Pull MFD changes from Samuel Ortiz:
 - 4 new drivers: Freescale i.MX on-chip Anatop, Ricoh's RC5T583 and
   TI's TPS65090 and TPS65217.
 - New variants support (8420, 8520 ab9540), cleanups and bug fixes for
   the abx500 and db8500 ST-E chipsets.
 - Some minor fixes and update for the wm8994 from Mark.
 - The beginning of a long term TWL cleanup effort coming from the TI
   folks.
 - Various fixes and cleanups for the s5m, TPS659xx, pm860x, and MAX8997
   drivers.

Fix up trivial conflicts due to duplicate patches and header file
cleanups (<linux/device.h> removal etc).

* tag 'mfd_3.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (97 commits)
  gpio/twl: Add DT support to gpio-twl4030 driver
  gpio/twl: Allocate irq_desc dynamically for SPARSE_IRQ support
  mfd: Detach twl6040 from the pmic mfd driver
  mfd: Replace twl-* pr_ macros by the dev_ equivalent and do various cleanups
  mfd: Micro-optimization on twl4030 IRQ handler
  mfd: Make twl4030 SIH SPARSE_IRQ capable
  mfd: Move twl-core IRQ allocation into twl[4030|6030]-irq files
  mfd: Remove references already defineid in header file from twl-core
  mfd: Remove unneeded header from twl-core
  mfd: Make twl-core not depend on pdata->irq_base/end
  ARM: OMAP2+: board-omap4-*: Do not use anymore TWL6030_IRQ_BASE in board files
  mfd: Return twl6030_mmc_card_detect IRQ for board setup
  Revert "mfd: Add platform data for MAX8997 haptic driver"
  mfd: Add support for TPS65090
  mfd: Add some da9052-i2c section annotations
  mfd: Build rtc5t583 only if I2C config is selected to y.
  mfd: Add anatop mfd driver
  mfd: Fix compilation error in tps65910.h
  mfd: Add 8420 variant to db8500-prcmu
  mfd: Add 8520 PRCMU variant to db8500-prcmu
  ...

Pull watchdog updates from Wim Van Sebroeck:
 - Removal of the Documentation/watchdog/00-INDEX file
 - Fix boot status reporting for imx2_wdt
 - clean-up sp805_wdt, pnx4008_wdt and mpcore_wdt
 - convert printk in watchdog drivers to pr_ functions
 - change nowayout module parameter to bool for every watchdog device
 - conversion of jz4740_wdt, pnx4008_wdt, max63xx_wdt, softdog,
   ep93xx_wdt, coh901327 and txx9wdt to new watchdog API
 - Add support for the WDIOC_GETTIMELEFT ioctl call to the new watchdog
   API
 - Change the new watchdog API so that the driver updates the timeout
   value
 - two fixes for the xen_wdt driver

Fix up conflicts in ep93xx driver due to the same patches being merged
through separate branches.

* git://www.linux-watchdog.org/linux-watchdog: (33 commits)
  watchdog: txx9wdt: fix timeout
  watchdog: Convert txx9wdt driver to watchdog framework
  watchdog: coh901327_wdt.c: fix timeout
  watchdog: coh901327: convert to use watchdog core
  watchdog: Add support for WDIOC_GETTIMELEFT IOCTL in watchdog core
  watchdog: ep93xx_wdt: timeout is an unsigned int value.
  watchdog: ep93xx_wdt: Fix timeout after conversion to watchdog core
  watchdog: Convert ep93xx driver to watchdog core
  watchdog: sp805: Use devm routines
  watchdog: sp805: replace readl/writel with lighter _relaxed variants
  watchdog: sp805: Fix documentation style comment
  watchdog: mpcore_wdt: Allow platform_get_irq() to fail
  watchdog: mpcore_wdt: Use devm routines
  watchdog: mpcore_wdt: Rename dev to pdev for pointing to struct platform_device
  watchdog: xen: don't clear is_active when xen_wdt_stop() failed
  watchdog: xen: don't unconditionally enable the watchdog during resume
  watchdog: fix compiler error for missing parenthesis
  watchdog: ep93xx_wdt.c: fix platform probe
  watchdog: ep93xx: Convert the watchdog driver into a platform device.
  watchdog: fix set_timeout operations
  ...

