- 11 May, 2012 20 commits
-
-
Alexey Khoroshilov authored
commit e4459e16 upstream. If sanity check fails in scu_command(), goto error leads to unlock of an unheld mutex. The check should not fail in reality, but it nevertheless worth fixing. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
David Härdeman authored
commit d9b78695 upstream. Setting the correct mode is required by rc-core or scancodes won't be generated (which isn't very user-friendly). This one-line fix should be suitable for 3.4-rc2. Signed-off-by:
David Härdeman <david@hardeman.nu> Signed-off-by:
-
Arend van Spriel authored
commit badc4f07 upstream. There have been reports about not being able to use access-points on channel 12 and 13 or having connectivity issues when these channels were part of the selected regulatory domain. Upon switching to these channels the brcmsmac driver suspends the transmit dma fifos. This patch resumes them upon handing over the first received beacon to mac80211. This patch is to be applied to the stable tree for kernel versions 3.2 and 3.3. Tested-by:
Francesco Saverio Schiavarelli <fschiava@libero.it> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by:
Brett Rudley <brudley@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Bing Zhao authored
commit 428ca8a7 upstream. The scratch register addresses have been changed for newer chips. Since the old chip was never shipped and it will not be supported any more, just update register addresses to support the new chips. Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Christian Riesch authored
commit 5b76d060 upstream. Under heavy load (flood ping) it is possible for the MDIO timeout to expire before the loop checks the GO bit again. This patch adds an additional check whether the operation was done before actually returning -ETIMEDOUT. To reproduce this bug, flood ping the device, e.g., ping -f -l 1000 After some time, a "timed out waiting for user access" warning may appear. And even worse, link may go down since the PHY reported a timeout. Signed-off-by:
Christian Riesch <christian.riesch@omicron.at> Cc: Cyril Chemparathy <cyril@ti.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Oliver Neukum authored
commit 5bd7b419 upstream. Fatal errors such as a device disconnect must not trigger error handling. The error returns must be checked. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Oliver Neukum authored
commit 9426cd05 upstream. del_timer_sync() cannot be used in interrupt. Replace it with del_timer() and a flag Signed-off-by:
-
Tomoki Sekiyama authored
commit 532f17b5 upstream. Current probing code is setting URB_NO_TRANSFER_DMA_MAP flag into a wrong urb structure, and this causes BUG_ON with some USB host implementations. This patch fixes the issue. Signed-off-by:
Tomoki Sekiyama <tomoki.sekiyama@gmail.com> Signed-off-by:
-
Tomoki Sekiyama authored
commit 523fc5c1 upstream. Removes allocation of coherent buffer for the control-request setup-packet buffer from the yurex driver. Using coherent buffers for setup-packet is obsolete and does not work with some USB host implementations. Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit 3066616c upstream. A rather annoying and common case is when booting a PVonHVM guest and exposing the PV KBD and PV VFB - as broken toolstacks don't always initialize the backends correctly. Normally The HVM guest is using the VGA driver and the emulated keyboard for this (though upstream version of QEMU implements PV KBD, but still uses a VGA driver). We provide a very basic two-stage wait mechanism - where we wait for 30 seconds for all devices, and then for 270 for all them except the two mentioned. That allows us to wait for the essential devices, like network or disk for the full 6 minutes. To trigger this, put this in your guest config: vfb = [ 'vnc=1, vnclisten=0.0.0.0 ,vncunused=1'] instead of this: vnc=1 vnclisten="0.0.0.0" Acked-by:
Stefano Stabellini <stefano.stabellini@eu.citrix.com> [v3: Split delay in non-essential (30 seconds) and essential devices per Ian and Stefano suggestion] [v4: Added comments per Stefano suggestion] Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Stefano Stabellini authored
commit e8e937be upstream. Since we are using the m2p_override we do have struct pages corresponding to the user vma mmap'ed by gntdev. Removing the VM_PFNMAP flag makes get_user_pages work on that vma. An example test case would be using a Xen userspace block backend (QDISK) on a file on NFS using O_DIRECT. Signed-off-by:
-
Eric Bénard authored
commit b8915282 upstream. This was broken by me in 37865fe9 ("mmc: sdhci-esdhc-imx: fix timeout on i.MX's sdhci") where more extensive tests would have shown that read or write of data to the card were failing (even if the partition table was correctly read). Signed-off-by:
Eric Bénard <eric@eukrea.com> Acked-by:
