- 07 Jun, 2011 1 commit
-
-
Frederic Weisbecker authored
It's really supposed to be defined here. If it's not then we actually want the build to crash so that we know it, and not keep it silent. Signed-off-by:Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
-
- 03 Jun, 2011 1 commit
-
-
Ingo Molnar authored
Merge branch 'unlikely/sched' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-trace into sched/urgent
-
- 31 May, 2011 2 commits
-
-
Peter Zijlstra authored
While looking over the code I found that with the ttwu rework the nr_wakeups_migrate test broke since we now switch cpus prior to calling ttwu_stat(), hence the test is always true. Cure this by passing the migration state in wake_flags. Also move the whole test under CONFIG_SMP, its hard to migrate tasks on UP :-) Signed-off-by:
Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/n/tip-pwwxl7gdqs5676f1d4cx6pj7@git.kernel.orgSigned-off-by:
Ingo Molnar <mingo@elte.hu>
-
Peter Zijlstra authored
Markus reported that commit 317f3941 ("sched: Move the second half of ttwu() to the remote cpu") caused some accounting funnies on his AMD Phenom II X4, such as weird 'top' results. It turns out that this is due to non-synced TSC and the queued remote wakeups stopped coupeling the two relevant cpu clocks, which leads to wakeups seeing time jumps, which in turn lead to skewed runtime stats. Add an explicit call to sched_clock_cpu() to couple the per-cpu clocks to restore the normal flow of time. Reported-and-tested-by:
Markus Trippelsdorf <markus@trippelsdorf.de> Signed-off-by:
-
- 28 May, 2011 4 commits
-
-
KOSAKI Motohiro authored
The rule is, we have to update tsk->rt.nr_cpus_allowed if we change tsk->cpus_allowed. Otherwise RT scheduler may confuse. Signed-off-by:
KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by:
-
Peter Zijlstra authored
Dima Zavin <dima@android.com> reported: "After pulling the thread off the run-queue during a cgroup change, the cfs_rq.min_vruntime gets recalculated. The dequeued thread's vruntime then gets normalized to this new value. This can then lead to the thread getting an unfair boost in the new group if the vruntime of the next task in the old run-queue was way further ahead." Reported-by:
Dima Zavin <dima@android.com> Signed-off-by:
John Stultz <john.stultz@linaro.org> Recalls-having-tested-once-upon-a-time-by:
Mike Galbraith <efault@gmx.de> Signed-off-by:
-
Peter Zijlstra authored
Marc reported that e4a52bcb (sched: Remove rq->lock from the first half of ttwu()) broke his ARM-SMP machine. Now ARM is one of the few __ARCH_WANT_INTERRUPTS_ON_CTXSW users, so that exception in the ttwu() code was suspect. Yong found that the interrupt could hit after context_switch() changes current but before it clears p->on_cpu, if that interrupt were to attempt a wake-up of p we would indeed find ourselves spinning in IRQ context. Fix this by reverting to the old behaviour for this situation and perform a full remote wake-up. Cc: Frank Rowand <frank.rowand@am.sony.com> Cc: Yong Zhang <yong.zhang0@gmail.com> Cc: Oleg Nesterov <oleg@redhat.com> Reported-by:
Marc Zyngier <Marc.Zyngier@arm.com> Tested-by:
-
Xiaotian Feng authored
sched_domain iterations needs to be protected by rcu_read_lock() now, this patch adds another two places which needs the rcu lock, which is spotted by following suspicious rcu_dereference_check() usage warnings. kernel/sched_rt.c:1244 invoked rcu_dereference_check() without protection! kernel/sched_stats.h:41 invoked rcu_dereference_check() without protection! Signed-off-by:
Xiaotian Feng <dfeng@redhat.com> Signed-off-by:
-
- 27 May, 2011 32 commits
-
-
Linus Torvalds authored
Merge branch 'upstream/tidy-xen-mmu-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen * 'upstream/tidy-xen-mmu-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen: xen: fix compile without CONFIG_XEN_DEBUG_FS Use arbitrary_virt_to_machine() to deal with ioremapped pud updates. Use arbitrary_virt_to_machine() to deal with ioremapped pmd updates. xen/mmu: remove all ad-hoc stats stuff xen: use normal virt_to_machine for ptes xen: make a pile of mmu pvop functions static vmalloc: remove vmalloc_sync_all() from alloc_vm_area() xen: condense everything onto xen_set_pte xen: use mmu_update for xen_set_pte_at() xen: drop all the special iomap pte paths.
