Use genirq and provide seperated file for interrupts support.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The MAX8998 chip have regulator and rtc features. The i2c slave address
of regulator and rtc is different, so needs each i2c client on i2c
operation functions.

Also, this patch exports i2c operation functions instead of callback to
make easy to read.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

There is no reason to get irq twice.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

1. return -ENOMEM if platform_device_alloc() fail.
2. call platform_device_put() if platform_device_add() fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

1. return -ENOMEM if platform_device_alloc() fail.
2. call platform_device_put() if platform_device_add() fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch fixes da903x_add_subdevs error path:
1. return -ENOMEM if platform_device_alloc() fail.
2. call platform_device_put() if platform_device_add() fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add codec IRQ resources that are used in 88pm860x codec driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

For the resources allocated in tps6586x_i2c_probe(),
we need to free it in tps6586x_i2c_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

use the new definitions on twl header for code
consistency.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

use the new definitions on twl header for code
consistency.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

use the new definitions on twl header for code
consistency.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Some modules already need to talk to at least PROTECT_KEY
register, while at that, add defines to the entire register
space.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

LP3974 PMIC support. It has same functionality as max8998.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

GPIOs on these controller are multi-functional. If you decided to use
some of them e.g. as input channels for the ADC, you surely don't want
those pins to be reassigned as simple GPIOs (which may be triggered even
from userspace via 'export'). Same for the touchscreen controller pins.
Since knowledge about the hardware is needed to decide which GPIOs to
reserve, let this bitmask be inside platform_data and provide some
defines to assist potential users.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This switches the AB3100 core driver to using MFD cells for
subdevices instead of spawning common platform devices.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Since there is no discardable probe() function in the I2C device
framework, let's just tag it __devinit and take the footprint hit
rather than seeing the compilation warnings every day.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Not sure where this went.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Fixed warnings about unprototyped global functions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
  initramfs: Fix build break on symbol-prefixed archs
  initramfs: fix initramfs size calculation
  initramfs: generalize initramfs_data.xxx.S variants
  scripts/kallsyms: Enable error messages while hush up unnecessary warnings
  scripts/setlocalversion: update comment
  kbuild: Use a single clean rule for kernel and external modules
  kbuild: Do not run make clean in $(srctree)
  scripts/mod/modpost.c: fix commentary accordingly to last changes
  kbuild: Really don't clean bounds.h and asm-offsets.h

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: max8952 - fix max8952_set_voltage
  regulator: max8952 - fix max8952_pmic_probe error path
  regulator: fix build when CONFIG_REGULATOR_DUMMY=n
  regulator: avoid deadlock when disabling regulator with supply
  regulator: Add option for machine drivers to enable the dummy regulator
  Regulator: lp3972 cleanup
  Regulator: LP3972 PMIC regulator driver
  MAX8952 PMIC Driver Initial Release

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  nfs4: The difference of 2 pointers is ptrdiff_t
  nfs: testing the wrong variable
  nfs: handle lock context allocation failures in nfs_create_request
  Fixed Regression in NFS Direct I/O path

In current implementation, vid is declared as u8,
then "vid == -1" is always false, and "vid >= 0" is always true.
Thus change it to s8.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Commit f03f91826 (regulator: Add option for machine drivers
to enable the dummy regulator) in the regulators tree
seems to have introduced the following build break when
CONFIG_REGULATOR_DUMMY is disabled. Fix this.

  CC      drivers/regulator/dummy.o
drivers/regulator/dummy.c:41: error: redefinition of 'regulator_dummy_init'
drivers/regulator/dummy.h:28: note: previous definition of 'regulator_dummy_init' was here
make[2]: *** [drivers/regulator/dummy.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

I have a regulator A that sets regulator B as its supply. When I call
set_supply to add B as the supply for A, regulator A gets added to the
supply_list for regulator B.

When I call regulator_disable(A), I end up with a call chain like this:

regulator_disable(A)
> mutex_lock(A)
> _regulator_disable(A)
>> _regulator_disable(B)
>>> _notifier_call_chain(B)
>>>> mutex_lock(A)

Which results in dead lock since we are trying to acquire the mutex lock
for regulator A which we already hold.