Pull device-mapper changes for 3.4 from Alasdair Kergon:

 - Update thin provisioning to support read-only external snapshot
   origins and discards.
 - A new target, dm verity, for device content validation.
 - Mark dm uevent and dm raid as no-longer-experimental.
 - Miscellaneous other fixes and clean-ups.

* tag 'dm-3.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: (27 commits)
  dm: add verity target
  dm bufio: prefetch
  dm thin: add pool target flags to control discard
  dm thin: support discards
  dm thin: prepare to support discard
  dm thin: use dm_target_offset
  dm thin: support read only external snapshot origins
  dm thin: relax hard limit on the maximum size of a metadata device
  dm persistent data: remove space map ref_count entries if redundant
  dm thin: commit outstanding data every second
  dm: reject trailing characters in sccanf input
  dm raid: handle failed devices during start up
  dm thin metadata: pass correct space map to dm_sm_root_size
  dm persistent data: remove redundant value_size arg from value_ptr
  dm mpath: detect invalid map_context
  dm: clear bi_end_io on remapping failure
  dm table: simplify call to free_devices
  dm thin: correct comments
  dm raid: no longer experimental
  dm uevent: no longer experimental
  ...

Pull drm fixes from Dave Airlie:
 "gma500 build fix + some regression fixes for nouveau/radeon"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: Only warn if the intra-domain offset actually exceeds the limit.
  drm/radeon/kms: add htile support to the cs checker v3
  drm/radeon/kms/atom: force bpc to 8 for now
  drm/nouveau/i2c: fix thinko/regression on really old chipsets
  drm/nouveau: default to 8bpc for non-LVDS panels if EDID isn't useful
  drm/nouveau: fix thinko causing init to fail on cards without accel
  gma500: medfield: fix build without CONFIG_BACKLIGHT_CLASS_DEVICE

Pull "drivers/clk: common clock framework" from Olof Johansson:
 "This branch contains patches from Mike Turquette adding a common clock
  framework to be shared across platforms.  This is part of the work
  towards building a common zImage for several ARM platforms."

* tag 'common-clk-api' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  clk: make CONFIG_COMMON_CLK invisible
  clk: basic clock hardware types
  clk: introduce the common clock framework
  Documentation: common clk API

Pull "ARM: More device tree support updates" from Olof Johansson:
 "This branch contains a number of updates for device tree support on
  several ARM platforms, in particular:

   * AT91 continues the device tree conversion adding support for a
     number of on-chip drivers and other functionality
   * ux500 adds probing of some of the core SoC blocks through device
     tree
   * Initial device tree support for ST SPEAr600 platforms
   * kirkwood continues the conversion to device-tree probing"

Manually merge arch/arm/mach-ux500/Kconfig due to MACH_U8500 rename, and
drivers/usb/gadget/at91_udc.c due to header file include cleanups.

Also do an "evil merge" for the MACH_U8500 config option rename that the
affected RMI4 touchscreen driver in staging.  It's called MACH_MOP500
now, and it was missed during previous merges.

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
  ARM: SPEAr600: Add device-tree support to SPEAr600 boards
  ARM: ux500: Provide local timer support for Device Tree
  ARM: ux500: Enable PL022 SSP Controller in Device Tree
  ARM: ux500: Enable PL310 Level 2 Cache Controller in Device Tree
  ARM: ux500: Enable PL011 AMBA UART Controller for Device Tree
  ARM: ux500: Enable Cortex-A9 GIC (Generic Interrupt Controller) in Device Tree
  ARM: ux500: db8500: list most devices in the snowball device tree
  ARM: ux500: split dts file for snowball into generic part
  ARM: ux500: combine the board init functions for DT boot
  ARM: ux500: Initial Device Tree support for Snowball
  ARM: ux500: CONFIG: Enable Device Tree support for future endeavours
  ARM: kirkwood: use devicetree for rtc-mv
  ARM: kirkwood: rtc-mv devicetree bindings
  ARM: kirkwood: fdt: define uart[01] as disabled, enable uart0
  ARM: kirkwood: fdt: facilitate new boards during fdt migration
  ARM: kirkwood: fdt: absorb kirkwood_init()
  ARM: kirkwood: fdt: use mrvl ticker symbol
  ARM: orion: wdt: use resource vice direct access
  ARM: Kirkwood: Remove tclk from kirkwood_asoc_platform_data.
  ARM: orion: spi: remove enable_clock_fix which is not used
  ...

