- 05 Jun, 2015 9 commits
-
-
Mauro Carvalho Chehab authored
As reported by smatch: drivers/media/dvb-frontends/drxk_hard.c:3277 dvbt_sc_command() warn: missing break? reassigning 'status' This is basically because the error handling logic there was crappy. Signed-off-by:Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-
Mauro Carvalho Chehab authored
Remove the following compilation warnings: drivers/media/platform/vivid/vivid-tpg.c: In function 'tpg_gen_text': drivers/media/platform/vivid/vivid-tpg.c:1562:1: warning: the frame size of 1308 bytes is larger than 1024 bytes [-Wframe-larger-than=] } ^ This seems to be due to some bad optimization done by gcc. Moving the for() loop to happen inside the macro solves the issue. While here, fix CodingStyle at the switch(). Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com>
-
Marek Szyprowski authored
Commits a0f10c13 and 6c9fe765 ("media: s5p-mfc: fix broken pointer cast on 64bit arch") fixed issue with lossy cast on 64-bit architectures. However it also removed __iomem attribute from that cast. This leads to sparse warnings. This patch fixes those warnings by adding __iomem cast in case of v6+ code version and replacing readl/writel by simple u32 load/store operations in case of v5 code (which is called on system memory allocated by dma_alloc_coherent() instead of io registers). Reported-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
Lad, Prabhakar authored
this patch makes use of helper function v4l2_get_timestamp() to set the timestamp of vb2 buffer. Signed-off-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
-
Lad, Prabhakar authored
V4L2 drivers should use MONOTONIC timestamps instead of gettimeofday, which is affected by daylight savings time. Signed-off-by:
-
Lad, Prabhakar authored
this patch sets nbuffers to three or more and drops the unset member video_limit which just a copy paste from earlier driver. Signed-off-by:
-
Lad, Prabhakar authored
clear of the output_specs before passing it to the configure_resizer_out_params(), so that no garbage values are set. This fixes following build warning: drivers/staging/media/davinci_vpfe/dm365_resizer.c: In function 'resizer_set_stream': drivers/staging/media/davinci_vpfe/dm365_resizer.c:190:46: warning: 'output_specs.vst_c' may be used uninitialized in this function [-Wmaybe-uninitialized] param->ext_mem_param[index].rsz_sdr_ptr_s_c = output->vst_c; ^ drivers/staging/media/davinci_vpfe/dm365_resizer.c:316:30: note: 'output_specs.vst_c' was declared here struct vpfe_rsz_output_spec output_specs; ^ Signed-off-by: -
Antti Palosaari authored
Implement DVBv5 signal strength stats. Returns dBm. Signed-off-by:
Antti Palosaari <crope@iki.fi> Tested-by:
Adam Baker <linux@baker-net.org.uk> Signed-off-by:
-
Antti Palosaari authored
We need own I2C locking because of tuner I2C adapter/repeater. Firmware command is executed using I2C send + reply message. Default I2C adapter locking protects only single I2C operation, not whole send + reply sequence as needed. Due to that, it was possible tuner I2C message interrupts firmware command sequence. Reported-by:
-
- 01 Jun, 2015 5 commits
-
-
Mauro Carvalho Chehab authored
FE_SET_PROPERTY/FE_GET_PROPERTY actually expects a struct dtv_properties argument. Signed-off-by: -
Mauro Carvalho Chehab authored
The changeset dc9ef7d1 change the open() ioctl documentation to match the V4L2 open(). However, some cut-and-pasted stuff doesn't match what actually happens at the DVB core. So, fix the documentation entry to be more accurate with the DVB frontend open() specifics. Signed-off-by:
-
Hans Verkuil authored
To fix the last xmllint errors the open and close function reference description was rewritten based on the v4l2 open and close functions. Signed-off-by:
-
Hans Verkuil authored
Fixes a large number of xmllint errors. Signed-off-by:
-
Hans Verkuil authored
satellital -> satellite antena -> antenna Signed-off-by:
-
- 30 May, 2015 26 commits
-
-
Laurent Pinchart authored
The UVC_DEV_DISCONNECTED flag is set when the USB device is disconnected, and checked in the open() handler to refuse opening a device that has been disconnected. This is inherently racy, but the race condition is taken care of in the V4L2 core, which also fails open() calls when the V4L2 device node has been unregistered. As the uvcvideo USB disconnect handler unregisters all its video device nodes, the UVC_DEV_DISCONNECTED flag doesn't serve any purpose anymore and can be removed. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
The "TOSHIBA Web Camera - 5M" Chicony device (04f2:b50b) seems to compute the bandwidth on 16 bits and erroneously sign-extend it to 32 bits, resulting in a huge bandwidth value. Detect and fix that condition by setting the 16 MSBs to 0 when they're all equal to 1. Reported-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Laurent Pinchart authored
Now that videobuf2-vmalloc supports exporting buffers, add support for the DMABUF exporter role by plugging in the videobuf2 ioctl helper. Signed-off-by:
-
Antti Palosaari authored
It is AF9035 + MxL5007T. Driver reports: prechip_version=00 chip_version=03 chip_type=3802 Not sure if that USB ID is reserved only for HP brand or if it is common, but the stick I have is branded as HP part no. 580715-001 rmn A867. Signed-off-by:
-
Antti Palosaari authored
