This patch indicates that the at86rf230 driver deliver with checksum
instead drop the crc before delivering.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds error handling after skb_clone and deliver only if
skb_clone was successful.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch replace the !netif_running(sdata->dev) instead we doing a
!ieee802154_sdata_running(sdata). Also move this in two separate if
branches to compare with mac80211 code.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds rx stats incrementation when the monitor interface
recevied a frame.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes netif_rx_ni call. Instead we call netif_receive_skb,
we can do that since commit c5c47e67
("mac802154: rx: use tasklet instead workqueue").
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes pkt_type set to PACKET_HOST while monitor receiving.
This should be PACKET_OTHERHOST on monitor mode which already set
before.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds a new hardware flag which indicate that the transceiver
doesn't support check for bad checksum via hardware. Also add a handling of
this while receive.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch change the actual crc handling while receive. Currently the
IEEE802154_HW_RX_OMIT_CKSUM flag is used to filter a frame with a bad crc.
This patch changes the behaviour of IEEE802154_HW_RX_OMIT_CKSUM to add a
crc while receiving for the monitor interface. After monitor receiving
we remove the crc for frame parsing. This affect the driver layer
because all drivers sets IEEE802154_HW_RX_OMIT_CKSUM and deliver without
checksum.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes a not used parameter in ieee802154_deliver_skb.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch splits the IEEE802154_HW_OMIT_CKSUM hardware flag into
IEEE802154_HW_TX_OMIT_CKSUM and IEEE802154_HW_RX_OMIT_CKSUM. This is
useful to deliver the received crc from the driver layer to the monitor
interface. At the moment we can't do that without change the xmit
handling.

The received checksum should be visible in monitor mode only.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds support for promiscuous mode setting for the at86rf230
driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds a new driver operation to bring the transceiver into
promiscuous mode.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Overdue introduction for address filtering hardware flag. Furthermore we
will check and set address filtering on interface up. This patch
prepares that we can check if an transceiver supports address filtering
option. Currently all mainline driver supports hardware address filtering.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds a new IEEE802154_HW_ARET hardware flag for indicating
that the transceiver supports ARET handling. Also remove the
IEEE802154_HW_FRAME_RETRIES from IEEE802154_HW_CSMA flag. Frame retries
handling is part of ARET.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes tabs after define in hardware flags declarations.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes an unnecessary include of driver-ops header file.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds maintainer for cc2520 radio driver
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Use spin_lock_bh() as the code is called from softirq in networking subsystem.
This is needed to prevent deadlocks when 6lowpan link is in use.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch moves the sysfs handling in a own file. This is like wireless
sysfs file handling.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch cleanups the open_count variable increment in open and close
calls of netdev.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

These functions can be static in mac_cmd file.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

These channel attributes was part of "channel context switch while xmit"
which was removed by commit dc67c6b3
("mac802154: tx: remove xmit channel context switch"). This patch
removes these unnecessary variables and use the current_page and
current_channel by wpan_phy struct now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

These variables should already be zero, so we remove the extra assign to
zero.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds synchronization handling in start and stop driver ops
calls. This patch is mostly grab from mac80211 which was introduced by
commit ea77f12f ("mac80211: remove
tasklet enable/disable"). This is to be sure that we don't run into same
issues.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes the current handling of started boolean. This is
actually dead code, because mac802154_netdev_register can't never be
called before ieee802154_register_hw. This means that local->started is
always be true when mac802154_netdev_register is called. Instead we
using this now like mac80211 to indicate that an instance of sdata is
running.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This variable should be handled like ieee80211_local struct of mac80211.
We rename this variable to started now to have the same name convention.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch reworks the handling for setting the state like mac80211. We
use bit's instead a bool variable. The mutex is not needed because it use
test and set bits which are atomic operations.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes the driver ops callbacks inside of wpan_phy struct.
It was used to check if a phy supports this driver ops call. We do this
now via hardware flags.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes all might_sleep calls from driver layer. This
handling is already done by mac802154 layer.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch replaces all directly called driver ops by previous
introduced driver-ops function wrappers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch introduce a driver-ops header file with function wrappers to
call the driver ops. These wrappers checking on right context
information and warn if optional driver ops are called when these aren't
implemented. This behaviour is like mac80211 driver-ops header file,
just without function tracing calls.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The range of channel and page fits into an unsigned byte range. This
patch changes the set_channel parameter definitions for channel and
page to u8.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The ieee802154_ops structure should be never changed during runtime.
This patch declare this structure as const to avoid a runtime change.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

These functions can be static inside the iface file, because it's not
used anywhere else. This patch moves these functions into iface file.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes the monitor implementation file and put all monitor
stuff into iface file. It's now small enough to put all necessary
handling into iface.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

These days we allow simultaneous LE scanning and advertising. Checking
for whether advertising is enabled or not is therefore not a reliable
way to determine whether directed advertising was used to trigger the
connection creation. The appropriate place to check (instead of the hdev
context) is the connection role that's stored in the hci_conn. This
patch fixes such a check in le_conn_timeout() which could otherwise lead
to incorrect HCI commands being sent.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.16.x

The le_conn_timeout() may call hci_le_conn_failed() which in turn may
call hci_conn_del(). Trying to use the _sync variant for cancelling the
conn timeout from hci_conn_del() could therefore result in a deadlock.
This patch converts hci_conn_del() to use the non-sync variant so the
deadlock is not possible.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.16.x

Fix spelling errors in comments.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When a device ndo_start_xmit() calls again dev_queue_xmit(),
lockdep can complain because dev_queue_xmit() is re-entered and the
spinlocks protecting tx queues share a common lockdep class.

Same issue was fixed for ieee802154 in commit "20e7c4e8"
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The rwlocks are converted to use RCU. This helps performance as the
irq locks are not needed any more.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>