Pull "ARM: More SoC support updates" from Olof Johansson:
 "This branch contains a handful of updates of SoC base code that had
  dependencies on other external trees that have now been merged:

   * Support for the new EXYNOS5250 SoC from Samsung
   * SMP and power domain support for Tegra3 from NVIDIA
   * ux500 updates for exporting SoC information through sysfs"

Fix up trivial merge conflicts as per Olof.

* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
  ARM: mach-shmobile: ap4evb: Reserve DMA memory for the frame buffer
  ARM: EXYNOS: Fix compilation error with mach-exynos4-dt board
  ARM: dts: add initial dts file for EXYNOS5250, SMDK5250
  ARM: EXYNOS: add support device tree enabled board file for EXYNOS5
  ARM: EXYNOS: add support ARCH_EXYNOS5 for EXYNOS5 SoCs
  ARM: EXYNOS: add support get_core_count() for EXYNOS5250
  ARM: EXYNOS: support EINT for EXYNOS4 and EXYNOS5
  ARM: EXYNOS: add interrupt definitions for EXYNOS5250
  ARM: EXYNOS: add support for EXYNOS5250 SoC
  ARM: EXYNOS: add support uart for EXYNOS4 and EXYNOS5
  ARM: EXYNOS: add initial setup-i2c0 for EXYNOS5
  ARM: EXYNOS: add clock part for EXYNOS5250 SoC
  ARM: EXYNOS: use exynos_init_uarts() instead of exynos4_init_uarts()
  ARM: EXYNOS: to declare static for mach-exynos/common.c
  ARM: EXYNOS: Add clkdev lookup entry for lcd clock
  ARM: dt: Explicitly configure all serial ports on Tegra Cardhu
  ARM: tegra: support for secondary cores on Tegra30
  ARM: tegra: support for Tegra30 CPU powerdomains
  ARM: tegra: add support for Tegra30 powerdomains
  ARM: tegra: export tegra_powergate_is_powered()
  ...

Pull "ARM: More SoC driver updates" from Olof Johansson:
 "This branch contains a handful of driver updates, mostly to the
  LPC32xx platform but also for Samsung EXYNOS and Davinci.

  It had a few context conflicts against patches already merged through
  fixes-non-critical.  We should have resolved this early during the
  development cycle by pulling them in as a dependency, instead I did it
  after the fact this time."

* tag 'drivers2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  gpio/samsung: use ioremap() for EXYNOS4 GPIOlib
  gpio/samsung: add support GPIOlib for EXYNOS5250
  ARM: EXYNOS: add support GPIO for EXYNOS5250
  ARM: LPC32xx: Ethernet support
  ARM: LPC32xx: USB Support
  ARM: davinci: dm644x evm: add support for VPBE display
  ARM: davinci: dm644x: add support for v4l2 video display
  ARM: EXYNOS: Hook up JPEG PD to generic PD infrastructure
  ARM: EXYNOS: Hook up G2D PD to generic PD infrastructure
  arm: lpc32xx: phy3250: add rtc & touch device
  ARM: LPC32xx: clock.c: Clock registration fixes
  ARM: LPC32xx: clock.c: jiffies wrapping
  ARM: LPC32xx: clock.c: Missing header file
  ARM: LPC32XX: Remove broken non-static declaration
  ARM: LPC32xx: clock.c: Fix mutex lock issues
  ARM: LPC32xx: clock.c: warning fix
  ARM: LPC32xx: Added lpc32xx_defconfig

This device-mapper target creates a read-only device that transparently
validates the data on one underlying device against a pre-generated tree
of cryptographic checksums stored on a second device.