Implement I2C client device binding. Wrap media attach to driver I2C probe. Add wrapper from m88ds3103_attach() to m88ds3103_probe() via driver core in order to provide proper I2C client for legacy media attach binding. Signed-off-by:
-
Antti Palosaari authored
Use jiffies to set timeout for DiSEqC TX ready polling. Using jiffies is more elegant solution than looping N times with sleep. Signed-off-by:
-
Antti Palosaari authored
Implement DVBv5 BER statistics. Wrap legacy DVBv3 BER to DVBv5 BER. Signed-off-by:
-
Antti Palosaari authored
Implement DVBv5 CNR statistics. Wrap legacy DVBv3 SNR to DVBv5 CNR. Signed-off-by:
-
Antti Palosaari authored
Do not return error from get_frontend() when status is queried, but the frontend didn't lock yet. The proper behavior is to only update the cache after having a lock. [mchehab@osg.samsung.com: fix the patch description] Signed-off-by:
-
Vasily Khoruzhick authored
Autogain algorithm is very simple, if average luminance is low - increase gain, if it's high - decrease gain. Gain granularity is low enough for this algo to stabilize quickly. Signed-off-by:
Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by:
-
Vasily Khoruzhick authored
This cam seems to return different values on long commands, so make status check in sn9c2028_long_command() more tolerant. Anyway, read value isn't used anywhere later. Signed-off-by:
-
Geert Uytterhoeven authored
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer functionality only, can still be compiled if GPIOLIB is not enabled. Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where appropriate. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Florian Echtler authored
When stop_streaming is called while a frame is currently being retrieved, the buffer being filled will still be returned with BUF_STATE_DONE. By resetting the sequence number and checking before returning the buffer, it can now correctly be returned with BUF_STATE_ERROR. Signed-off-by:
Martin Kaltenbrunner <modin@yuri.at> Signed-off-by:
Florian Echtler <floe@butterbrot.org> Signed-off-by:
-
Florian Echtler authored
Add dev_dbg statements for easier future debugging; also change the warning about packet ID mismatches to debug output to avoid flooding the logs. This warning is only important in a very specific/rare use case when trying to correlate input events with video data. Signed-off-by:
-
Florian Echtler authored
Add missing functions to query the single fixed frame size (960x540) and supported frame rates. Technically, the SUR40 supports any arbitrary frame rate up to 60 FPS, as it is polled and not interrupt-driven. For now, we just report 30 and 60 FPS, which is sufficient to make most V4L2 tools work. Signed-off-by:
-
Florian Echtler authored
The SUR40 hardware can deliver images at up to 60 FPS; at full USB2 bandwidth, one raw frame will take about 11 ms to transmit. If the poll interval is above 5 ms, fully handling one frame will take longer than 16 ms and the overall frame rate will drop below 60 FPS. To get the full frame rate without blocking all the time and still allowing for a bit of timing jitter, we reduce the poll interval to 4 ms. Signed-off-by:
-
Antti Palosaari authored
U8 and U16LE format human readable names were translated with string containing emulated word. These strings were taken from msi2500 driver, where those formats were emulated (after module parameter is set). But on API correct names should be used, without any special case notes. Signed-off-by:
-
Antti Palosaari authored
Add complex unsigned 8-bit sample format for SDR capture. Signed-off-by:
-
Hans Verkuil authored
Use these defines instead of hardcoding this in any driver that needs it. Signed-off-by:
-
Hans Verkuil authored
The mapping of COLORSPACE_DEFAULT, YCBCR_ENC_DEFAULT or QUANTIZATION_DEFAULT to proper non-default values is fairly complex, and it is something that needs to be done both in the kernel and in userspace. So add macros that can do this conversion, making this available to both kernel and userspace. Signed-off-by:
-
Hans Verkuil authored
Document this new colorspace define. Signed-off-by:
-
Hans Verkuil authored
V4L2_COLORSPACE_RAW is added for raw image formats where the picture is minimally processed and is in the internal colorspace of the sensor. This is typically used in digital cameras where the image processing is done later. Signed-off-by:
-
Hans Verkuil authored
Document this new colorspace define. Signed-off-by:
-
Hans Verkuil authored
V4L2_COLORSPACE_DEFAULT is added so we have a specific define for the default case where applications do not set it but leave it to 0. In that case the driver will set the colorspace based on what it captures. This is already used, but we never had a define for the value 0. Signed-off-by:
-
Hans Verkuil authored
The log_status ioctl should report if the audio input has mode Bilingual. However, the check against the itv->dualwatch_stereo_mode is completely wrong and is a left-over from the distant past. Not only is the bitmask obviously wrong, the test itself is broken too since itv->dualwatch_stereo_mode is no longer a bitmask at all. Fix this code properly. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Hans Verkuil authored
This format was added but not documented. Do this now. Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by:
-
