fbdev_mode_unlocked+0x29/0x80 [drm_kms_helper]
  [<ffffffffa00aa9e2>] drm_fb_helper_set_par+0x22/0x50 [drm_kms_helper]
  [<ffffffffa050a71a>] intel_fbdev_set_par+0x1a/0x60 [i915]
  [<ffffffff813ad444>] fbcon_init+0x4f4/0x580

That's because we update the plane state with the fb from the firmware, but we
never associate the plane to that CRTC.

We don't quite have the full DRM take over from HW state just yet, so
fake enough of the plane atomic state to pass the checks.

v2: Fix the state on which we set the CRTC in the case we're sharing the
    initial fb with another pipe. (Matt)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: backported to drm-intel-fixes for v4.0-rc]
Reference: http://mid.gmane.org/CA+5PVA7yXH=U757w8V=Zj2U1URG4nYNav20NpjtQ4svVueyPNw@mail.gmail.com
Reference: http://lkml.kernel.org/r/CA+55aFweWR=nDzc2Y=rCtL_H8JfdprQiCimN5dwc+TgyD4Bjsg@mail.gmail.comSigned-off-by: Jani Nikula <jani.nikula@intel.com>

We have a HP machine which use the codec node 0x17 connecting the
internal speaker, and from the node capability, we saw the EAPD,
if we don't set the EAPD on for this node, the internal speaker
can't output any sound.

Cc: <stable@vger.kernel.org>
BugLink: https://bugs.launchpad.net/bugs/1436745Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The sun5i timer is used as the sched-clock on certain systems, and ever
since we started using cpufreq, the cpu clock (that is one of the
timer's clock indirect parent) now changes as well, along with the
actual sched_clock() rate.

This is not accurate and not desirable.

We can safely remove the sun5i sched-clock on those systems, since we
have other reliable sched_clock() sources in the system.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ Improved the changelog. ]
Cc: richard@nod.at
Link: http://lkml.kernel.org/r/1427362029-6511-4-git-send-email-daniel.lezcano@linaro.orgSigned-off-by: Ingo Molnar <mingo@kernel.org>

Fix !CONFIG_HAS_IOMEM related build failures in three clocksource drivers.

The build failures have the pattern of:

  drivers/clocksource/sh_cmt.c: In function ‘sh_cmt_map_memory’: drivers/clocksource/sh_cmt.c:920:2:
  error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration]   cmt->mapbase = ioremap_nocache(mem->start, resource_size(mem));
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: maxime.ripard@free-electrons.com
Link: http://lkml.kernel.org/r/1427362029-6511-1-git-send-email-daniel.lezcano@linaro.orgSigned-off-by: Ingo Molnar <mingo@kernel.org>

If we retire requests last, we may use a later seqno and so clear
the requests lists without clearing the active list, leading to
confusion. Hence we should retire requests first for consistency with
the early return. The order used to be important as the lifecycle for
the object on the active list was determined by request->seqno. However,
the requests themselves are now reference counted removing the
constraint from the order of retirement.

Fixes regression from

commit 1b5a433a
Author: John Harrison <John.C.Harrison@Intel.com>
Date:   Mon Nov 24 18:49:42 2014 +0000

    drm/i915: Convert 'i915_seqno_passed' calls into 'i915_gem_request_completed
'

and a

	WARNING: CPU: 0 PID: 1383 at drivers/gpu/drm/i915/i915_gem_evict.c:279 i915_gem_evict_vm+0x10c/0x140()
	WARN_ON(!list_empty(&vm->active_list))

Identified by updating WATCH_LISTS:

	[drm:i915_verify_lists] *ERROR* blitter ring: active list not empty, but no requests
	WARNING: CPU: 0 PID: 681 at drivers/gpu/drm/i915/i915_gem.c:2751 i915_gem_retire_requests_ring+0x149/0x230()
	WARN_ON(i915_verify_lists(ring->dev))

Note that this is only a problem in evict_vm where the following happens
after a retire_request has cleaned out all requests, but not all active
bo:
- intel_ring_idle called from i915_gpu_idle notices that no requests are
  outstanding and immediately returns.
- i915_gem_retire_requests_ring called from i915_gem_retire_requests also
  immediately returns when there's no request, still leaving the bo on the
  active list.
- evict_vm hits the WARN_ON(!list_empty(&vm->active_list)) after evicting
  all active objects that there's still stuff left that shouldn't be
  there.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

The total stream number of Sunrise Point's input and output stream
exceeds 15, which will cause some streams do not work because
of the overflow on SDxCTL.STRM field if using the legacy
stream tag allocation method.

This patch uses the new stream tag allocation method by add
the flag AZX_DCAPS_SEPARATE_STREAM_TAG for Skylake platform.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

A malicious signal handler / restorer can DOS the system by fudging the
user regs saved on stack, causing weird things such as sigreturn returning
to user mode PC but cpu state still being kernel mode....

