A3700 comphy initialization is done in the firmware (TF-A). Looking at
the SATA PHY initialization routine, there is a comment about "vendor
specific" registers. Two registers are mentioned. They are not
initialized there in the firmware because they are AHCI related, while
the firmware at this location does only PHY configuration. The
solution to avoid doing such initialization is relying on U-Boot.

While this work at boot time, U-Boot is definitely not going to run
during a resume after suspending to RAM.

Two possible solutions were considered:
* Fixing the firmware.
* Fixing the kernel driver.

The first solution would take ages to propagate, while the second
solution is easy to implement as the driver as been a little bit
reworked to prepare for such platform configuration. Hence, this patch
adds an Armada 3700 configuration function to set these two registers
both at boot time (in the probe) and after a suspend (in the resume
path).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

At the beginning, only Armada 38x SoCs where supported by the
ahci_mvebu.c driver. Commit 15d3ce7b ("ata: ahci_mvebu: add
support for Armada 3700 variant") introduced Armada 3700 support. As
opposed to Armada 38x SoCs, the 3700 variants do not have to configure
mbus and the regret option. This patch took care of avoiding such
configuration when not needed in the probe function, but failed to do
the same in the resume path. While doing so looks harmless by
experience, let's clean the driver logic and avoid doing this useless
configuration with Armada 3700 SoCs.

Because the logic is very similar between these two places, it has
been decided to factorize this code and put it in a "Armada 38x
configuration function". This function is part of a new
(per-compatible) platform data structure, so that the addition of such
configuration function for Armada 3700 will be eased.

Fixes: 15d3ce7b ("ata: ahci_mvebu: add support for Armada 3700 variant")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

For Armada-38x (32-bit) SoCs, PM platform support has been added since:
commit 32f9494c ("ARM: mvebu: prepare pm-board.c for the
                      introduction of Armada 38x support")
commit 3cbd6a6c ("ARM: mvebu: Add standby support")

For Armada 64-bit SoCs, like the A3700 also using this AHCI driver, PM
platform support has always existed.

There are even suspend/resume hooks in this driver since:
commit d6ecf158 ("ata: ahci_mvebu: add suspend/resume support")

Remove the stale comment at the end of this driver stating that all
the above does not exist yet.

Fixes: d6ecf158 ("ata: ahci_mvebu: add suspend/resume support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Current implementation of the libahci does not take into account the
new PHY framework. Correct the situation by adding a call to
phy_set_mode() before phy_power_on().

PHYs should also be handled at suspend/resume time. For this, call
ahci_platform_enable/disable_phys() at suspend/resume_host() time. These
calls are guarded by a HFLAG (AHCI_HFLAG_SUSPEND_PHYS) that the user of
the libahci driver must set manually in hpriv->flags at probe time. This
is to avoid breaking users that have not been tested with this change.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull NVMe fixes from Christoph.

* 'nvme-5.0' of git://git.infradead.org/nvme:
  nvme: don't initlialize ctrl->cntlid twice
  nvme: introduce NVME_QUIRK_IGNORE_DEV_SUBNQN
  nvme: pad fake subsys NQN vid and ssvid with zeros
  nvme-multipath: zero out ANA log buffer
  nvme-fabrics: unset write/poll queues for discovery controllers
  nvme-tcp: don't ask if controller is fabrics
  nvme-tcp: remove dead code
  nvme-pci: fix out of bounds access in nvme_cqe_pending
  nvme-pci: rerun irq setup on IO queue init errors
  nvme-pci: use the same attributes when freeing host_mem_desc_bufs.
  nvme-pci: fix the wrong setting of nr_maps

If we don't drop caches used in old offset or block_size, we can get old data
from new offset/block_size, which gives unexpected data to user.

For example, Martijn found a loopback bug in the below scenario.
1) LOOP_SET_FD loads first two pages on loop file
2) LOOP_SET_STATUS64 changes the offset on the loop file
3) mount is failed due to the cached pages having wrong superblock

Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Reported-by: Martijn Coenen <maco@google.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Commit 5f0ed774 ("block: sum requests in the plug structure") removed
the request_count parameter from block_attempt_plug_merge(), but did not
remove the associated kerneldoc comment, introducing this warning to the
docs build:

  ./block/blk-core.c:685: warning: Excess function parameter 'request_count' description in 'blk_attempt_plug_merge'

