- 21 Feb, 2017 28 commits
-
-
David S. Miller authored
Thomas Petazzoni says: ==================== net: mvpp2: misc improvements and preparation patches This series contains a number of fixes, misc improvements and preparation patches for an upcoming series that adds support for the new PPv2.2 network controller to the mvpp2 driver. The most significant improvements are: - Switching to using build_skb(), which is necessary for the upcoming PPv2.2 support, but anyway a good improvement to the current mvpp2 driver (supporting PPv2.1). - Making the driver build on 64-bit platforms. Changes since v3: - Addition of a patch "net: mvpp2: fix DMA address calculation in mvpp2_txq_inc_put()", which fixes a bug in the driver in the calculation of DMA addresses. This bug was found using DMA_API_DEBUG. - Modify the "net: mvpp2: switch to build_skb() in the RX path" patch to recalculate the fragment size when the MTU is changed in mvpp2_bm_update_mtu(). - Added Acked-by from Russell King on all patches, except: * "net: mvpp2: fix DMA address calculation in mvpp2_txq_inc_put()", because it's a new patch * "net: mvpp2: switch to build_skb() in the RX path" because I modified it since the v3. - Rebased on top of 4.10. Changes since v2: - Fix remaining 64-bit build warning, reported by David Miller. - Adjust how bit mask related definitions are done in "net: mvpp2: simplify MVPP2_PRS_RI_* definitions" according to Russell King suggestions. - Add a patch "net: mvpp2: remove useless arguments in mvpp2_rx_{pkts,time}_coal_set", suggested by Russell King. - Rework mvpp2_rx_time_coal_set() implementation to avoid overflows and rounding errors. I've used the implementation suggested by Russell King. Changes since v1: - This series is split as a separate series from the larger patch set adding support for PPv2.2 in the mvpp2 driver, as requested by David Miller. - Rebased on top of v4.10-rc1. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Thomas Petazzoni authored
The mvpp2 is going to be extended to support the Marvell Armada 7K/8K platform, which is ARM64. As a preparation to this work, this commit enables building the mvpp2 driver on ARM64, by: - Adjusting the Kconfig dependency - Fixing the types used in the driver so that they are 32/64-bits compliant. We use dma_addr_t for DMA addresses, and unsigned long for virtual addresses. It is worth mentioning that after this commit, the driver is for now still only used on 32-bits platforms, and will only work on 32-bits platforms. Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Thomas Petazzoni authored
This commit adapts the mvpp2 RX path to use the build_skb() method. Not only build_skb() is now the recommended mechanism, but it also simplifies the addition of support for the PPv2.2 variant. Indeed, without build_skb(), we have to keep track for each RX descriptor of the physical address of the packet buffer, and the virtual address of the SKB. However, in PPv2.2 running on 64 bits platform, there is not enough space in the descriptor to store the virtual address of the SKB. So having to take care only of the address of the packet buffer, and building the SKB upon reception helps in supporting PPv2.2. The implementation is fairly straightforward: - mvpp2_skb_alloc() is renamed to mvpp2_buf_alloc() and no longer allocates a SKB. Instead, it allocates a buffer using the new mvpp2_frag_alloc() function, with enough space for the data and SKB. - The initialization of the RX buffers in mvpp2_bm_bufs_add() as well as the refill of the RX buffers in mvpp2_rx_refill() is adjusted accordingly. - Finally, the mvpp2_rx() is modified to use build_skb(). Signed-off-by:
-
Thomas Petazzoni authored
Some of the MVPP2_PRS_RI_* definitions use the ~(value) syntax, which doesn't compile nicely on 64-bit. Moreover, those definitions are in fact unneeded, since they are always used in combination with a bit mask that ensures only the appropriate bits are modified. Therefore, such definitions should just be set to 0x0. In addition, as suggested by Russell King, we change the _MASK definitions to also use the BIT() macro so that it is clear they are related to the values defined afterwards. For example: #define MVPP2_PRS_RI_L2_CAST_MASK 0x600 #define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10)) #define MVPP2_PRS_RI_L2_MCAST BIT(9) #define MVPP2_PRS_RI_L2_BCAST BIT(10) becomes #define MVPP2_PRS_RI_L2_CAST_MASK (BIT(9) | BIT(10)) #define MVPP2_PRS_RI_L2_UCAST 0x0 #define MVPP2_PRS_RI_L2_MCAST