Wolfram Sang <w.sang@pengutronix.de> Signed-off-by:
Chris Ball <cjb@laptop.org> Signed-off-by:
-
Adrian Hunter authored
commit 28302812 upstream. eMMC v4.5 sanitize operation erases all copies of unmapped data. However trim or erase operations must be used first to unmap the required sectors. That was not being done. Fixes apply to linux 3.2 on. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Acked-by:
Jaehoon Chung <jh80.chung@samsung.com> Acked-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Adrian Hunter authored
commit 7194efb8 upstream. eMMC v4.5 discard operation is significantly different from the existing trim operation because it is not guaranteed to work with the new sanitize operation. Consequently mmc_can_trim() is separated from mmc_can_discard(). Also the new discard operation does not result in the sectors being set to all-zeros, so discard_zeroes_data must not be set. In addition, the new discard has the same timeout as trim, but from v4.5 trim is defined to use the hc timeout. The timeout calculation is adjusted accordingly. Fixes apply to linux 3.2 on. Signed-off-by:
-
Paul Walmsley authored
commit 6aaec67d upstream. DMTIMER source selection on OMAP1 is broken. omap1_dm_timer_set_src() tries to use __raw_{read,write}l() to read from and write to physical addresses, but those functions take virtual addresses. sparse caught this: arch/arm/mach-omap1/timer.c:50:13: warning: incorrect type in argument 1 (different base types) arch/arm/mach-omap1/timer.c:50:13: expected void const volatile [noderef] <asn:2>*<noident> arch/arm/mach-omap1/timer.c:50:13: got unsigned int arch/arm/mach-omap1/timer.c:52:9: warning: incorrect type in argument 1 (different base types) arch/arm/mach-omap1/timer.c:52:9: expected void const volatile [noderef] <asn:2>*<noident> arch/arm/mach-omap1/timer.c:52:9: got unsigned int Fix by using omap_{read,writel}(), just like the other users of the MOD_CONF_CTRL_1 register in the OMAP1 codebase. Of course, in the long term, removing omap_{read,write}l() is the appropriate thing to do; but this will take some work to do this cleanly. Looks like this was caused by 97933d6c (ARM: OMAP1: dmtimer: conversion to platform devices) that dangerously moved code and changed it in the same patch. Signed-off-by:
Paul Walmsley <paul@pwsan.com> Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com> [tony@atomide.com: updated comments to include the breaking commit] Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Alexander Shiyan authored
commit 7a6fbc9a upstream. Since 2.6.30-rc1 clps711x serial driver hungs system. This is a result of call disable_irq from ISR. synchronize_irq waits for end of interrupt and goes to infinite loop. This patch fix this problem. Signed-off-by:
Alexander Shiyan <shc_work@mail.ru> Signed-off-by:
-
Takashi Iwai authored
commit d70f3632 upstream. ThinkPad 410,420,510,520 and X201 with cx50585 & co chips have the docking-station ports, but BIOS doesn't initialize for these pins. Thus, like the former X200, we need to set up the pins manually in the driver. The odd part is that the same PCI SSID is used for X200 and T400, thus we need to prepare individual fixup tables for cx5051 and others. Bugzilla entries: https://bugzilla.redhat.com/show_bug.cgi?id=808559 https://bugzilla.redhat.com/show_bug.cgi?id=806217 https://bugzilla.redhat.com/show_bug.cgi?id=810697Reported-by:
Josh Boyer <jwboyer@redhat.com> Reported-by:
Jens Taprogge <jens.taprogge@taprogge.org> Tested-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit ca3649de upstream. Some output pins on Conexant chips have no HP control bit, but the auto-parser initializes these pins unconditionally with PIN_HP. Check the pin-capability and avoid the HP bit if not supported. Signed-off-by:
-
Kent Yoder authored
commit 25c3d30c upstream. The current code only increments the upper 64 bits of the SHA-512 byte counter when the number of bytes hashed happens to hit 2^64 exactly. This patch increments the upper 64 bits whenever the lower 64 bits overflows. Signed-off-by:
Kent Yoder <key@linux.vnet.ibm.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Zeev Tarantov authored
[Patch not needed upstream as this is a backport build bugfix - gregkh gcc correctly complains: util/hist.c: In function ‘__hists__add_entry’: util/hist.c:240:27: error: invalid type argument of ‘->’ (have ‘struct hist_entry’) util/hist.c:241:23: error: invalid type argument of ‘->’ (have ‘struct hist_entry’) for this new code: + if (he->ms.map != entry->ms.map) { + he->ms.map = entry->ms.map; + if (he->ms.map) + he->ms.map->referenced = true; + } because "entry" is a "struct hist_entry", not a pointer to a struct. In mainline, "entry" is a pointer to struct passed as argument to the function. So this is broken during backporting. But obviously not compile tested. Signed-off-by:Zeev Tarantov <zeev.tarantov@gmail.com> Cc: Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