-
Linus Torvalds authored
Right now security_get_user_sids() will pass in a NULL avd pointer to avc_has_perm_noaudit(), which then forces that function to have a dummy entry for that case and just generally test it. Don't do it. The normal callers all pass a real avd pointer, and this helper function is incredibly hot. So don't make avc_has_perm_noaudit() do conditional stuff that isn't needed for the common case. This also avoids some duplicated stack space. Signed-off-by:Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/pkl/squashfs-linusLinus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/pkl/squashfs-linus: Squashfs: update email address Squashfs: add extra sanity checks at mount time Squashfs: add sanity checks to fragment reading at mount time Squashfs: add sanity checks to lookup table reading at mount time Squashfs: add sanity checks to id reading at mount time Squashfs: add sanity checks to xattr reading at mount time Squashfs: reverse order of filesystem table reading Squashfs: move table allocation into squashfs_read_table()
-
Akinobu Mita authored
The implementation of find_next_bit_le() on m68knommu is identical with the generic implementation of find_next_bit_le(). Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Cc: Greg Ungerer <gerg@uclinux.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Akinobu Mita authored
The previous style change enables to use asm-generic/bitops/le.h on s390. Signed-off-by:
-
Akinobu Mita authored
The previous style change enables to use asm-generic/bitops/le.h on arm. Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Greg Ungerer <gerg@uclinux.org> Signed-off-by:
-
Akinobu Mita authored
By the previous style change, CONFIG_GENERIC_FIND_NEXT_BIT, CONFIG_GENERIC_FIND_BIT_LE, and CONFIG_GENERIC_FIND_LAST_BIT are not used to test for existence of find bitops anymore. Signed-off-by:
Greg Ungerer <gerg@uclinux.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
-
Akinobu Mita authored
The style that we normally use in asm-generic is to test the macro itself for existence, so in asm-generic, do: #ifndef find_next_zero_bit_le extern unsigned long find_next_zero_bit_le(const void *addr, unsigned long size, unsigned long offset); #endif and in the architectures, write static inline unsigned long find_next_zero_bit_le(const void *addr, unsigned long size, unsigned long offset) #define find_next_zero_bit_le find_next_zero_bit_le This adds the #ifndef for each of the find bitops in the generic header and source files. Suggested-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Akinobu Mita authored
The style that we normally use in asm-generic is to test the macro itself for existence, so in asm-generic, do: #ifndef find_next_zero_bit_le extern unsigned long find_next_zero_bit_le(const void *addr, unsigned long size, unsigned long offset); #endif and in the architectures, write static inline unsigned long find_next_zero_bit_le(const void *addr, unsigned long size, unsigned long offset) #define find_next_zero_bit_le find_next_zero_bit_le This adds the #define for each of the optimized find bitops in the architectures. Suggested-by:
Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Acked-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Akinobu Mita authored
m68knommu can't build ext4, udf, and ocfs2 due to the lack of find_next_bit_le(). This implements find_next_bit_le() on m68knommu by duplicating the generic find_next_bit_le() in lib/find_next_bit.c. Signed-off-by:
-
Clifton Barnes authored
Add support for the Maxim/Dallas DS2780 Stand-Alone Fuel Gauge IC. It was suggested to combine this functionality with the current ds2782 driver. Unfortunately, I'm unable to commit the time to refactoring this driver to that extent and I don't have a platform with the ds2782 part to validate that there are no regression issues by adding this functionality. [akpm@linux-foundation.org: use min_t()] Signed-off-by:
Clifton Barnes <cabarnes@indesign-llc.com> Tested-by:
Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Cc: Ryan Mallon <ryan@bluewatersys.com> Signed-off-by:
-
David Fries authored
Reorganize so the netlink connector one wire search command will update the kernel list of detected slave devices. Otherwise, a newly detected device is unusable because unless it's in the kernel list of known devices any commands will result in ENODEV status. Signed-off-by:
David Fries <David@Fries.net> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by:
-
Jean-François Dagenais authored
This adds multi-slave support of the w1 bus for the ds1wm Synthesizable 1-Wire Bus Master. Also many fixes and tweaks based on the rev3 of the datasheet http://datasheets.maxim-ic.com/en/ds/DS1WM.pdfSigned-off-by:
Jean-François Dagenais <dagenaisj@sonatest.com> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu> Cc: Matt Reimer <mreimer@vpop.net> Signed-off-by:
-
Jean-François Dagenais authored
