The type of arg passed to dmatest_callback is struct dmatest_done.
It refers to test_done in struct dmatest_thread, not done_wait.

Fixes: 6f6a23a2 ("dmaengine: dmatest: move callback wait ...")
Signed-off-by: Yang Shunyong <shunyong.yang@hxt-semitech.com>
Acked-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The hidma driver open codes populating address and IRQ resources from DT.
We have standard functions of_address_to_resource and of_irq_to_resource
for this, so use them instead.

The DT binding states each child should have 2 addresses and 1 IRQ, so we
can simplify the logic and do a fixed size resource allocation. Using the
standard of_address_to_resource will also do any address translation which
was missing.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Monospace is more readable and is also used elsewhere in the docs.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The bullet list documenting the 'struct dma_device' fields has several
nesting errors, making it render improperly. It also has incoherent
formatting: some fields have a description in the same bullet, some in
a sub-bullet.

Fix both to have a correct and coherent formatting.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The test should be >= ARRAY_SIZE() instead of > ARRAY_SIZE().
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This avoid the following error when using an initramfs on wandboard quad
Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Previously enabled clks are only disabled if clk_prepare_enable() fails.
However, there are other error paths were the previously enabled
clocks are not disabled.

To fix the problem, fsl_disable_clocks() now takes the number of clocks
that shall be disabled + unprepared. For existing calls were all clocks
were already successfully prepared + enabled, DMAMUX_NR is passed to
disable + unprepare all clocks.

In error paths were only some clocks were successfully prepared +
enabled the loop counter is passed, in order to disable + unprepare
all successfully prepared + enabled clocks.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Andreas Platschek <andreas.platschek@opentech.at>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The location for destination event channel register has been relocated from
offset 0x28 to 0x40. Update the code accordingly.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Add support for probing the newer HW and also organize MSI capable hardware
into an array for maintenance reasons.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

A new version of the HIDMA IP has been released with bug fixes. Bumping the
hardware version to differentiate from others.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Now that we have a get_match_data() callback as part of the firmware node,
implement the ACPI specific piece for it.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Now that we have a get_match_data() callback as part of the firmware node,
implement the OF specific piece for it.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

There is an OF/ACPI function to obtain the driver data. We want to hide
OF/ACPI details from the device drivers and abstract following the device
family of functions.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

OF has of_device_get_match_data() function to extract driver specific data
structure. Add a similar function for ACPI.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Driver is missing the interrupts if two requests are queued up at the same
time as the interrupt handler is servicing a request that was just
delivered.

The ISR clears the interrupt at the end but it could be clearing the
interrupt for an outstanding event. Therefore, second interrupt never
arrives.

Clear the interrupt first and then check for completions.

Also, make sure that request start and interrupt clear do not overlap in
time by using a spinlock.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

in error path of jz4740_dma_probe(), call clk_disable_unprepare() to clean
up.

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 25ce6c35 MIPS: jz4740: Remove custom DMA API
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Commit adfa543e ("dmatest: don't use set_freezable_with_signal()")
introduced a bug (that is in fact documented by the patch commit text)
that leaves behind a dangling pointer. Since the done_wait structure is
allocated on the stack, future invocations to the DMATEST can produce
undesirable results (e.g., corrupted spinlocks).

Commit a9df21e3 ("dmaengine: dmatest: warn user when dma test times
out") attempted to WARN the user that the stack was likely corrupted but
did not fix the actual issue.

This patch fixes the issue by pushing the wait queue and callback
structs into the the thread structure. If a failure occurs due to time,
dmaengine_terminate_all will force the callback to safely call
wake_up_all() without possibility of using a freed pointer.

Cc: stable@vger.kernel.org
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=197605
Fixes: adfa543e ("dmatest: don't use set_freezable_with_signal()")
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Suggested-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Fix ptr_ret.cocci warnings:
drivers/dma/mic_x100_dma.c:483:1-3: WARNING: PTR_ERR_OR_ZERO can be used

Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

_xt_ is being dereferenced before it is null checked, hence there is a
potential null pointer dereference.