BIT(9) #define MVPP2_PRS_RI_L2_BCAST BIT(10) Because the values (MVPP2_PRS_RI_L2_UCAST, MVPP2_PRS_RI_L2_MCAST and MVPP2_PRS_RI_L2_BCAST) are always applied with MVPP2_PRS_RI_L2_CAST_MASK, and therefore there is no need for MVPP2_PRS_RI_L2_UCAST to be defined as ~(BIT(9) | BIT(10)). It fixes the following warnings when building the driver on a 64-bit platform (which is not possible as of this commit, but will be enabled in a follow-up commit): drivers/net/ethernet/marvell/mvpp2.c: In function ‘mvpp2_prs_mac_promisc_set’: drivers/net/ethernet/marvell/mvpp2.c:524:33: warning: large integer implicitly truncated to unsigned type [-Woverflow] #define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10)) ^ drivers/net/ethernet/marvell/mvpp2.c:1459:33: note: in expansion of macro ‘MVPP2_PRS_RI_L2_UCAST’ mvpp2_prs_sram_ri_update(&pe, MVPP2_PRS_RI_L2_UCAST, Signed-off-by: -
Thomas Petazzoni authored
Signed-off-by:
-
Thomas Petazzoni authored
Signed-off-by:
-
Thomas Petazzoni authored
The mvpp2_bm_bufs_add() currently creates a fake cookie by calling mvpp2_bm_cookie_pool_set(), just to be able to call mvpp2_pool_refill(). But all what mvpp2_pool_refill() does is extract the pool ID from the cookie, and call mvpp2_bm_pool_put() with this ID. Instead of doing this convoluted thing, just call mvpp2_bm_pool_put() directly, since we have the BM pool ID. Signed-off-by:
-
Thomas Petazzoni authored
This commit drops dead code from the mvpp2 driver. The 'in_use' and 'in_use_thresh' fields of 'struct mvpp2_bm_pool' are incremented/decremented/initialized in various places. But they are only used in one place: if (is_recycle && (atomic_read(&bm_pool->in_use) < bm_pool->in_use_thresh)) return 0; However 'is_recycle', passed as argument to mvpp2_rx_refill() is always false. So in fact, this code is never reached, and the 'is_recycle' argument is useless. So let's drop this code. Signed-off-by: -
Thomas Petazzoni authored
This commit remove a field of 'struct mvpp2_tx_queue' that is not used anywhere. Signed-off-by:
-
Thomas Petazzoni authored
The mvpp2_txq_bufs_free() function is called upon TX completion to DMA unmap TX buffers, and free the corresponding SKBs. It gets the references to the SKB to free and the DMA buffer to unmap from a per-CPU txq_pcpu data structure. However, the code currently increments the pointer to the next entry before doing the DMA unmap and freeing the SKB. It does not cause any visible problem because for a given SKB the TX completion is guaranteed to take place on the CPU where the TX was started. However, it is much more logical to increment the pointer to the next entry once the current entry has been completely unmapped/released. Signed-off-by:
-
Thomas Petazzoni authored
When configuring the MVPP2_ISR_RX_THRESHOLD_REG with the RX coalescing time threshold, we do not check for the maximum allowed value supported by the driver, which means we might overflow and use a bogus value. This commit adds a check for this situation, and if a value higher than what is supported by the hardware is provided, then we use the maximum value supported by the hardware. In order to achieve this in a way that avoids overflow and rounding errors, we introduce two utility functions mvpp2_usec_to_cycles() and cycles_to_usec(). Many thanks to Russell King for suggesting this implementation. Signed-off-by:
-
Thomas Petazzoni authored
Currently, mvpp2_rx_pkts_coal_set() does the following to avoid setting a too large value for the RX coalescing by packet number: val = (pkts & MVPP2_OCCUPIED_THRESH_MASK); This means that if you set a value that is slightly higher the the maximum number of packets, you in fact get a very low value. It makes a lot more sense to simply check if the value is too high, and if it's too high, limit it to the maximum possible value. Signed-off-by:
-
Thomas Petazzoni authored
As noticed by Russell King, the last argument of mvpp2_rx_{pkts,time}_coal_set() is useless, since the packet/time coalescing value is already stored in the 'struct mvpp2_rx_queue *' passed as argument to these functions. So passing the packet/time value as an additional argument, and setting them again in the mvpp2_rx_queue structure is useles. This commit therefore gets rid of this additional argument, assuming the caller has assigned the appropriate value to rxq->pkts_coal or rxq->time_coal before calling the respective functions. Signed-off-by: -
Thomas Petazzoni authored