Two checksum device formats are supported: version 0 which is already
shipping in Chromium OS and version 1 which incorporates some
improvements.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Signed-off-by: Will Drewry <wad@chromium.org>
Signed-off-by: Elly Jones <ellyjones@chromium.org>
Cc: Milan Broz <mbroz@redhat.com>
Cc: Olof Johansson <olofj@chromium.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

This patch introduces a new function dm_bufio_prefetch. It prefetches
the specified range of blocks into dm-bufio cache without waiting
for i/o completion.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Add dm thin target arguments to control discard support.

ignore_discard: Disables discard support

no_discard_passdown: Don't pass discards down to the underlying data
device, but just remove the mapping within the thin provisioning target.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Support discards in the thin target.

On discard the corresponding mapping(s) are removed from the thin
device.  If the associated block(s) are no longer shared the discard
is passed to the underlying device.

All bios other than discards now have an associated deferred_entry
that is saved to the 'all_io_entry' in endio_hook.  When non-discard
IO completes and associated mappings are quiesced any discards that
were deferred, via ds_add_work() in process_discard(), will be queued
for processing by the worker thread.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

drivers/md/dm-thin.c |  173 ++++++++++++++++++++++++++++++++++++++++++++++----
 drivers/md/dm-thin.c |  172 ++++++++++++++++++++++++++++++++++++++++++++++-----
 1 file changed, 158 insertions(+), 14 deletions(-)

This patch contains the ground work needed for dm-thin to support discard.

  - Adds endio function that replaces shared_read_endio.

  - Introduce an explicit 'quiesced' flag into the new_mapping structure.
    Before, this was implicitly indicated by m->list being empty.

  - The map_info->ptr remains constant for the duration of a bio's trip
    through the thin target.  Make it easier to reason about it.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Use dm_target_offset wrapper instead of referencing the awkward ti->begin
explicitly.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Support the use of an external _read only_ device as an origin for a thin
device.

Any read to an unprovisioned area of the thin device will be passed
through to the origin.  Writes trigger allocation of new blocks as
usual.

One possible use case for this would be VM hosts that want to run
guests on thinly-provisioned volumes but have the base image on another
device (possibly shared between many VMs).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

The thin metadata format can only make use of a device that is <=
THIN_METADATA_MAX_SECTORS (currently 15.9375 GB).  Therefore, there is no
practical benefit to using a larger device.

However, it may be that other factors impose a certain granularity for
the space that is allocated to a device (E.g. lvm2 can impose a coarse
granularity through the use of large, >= 1 GB, physical extents).

Rather than reject a larger metadata device, during thin-pool device
construction, switch to allowing it but issue a warning if a device
larger than THIN_METADATA_MAX_SECTORS_WARNING (16 GB) is
provided.  Any space over 15.9375 GB will not be used.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Save space by removing entries from the space map ref_count tree if
they're no longer needed.

Ref counts are stored in two places: a bitmap if the ref_count is
below 3, or a btree of uint32_t if 3 or above.

When a ref_count that was above 3 drops below we can remove it from
the tree and save some metadata space.  This removal was commented out
before because I was unsure why this was causing under-populated btree
nodes.  Earlier patches have fixed this issue.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Commit unwritten data every second to prevent too much building up.

Released blocks don't become available until after the next commit
(for crash resilience).  Prior to this patch commits were only
triggered by a message to the target or a REQ_{FLUSH,FUA} bio.  This
allowed far too big a position to build up.

The interval is hard-coded to 1 second.  This is a sensible setting.
I'm not making this user configurable, since there isn't much to be
gained by tweaking this - and a lot lost by setting it far too high.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Device mapper uses sscanf to convert arguments to numbers. The problem is that
the way we use it ignores additional unmatched characters in the scanned string.

For example, this `if (sscanf(string, "%d", &number) == 1)' will match a number,
but also it will match number with some garbage appended, like "123abc".

As a result, device mapper accepts garbage after some numbers. For example
the command `dmsetup create vg1-new --table "0 16384 linear 254:1bla 34816bla"'
will pass without an error.

This patch fixes all sscanf uses in device mapper. It appends "%c" with
a pointer to a dummy character variable to every sscanf statement.

The construct `if (sscanf(string, "%d%c", &number, &dummy) == 1)' succeeds
only if string is a null-terminated number (optionally preceded by some
whitespace characters). If there is some character appended after the number,
sscanf matches "%c", writes the character to the dummy variable and returns 2.
We check the return value for 1 and consequently reject numbers with some
garbage appended.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

The dm-raid code currently fails to create a RAID array if any of the
superblocks cannot be read.  This was an oversight as there is already
code to handle this case if the values ('- -') were provided for the
failed array position.