- 22 Apr, 2012 20 commits
-
-
Greg Kroah-Hartman authored
-
Dave Airlie authored
commit a09d431f upstream. When the force changes went in back in 3.3.0, we ended up returning disconnected in the !force case, and the connected in when forced, as it hit the hardcoded check. Fix it so all exits go via the hardcoded check and stop spurious modesets on platforms with hardcoded EDIDs. Reported-by: Evan McNabb (Red Hat) Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Dave Airlie authored
commit 16a5e32b upstream. My rv515 card is very flaky with msi enabled. Every so often it loses a rearm and never comes back, manually banging the rearm brings it back. Reviewed-by:
-
Takashi Iwai authored
commit e3632507 upstream. The check of the encoder type in the commit [e00e8b5e: drm/radeon/kms: fix analog load detection on DVI-I connectors] is obviously wrong, and it's the culprit of the regression on my workstation with DVI-analog connection resulting in the blank output. Fixed the typo now. Signed-off-by:
-
Kees Cook authored
commit bdbb776f upstream. It was possible to extract the robust list head address from a setuid process if it had used set_robust_list(), allowing an ASLR info leak. This changes the permission checks to be the same as those used for similar info that comes out of /proc. Running a setuid program that uses robust futexes would have had: cred->euid != pcred->euid cred->euid == pcred->uid so the old permissions check would allow it. I'm not aware of any setuid programs that use robust futexes, so this is just a preventative measure. (This patch is based on changes from grsecurity.) Signed-off-by:
Kees Cook <keescook@chromium.org> Cc: Darren Hart <dvhart@linux.intel.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: David Howells <dhowells@redhat.com> Cc: Serge E. Hallyn <serge.hallyn@canonical.com> Cc: kernel-hardening@lists.openwall.com Cc: spender@grsecurity.net Link: http://lkml.kernel.org/r/20120319231253.GA20893@www.outflux.netSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Jesse Sung authored
commit c0190925 upstream. Add another vendor specific ID for BCM20702A0. output of usb-devices: T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a5c ProdID=21e3 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=9439E5CBF66C C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by:
Wen-chien Jesse Sung <jesse.sung@canonical.com> Acked-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by:
-
Cho, Yu-Chen authored
commit 07c0ea87 upstream. Add Atheros maryann 0cf3:311d PIDVID support This module is AR3012 Series. Include /sys/kernel/debug/usb/devices output here for reference before: T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=311d Rev= 0.01 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms after: T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=311d Rev= 0.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Cho, Yu-Chen <acho@suse.com> cked-by:
Johan Hedberg <johan.hedberg@intel.com> Cc: Jonathan Nieder <jrnieder@gmail.com> Signed-off-by:
-
Eran authored
commit 9498ba7a upstream. The bluetooth module in the Asus UX31/UX21 is based on Atheros AR3012 and requires a firmware to be uploaded before it's usable. output of usb-devices for this module: T: Bus=01 Lev=02 Prnt=02 Port=07 Cnt=03 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3375 Rev=00.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by:
Eran <eran@over-here.org> Tested-by:
Michal Labedzki <michal.labedzki@tieto.com> Signed-off-by:
-
Tomoya MORINAGA authored
commit 92b3a5c1 upstream. ML7831 is companion chip for Intel Atom E6xx series. Signed-off-by:
Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com> Signed-off-by:
Grant Likely <grant.likely@secretlab.ca> Signed-off-by:
Tomoya MORINAGA <tomoya.rohm@gmail.com> Signed-off-by:
-
Danny Kukawka authored
commit de3bd7e6 upstream. Fix for: drivers/spi/spi-topcliff-pch.c: In function ‘pch_spi_handler_sub’: drivers/spi/spi-topcliff-pch.c:325:17: warning: ‘bpw_len’ may be used uninitialized in this function [-Wuninitialized] drivers/spi/spi-topcliff-pch.c:325:42: warning: ‘rx_index’ may be used uninitialized in this function [-Wuninitialized] drivers/spi/spi-topcliff-pch.c:325:42: warning: ‘tx_index’ may be used uninitialized in this function [-Wuninitialized] Move usage of tx_index, rx_index and bpw_len into the same block as where they are set to prevent uninitialized usage. v2: instead of init variables with 0 move the whole block [This patch title "warnings" makes you think "This patch is not for bug fix". However, this patch surely patch for bug fix.] Signed-off-by:
Danny Kukawka <danny.kukawka@bisect.de> Signed-off-by:
-
Tomoya MORINAGA authored