When TX descriptors are filled in, the buffer DMA address is split between the tx_desc->buf_phys_addr field (high-order bits) and tx_desc->packet_offset field (5 low-order bits). However, when we re-calculate the DMA address from the TX descriptor in mvpp2_txq_inc_put(), we do not take tx_desc->packet_offset into account. This means that when the DMA address is not aligned on a 32 bytes boundary, we end up calling dma_unmap_single() with a DMA address that was not the one returned by dma_map_single(). This inconsistency is detected by the kernel when DMA_API_DEBUG is enabled. We fix this problem by properly calculating the DMA address in mvpp2_txq_inc_put(). Cc: <stable@vger.kernel.org> Signed-off-by:
-
Lee Ryder authored
MACSec test failed when asynchronous crypto operations is used. It encounters packet validation failed since macsec_skb_cb(skb)->valid is always 'false'. This patch adds missing "macsec_skb_cb(skb)->valid = true" in macsec_decrypt_done() when "err == 0". Signed-off-by:
Ryder Lee <ryder.lee@mediatek.com> Signed-off-by:
-
Gao Feng authored
The USEC_PER_SEC is used once in sock_set_timeout as the max value of tv_usec. But there are other similar codes which use the literal 1000000 in this file. It is minor cleanup to keep consitent. Signed-off-by:
Gao Feng <fgao@ikuai8.com> Signed-off-by:
-
Jason Wang authored
This patch switch to use build_skb() for small buffer which can have better performance for both TCP and XDP (since we can work at page before skb creation). It also remove lots of XDP codes since both mergeable and small buffer use page frag during refill now. Before | After XDP_DROP(xdp1) 64B : 11.1Mpps | 14.4Mpps Tested with xdp1/xdp2/xdp_ip_tx_tunnel and netperf. Signed-off-by:Jason Wang <jasowang@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Paolo Abeni authored
The skbs processed by ip_cmsg_recv() are not guaranteed to be linear e.g. when sending UDP packets over loopback with MSGMORE. Using csum_partial() on [potentially] the whole skb len is dangerous; instead be on the safe side and use skb_checksum(). Thanks to syzkaller team to detect the issue and provide the reproducer. v1 -> v2: - move the variable declaration in a tighter scope Fixes: ad6f939a ("ip: Add offset parameter to ip_cmsg_recv") Reported-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Roopa Prabhu authored
silences the below warning: drivers/net/vxlan.c: In function ‘neigh_reduce’: drivers/net/vxlan.c:1599:25: warning: variable ‘saddr’ set but not used [-Wunused-but-set-variable] Signed-off-by:Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by:
-
Roopa Prabhu authored
This patch adds changelink rtnl op support for vxlan netdevs. code changes involve: - refactor vxlan_newlink into vxlan_nl2conf to be used by vxlan_newlink and vxlan_changelink - vxlan_nl2conf and vxlan_dev_configure take a changelink argument to isolate changelink checks and updates. - Allow changing only a few attributes: - return -EOPNOTSUPP for attributes that cannot be changed for now. Incremental patches can make the non-supported one available in the future if needed. Signed-off-by: -
Tobias Klauser authored
There is only one possible error path which reaches the err label, so return ERR_PTR(-ENOMEM) directly if alloc_netdev_mqs() fails. This also allows to omit the err variable. Signed-off-by:
Tobias Klauser <tklauser@distanz.ch> Signed-off-by:
-
Jason Wang authored
We set queues before reset which will cause a crash[1]. This is because is_xdp_raw_buffer_queue() depends on the old xdp queue pairs number to do the correct detection. So fix this by - passing xdp queue pairs and current queue pairs to virtnet_reset() - change vi->xdp_qp after reset but before refill, to make sure both free_unused_bufs() and refill can make correct detection of XDP. - remove the duplicated queue pairs setting before virtnet_reset() since we will do it inside virtnet_reset() [1] [ 74.328168] general protection fault: 0000 [#1] SMP [ 74.328625] Modules linked in: nfsd xfs libcrc32c virtio_net virtio_pci [ 74.329117] CPU: 0 PID: 2849 Comm: xdp2 Not tainted 4.10.0-rc7+ #499 [ 74.329577] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.10.1-0-g8891697-prebuilt.qemu-project.org 04/01/2014 [ 74.330424] task: ffff88007a894000 task.stack: ffffc90004388000 [ 74.330844] RIP: 0010:skb_release_head_state+0x28/0x80 [ 74.331298] RSP: 0018:ffffc9000438b8d0 EFLAGS: 00010206 [ 74.331676] RAX: 0000000000000000 RBX: ffff88007ad96300 RCX: 0000000000000000 [ 74.332217] RDX: ffff88007fc137a8 RSI: ffff88007fc0db28 