Remove the obsolete description and make things a little quieter.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

ctrl->cntlid will already be initialized from id->cntlid for
non-NVME_F_FABRICS controllers few lines below. For NVME_F_FABRICS
controllers this field should already be initialized, otherwise the
check

	if (ctrl->cntlid != le16_to_cpu(id->cntlid))

below will always be a no-op.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>

If a device provides an NQN it is expected to be globally unique.
Unfortunately some firmware revisions for Intel 760p/Pro 7600p devices did
not satisfy this requirement.  In these circumstances if a system has >1
affected device then only one device is enabled.  If this quirk is enabled
then the device supplied subnqn is ignored and we fallback to generating
one as if the field was empty.  In this case we also suppress the version
check so we don't print a warning when the quirk is enabled.
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: James Dingwall <james@dingwall.me.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>

We need to preserve the leading zeros in the vid and ssvid when generating
a unique NQN. Truncating these may lead to naming collisions.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

When nvme_init_identify() fails the ANA log buffer is deallocated
but _not_ set to NULL. This can cause double free oops when this
controller is deleted without ever being reconnected.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Even if user-space sent it to us, it got it wrong so lets
help by disallowing it.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>

For sure we are a fabric driver.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>

We should never touch the opal device from the transport driver.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>

There is an out of bounds array access in nvme_cqe_peding().

When enable irq_thread for nvme interrupt, there is racing between the
nvmeq->cq_head updating and reading.

nvmeq->cq_head is updated in nvme_update_cq_head(), if nvmeq->cq_head
equals nvmeq->q_depth and before its value set to zero, nvme_cqe_pending()
uses its value as an array index, the index will be out of bounds.
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
[hch: slight coding style update]
Signed-off-by: Christoph Hellwig <hch@lst.de>

If the driver is unable to create a subset of IO queues for any reason,
the read/write and polled queue sets will not match the actual allocated
hardware contexts. This leaves gaps in the CPU affinity mappings and
causes the following kernel panic after blk_mq_map_queue_type() returns
a NULL hctx.

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000198
  #PF error: [normal kernel read fault]
  PGD 0 P4D 0
  Oops: 0000 [#1] SMP
  CPU: 64 PID: 1171 Comm: kworker/u259:1 Not tainted 4.20.0+ #241
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-2.fc27 04/01/2014
  Workqueue: nvme-wq nvme_scan_work [nvme_core]
  RIP: 0010:blk_mq_init_allocated_queue+0x2d9/0x440
  RSP: 0018:ffffb1bf0abc3cd0 EFLAGS: 00010286
  RAX: 000000000000001f RBX: ffff8ea744cf0718 RCX: 0000000000000000
  RDX: 0000000000000002 RSI: 000000000000007c RDI: ffffffff9109a820
  RBP: ffff8ea7565f7008 R08: 000000000000001f R09: 000000000000003f
  R10: ffffb1bf0abc3c00 R11: 0000000000000000 R12: 000000000001d008
  R13: ffff8ea7565f7008 R14: 000000000000003f R15: 0000000000000001
  FS:  0000000000000000(0000) GS:ffff8ea757200000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000000000198 CR3: 0000000013058000 CR4: 00000000000006e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   blk_mq_init_queue+0x35/0x60
   nvme_validate_ns+0xc6/0x7c0 [nvme_core]
   ? nvme_identify_ctrl.isra.56+0x7e/0xc0 [nvme_core]
   nvme_scan_work+0xc8/0x340 [nvme_core]
   ? __wake_up_common+0x6d/0x120
   ? try_to_wake_up+0x55/0x410
   process_one_work+0x1e9/0x3d0
   worker_thread+0x2d/0x3d0
   ? process_one_work+0x3d0/0x3d0
   kthread+0x111/0x130
   ? kthread_park+0x90/0x90
   ret_from_fork+0x1f/0x30
  Modules linked in: nvme nvme_core serio_raw
  CR2: 0000000000000198

Fix by re-running the interrupt vector setup from scratch using a reduced
count that may be successful until the created queues matches the irq
affinity plus polling queue sets.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

When using HMB the PCIe host driver allocates host_mem_desc_bufs using
dma_alloc_attrs() but frees them using dma_free_coherent(). Use the
correct dma_free_attrs() function to free the buffers.
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>

We only set the nr_maps to 3 if poll queues are supported.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Of the tunables available for the bfq I/O scheduler, the only one
missing from the documentation in 'Documentation/block/bfq-iosched.txt'
is slice_idle_us. Add this tunable to the documentation and a short
explanation of its purpose.
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