This DS2408 w1 slave driver is not complete for all the features of the chip, but its sufficient if you use it as a simple IO expander. [randy.dunlap@oracle.com: fix w1_ds2408.c printk formats] Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Jean-François Dagenais authored
The first patch adds generic functionnality to w1_io for Resume Command [A5h] lots of slaves support. I found it useful for multi-commands/reset workflows with the same slave on a multi-slave bus. This DS2408 w1 slave driver is not complete for all the features of the chip, but its sufficient if you use it as a simple IO expander. Enjoy! The ds1wm had Kconfig dependencies towards ARM && HAVE_CLK. I took them out since I was using the ds1wm on an x86_64 platform (ds1wm in a FPGA through pcie) and found them irrelevant. The clock freq/divisors at the top of ds1wm.c did not have the MSB set to 1. This bit is CLK_EN which turns the whole prescaler and dividers on. The driver never mentionned this bit either, so I just included this bit right in the table entries. I also took the liberty to add a couple of entries to the table. The spec doesn't explicitely mentions these possibilities but the description and examination of the core shows the prescalers & dividers can be used for more than the table explicitely shows. The table I enlarged still doesn't cover all possibilities, but it's a good start. I also made a few tweaks to a couple of the read and write algorithms which made sense while I had my head very deep in the ds1wm documentation. We stressed it a lot with 10+ slaves on the bus, many ds2408, ds2431 and ds2433 at the same time doing extensive interaction. It proved quite stable in our production environment. This patch: Add generic functionnality to w1_io for Resume Command [A5h] lots of slaves support. Signed-off-by:
-
Rakib Mullick authored
profile_hits() has a common check for prof_on and prof_buffer regardless of SMP or !SMP. So, remove some duplicate code by splitting profile_hits into two. [akpm@linux-foundation.org: make do_profile_hits static] Signed-off-by:
Rakib Mullick <rakib.mullick@gmail.com> Signed-off-by:
-
Julia Lawall authored
parport_find_number() calls parport_get_port() on its result, so there should be a corresponding call to parport_put_port() before dropping the reference. Similar code is found in the function register_device() in the same file. The semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @exists@ local idexpression struct parport * x; expression ra,rr; statement S1,S2; @@ x = parport_find_number(...) ... when != x = rr when any when != parport_put_port(x,...) when != if (...) { ... parport_put_port(x,...) ...} ( if(<+...x...+>) S1 else S2 | if(...) { ... when != x = ra when forall when != parport_put_port(x,...) *return...; } ) // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Lai Jiangshan authored
synchronize_rcu() does the stuff as needed. Signed-off-by:
Lai Jiangshan <laijs@cn.fujitsu.com> Cc: Doug Thompson <dougthompson@xmission.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Signed-off-by:
-
Sisir Koppaka authored
finds is misspelt as finr. No functional change. Signed-off-by:
Sisir Koppaka <sisir.koppaka@gmail.com> Signed-off-by:
-
Timo Warns authored
The kernel automatically evaluates partition tables of storage devices. The code for evaluating GUID partitions (in fs/partitions/efi.c) contains a bug that causes a kernel oops on certain corrupted GUID partition tables. This bug has security impacts, because it allows, for example, to prepare a storage device that crashes a kernel subsystem upon connecting the device (e.g., a "USB Stick of (Partial) Death"). crc = efi_crc32((const unsigned char *) (*gpt), le32_to_cpu((*gpt)->header_size)); computes a CRC32 checksum over gpt covering (*gpt)->header_size bytes. There is no validation of (*gpt)->header_size before the efi_crc32 call. A corrupted partition table may have large values for (*gpt)->header_size. In this case, the CRC32 computation access memory beyond the memory allocated for gpt, which may cause a kernel heap overflow. Validate value of GUID partition table header size. [akpm@linux-foundation.org: fix layout and indenting] Signed-off-by:
Timo Warns <warns@pre-sense.de> Cc: Matt Domsch <Matt_Domsch@dell.com> Cc: Eugene Teo <eugeneteo@kernel.sg> Cc: Dave Jones <davej@codemonkey.org.uk> Signed-off-by:
-
Rakib Mullick authored
Let memory allocator initialize the allocated memory as null, thus remove the use of memset. Signed-off-by:
-
Alexey Dobriyan authored
The ->read_proc interface is going away, convert to seq_file. Signed-off-by:
Alexey Dobriyan <adobriyan@gmail.com> Cc:Corey Minyard <minyard@acm.org> Signed-off-by:
-
Olaf Hering authored