This patch addresses this issue by moving the call to disable regulator
B outside of the lock aquired inside the initial call to
regulator_disable.

This change also addresses the issue of not acquiring the mutex for
regulator B before calling _regulator_disable(B).
Signed-off-by: Jeffrey Carlyle <jeff.carlyle@motorola.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Allow machine drivers to explicitly enable the use of the dummy regulator,
enabling simpler support for systems with only a few specific supplies
visible to software.

It is strongly recommended that this is not used on systems with
substantial software control over their PMICs, for maximum functionality
constrints should be as fully specified as possible.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This patch includes below fixes based on Mark's comment.
 - Return actual error if i2c_smbus_read_byte_data() fail
 - Add spaces around bitwise AND operator(&) to improve readability
 - Add comment to explain why we need to update voltage change control register
   for LDO1 and LDO5
 - Logging the value for diagnostics if chip reported incorrect voltage value
 - Add __devinit annotation for setup_regulators()
 - Show system control register1 value if the value is mismatched
 - Logging the value for diagnostics if failed to detect device
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

This patch adds regulator drivers for National Semiconductors LP3972 PMIC.
This LP3972 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out
(LDO) regulators. LP3972 PMIC controller uses I2C interface.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV
with DVS support. In this initial release, users can set voltages for
four DVS modes, RAMP delay values, and SYNC frequency.
Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID
is not supported in this release.

If GPIO of EN is not valid in platform data, the driver assumes that it
is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down
VID0 and VID1 to fix DVS mode as 0 and disables DVS support.

We assume that V_OUT is capable to provide every voltage from 770mV to
1.40V in 10mV steps although the data sheet has some ambiguity on it.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
v2:
	- Style correction
	- Can accept platform_data with invalid GPIOs
	- Removed unnecessary features
	- Improved error handling
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>

On m68k, which is 32-bit:

fs/nfs/nfs4proc.c: In function ‘nfs41_sequence_done’:
fs/nfs/nfs4proc.c:432: warning: format ‘%ld’ expects type ‘long int’, but argument 3 has type ‘int’
fs/nfs/nfs4proc.c: In function ‘nfs4_setup_sequence’:
fs/nfs/nfs4proc.c:576: warning: format ‘%ld’ expects type ‘long int’, but argument 5 has type ‘int’

On 32-bit, ptrdiff_t is int; on 64-bit, ptrdiff_t is long.

Introduced by commit dfb4f309 ("NFSv4.1: keep
seq_res.sr_slot as pointer rather than an index")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

Merge branch 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Move olpc to platform
  x86: Move uv to platform
  x86: Move mrst to platform
  x86: Move scx200 to platform
  x86: Move visws to platform
  x86: Move efi to platform
  x86: Move sfi to platform
  x86: Add platform directory

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (68 commits)
  hwmon: (it87) Add support for the IT8721F/IT8758E
  hwmon: (it87) Move conversion functions
  hwmon: Remove many EXPERIMENTAL flags
  hwmon: (lm85) Add support for ADT7468 high-frequency PWM mode
  hwmon: (lm85) Document the ADT7468 as supported
  hwmon: (lm85) Fix ADT7468 frequency table
  hwmon: I2C addresses are constant
  Move ams driver to macintosh
  hwmon: (pcf8591) Don't attempt to detect devices
  hwmon: (pcf8591) Register as a hwmon device
  hwmon: (w83795) Use standard attributes for chassis intrusion
  hwmon: (w83795) Exclude fan control feature by default
  hwmon: (w83795) Add myself as co-author and maintainer
  hwmon: (w83795) More style cleanups
  hwmon: (w83795) Fix LSB reading of voltage limits
  hwmon: (w83795) Use dev_get_drvdata() where possible
  hwmon: (w83795) Delay reading pwm config registers
  hwmon: (w83795) Delay reading limit registers
  hwmon: (w83795) Move register reads to dedicated functions
  hwmon: (w83795) Pack similar register reads
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (841 commits)
  Staging: brcm80211: fix usage of roundup in structures
  Staging: bcm: fix up network device reference counting
  Staging: keucr: fix up US_ macro change
  staging: brcm80211: brcmfmac: Removed codeversion from firmware filenames.
  staging: brcm80211: Remove unnecessary header files.
  staging: brcm80211: Remove unnecessary includes from bcmutils.c
  staging: brcm80211: Removed unnecessary pktsetprio() function.
  Staging: brcm80211: remove typedefs.h
  Staging: brcm80211: remove uintptr typedef usage
  Staging: hv: remove struct vmbus_channel_interface
  Staging: hv: remove Open from struct vmbus_channel_interface
  Staging: hv: storvsc: call vmbus_open directly
  Staging: hv: netvsc: call vmbus_open directly
  Staging: hv: channel: export vmbus_open to modules
  Staging: hv: remove Close from struct vmbus_channel_interface
  Staging: hv: netvsc: call vmbus_close directly
  Staging: hv: storvsc: call vmbus_close directly
  Staging: hv: channel: export vmbus_close to modules
  Staging: hv: remove SendPacket from struct vmbus_channel_interface
  Staging: hv: storvsc: call vmbus_sendpacket directly
  ...