There was some confusion about what these functions did.  Make it clear
that this is a hint for upper layers to pass to the block layer, and
that it does not guarantee that I/O will not be submitted between a
start and finish plug.
Reported-by: "Darrick J. Wong" <darrick.wong@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

If the kernel is built without CONFIG_BLK_DEV_ZONED, a modprobe
of the null_blk driver with zoned=1 fails with 'Invalid argument'.
This can be confusing to users, prompting a search as to why the
parameter is invalid. To assist in that search, add a bit more
information to the failure, additionally adding to the documentation
that CONFIG_BLK_DEV_ZONED is needed for zoned=1.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: John Pittman <jpittman@redhat.com>

Added null_blk prefix to error message.
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Add documentation for /sys/block/<disk>/queue/io_timeout.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Weiping Zhang <zhangweiping@didiglobal.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Signed-off-by: Jens Axboe <axboe@kernel.dk>

vdc_blk_queue_start() may be called from irq context, so we can't run
queue via blk_mq_start_hw_queues() since we never allow to run queue
from irq context. Use blk_mq_start_stopped_hw_queues(q, true) to fix
this issue.

Fixes: fa182a1f ("sunvdc: convert to blk-mq")
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com>
Cc: Anatoly Pugachev <matorola@gmail.com>
Cc: sparclinux@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull the pending 4.21 changes for md from Shaohua.

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md: fix raid10 hang issue caused by barrier
  raid10: refactor common wait code from regular read/write request
  md: remvoe redundant condition check
  lib/raid6: add option to skip algo benchmarking
  lib/raid6: sort algos in rough performance order
  lib/raid6: check for assembler SSSE3 support
  lib/raid6: avoid __attribute_const__ redefinition
  lib/raid6: add missing include for raid6test
  md: remove set but not used variable 'bi_rdev'

Pull input updates from Dmitry Torokhov:
 "A tiny pull request this merge window unfortunately, should get more
  material in for the next release:

   - new driver for Raspberry Pi's touchscreen (firmware interface)

   - miscellaneous input driver fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: elan_i2c - add ACPI ID for touchpad in ASUS Aspire F5-573G
  Input: atmel_mxt_ts - don't try to free unallocated kernel memory
  Input: drv2667 - fix indentation issues
  Input: touchscreen - fix coding style issue
  Input: add official Raspberry Pi's touchscreen driver
  Input: nomadik-ske-keypad - fix a loop timeout test
  Input: rotary-encoder - don't log EPROBE_DEFER to kernel log
  Input: olpc_apsp - remove set but not used variable 'np'
  Input: olpc_apsp - enable the SP clock
  Input: olpc_apsp - check FIFO status on open(), not probe()
  Input: olpc_apsp - drop CONFIG_OLPC dependency
  clk: mmp2: add SP clock
  dt-bindings: marvell,mmp2: Add clock id for the SP clock
  Input: ad7879 - drop platform data support

Pull virtio/vhost updates from Michael Tsirkin:
"Features, fixes, cleanups:

   - discard in virtio blk

   - misc fixes and cleanups"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  vhost: correct the related warning message
  vhost: split structs into a separate header file
  virtio: remove deprecated VIRTIO_PCI_CONFIG()
  vhost/vsock: switch to a mutex for vhost_vsock_hash
  virtio_blk: add discard and write zeroes support

Pull more block updates from Jens Axboe:

 - Dead code removal for loop/sunvdc (Chengguang)

 - Mark BIDI support for bsg as deprecated, logging a single dmesg
   warning if anyone is actually using it (Christoph)

 - blkcg cleanup, killing a dead function and making the tryget_closest
   variant easier to read (Dennis)

 - Floppy fixes, one fixing a regression in swim3 (Finn)

 - lightnvm use-after-free fix (Gustavo)

 - gdrom leak fix (Wenwen)

 - a set of drbd updates (Lars, Luc, Nathan, Roland)