The balloon driver in a Xen guest frees guest pages and marks them as mmio. When the kernel crashes and the crash kernel attempts to read the oldmem via /proc/vmcore a read from ballooned pages will generate 100% load in dom0 because Xen asks qemu-dm for the page content. Since the reads come in as 8byte requests each ballooned page is tried 512 times. With this change a hook can be registered which checks wether the given pfn is really ram. The hook has to return a value > 0 for ram pages, a value < 0 on error (because the hypercall is not known) and 0 for non-ram pages. This will reduce the time to read /proc/vmcore. Without this change a 512M guest with 128M crashkernel region needs 200 seconds to read it, with this change it takes just 2 seconds. Signed-off-by:
Olaf Hering <olaf@aepfle.de> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by:
-
KOSAKI Motohiro authored
Currently, pagemap_read() has three error and/or corner case handling mistake. (1) If ppos parameter is wrong, mm refcount will be leak. (2) If count parameter is 0, mm refcount will be leak too. (3) If the current task is sleeping in kmalloc() and the system is out of memory and oom-killer kill the proc associated task, mm_refcount prevent the task free its memory. then system may hang up. <Quote Hugh's explain why we shold call kmalloc() before get_mm()> check_mem_permission gets a reference to the mm. If we __get_free_page after check_mem_permission, imagine what happens if the system is out of memory, and the mm we're looking at is selected for killing by the OOM killer: while we wait in __get_free_page for more memory, no memory is freed from the selected mm because it cannot reach exit_mmap while we hold that reference. This patch fixes the above three. Signed-off-by:Hugh Dickins <hughd@google.com> Cc: Stephen Wilson <wilsons@start.ca> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by:
-
KOSAKI Motohiro authored
It whould be better if put check_mem_permission after __get_free_page in mem_write, to be same as function mem_read. Hugh Dickins explained the reason. check_mem_permission gets a reference to the mm. If we __get_free_page after check_mem_permission, imagine what happens if the system is out of memory, and the mm we're looking at is selected for killing by the OOM killer: while we wait in __get_free_page for more memory, no memory is freed from the selected mm because it cannot reach exit_mmap while we hold that reference. Reported-by:Jovi Zhang <bookjovi@gmail.com> Signed-off-by:
Stephen Wilson <wilsons@start.ca> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by:
-
Yuanhan Liu authored
There is a macro for the max size kmalloc can allocate, so use it instead of a hardcoded number. Signed-off-by:
Yuanhan Liu <yuanhan.liu@linux.intel.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by:
-
Mike Frysinger authored
No need for this local array to be writable, so mark it const. Signed-off-by:
Mike Frysinger <vapier@gentoo.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by:
-
Alexey Dobriyan authored
Convert fs/proc/ from strict_strto*() to kstrto*() functions. Signed-off-by:
-
Jiri Slaby authored
Now, exe_file is not proc FS dependent, so we can use it to name core file. So we add %E pattern for core file name cration which extract path from mm_struct->exe_file. Then it converts slashes to exclamation marks and pastes the result to the core file name itself. This is useful for environments where binary names are longer than 16 character (the current->comm limitation). Also where there are binaries with same name but in a different path. Further in case the binery itself changes its current->comm after exec. So by doing (s/$/#/ -- # is treated as git comment): $ sysctl kernel.core_pattern='core.%p.%e.%E' $ ln /bin/cat cat45678901234567890 $ ./cat45678901234567890 ^Z $ rm cat45678901234567890 $ fg ^\Quit (core dumped) $ ls core* we now get: core.2434.cat456789012345.!root!cat45678901234567890 (deleted) Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Reviewed-by:
Andi Kleen <andi@firstfloor.org> Signed-off-by:
-
Jiri Slaby authored
Setup and cleanup of mm_struct->exe_file is currently done in fs/proc/. This was because exe_file was needed only for /proc/<pid>/exe. Since we will need the exe_file functionality also for core dumps (so core name can contain full binary path), built this functionality always into the kernel. To achieve that move that out of proc FS to the kernel/ where in fact it should belong. By doing that we can make dup_mm_exe_file static. Also we can drop linux/proc_fs.h inclusion in fs/exec.c and kernel/fork.c. Signed-off-by:
-
Mike Frysinger authored
The Blackfin arch, like the x86 arch, needs to adjust the PC manually after a breakpoint is hit as normally this is handled by the remote gdb. However, rather than starting another arch ifdef mess, create a common GDB_ADJUSTS_BREAK_OFFSET define for any arch to opt-in via their kgdb.h. Signed-off-by:
Paul Mundt <lethal@linux-sh.org> Acked-by:
Dongdong Deng <dongdong.deng@windriver.com> Cc: Sergei Shtylyov <sshtylyov@mvista.com> Signed-off-by:
-
Mike Frysinger authored
Signed-off-by:
-
