- 29 Mar, 2013 23 commits
-
-
Andrey Smirnov authored
This commit adds a driver that exposes all the radio related functionality of the Si476x series of chips via the V4L2 subsystem. Acked-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Andrey Smirnov authored
Add a base to be used for allocation of all the SI476X specific controls in the corresponding driver. Acked-by:
-
Andrey Smirnov authored
Add appropriate documentation for all the newly added standard controls. Based on the patch by Manjunatha Halli [1] [1] http://lists-archives.com/linux-kernel/27641303-media-update-docs-for-v4l2-fm-new-features.htmlAcked-by:
-
Andrey Smirnov authored
This commit introduces new class of standard controls V4L2_CTRL_CLASS_FM_RX. This class is intended to all controls pertaining to FM receiver chips. Also, two controls belonging to said class are added as a part of this commit: V4L2_CID_TUNE_DEEMPHASIS and V4L2_CID_RDS_RECEPTION. This patch is based on the code found in the patch by Manjunatha Halli [1] [1] http://lists-archives.com/linux-kernel/27641307-new-control-class-and-features-for-fm-rx.htmlAcked-by:
-
Andrey Smirnov authored
Change the type of V4L2_CID_TUNE_PREEMPHASIS from 'integer' to 'enum v4l2_preemphasis' Acked-by:
-
Andrey Smirnov authored
This patch adds all necessary header files and Kbuild plumbing for the core driver for Silicon Laboratories Si476x series of AM/FM tuner chips. The driver as a whole is implemented as an MFD device and this patch adds a core portion of it that provides all the necessary functionality to the two other drivers that represent radio and audio codec subsystems of the chip. Acked-by:
Sam Ravnborg <sam@ravnborg.org> Signed-off-by:
-
Andrey Smirnov authored
This patch adds code related to manipulation of the properties of SI476X chips. Acked-by:
-
Andrey Smirnov authored
This patch adds main part(out of three) of the I2C driver for the "core" of MFD device. Acked-by:
-
Andrey Smirnov authored
This patch adds all the functions used for exchanging commands with the chip. Acked-by:
-
Hans Verkuil authored
On powerpc the maximum size for the ioctl argument is 8191, and it was 8192. However, the 64x64 array of threshold values is more than is actually needed in practice for PAL and NTSC formats. A 45x45 array will do just fine. So change the size accordingly to fix this problem. Signed-off-by:
-
Alexey Klimov authored
If i run verbose v4l2-compliance with my radio-mr800 device few times then i get warning about frequency out of range: root@machine:~# v4l2-compliance -r /dev/radio0 -v 2 is radio Driver Info: Driver name : radio-mr800 Card type : AverMedia MR 800 USB FM Radio Bus info : usb-0000:00:1a.0-1.2 Driver version: 3.9.0 Capabilities : 0x80050400 Tuner Radio Device Capabilities Device Caps : 0x00050400 Tuner Radio Compliance test for device /dev/radio0 (not using libv4l2): Required ioctls: test VIDIOC_QUERYCAP: OK Allow for multiple opens: test second radio open: OK test VIDIOC_QUERYCAP: OK test VIDIOC_G/S_PRIORITY: OK Debug ioctls: test VIDIOC_DBG_G_CHIP_IDENT: OK (Not Supported) test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported) test VIDIOC_LOG_STATUS: OK Input ioctls: test VIDIOC_G/S_TUNER: OK warn: v4l2-test-input-output.cpp(234): returned tuner 0 frequency out of range (6550200 not in [1400000...1728000]) test VIDIOC_G/S_FREQUENCY: OK test VIDIOC_S_HW_FREQ_SEEK: OK test VIDIOC_ENUMAUDIO: OK (Not Supported) test VIDIOC_G/S/ENUMINPUT: OK (Not Supported) test VIDIOC_G/S_AUDIO: OK (Not Supported) Inputs: 0 Audio Inputs: 0 Tuners: 1 Output ioctls: test VIDIOC_G/S_MODULATOR: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK test VIDIOC_ENUMAUDOUT: OK (Not Supported) test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) test VIDIOC_G/S_AUDOUT: OK (Not Supported) Outputs: 0 Audio Outputs: 0 Modulators: 0 Control ioctls: info: checking v4l2_queryctrl of control 'User Controls' (0x00980001) info: checking v4l2_queryctrl of control 'Mute' (0x00980909) info: checking v4l2_queryctrl of control 'Mute' (0x00980909) test VIDIOC_QUERYCTRL/MENU: OK info: checking control 'User Controls' (0x00980001) info: checking control 'Mute' (0x00980909) test VIDIOC_G/S_CTRL: OK info: checking extended control 'User Controls' (0x00980001) info: checking extended control 'Mute' (0x00980909) test VIDIOC_G/S/TRY_EXT_CTRLS: OK info: checking control event 'User Controls' (0x00980001) info: checking control event 'Mute' (0x00980909) test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) Standard Controls: 2 Private Controls: 0 Input/Output configuration ioctls: test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) test VIDIOC_ENUM/G/S/QUERY_DV_PRESETS: OK (Not Supported) test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) Format ioctls: test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported) test VIDIOC_G/S_PARM: OK (Not Supported) test VIDIOC_G_FBUF: OK (Not Supported) test VIDIOC_G_FMT: OK (Not Supported) test VIDIOC_TRY_FMT: OK (Not Supported) test VIDIOC_S_FMT: OK (Not Supported) test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) Codec ioctls: test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) Buffer ioctls: test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported) Total: 38, Succeeded: 38, Failed: 0, Warnings: 1 Some printk() debugging showed that vidioc_s_hw_freq_seek() setups radio->curfreq to out of range value (lines 395-396) and calls amradio_set_freq() to set this frequency on device without any out-of-range checks. Patch protects from setting up frequency on device to incorrect value moving clamp_t check inside amradio_set_freq. With this patch we can call amradio_set_freq() with out of range frequency from any place. Also put comment that sometimes radio->curfreq is set to out of range value in vidioc_s_hw_freq_seek(). Signed-off-by:
Alexey Klimov <klimov.linux@gmail.com> Acked-by:
-
Paul Bolle authored
The et61x251 driver was removed in v3.5. Remove the last references to its Kconfig macro now. Signed-off-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
-
Mauro Carvalho Chehab authored
ioctl's number is unsigned int. Fix it at vidioc_default. Signed-off-by: -
Masanari Iida authored
Correct spelling typo in staging/media/davinci Signed-off-by:
Masanari Iida <standby24x7@gmail.com> Signed-off-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
-
Frank Schaefer authored
This sensor is used by the "SpeedLink Vicious And Devine Laplace webcam" and others. It supports resolutions up to 1600x1200 (at 7-8 fps), but for resolutions higher than 640x480, further driver changes will be necessary, such as sensor output resolution switching (including further configuration changes), bridge xclk adjustment and disabling of 16 bit (12 bit) output formats at high resolutions. Image quality should also needs to be improved. Signed-off-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
-
Frank Schaefer authored
The Windows driver also probes at least two further i2c addresses (0x22 >> 1 and 0x66 >> 1). I've got some hints that they are very likely used by Samsung and Kodak sensors, which are known to be used in Empia devices, too. We havn't seen any devices using these sensors yet and don't know how to probe them properly, so leave a comment. Signed-off-by:
-
Frank Schaefer authored
OmniVision sensors are used as well in Empiatech based cameras such as the "SpeedLink Vicious And Devine Laplace" webcam (EM2765 + Omnivision OV2640). With this patch applied, OminiVision sensors with 8 bit address and register width are detected (recent models have a 16 bit address width and use different client addresses). The most commonly used sensors (including the ones listed by Empiatech) are detected properly, although there is no support for them yet. Signed-off-by:
-
Frank Schaefer authored
Other sensors like the ones from OmniVision need a different probing procedure, so it makes sense have separate functions for each manufacturer/sensor type. Signed-off-by:
-
Frank Schaefer authored
Add further Micron chip IDs to be able to identify all Micron sensors listed by Empiatech. Also probe the two alternate i2c addresses used by Micron sensors with 8 bit address and 16 bit register width. Signed-off-by:
-
Frank Schaefer authored
em28xx-cards.c is very large and the sensor/camera related code is growing, so move this code to a separate source code file em28xx-camera.c. Signed-off-by:
-
Frank Schaefer authored
Now that the board hints and the sensor initialization/configuration have been separated, em28xx_detect_sensor() is the better name for this function. Signed-off-by:
-
Frank Schaefer authored
Sensor detection and initialization/configuration are currently mixed together. This works as long as all devices with a particular sensor are working with the same board configuration. In the long run, this will be not sufficient, so separate these both steps to make the code more flexible and future proof. This also makes the code more consistent, because the initialization of the MT9V011 sensor subdevice is already separated. Signed-off-by:
-
Frank Schaefer authored
The current board hint code is mixed together with the sensor detection and initialization code. It actually selects a board depending on the detected sensor type only, with the result that 3 of the 6 webcam boards are currently dead. Separate it and move it to em28xx_hint_board() which already contains the board hints for analog capturing+TV and DVB devices. This way, we have all board hints at a common place which makes it easier to extend the code and reduces the risk of regressions. It also makes it possible again to use the boards EM2750_BOARD_DLCW_130, EM2820_BOARD_VIDEOLOGY_20K14XUSB and EM2860_BOARD_NETGMBH_CAM (using the module parameter "card"). NOTE: the current board hint logic for webcams is preserved. Not more not less. Signed-off-by:
-
- 28 Mar, 2013 7 commits
-
-
Frank Schaefer authored
Some devices without DVB support (such as the "Terratec Grabby" and "Easycap DC-60") provide isochronous DVB USB endpoints with wMaxPacketSize set to 0 bytes for all alt settings. Ignore these endpoints and avoid registering a DVB device node and loading the DVB driver extension. Signed-off-by:
Timo Teräs <timo.teras@iki.fi> Signed-off-by:
-
Laurent Pinchart authored
-ERANGE is the right error code when the value is outside of the menu range, but -EINVAL must be reported for invalid values inside the range. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
-
Frank Schaefer authored
The Windows driver writes the output resolution to registers 0x34 (width / 16) and 0x35 (height / 16) always. We don't know yet what these registers are used for. Signed-off-by:
-
Frank Schaefer authored
Streaming doesn't work with the EM2765 if bit 5 of the output format register 0x27 is set. It's actually not clear if really has to be set for the other chips, but for now let's keep it to avoid regressions and add a comment to the code. Signed-off-by:
-
Frank Schaefer authored
The em25xx/em276x/em277x/em278x frame data format is different to the one used by the em2710/em2750/em28xx chips. With the recent cleanups and reorganization of the frame data processing code it can be easily extended to support these devices. Signed-off-by:
-
Frank Schaefer authored
This chip can be found in the SpeedLink VAD Laplace webcam (1ae7:9003 and 1ae7:9004). Signed-off-by:
-
Frank Schaefer authored
The webcam "SpeedLink VAD Laplace" (em2765 + ov2640) uses a special algorithm for i2c communication with the sensor, which is connected to a second i2c bus. We don't know yet how to find out which devices support/use it. It's very likely used by all em25xx and em276x+ bridges. Tests with other em28xx chips (em2820, em2882/em2883) show, that this algorithm always succeeds there although no slave device is connected. The algorithm likely also works for real i2c client devices (OV2640 uses SCCB), because the Windows driver seems to use it for probing Samsung and Kodak sensors. Signed-off-by:
-
- 26 Mar, 2013 3 commits
-
-
Hans Verkuil authored
au8522_attach is dependent on CONFIG_DVB_AU8522_DTV, not CONFIG_DVB_AU8522. Signed-off-by:
-
Wei Yongjun authored
sizeof() when applied to a pointer typed expression gives the size of the pointer, not that of the pointed data. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by:
-
Wei Yongjun authored
Add the missing unlock before return from function af9035_ctrl_msg() in the error handling case. Signed-off-by:
Antti Palosaari <crope@iki.fi> Reviewed-by:
-
- 25 Mar, 2013 7 commits
-
-
Mauro Carvalho Chehab authored
If those callbacks fail, it should return zero, and not a random value. The previous code assumed that all drivers would only change signal strength if it succeeds, but this may not be true. Signed-off-by: -
Mauro Carvalho Chehab authored
Now that those functions are only used when the corresponding function calls are defined, we don't need to check if those function calls are present at the structure before using it. Signed-off-by: -
Mauro Carvalho Chehab authored
While the driver gets AFC from the tuner, it doesn't return it back via V4L2 API due to a mistake at the return. fix it. Signed-off-by: -
Hans Verkuil authored
If the tuner frontend does not support get_rf_strength, then don't set the has_signal callback. Ditto for get_afc. Both callbacks overwrite the signal and afc fields of struct v4l2_tuner but that should only happen if the tuner can actually detect this. If it can't, then it should leave those fields alone so other subdevices can try and detect the signal/afc. This fixes the bug where the au8522 detected a signal and then tuner-core overwrote it with 0 since the xc5000 tuner does not support get_rf_strength. Signed-off-by:
-
Hans Verkuil authored
- open/close/read and poll need to take the core lock as well. - when the tuner goes to sleep we should set std_set_in_tuner_core to 0 since the tuner loses the firmware at that time. - initialize the tuner if std_set_in_tuner_core == 0 whenever: 1) g/s_tuner, s_std or s_frequency is called 2) read or poll is called 3) streamon is called Signed-off-by:
Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by:
-
Hans Verkuil authored
After loading the module the initial video routing is not setup. Explicitly call s_input to get this right. Signed-off-by:
-
Hans Verkuil authored
Just opening a device shouldn't have any side-effects. Signed-off-by:
-
