Tweak the Feroceon match/mask in arch/arm/boot/compressed/head.S to
match a couple of newer Feroceon cores (such as the 88fr571vd with
CPU ID 0x56155710, and the 88fr131 with CPU ID 0x56251310) as well.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Flushing the L1 D cache with a test/clean/invalidate loop is very
easy in software, but it is not the quickest way of doing it, as
there is a lot of overhead involved in re-scanning the cache from
the beginning every time we hit a dirty line.

This patch makes proc-feroceon.S use "clean+invalidate by set/way"
loops according to possible cache configuration of Feroceon CPUs
(either direct-mapped or 4-way set associative).
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Nuke the Orion-specific orion5x_{read,write} wrappers.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

This patch adds support for the Maxtor Shared Storage II hardware.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Tested-by: Peter van Valderen <p.v.valderen@gmail.com>

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

This patch implements the communication with the microcontroller on the
Kurobox Pro and Linkstation Pro/Live boards.  This is allowing to send
the commands needed to power-off the board correctly.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

The mv643xx_eth platform data field ->force_phy_addr only needs
to be set if the passed-in ->phy_addr field is zero (to distinguish
the case of not having specified a phy address
(force_phy_addr = 0) from the case where a phy address of zero needs
to be used (force_phy_addr = 1.))

Also, the ->force_phy_addr field will hopefully disappear in a
future mv643xx_eth reorganisation.

Therefore, this patch deletes the ->force_phy_addr field initialiser
from all Orion board code.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

If all PCI devices are working as expected, the error printks in the
various implementations of ->map_irq() doesn't really provide any
useful info.  And if something is not working as expected, turning
on pci=debug gives you more useful information than the printk calls
in ->map_irq(), since the former also tells you which devices _did_
get IRQs successfully assigned.  Therefore, delete these printks
entirely.

Spotted by Russell King.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>

Instead of having board code poke directly into the MPP configuration
registers, and separately calling orion5x_gpio_set_valid_pins() to
indicate which MPP pins can be used as GPIO pins, introduce a helper
function for configuring the roles of each of the MPP pins, and have
that helper function handle gpio validity internally.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Acked-by: Russell King <linux@arm.linux.org.uk>

It makes no sense to do PCIe WA window setup in the individual
board support files while the decision whether or not to use the
PCIe WA access method is made in a different place, in the PCIe
support code.

This patch moves the configuration of a PCIe WA window from the
individual Orion board support files to the central Orion PCIe
support code.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>

This patch moves initialisation of EHCI/I2C/UART platform devices
from the common orion5x_init() into the board support code.

The rationale behind this is that only the board support code knows
whether certain peripherals have been brought out on the board, and
not initialising peripherals that haven't been brought out is
desirable for example:
- to reduce user confusion (e.g. seeing both 'eth0' and 'eth1'
  appear while there is only one ethernet port on the board); and
- to allow for future power savings (peripherals that have not
  been brought out can be clock gated off entirely).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>

This define isn't used anywhere in the kernel tree -- nuke it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>

Make it clear that Orion top-level IRQs are level-triggered.  This
means that we don't need an ->ack() handler, or at least, we don't
need the ->ack() handler (or the acking part of the ->mask_ack()
handler) to actually do anything.

Given that, we might as well point our ->mask_ack() handler at the
->mask() handler instead of providing a dummy ->ack() handler, since
providing a ->mask_ack() handler on level IRQ sources will prevent
->ack() from ever being called.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>

Annotate the entries for the 88fr531-vd CPU core in
arch/arm/boot/compressed/head.S and arch/arm/mm/proc-feroceon.S
with the full name of the core.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>

The DRAM base address and size fields in the CPU's MBUS bridge have
64KiB granularity, instead of the currently used 16MiB.  Since all
of the currently supported MBUS peripherals support 64KiB granularity
as well, this patch changes the Orion address map code to stop
rounding base addresses down and sizes up to multiples of 16MiB.

Found by Ke Wei <kewei@marvell.com>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>

Currently, Orion window setup uses hardcoded window indexes for each
of the boot/cs0/cs1/cs2/PCIe WA windows.  The static window allocation
used can clash if board support code will ever attempt to configure
both a dev2 and a PCIe WA window, as both of those use CPU mbus window
#7 at present.

This patch keeps track of the last used window, and opens subsequently
requested windows sequentially, starting from 4.  (Windows 0-3 are used
as MEM/IO windows for the PCI/PCIe buses.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

More cosmetic cleanup:
- Replace 8-space indents by proper tab indents.
- In structure initialisers, use a trailing comma for every member.
- Collapse "},\n{" in structure initialiers to "}, {".
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>

This is a natural extension following the previous patch.
Non Feroceon based targets are unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

The implementation for memory copy functions on ARM had a (disabled)
provision for aligning the source pointer before loading registers with
data.  Turns out that aligning the _destination_ pointer is much more
useful, as the read side is already sufficiently helped with the use of
preload.