* tag 'for-4.21/block-20190102' of git://git.kernel.dk/linux-block: (28 commits)
  block/swim3: Fix regression on PowerBook G3
  block/swim3: Fix -EBUSY error when re-opening device after unmount
  block/swim3: Remove dead return statement
  block/amiflop: Don't log error message on invalid ioctl
  gdrom: fix a memory leak bug
  lightnvm: pblk: fix use-after-free bug
  block: sunvdc: remove redundant code
  block: loop: remove redundant code
  bsg: deprecate BIDI support in bsg
  blkcg: remove unused __blkg_release_rcu()
  blkcg: clean up blkg_tryget_closest()
  drbd: Change drbd_request_detach_interruptible's return type to int
  drbd: Avoid Clang warning about pointless switch statment
  drbd: introduce P_ZEROES (REQ_OP_WRITE_ZEROES on the "wire")
  drbd: skip spurious timeout (ping-timeo) when failing promote
  drbd: don't retry connection if peers do not agree on "authentication" settings
  drbd: fix print_st_err()'s prototype to match the definition
  drbd: avoid spurious self-outdating with concurrent disconnect / down
  drbd: do not block when adjusting "disk-options" while IO is frozen
  drbd: fix comment typos
  ...

Pull libata fix from Jens Axboe:
 "This libata change missed the original libata pull request.

  Just a single fix in here, fixing a missed reference drop"

* tag 'for-4.21/libata-20190102' of git://git.kernel.dk/linux-block:
  ata: pata_macio: add of_node_put()

Pull more clk updates from Stephen Boyd:
 "One more patch to generalize a set of DT binding defines now before
  -rc1 comes out.

  This way the SoC DTS files can use the proper defines from a stable
  tag"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: imx8qxp: make the name of clock ID generic

Pull device properties framework fixes from Rafael Wysocki:
 "Fix two potential NULL pointer dereferences found by Coverity in the
  software nodes code introduced recently (Colin Ian King)"

* tag 'devprop-4.21-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  drivers: base: swnode: check if swnode is NULL before dereferencing it
  drivers: base: swnode: check if pointer p is NULL before dereferencing it

Pull mailbox updates from Jassi Brar:

 - Introduce device-managed registration
   devm_mbox_controller_un/register and convert drivers to use it

 - Introduce flush api to support clients that must busy-wait in atomic
   context

 - Support multiple controllers per device

 - Hi3660: a bugfix and constify ops structure

 - TI-MsgMgr: off by one bugfix.

 - BCM: switch to spdx license

 - Tegra-HSP: support for shared mailboxes and suspend/resume.

* tag 'mailbox-v4.21' of git://git.linaro.org/landing-teams/working/fujitsu/integration: (30 commits)
  mailbox: tegra-hsp: Use device-managed registration API
  mailbox: tegra-hsp: use devm_kstrdup_const()
  mailbox: tegra-hsp: Add suspend/resume support
  mailbox: tegra-hsp: Add support for shared mailboxes
  dt-bindings: tegra186-hsp: Add shared mailboxes
  mailbox: Allow multiple controllers per device
  mailbox: Support blocking transfers in atomic context
  mailbox: ti-msgmgr: Use device-managed registration API
  mailbox: stm32-ipcc: Use device-managed registration API
  mailbox: rockchip: Use device-managed registration API
  mailbox: qcom-apcs: Use device-managed registration API
  mailbox: platform-mhu: Use device-managed registration API
  mailbox: omap: Use device-managed registration API
  mailbox: mtk-cmdq: Remove needless devm_kfree() calls
  mailbox: mtk-cmdq: Use device-managed registration API
  mailbox: xgene-slimpro: Use device-managed registration API
  mailbox: sti: Use device-managed registration API
  mailbox: altera: Use device-managed registration API
  mailbox: imx: Use device-managed registration API
  mailbox: hi6220: Use device-managed registration API
  ...

Pull UML updates from Richard Weinberger:

 - DISCARD support for our block device driver

 - Many TLB flush optimizations

 - Various smaller fixes

 - And most important, Anton agreed to help me maintaining UML

* 'for-linus-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Remove obsolete reenable_XX calls
  um: writev needs <sys/uio.h>
  Add Anton Ivanov to UML maintainers
  um: remove redundant generic-y
  um: Optimize Flush TLB for force/fork case
  um: Avoid marking pages with "changed protection"
  um: Skip TLB flushing where not needed
  um: Optimize TLB operations v2
  um: Remove unnecessary faulted check in uaccess.c
  um: Add support for DISCARD in the UBD Driver
  um: Remove unsafe printks from the io thread
  um: Clean-up command processing in UML UBD driver
  um: Switch to block-mq constants in the UML UBD driver
  um: Make GCOV depend on !KCOV
  um: Include sys/uio.h to have writev()
  um: Add HAVE_DEBUG_BUGVERBOSE
  um: Update maintainers file entry

Pull s390 updates from Martin Schwidefsky:

 - A larger update for the zcrypt / AP bus code:
    + Update two inline assemblies in the zcrypt driver to make gcc happy
    + Add a missing reply code for invalid special commands for zcrypt
    + Allow AP device reset to be triggered from user space
    + Split the AP scan function into smaller, more readable functions

 - Updates for vfio-ccw and vfio-ap
    + Add maintainers and reviewer for vfio-ccw
    + Include facility.h in vfio_ap_drv.c to avoid fragile include chain
    + Simplicy vfio-ccw state machine

 - Use the common code version of bust_spinlocks

 - Make use of the DEFINE_SHOW_ATTRIBUTE

 - Fix three incorrect file permissions in the DASD driver

 - Remove bit spin-lock from the PCI interrupt handler

 - Fix GFP_ATOMIC vs GFP_KERNEL in the PCI code

* tag 's390-4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/zcrypt: rework ap scan bus code
  s390/zcrypt: make sysfs reset attribute trigger queue reset
  s390/pci: fix sleeping in atomic during hotplug
  s390/pci: remove bit_lock usage in interrupt handler
  s390/drivers: fix proc/debugfs file permissions
  s390: convert to DEFINE_SHOW_ATTRIBUTE
  MAINTAINERS/vfio-ccw: add Farhan and Eric, make Halil Reviewer
  vfio: ccw: Merge BUSY and BOXED states
  s390: use common bust_spinlocks()
  s390/zcrypt: improve special ap message cmd handling
  s390/ap: rework assembler functions to use unions for in/out register variables
  s390: vfio-ap: include <asm/facility> for test_facility()

Pull NFS client updates from Anna Schumaker:
 "Stable bugfixes:
   - xprtrdma: Yet another double DMA-unmap # v4.20

  Features:
   - Allow some /proc/sys/sunrpc entries without CONFIG_SUNRPC_DEBUG
   - Per-xprt rdma receive workqueues
   - Drop support for FMR memory registration
   - Make port= mount option optional for RDMA mounts

  Other bugfixes and cleanups:
   - Remove unused nfs4_xdev_fs_type declaration
   - Fix comments for behavior that has changed
   - Remove generic RPC credentials by switching to 'struct cred'
   - Fix crossing mountpoints with different auth flavors
   - Various xprtrdma fixes from testing and auditing the close code
   - Fixes for disconnect issues when using xprtrdma with krb5
   - Clean up and improve xprtrdma trace points
   - Fix NFS v4.2 async copy reboot recovery"

* tag 'nfs-for-4.21-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (63 commits)
  sunrpc: convert to DEFINE_SHOW_ATTRIBUTE
  sunrpc: Add xprt after nfs4_test_session_trunk()
  sunrpc: convert unnecessary GFP_ATOMIC to GFP_NOFS
  sunrpc: handle ENOMEM in rpcb_getport_async
  NFS: remove unnecessary test for IS_ERR(cred)
  xprtrdma: Prevent leak of rpcrdma_rep objects
  NFSv4.2 fix async copy reboot recovery
  xprtrdma: Don't leak freed MRs
  xprtrdma: Add documenting comment for rpcrdma_buffer_destroy
  xprtrdma: Replace outdated comment for rpcrdma_ep_post
  xprtrdma: Update comments in frwr_op_send
  SUNRPC: Fix some kernel doc complaints
  SUNRPC: Simplify defining common RPC trace events
  NFS: Fix NFSv4 symbolic trace point output
  xprtrdma: Trace mapping, alloc, and dereg failures
  xprtrdma: Add trace points for calls to transport switch methods
  xprtrdma: Relocate the xprtrdma_mr_map trace points
  xprtrdma: Clean up of xprtrdma chunk trace points
  xprtrdma: Remove unused fields from rpcrdma_ia
  xprtrdma: Cull dprintk() call sites
  ...

Pull nfsd updates from Bruce Fields:
 "Thanks to Vasily Averin for fixing a use-after-free in the
  containerized NFSv4.2 client, and cleaning up some convoluted
  backchannel server code in the process.