commit ca7fe2db upstream. ML7831 is companion chip for Intel Atom E6xx series. Signed-off-by:
Vinod Koul <vinod.koul@linux.intel.com> Signed-off-by:
-
Dan Carpenter authored
commit 73f98eab upstream. pch_gbe_validate_option() modifies 32 bits of memory but we pass &hw->phy.autoneg_advertised which only has 16 bits and &hw->mac.fc which only has 8 bits. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Darren Hart authored
commit 2b53d078 upstream. If the MAC is invalid or not implemented, do not abort the probe. Issue a warning and prevent bringing the interface up until a MAC is set manually (via ifconfig $IFACE hw ether $MAC). Tested on two platforms, one with a valid MAC, the other without a MAC. The real MAC is used if present, the interface fails to come up until the MAC is set on the other. They successfully get an IP over DHCP and pass a simple ping and login over ssh test. This is meant to allow the Inforce SYS940X development board: http://www.inforcecomputing.com/SYS940X_ECX.html (and others suffering from a missing MAC) to work with the mainline kernel. Without this patch, the probe will fail and the interface will not be created, preventing the user from configuring the MAC manually. This does not make any attempt to address a missing or invalid MAC for the pch_phub driver. Signed-off-by:
Darren Hart <dvhart@linux.intel.com> CC: Arjan van de Ven <arjan@linux.intel.com> CC: Alan Cox <alan@linux.intel.com> CC: Tomoya MORINAGA <tomoya.rohm@gmail.com> CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: "David S. Miller" <davem@davemloft.net> CC: Paul Gortmaker <paul.gortmaker@windriver.com> CC: Jon Mason <jdmason@kudzu.us> CC: Mark Brown <broonie@opensource.wolfsonmicro.com> CC: David Laight <David.Laight@ACULAB.COM> CC: Joe Perches <joe@perches.com> Signed-off-by:
-
Jonghwan Choi authored
commit 51b79bee upstream. Add missing "personality.h" security/commoncap.c: In function 'cap_bprm_set_creds': security/commoncap.c:510: error: 'PER_CLEAR_ON_SETID' undeclared (first use in this function) security/commoncap.c:510: error: (Each undeclared identifier is reported only once security/commoncap.c:510: error: for each function it appears in.) Signed-off-by:
Jonghwan Choi <jhbird.choi@samsung.com> Acked-by:
Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by:
James Morris <james.l.morris@oracle.com> Cc: Eric Paris <eparis@redhat.com> Signed-off-by:
-
Lin Ming authored
commit 8931d9ea upstream. Allow referenced objects to be in a different scope. http://www.acpica.org/bugzilla/show_bug.cgi?id=937 http://marc.info/?l=linux-acpi&m=131636632718222&w=2 ACPI Error: [RAMB] Namespace lookup failure, AE_NOT_FOUND (20110112/psargs-359) ACPI Exception: AE_NOT_FOUND, Could not execute arguments for [RAMW] (Region) (20110112/nsinit-349) Scope (_SB) { Name (RAMB, 0xDF5A1018) OperationRegion (\RAMW, SystemMemory, RAMB, 0x00010000) } For above ASL code, we need to save scope node(\_SB) to lookup the argument node(\_SB.RAMB). Reported-by:
Jim Green <student.northwestern@gmail.com> Signed-off-by:
Lin Ming <ming.m.lin@intel.com> Signed-off-by:
Bob Moore <robert.moore@intel.com> Signed-off-by:
Len Brown <len.brown@intel.com> Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Signed-off-by:
-
Tomoya MORINAGA authored
commit 83331040 upstream. ISSUE: USB Suspend interrupts occur frequently. CAUSE: When it is called pch_udc_reconnect() in USB Suspend, it repeats reset and Suspend. SOLUTION: pch_udc_reconnect() does not enable all interrupts. When an enumeration event occurred the driver enables all interrupts. Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Tomoya MORINAGA authored
commit 1c575d2d upstream. ISSUE: After a USB cable is connect/disconnected, the system rarely freezes. CAUSE: Since the USB device controller cannot know to disconnect the USB cable, when it is used without detecting VBUS by GPIO, the UDC driver does not notify to USB Gadget. Since USB Gadget cannot know to disconnect, a false setting occurred when the USB cable is connected/disconnect repeatedly. Signed-off-by:
-
Tomoya MORINAGA authored
commit 84566abb upstream. ISSUE: After USB Suspend, a system rarely freezes. CAUSE: When USB Suspend occurred, the driver is not notifying a gadget of the event. Signed-off-by:
-
Tomoya MORINAGA authored
commit c802672c upstream. ISSUE: If the return value of pch_udc_pcd_init() is False, the return value of this function is unsettled. Since pch_udc_pcd_init() always returns 0, there is not actually the issue. CAUSE: If pch_udc_pcd_init() is True, the variable, retval, is not set for an appropriate value. Signed-off-by:
-
Tomoya MORINAGA authored
commit c50a3bff upstream. ISSUE: When the driver notifies a gadget of a disconnect event, a system rarely freezes. CAUSE: When the driver calls dev->driver->disconnect(), it is not calling spin_unlock(). Signed-off-by:
-