So this changes the definition of the CALGN() macro to target the
destination pointer instead, and turns it on for Feroceon processors
where the gain is very noticeable.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

This code is currently disabled, which explains why no one was affected.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Available for !SMP only at the moment.

From Russell:

|Basically, if a thread is running on a CPU, thread_saved_fp() is invalid.
|So, the question is: what guarantees do we have here that 'tsk' is not
|running on another CPU?
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  BAST: Remove old IDE driver
  pcmcia ide kingston compactflash's have a new manufacturer id
  pcmcia: add another pata/ide ID
  pcmcia: add an pata/ide ID
  ide: increase timeout in wait_drive_not_busy()
  palm_bk3710: fix resource management

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  ieee1394: Kconfig menu touch-up
  firewire: Kconfig menu touch-up
  firewire: deadline for PHY config transmission
  firewire: fw-ohci: unify printk prefixes
  firewire: fill_bus_reset_event needs lock protection
  firewire: fw-ohci: write selfIDBufferPtr before LinkControl.rcvSelfID
  firewire: fw-ohci: disable PHY packet reception into AR context
  firewire: fw-ohci: use of uninitialized data in AR handler
  firewire: don't panic on invalid AR request buffer

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: no AC status notification
  ACPI Exception (video-1721): UNKNOWN_STATUS_CODE, Cant attach device

* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (21 commits)
  drm: only trust core drm ioctls - driver ioctls are a mess.
  drm/i915: add support for Intel series 4 chipsets.
  drm/radeon: add hier-z registers for r300 and r500 chipsets
  drm/radeon: use DSTCACHE_CTLSTAT rather than RB2D_DSTCACHE_CTLSTAT
  drm/radeon: switch IGP gart to use radeon_write_agp_base()
  drm/radeon: Restore sw interrupt on resume
  drm/r500: add support for AGP based cards.
  drm/radeon: fix texture uploads with large 3d textures (bug 13980)
  drm/radeon: add initial r500 support.
  drm/radeon: init pipe setup in kernel code.
  drm/radeon: fixup radeon_do_engine_reset
  drm/radeon: fix pixcache and purge/cache flushing registers
  drm/radeon: write AGP_BASE_2 on chips that support it.
  drm/radeon: merge IGP chip setup and fixup RS400 vs RS480 support
  drm/radeon: IGP clean up register and magic numbers.
  drm/rs690: set base 2 to 0.
  drm/rs690: set all of gart base address.
  radeon: add production microcode from AMD
  drm: pcigart use proper pci map interfaces.
  drm: the sg alloc ioctl should write back the handle to userspace
  ...

* 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
  [agp]: fixup chipset flush for new Intel G4x.
  agp: brown paper bag patch - put back the two lines it took out.

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  softlockup: fix NMI hangs due to lock race - 2.6.26-rc regression
  rcupreempt: remove export of rcu_batches_completed_bh
  cpuset: limit the input of cpuset.sched_relax_domain_level

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched, delay accounting: fix incorrect delay time when constantly waiting on runqueue
  sched: CPU hotplug events must not destroy scheduler domains created by the cpusets
  sched: rt-group: fix RR buglet
  sched: rt-group: heirarchy aware throttle
  sched: rt-group: fix hierarchy
  sched: NULL pointer dereference while setting sched_rt_period_us
  sched: fix defined-but-unused warning

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, geode: add a VSA2 ID for General Software
  x86: use BOOTMEM_EXCLUSIVE on 32-bit
  x86, 32-bit: fix boot failure on TSC-less processors
  x86: fix NULL pointer deref in __switch_to
  x86: set PAE PHYSICAL_MASK_SHIFT to 44 bits.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
  Blackfin Serial Driver: Use timer to poll CTS PIN instead of workqueue.
  Blackfin arch: fix typo error in bf548 serial header file

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ahci: sis can't do PMP
  ata_piix: add TECRA M4 to broken suspend list
  LIBATA: Add HAVE_PATA_PLATFORM to select PATA_PLATFORM driver
  sata_mv: warn on PIO with multiple DRQs
  sata_mv: enable async_notify for 60x1 Rev.C0 and higher
  libata: don't check whether to use DMA or not for no data commands
  ahci: jmb361 has only one port

The inline assembly in drivers/watchdog/hpwdt.c was incredibly broken,
and included all the function prologue and epilogue stuff, even though
it was itself then inside a C function where the compiler would add its
own prologue and epilogue on top of it all.

This then just _happened_ to work if you had exactly the right compiler
version and exactly the right compiler flags, so that gcc just happened
to not create any prologue at all (the gcc-generated epilogue wouldn't
matter, since it would never be reached).

But the more proper way to fix it is to simply not do this.  Move the
inline asm to the top level, with no surrounding function at all (the
better alternative would be to remove the prologue and make it actually
use proper description of the arguments to the inline asm, but that's a
bigger change than the one I'm willing to make right now).
Tested-by: S.Çağlar Onur <caglar@pardus.org.tr>
Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>