Ensure that in sigreturn path status32 always has U bit; any other bogosity
(gargbage PC etc) will be taken care of by normal user mode exceptions mechanisms.

Reproducer signal handler:

    void handle_sig(int signo, siginfo_t *info, void *context)
    {
	ucontext_t *uc = context;
	struct user_regs_struct *regs = &(uc->uc_mcontext.regs);

	regs->scratch.status32 = 0;
    }

Before the fix, kernel would go off to weeds like below:

    --------->8-----------
    [ARCLinux]$ ./signal-test
    Path: /signal-test
    CPU: 0 PID: 61 Comm: signal-test Not tainted 4.0.0-rc5+ #65
    task: 8f177880 ti: 5ffe6000 task.ti: 8f15c000

    [ECR   ]: 0x00220200 => Invalid Write @ 0x00000010 by insn @ 0x00010698
    [EFA   ]: 0x00000010
    [BLINK ]: 0x2007c1ee
    [ERET  ]: 0x10698
    [STAT32]: 0x00000000 :                                   <--------
    BTA: 0x00010680	 SP: 0x5ffe7e48	 FP: 0x00000000
    LPS: 0x20003c6c	LPE: 0x20003c70	LPC: 0x00000000
    ...
    --------->8-----------
Reported-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

The regfile provided to SA_SIGINFO signal handler as ucontext was off by
one due to pt_regs gutter cleanups in 2013.

Before handling signal, user pt_regs are copied onto user_regs_struct and copied
back later. Both structs are binary compatible. This was all fine until
commit 2fa91904 (ARC: pt_regs update #2) which removed the empty stack slot
at top of pt_regs (corresponding to first pad) and made the corresponding
fixup in struct user_regs_struct (the pad in there was moved out of
@scratch - not removed altogether as it is part of ptrace ABI)

 struct user_regs_struct {
+       long pad;
        struct {
-               long pad;
                long bta, lp_start, lp_end,....
        } scratch;
 ...
 }

This meant that now user_regs_struct was off by 1 reg w.r.t pt_regs and
signal code needs to user_regs_struct.scratch to reflect it as pt_regs,
which is what this commit does.

This problem was hidden for 2 years, because both save/restore, despite
using wrong location, were using the same location. Only an interim
inspection (reproducer below) exposed the issue.

     void handle_segv(int signo, siginfo_t *info, void *context)
     {
 	ucontext_t *uc = context;
	struct user_regs_struct *regs = &(uc->uc_mcontext.regs);

	printf("regs %x %x\n",               <=== prints 7 8 (vs. 8 9)
               regs->scratch.r8, regs->scratch.r9);
     }

     int main()
     {
	struct sigaction sa;

	sa.sa_sigaction = handle_segv;
	sa.sa_flags = SA_SIGINFO;
	sigemptyset(&sa.sa_mask);
	sigaction(SIGSEGV, &sa, NULL);

	asm volatile(
	"mov	r7, 7	\n"
	"mov	r8, 8	\n"
	"mov	r9, 9	\n"
	"mov	r10, 10	\n"
	:::"r7","r8","r9","r10");

	*((unsigned int*)0x10) = 0;
     }

Fixes: 2fa91904 "ARC: pt_regs update #2: Remove unused gutter at start of pt_regs"
CC: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Pull arch/metag fix from James Hogan:
 "Another metag architecture fix for v4.0

  This is another single fix, for an include dependency problem when
  using ioremap_wc() from asm/io.h without also including asm/pgtable.h"

* tag 'metag-fixes-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
  metag: Fix ioremap_wc/ioremap_cached build errors

Merge misc fixes from Andrew Morton:
 "15 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: numa: mark huge PTEs young when clearing NUMA hinting faults
  mm: numa: slow PTE scan rate if migration failures occur
  mm: numa: preserve PTE write permissions across a NUMA hinting fault
  mm: numa: group related processes based on VMA flags instead of page table flags
  hfsplus: fix B-tree corruption after insertion at position 0
  MAINTAINERS: add Jan as DMI/SMBIOS support maintainer
  fs/affs/file.c: unlock/release page on error
  mm/page_alloc.c: call kernel_map_pages in unset_migrateype_isolate
  mm/slub: fix lockups on PREEMPT && !SMP kernels
  mm/memory hotplug: postpone the reset of obsolete pgdat
  MAINTAINERS: correct rtc armada38x pattern entry
  mm/pagewalk.c: prevent positive return value of walk_page_test() from being passed to callers
  mm: fix anon_vma->degree underflow in anon_vma endless growing prevention
  drivers/rtc/rtc-mrst: fix suspend/resume
  aoe: update aoe maintainer information