mxs-lradc.c uses many input_() functions so it should
depend on INPUT to fix build errors.

drivers/built-in.o: In function `mxs_lradc_ts_unregister':
drivers/staging/iio/adc/mxs-lradc.c:905: undefined reference to `input_unregister_device'
drivers/staging/iio/adc/mxs-lradc.c:905: undefined reference to `input_unregister_device'
drivers/built-in.o: In function `input_report_abs':
include/linux/input.h:399: undefined reference to `input_event'
include/linux/input.h:399: undefined reference to `input_event'
include/linux/input.h:399: undefined reference to `input_event'
drivers/built-in.o: In function `input_report_key':
include/linux/input.h:389: undefined reference to `input_event'
drivers/built-in.o: In function `input_sync':
include/linux/input.h:414: undefined reference to `input_event'
drivers/built-in.o:include/linux/input.h:389: more undefined references to `input_event' follow
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The driver currently supports only I2C access. But supported devices with an
accuracy of 8-bit are compatible with the SMBus byte access routines.

This patch wraps the send and receive routines depending on the chip
accuracy and fonctionnalities of its adapter.

For instance, this allows us to use a MAX11603 on a ICH7 controller.

This patch also simplifies the max1363_write_basic_config() routine to
use the struct max1363_state fields directly.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

this just fixes the comment; however, I'm not sure if the driver reports
measurements correctly; the raw values are 0.3 uT / LSB; IIO is supposed
to report magnetic fields in Gauss, so the scale should be around 1/300
(ignoring ASA) -- but value and scale are returned as VAL_INT
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Fix the following checkpatch.pl errors:

drivers/staging/rtl8187se/ieee80211/ieee80211_softmac.c:890: "foo* bar" should be "foo *bar"
drivers/staging/rtl8187se/ieee80211/ieee80211_softmac.c:944: "foo* bar" should be "foo *bar"
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes sparse warnings regarding functions that should be
static in driver rtl8187se.
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the following type of sparse warnings:

drivers/staging/rtl8187se/r8180_core.c:163:48: warning: incorrect type in argument 1 (different address spaces)
drivers/staging/rtl8187se/r8180_core.c:163:48:    expected void const volatile [noderef] <asn:2>*addr
drivers/staging/rtl8187se/r8180_core.c:163:48:    got unsigned char [usertype] *
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the following type of sparse warnings:

drivers/staging/rtl8187se/ieee80211/ieee80211_tx.c:249:17: warning: incorrect type in argument 2 (different base types)
drivers/staging/rtl8187se/ieee80211/ieee80211_tx.c:249:17:    expected restricted gfp_t [usertype] flags
drivers/staging/rtl8187se/ieee80211/ieee80211_tx.c:249:17:    got int [signed] gfp_mask
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the following Sparse information in sb_pci_mp.c-

~/git/kernels/linux/drivers/staging/sb105x/sb_pci_mp.c:1813
mp_unregister_driver() info: redundant null check on drv->state calling kfree()
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/line6/driver.c:208 line6_send_raw_message_async_part()
info: why not propagate 'retval' from usb_submit_urb() instead of (-22)?
Signed-off-by: Ashvini Varatharaj <ashvinivaratharaj@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/line6/midi.c:147 send_midi_async() info: why not
propagate 'retval' from usb_submit_urb() instead of (-22)?
Signed-off-by: Ashvini Varatharaj <ashvinivaratharaj@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix checkpatch warning: WARNING: simple_strtoul is obsolete, use
kstrtoul instead
Signed-off-by: Ashvini Varatharaj <ashvinivaratharaj@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the following smatch warning-

~/git/kernels/linux/drivers/staging/sep/sep_crypto.c:1137
sep_crypto_block_data() info: why not propagate 'int_error' from sep_oddball_pages() instead of (-12)?
~/git/kernels/linux/drivers/staging/sep/sep_crypto.c:1152
sep_crypto_block_data() info: why not propagate 'int_error' from sep_oddball_pages() instead of (-12)?
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes C99 commenting style in staging:vt6655:michael.h
Signed-off-by: Archana kumari <archanakumari959@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the following checkpatch.pl warning in slicoss.c-
WARNING: quoted string split across lines
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the following checkpatch.pl warning in slicoss.c:
WARNING: Too many leading tabs - consider code refactoring
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the following checkpatch.pl warning in slicoss.c:
WARNING: Prefer netdev_dbg(netdev, ... then dev_dbg(dev, ... then
pr_debug(...  to printk(KERN_DEBUG ...
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the following checkpatch.pl warning in slicoss.c:
WARNING: debugfs_remove(NULL) is safe this check is probably not
required
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/dgnc/dgnc_neo.c:1969 neo_vpd() error: buffer overflow 'brd->vpd' 128 <= 128
drivers/staging/dgnc/dgnc_neo.c:1970 neo_vpd() warn: buffer overflow 'brd->vpd' 128 <= 130
drivers/staging/dgnc/dgnc_neo.c:1970 neo_vpd() warn: buffer overflow 'brd->vpd' 128 <= 130
Signed-off-by: Ashvini Varatharaj <ashvinivaratharaj@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix dgnc_mgmt_ioctl() warn: unsigned 'board' is never less than zero.
Signed-off-by: Ashvini Varatharaj <ashvinivaratharaj@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes "braces {} are not necessary for single statement blocks" warning
in dgnc_driver.c
Signed-off-by: Archana kumari <archanakumari959@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed removal of unecessary error messages in staging:dgnc:dgnc_driver.c
Signed-off-by: Archana kumari <archanakumari959@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes sparse warning "Using plain integer as NULL pointer" in
sta_h2.c
Signed-off-by: Archana kumari <archanakumari959@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the following warnings in hcf.c:
"space prohibited between function name and open parenthesis '(' "

"space prohibited before that close parenthesis ')' ".
Signed-off-by: Archana kumari <archanakumari959@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some bits of the 'CRB' register have different functions when read or
written, so add macros to define the read-only parts.