Fix this by moving the pointer dereference after _xt_ has been null
checked.

This issue was detected with the help of Coccinelle.

Fixes: 4483320e ("dmaengine: Use Pointer xt after NULL check.")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

If the last test in 'ioat_dma_self_test()' fails, we must release all
the allocated resources and not just part of them.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Pull ARM fixes from Russell King:

 - LPAE fixes for kernel-readonly regions

 - Fix for get_user_pages_fast on LPAE systems

 - avoid tying decompressor to a particular platform if DEBUG_LL is
   enabled

 - BUG if we attempt to return to userspace but the to-be-restored PSR
   value keeps us in privileged mode (defeating an issue that ftracetest
   found)

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: BUG if jumping to usermode address in kernel mode
  ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
  ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
  ARM: make decompressor debug output user selectable
  ARM: fix get_user_pages_fast

Pull irq fixes from Thomas Glexiner:

 - unbreak the irq trigger type check for legacy platforms

 - a handful fixes for ARM GIC v3/4 interrupt controllers

 - a few trivial fixes all over the place

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/matrix: Make - vs ?: Precedence explicit
  irqchip/imgpdc: Use resource_size function on resource object
  irqchip/qcom: Fix u32 comparison with value less than zero
  irqchip/exiu: Fix return value check in exiu_init()
  irqchip/gic-v3-its: Remove artificial dependency on PCI
  irqchip/gic-v4: Add forward definition of struct irq_domain_ops
  irqchip/gic-v3: pr_err() strings should end with newlines
  irqchip/s3c24xx: pr_err() strings should end with newlines
  irqchip/gic-v3: Fix ppi-partitions lookup
  irqchip/gic-v4: Clear IRQ_DISABLE_UNLAZY again if mapping fails
  genirq: Track whether the trigger type has been set

Pull misc x86 fixes from Ingo Molnar:
 - topology enumeration fixes
 - KASAN fix
 - two entry fixes (not yet the big series related to KASLR)
 - remove obsolete code
 - instruction decoder fix
 - better /dev/mem sanity checks, hopefully working better this time
 - pkeys fixes
 - two ACPI fixes
 - 5-level paging related fixes
 - UMIP fixes that should make application visible faults more debuggable
 - boot fix for weird virtualization environment

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
  x86/decoder: Add new TEST instruction pattern
  x86/PCI: Remove unused HyperTransport interrupt support
  x86/umip: Fix insn_get_code_seg_params()'s return value
  x86/boot/KASLR: Remove unused variable
  x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
  x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
  x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
  x86/pkeys/selftests: Fix protection keys write() warning
  x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
  x86/mpx/selftests: Fix up weird arrays
  x86/pkeys: Update documentation about availability
  x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
  x86/smpboot: Fix __max_logical_packages estimate
  x86/topology: Avoid wasting 128k for package id array
  perf/x86/intel/uncore: Cache logical pkg id in uncore driver
  x86/acpi: Reduce code duplication in mp_override_legacy_irq()
  x86/acpi: Handle SCI interrupts above legacy space gracefully
  x86/boot: Fix boot failure when SMP MP-table is based at 0
  x86/mm: Limit mmap() of /dev/mem to valid physical addresses
  x86/selftests: Add test for mapping placement for 5-level paging
  ...

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes: a documentation fix, a Sparse warning fix and a debugging
  fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/debug: Fix task state recording/printout
  sched/deadline: Don't use dubious signed bitfields
  sched/deadline: Fix the description of runtime accounting in the documentation

Pull perf fixes from Ingo Molnar:
 "Misc fixes: two PMU driver fixes and a memory leak fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix memory leak triggered by perf --namespace
  perf/x86/intel/uncore: Add event constraint for BDX PCU
  perf/x86/intel: Hide TSX events when RTM is not supported

Pull static key fix from Ingo Molnar:
 "Fix a boot warning related to bad init ordering of the static keys
  self-test"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  jump_label: Invoke jump_label_test() via early_initcall()