  Otherwise, miscellaneous smaller bugfixes and cleanup"

* tag 'nfsd-4.21' of git://linux-nfs.org/~bfields/linux: (25 commits)
  nfs: fixed broken compilation in nfs_callback_up_net()
  nfs: minor typo in nfs4_callback_up_net()
  sunrpc: fix debug message in svc_create_xprt()
  sunrpc: make visible processing error in bc_svc_process()
  sunrpc: remove unused xpo_prep_reply_hdr callback
  sunrpc: remove svc_rdma_bc_class
  sunrpc: remove svc_tcp_bc_class
  sunrpc: remove unused bc_up operation from rpc_xprt_ops
  sunrpc: replace svc_serv->sv_bc_xprt by boolean flag
  sunrpc: use-after-free in svc_process_common()
  sunrpc: use SVC_NET() in svcauth_gss_* functions
  nfsd: drop useless LIST_HEAD
  lockd: Show pid of lockd for remote locks
  NFSD remove OP_CACHEME from 4.2 op_flags
  nfsd: Return EPERM, not EACCES, in some SETATTR cases
  sunrpc: fix cache_head leak due to queued request
  nfsd: clean up indentation, increase indentation in switch statement
  svcrdma: Optimize the logic that selects the R_key to invalidate
  nfsd: fix a warning in __cld_pipe_upcall()
  nfsd4: fix crash on writing v4_end_grace before nfsd startup
  ...

Pull 9p updates from Dominique Martinet:
 "Missing prototype warning fix and a syzkaller fix when a 9p server
  advertises a too small msize"

* tag '9p-for-4.21' of git://github.com/martinetd/linux:
  9p/net: put a lower bound on msize
  net/9p: include trans_common.h to fix missing prototype warning.

Pull cifs updates from Steve French:

 - four fixes for stable

 - improvements to DFS including allowing failover to alternate targets

 - some small performance improvements

* tag '4.21-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6: (39 commits)
  cifs: update internal module version number
  cifs: we can not use small padding iovs together with encryption
  cifs: Minor Kconfig clarification
  cifs: Always resolve hostname before reconnecting
  cifs: Add support for failover in cifs_reconnect_tcon()
  cifs: Add support for failover in smb2_reconnect()
  cifs: Only free DFS target list if we actually got one
  cifs: start DFS cache refresher in cifs_mount()
  cifs: Use GFP_ATOMIC when a lock is held in cifs_mount()
  cifs: Add support for failover in cifs_reconnect()
  cifs: Add support for failover in cifs_mount()
  cifs: remove set but not used variable 'sep'
  cifs: Make use of DFS cache to get new DFS referrals
  cifs: minor updates to documentation
  cifs: check kzalloc return
  cifs: remove set but not used variable 'server'
  cifs: Use kzfree() to free password
  cifs: Fix to use kmem_cache_free() instead of kfree()
  cifs: update for current_kernel_time64() removal
  cifs: Add DFS cache routines
  ...

Pull TPM updates from James Morris:

 - Support for partial reads of /dev/tpm0.

 - Clean up for TPM 1.x code: move the commands to tpm1-cmd.c and make
   everything to use the same data structure for building TPM commands
   i.e. struct tpm_buf.

* 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (25 commits)
  tpm: add support for partial reads
  tpm: tpm_ibmvtpm: fix kdoc warnings
  tpm: fix kdoc for tpm2_flush_context_cmd()
  tpm: tpm_try_transmit() refactor error flow.
  tpm: use u32 instead of int for PCR index
  tpm1: reimplement tpm1_continue_selftest() using tpm_buf
  tpm1: reimplement SAVESTATE using tpm_buf
  tpm1: rename tpm1_pcr_read_dev to tpm1_pcr_read()
  tpm1: implement tpm1_pcr_read_dev() using tpm_buf structure
  tpm: tpm1: rewrite tpm1_get_random() using tpm_buf structure
  tpm: tpm-space.c remove unneeded semicolon
  tpm: tpm-interface.c drop unused macros
  tpm: add tpm_auto_startup() into tpm-interface.c
  tpm: factor out tpm_startup function
  tpm: factor out tpm 1.x pm suspend flow into tpm1-cmd.c
  tpm: move tpm 1.x selftest code from tpm-interface.c tpm1-cmd.c
  tpm: factor out tpm1_get_random into tpm1-cmd.c
  tpm: move tpm_getcap to tpm1-cmd.c
  tpm: move tpm1_pcr_extend to tpm1-cmd.c
  tpm: factor out tpm_get_timeouts()
  ...

Pull smack updates from James Morris:
 "Two Smack patches for 4.21.

  Jose's patch adds missing documentation and Zoran's fleshes out the
  access checks on keyrings"

* 'next-smack' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  Smack: Improve Documentation
  smack: fix access permissions for keyring