With this patch, if a superblock cannot be read, the array position's
fields are initialized as though '- -' was set in the table.  That is,
the device is failed and the position should not be used, but if there
is sufficient redundancy, the array should still be activated.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Fix a harmless typo.

The root is a chunk of data that gets written to the superblock.  This
data is used to recreate the space map when opening a metadata area.
We have two space maps; one tracking space on the metadata device and
one of the data device.  Both of these use the same format for their
root, so this typo was harmless.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Now that the value_size is held within every node of the btrees we can
remove this argument from value_ptr().

For the last few months a BUG_ON has been checking this argument is
the same as that held in the node.  No issues were reported.  So this
is a safe change.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

The map_context pointer should always be set. However, we have reports
that upon requeuing it is not set correctly.  So add set and clear
functions with a BUG_ON() to track the issue properly.
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

As a precaution, set bi_end_io to NULL when failing to remap.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

free_devices in dm_table.c already uses list_for_each(), so we don't
need to check if the list is empty.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Remove documentation for unimplemented 'trim' message.

I'd planned a 'trim' target message for shrinking thin devices, but
this is better handled via the discard ioctl.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

The dm raid module (using md) is becoming the preferred way of creating long-lived
mirrors through userspace LVM so remove the EXPERIMENTAL tag.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Drop EXPERIMENTAL tag from dm-uevent.

It's not changed for a while and some userspace tools are relying upon it.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Update device-mapper MAINTAINERS entry to mention quilt working tree location
and persistent-data subdirectory.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Describe attributes provided by device-mapper in /sys/block.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

When we remove an entry from a node we sometimes rebalance with it's
two neighbours.  This wasn't being done correctly; in some cases
entries have to move all the way from the right neighbour to the left
neighbour, or vice versa.  This patch pretty much re-writes the
balancing code to fix it.

This code is barely used currently; only when you delete a thin
device, and then only if you have hundreds of them in the same pool.
Once we have discard support, which removes mappings, this will be used
much more heavily.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Avoid using the bi_next field for the holder of a cell when deferring
bios because a stacked device below might change it.  Store the
holder in a new field in struct cell instead.

When a cell is created, the bio that triggered creation (the holder) was
added to the same bio list as subsequent bios.  In some cases we pass
this holder bio directly to devices underneath.  If those devices use
the bi_next field there will be trouble...

This also simplifies some code that had to work out which bio was the
holder.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Always set io->error to -EIO when an error is detected in dm-crypt.

There were cases where an error code would be set only if we finish
processing the last sector. If there were other encryption operations in
flight, the error would be ignored and bio would be returned with
success as if no error happened.

This bug is present in kcryptd_crypt_write_convert, kcryptd_crypt_read_convert
and kcryptd_async_done.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Reviewed-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

This patch fixes a possible deadlock in dm-crypt's mempool use.

Currently, dm-crypt reserves a mempool of MIN_BIO_PAGES reserved pages.
It allocates first MIN_BIO_PAGES with non-failing allocation (the allocation
cannot fail and waits until the mempool is refilled). Further pages are
allocated with different gfp flags that allow failing.

Because allocations may be done in parallel, this code can deadlock. Example:
There are two processes, each tries to allocate MIN_BIO_PAGES and the processes
run simultaneously.
It may end up in a situation where each process allocates (MIN_BIO_PAGES / 2)
pages. The mempool is exhausted. Each process waits for more pages to be freed
to the mempool, which never happens.

To avoid this deadlock scenario, this patch changes the code so that only
the first page is allocated with non-failing gfp mask. Allocation of further
pages may fail.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Call the correct exit function on failure in dm_exception_store_init.
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Pull trivial writeback fixes from Wu Fengguang:
 "They've been tested in linux-next for 20 days actually."

* tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
  writeback: Remove outdated comment
  fs: Remove bogus wait in write_inode_now()

Pull ext4 updates for 3.4 from Ted Ts'o:
 "Ext4 commits for 3.3 merge window; mostly cleanups and bug fixes

  The changes to export dirty_writeback_interval are from Artem's s_dirt
  cleanup patch series.  The same is true of the change to remove the
  s_dirt helper functions which never got used by anyone in-tree.  I've
  run these changes by Al Viro, and am carrying them so that Artem can
  more easily fix up the rest of the file systems during the next merge
  window.  (Originally we had hopped to remove the use of s_dirt from
  ext4 during this merge window, but his patches had some bugs, so I
  ultimately ended dropping them from the ext4 tree.)"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (66 commits)
  vfs: remove unused superblock helpers
  mm: export dirty_writeback_interval
  ext4: remove useless s_dirt assignment
  ext4: write superblock only once on unmount
  ext4: do not mark superblock as dirty unnecessarily
  ext4: correct ext4_punch_hole return codes
  ext4: remove restrictive checks for EOFBLOCKS_FL
  ext4: always set then trimmed blocks count into len
  ext4: fix trimmed block count accunting
  ext4: fix start and len arguments handling in ext4_trim_fs()
  ext4: update s_free_{inodes,blocks}_count during online resize
  ext4: change some printk() calls to use ext4_msg() instead
  ext4: avoid output message interleaving in ext4_error_<foo>()
  ext4: remove trailing newlines from ext4_msg() and ext4_error() messages
  ext4: add no_printk argument validation, fix fallout
  ext4: remove redundant "EXT4-fs: " from uses of ext4_msg
  ext4: give more helpful error message in ext4_ext_rm_leaf()
  ext4: remove unused code from ext4_ext_map_blocks()
  ext4: rewrite punch hole to use ext4_ext_remove_space()
  jbd2: cleanup journal tail after transaction commit
  ...

Pull Ceph updates for 3.4-rc1 from Sage Weil:
 "Alex has been busy.  There are a range of rbd and libceph cleanups,
  especially surrounding device setup and teardown, and a few critical
  fixes in that code.  There are more cleanups in the messenger code,
  virtual xattrs, a fix for CRC calculation/checks, and lots of other
  miscellaneous stuff.

  There's a patch from Amon Ott to make inos behave a bit better on
  32-bit boxes, some decode check fixes from Xi Wang, and network
  throttling fix from Jim Schutt, and a couple RBD fixes from Josh
  Durgin.

  No new functionality, just a lot of cleanup and bug fixing."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (65 commits)
  rbd: move snap_rwsem to the device, rename to header_rwsem
  ceph: fix three bugs, two in ceph_vxattrcb_file_layout()
  libceph: isolate kmap() call in write_partial_msg_pages()
  libceph: rename "page_shift" variable to something sensible
  libceph: get rid of zero_page_address
  libceph: only call kernel_sendpage() via helper
  libceph: use kernel_sendpage() for sending zeroes
  libceph: fix inverted crc option logic
  libceph: some simple changes
  libceph: small refactor in write_partial_kvec()
  libceph: do crc calculations outside loop
  libceph: separate CRC calculation from byte swapping
  libceph: use "do" in CRC-related Boolean variables
  ceph: ensure Boolean options support both senses
  libceph: a few small changes
  libceph: make ceph_tcp_connect() return int
  libceph: encapsulate some messenger cleanup code
  libceph: make ceph_msgr_wq private
  libceph: encapsulate connection kvec operations
  libceph: move prepare_write_banner()
  ...

Pull ext3, UDF, and quota fixes from Jan Kara:
 "A couple of ext3 & UDF fixes and also one improvement in quota
  locking."

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  ext3: fix start and len arguments handling in ext3_trim_fs()
  udf: Fix deadlock in udf_release_file()
  udf: Fix file entry logicalBlocksRecorded
  udf: Fix handling of i_blocks
  quota: Make quota code not call tty layer with dqptr_sem held
  udf: Init/maintain file entry checkpoint field
  ext3: Update ctime in ext3_splice_branch() only when needed
  ext3: Don't call dquot_free_block() if we don't update anything
  udf: Remove unnecessary OOM messages

Pull 9p changes for the 3.4 merge window from Eric Van Hensbergen.

* tag 'for-linus-3.4-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: statfs should not override server f_type
  net/9p: handle flushed Tclunk/Tremove
  net/9p: don't allow Tflush to be interrupted