Pull objtool fixes from Ingo Molnar:
 "A handful of objtool fixes, most of them related to making the UAPI
  header-syncing warnings easier to read and easier to act upon"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/headers: Sync objtool UAPI header
  objtool: Fix cross-build
  objtool: Move kernel headers/code sync check to a script
  objtool: Move synced files to their original relative locations
  objtool: Make unreachable annotation inline asms explicitly volatile
  objtool: Add a comment for the unreachable annotation macros

Detect if we are returning to usermode via the normal kernel exit paths
but the saved PSR value indicates that we are in kernel mode.  This
could occur due to corrupted stack state, which has been observed with
"ftracetest".

This ensures that we catch the problem case before we get to user code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Pull timer updates from Thomas Gleixner:

 - The final conversion of timer wheel timers to timer_setup().

   A few manual conversions and a large coccinelle assisted sweep and
   the removal of the old initialization mechanisms and the related
   code.

 - Remove the now unused VSYSCALL update code

 - Fix permissions of /proc/timer_list. I still need to get rid of that
   file completely

 - Rename a misnomed clocksource function and remove a stale declaration

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
  m68k/macboing: Fix missed timer callback assignment
  treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
  timer: Remove redundant __setup_timer*() macros
  timer: Pass function down to initialization routines
  timer: Remove unused data arguments from macros
  timer: Switch callback prototype to take struct timer_list * argument
  timer: Pass timer_list pointer to callbacks unconditionally
  Coccinelle: Remove setup_timer.cocci
  timer: Remove setup_*timer() interface
  timer: Remove init_timer() interface
  treewide: setup_timer() -> timer_setup() (2 field)
  treewide: setup_timer() -> timer_setup()
  treewide: init_timer() -> setup_timer()
  treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
  s390: cmm: Convert timers to use timer_setup()
  lightnvm: Convert timers to use timer_setup()
  drivers/net: cris: Convert timers to use timer_setup()
  drm/vc4: Convert timers to use timer_setup()
  block/laptop_mode: Convert timers to use timer_setup()
  net/atm/mpc: Avoid open-coded assignment of timer callback function
  ...

Pull ARC updates from Vineet Gupta:

 - more changes for HS48 cores: supporting MMUv5, detecting new
   micro-arch gizmos

 - axs10x platform wiring up reset driver merged in this cycle

 - ARC perf driver optimizations

* tag 'arc-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: perf: avoid vmalloc backed mmap
  ARCv2: perf: optimize given that num counters <= 32
  ARCv2: perf: tweak overflow interrupt
  ARC: [plat-axs10x] DTS: Add reset controller node to manage ethernet reset
  ARCv2: boot log: updates for HS48: dual-issue, ECC, Loop Buffer
  ARCv2: Accomodate HS48 MMUv5 by relaxing MMU ver checking
  ARC: [plat-axs10x] auto-select AXS101 or AXS103 given the  ISA config

Pull more Kbuild updates from Masahiro Yamada:

 - use 'pwd' instead of '/bin/pwd' for portability

 - clean up Makefiles

 - fix ld-option for clang

 - fix malloc'ed data size in Kconfig

 - fix parallel building along with coccicheck

 - fix a minor issue of package building

 - prompt to use "rpm-pkg" instead of "rpm"

 - clean up *.i and *.lst patterns by "make clean"

* tag 'kbuild-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: drop $(extra-y) from real-objs-y
  kbuild: clean up *.i and *.lst patterns by make clean
  kbuild: rpm: prompt to use "rpm-pkg" if "rpm" target is used
  kbuild: pkg: use --transform option to prefix paths in tar
  coccinelle: fix parallel build with CHECK=scripts/coccicheck
  kconfig/symbol.c: use correct pointer type argument for sizeof
  kbuild: Set KBUILD_CFLAGS before incl. arch Makefile
  kbuild: remove all dummy assignments to obj-
  kbuild: create built-in.o automatically if parent directory wants it
  kbuild: /bin/pwd -> pwd