Add macros to define the widths of the bitfields in the 'CRA' and 'CRB'
registers and the standard encoder setup value.

Add macros to construct and extract parts of the 'CRA' and 'CRB'
register values and the standard encoder setup value, along with a
couple of general helper macros for the above.

Redefine the bitfield mask macros for 'CRA', 'CRB' and standard encoder
setup using the above.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There are some bits in the 'CRB' register not defined in "s626.h".
Three of these are read-only bits that overlay the write-only interrupt
control bits.  Another missing bit controls whether counter 'B' is
cleared when counter 'A' overflows.  Add the missing bit definitions for
completeness.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The counter 'A' clock polarity field in the 'CRA' register is only 1 bit
wide, but the `S626_CRAMSK_CLKPOL_A` macro shows it as 2 bits wide,
which would overlap with the counter 'A' interrupt source field.  This
is harmless as the macro isn't actually used yet, but correct it anyway
as I want to use it!
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The macros `S626_CLKSRC_COUNTER`, `S626_CLKSRC_TIMER` and
`S626_CLKSRC_EXTENDER` are used logically to set the operating mode of
an encoder channel.  `S626_CLKSRC_COUNTER` (0) is also used as a 2-bit
physical value to set the counter source of an encoder channel to
"encoder".

Rename the macros to `S626_ENCMODE_COUNTER`, `S626_ENCMODE_TIMER` and
`S626_ENCMODE_EXTENDER` and rename some other macros and (unused)
functions relating to the encoder mode for consistency.

Define new macros to specify the physical counter source values for the
'CRA' register and rename the corresponding bitshift and mask macros
accordingly.  The physical values for the counter source are:

  S626_CNTSRC_ENCODER = 0      // encoder
  S626_CNTSRC_DIGIN = 1        // digital inputs
  S626_CNTSRC_SYSCLK = 2       // system clock up
  S626_CNTSRC_SYSCLK_DOWN = 3  // system clock down

Also use the `S626_CNTSRC_SYSCLK` value as a bitmask (bit 1) to indicate
either of the system clock values, with the direction (bit 0) indicated
separately in this case.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When setting the clock source for one of the 'A' encoders to operate in
"counter" mode in `s626_set_mode_a()`, bitshift the clock source value by
`S626_CRABIT_CLKSRC_A` for consistency with the other modes.  This has
no effect on the value since `S626_CRABIT_CLKSRC_A` is 0.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When setting up an encoder channel, the setup value includes a polarity
and direction, but these are the same bit of the setup value:

  S626_CLKPOL_POS = S626_CNTDIR_UP = 0

  S626_CLKPOL_NEG = S626_CNTDIR_DOWN = 1

In the construction of the setup value, both the CLKPOL and the CNTDIR
constants are shifted by the same amount `S626_BF_CLKPOL`.  Only the
following combinations are set up currently (this may change if user
configuration of the encoder is implemented properly):

  (S626_CLKPOL_POS << S626_BF_CLKPOL)

  (S626_CLKPOL_POS << S626_BF_CLKPOL) |
  (S626_CNTDIR_UP << S626_BF_CLKPOL)

  (S626_CLKPOL_POS << S626_BF_CLKPOL) |
  (S626_CNTDIR_DOWN << S626_BF_CLKPOL)

The first two are used in "counter" mode and is equivalent to:

  (S626_CLKPOL_POS << S626_BF_CLKPOL)

The last one is used in "timer" mode and is equivalent to:

  (S626_CNTDIR_DOWN << S626_BF_CLKPOL)

Use the shorter equivalents.  The comments in "s626.h" indicate that the
'CLKPOL' constants make more sense for the "counter" mode (when the
encoders operate as up/down counters) and the 'CNTDIR' constants make
more sense for the "timer" mode.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The `unsigned char chan_is_bipolar[]` member of `struct rtd_private` is
used with some macros as a packed array of 1-bit values that indicate
whether the corresponding entries in the hardware's "channel-gain" table
have been set to a bipolar (1) or unipolar (0) range, as the raw samples
from the hardware need to be cooked differently in each case.

Replace the declaration of the member with a standard Linux bitfield
using `DECLARE_BITFIELD()`, and replace the home-grown macros used
access the bitfield with the standard Linux non-atomic bitop functions,
`__set_bit()`, `__clear_bit()` and `test_bit()`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed two coding style issues, specifically:

ft1000_proc.c:35: ERROR: space required before the open parenthesis '('
ft1000_proc.c:42: ERROR: space required before the open parenthesis '('
Signed-off-by: Aldo Iljazi <me@aldo.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is necessary so that xillybus_core uses the correct device pointer
for PCIe devices in diagnostic message calls (dev_err, dev_warn and dev_info)
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove unnecessary spaces between function names and open
parentheses in router_proc.c to meet kernel coding style.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed the static initialization error generated by checkpatch.pl to
meet kernel coding standards.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Reformat a pointer variable in lib-move.c to meet kernel
coding standards.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove unnecessary parentheses from return statements to
eliminate errors generated by checkpatch.pl and meet kernel
coding standards.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>