Fix up conflicts in
	drivers/staging/cx25821/cx25821-audio-upstream.c
	drivers/staging/cx25821/cx25821-audio.h
due to warring whitespace cleanups (neither of which were all that great)

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (32 commits)
  sh: intc: switch irq_desc iteration to new active IRQ iterator.
  sh: fix up cpu hotplug IRQ migration for irq_data changes.
  sh: oprofile: Make sure the backtrace op is available for timer-fallback.
  sh64: oprofile: Fix up kernel stack pointer size mismatch.
  sh: oprofile: Fix up and extend op_name_from_perf_id().
  sh: lockless get_user_pages_fast()
  sh64: _PAGE_SPECIAL support.
  sound: sh: ctrl_in/outX to __raw_read/writeX conversion.
  sh: disable deprecated genirq support.
  sh: update show_interrupts() for irq_data chip lookup.
  sh: intc: irq_data conversion.
  sh64: irq_data conversion.
  sh64: update for IRQ flag handling naming changes.
  rtc: rtc-rs5c313: ctrl_in/outX to __raw_read/writeX conversion.
  sh: mach-se: irq_data conversion.
  input: hp680_ts_input: ctrl_in/outX to __raw_read/writeX conversion.
  input: jornada680_kbd: ctrl_in/outX to __raw_read/writeX conversion.
  sh: hd64461: irq_data conversion.
  sh: mach-x3proto: irq_data conversion.
  sh: mach-systemh: irq_data conversion.
  ...

* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
  x86: allocate space within a region top-down
  x86: update iomem_resource end based on CPU physical address capabilities
  x86/PCI: allocate space from the end of a region, not the beginning
  PCI: allocate bus resources from the top down
  resources: support allocating space within a region from the top down
  resources: handle overflow when aligning start of available area
  resources: ensure callback doesn't allocate outside available space
  resources: factor out resource_clip() to simplify find_resource()
  resources: add a default alignf to simplify find_resource()
  x86/PCI: MMCONFIG: fix region end calculation
  PCI: Add support for polling PME state on suspended legacy PCI devices
  PCI: Export some PCI PM functionality
  PCI: fix message typo
  PCI: log vendor/device ID always
  PCI: update Intel chipset names and defines
  PCI: use new ccflags variable in Makefile
  PCI: add PCI_MSIX_TABLE/PBA defines
  PCI: add PCI vendor id for STmicroelectronics
  x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
  PCI: OLPC: Only enable PCI configuration type override on XO-1
  ...

Add support for the IT8721F/IT8758E. These new chips differ from the
older IT87xxF chips in the following ways:
* ADC LSB is 12 mV instead of 16 mV.
* PWM values are 8-bit instead of 7-bit.
There are other minor changes we don't have to care about in the
driver.

Another change is that we will handle internal voltage scaling in the
driver instead of delegating the work to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Move conversion functions until after structure defintions. This is
needed for future changes which make use of the structures in the
conversion funtcions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Remove the dependency on EXPERIMENTAL for all drivers which are in
the kernel tree for a long time, are known to work properly and for
which we have documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

The ADT7468 supports a high-frequency PWM output mode where all PWM
outputs are driven by a 22.5 kHz clock. Add support for this mode, and
document it, as it may surprise the user that setting one PWM output
frequency also affects the other PWM outputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>