RDI: 0001bf00000001be [ 74.332758] RBP: ffffc9000438b8d8 R08: 000000000005008f R09: 00000000000005f9 [ 74.333274] R10: ffff88007d001700 R11: ffffffff820a8a4d R12: ffff88007ad96300 [ 74.333787] R13: 0000000000000002 R14: ffff880036604000 R15: 000077ff80000000 [ 74.334308] FS: 00007fc70d8a7b40(0000) GS:ffff88007fc00000(0000) knlGS:0000000000000000 [ 74.334891] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 74.335314] CR2: 00007fff4144a710 CR3: 000000007ab56000 CR4: 00000000003406f0 [ 74.335830] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 74.336373] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 74.336895] Call Trace: [ 74.337086] skb_release_all+0xd/0x30 [ 74.337356] consume_skb+0x2c/0x90 [ 74.337607] free_unused_bufs+0x1ff/0x270 [virtio_net] [ 74.337988] ? vp_synchronize_vectors+0x3b/0x60 [virtio_pci] [ 74.338398] virtnet_xdp+0x21e/0x440 [virtio_net] [ 74.338741] dev_change_xdp_fd+0x101/0x140 [ 74.339048] do_setlink+0xcf4/0xd20 [ 74.339304] ? symcmp+0xf/0x20 [ 74.339529] ? mls_level_isvalid+0x52/0x60 [ 74.339828] ? mls_range_isvalid+0x43/0x50 [ 74.340135] ? nla_parse+0xa0/0x100 [ 74.340400] rtnl_setlink+0xd4/0x120 [ 74.340664] ? cpumask_next_and+0x30/0x50 [ 74.340966] rtnetlink_rcv_msg+0x7f/0x1f0 [ 74.341259] ? sock_has_perm+0x59/0x60 [ 74.341586] ? napi_consume_skb+0xe2/0x100 [ 74.342010] ? rtnl_newlink+0x890/0x890 [ 74.342435] netlink_rcv_skb+0x92/0xb0 [ 74.342846] rtnetlink_rcv+0x23/0x30 [ 74.343277] netlink_unicast+0x162/0x210 [ 74.343677] netlink_sendmsg+0x2db/0x390 [ 74.343968] sock_sendmsg+0x33/0x40 [ 74.344233] SYSC_sendto+0xee/0x160 [ 74.344482] ? SYSC_bind+0xb0/0xe0 [ 74.344806] ? sock_alloc_file+0x92/0x110 [ 74.345106] ? fd_install+0x20/0x30 [ 74.345360] ? sock_map_fd+0x3f/0x60 [ 74.345586] SyS_sendto+0x9/0x10 [ 74.345790] entry_SYSCALL_64_fastpath+0x1a/0xa9 [ 74.346086] RIP: 0033:0x7fc70d1b8f6d [ 74.346312] RSP: 002b:00007fff4144a708 EFLAGS: 00000246 ORIG_RAX: 000000000000002c [ 74.346785] RAX: ffffffffffffffda RBX: 00000000ffffffff RCX: 00007fc70d1b8f6d [ 74.347244] RDX: 000000000000002c RSI: 00007fff4144a720 RDI: 0000000000000003 [ 74.347683] RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000 [ 74.348544] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fff4144bd90 [ 74.349082] R13: 0000000000000002 R14: 0000000000000002 R15: 00007fff4144cda0 [ 74.349607] Code: 00 00 00 55 48 89 e5 53 48 89 fb 48 8b 7f 58 48 85 ff 74 0e 40 f6 c7 01 74 3d 48 c7 43 58 00 00 00 00 48 8b 7b 68 48 85 ff 74 05 <f0> ff 0f 74 20 48 8b 43 60 48 85 c0 74 14 65 8b 15 f3 ab 8d 7e [ 74.351008] RIP: skb_release_head_state+0x28/0x80 RSP: ffffc9000438b8d0 [ 74.351625] ---[ end trace fe6e19fd11cfc80b ]--- Fixes: 2de2f7f4 ("virtio_net: XDP support for adjust_head") Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by:
-
Michael Walle authored
This commit adds the ndo_do_ioctl() callback which allows the userspace to access PHY registers, for example. This will make mii-diag and similar tools work. Signed-off-by:
Michael Walle <michael@walle.cc> Signed-off-by:
-
Philippe Reynes authored
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. As I don't have the hardware, I'd be very pleased if someone may test this patch. Signed-off-by:Philippe Reynes <tremyfr@gmail.com> Signed-off-by:
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Fix probe and open bugs. Fix 3 issues related to bnxt_init_one() and bnxt_open(). Don't probe bridge devices and fixup some error code paths. ==================== Signed-off-by: -
Sathya Perla authored
In the bnxt_init_one() failure path, bar1 and bar2 are not being unmapped. This commit fixes this issue. Reorganize the code so that bnxt_init_one()'s failure path and bnxt_remove_one() can call the same function to do the PCI cleanup. Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Michael Chan authored
If bnxt_hwrm_ring_free() is called during a failure path in bnxt_open(), it is possible that the completion rings have not been allocated yet. In that case, the completion doorbell has not been initialized, and calling bnxt_disable_int() will crash. Fix it by checking that the completion ring has been initialized before writing to the completion ring doorbell. Signed-off-by:
-
Ray Jui authored
There are additional SoC devices that use the same device ID for bridge and NIC devices. The bnxt driver should reject probe against all bridge devices since it's meant to be used with only endpoint devices. Signed-off-by:
Ray Jui <ray.jui@broadcom.com> Signed-off-by:
-
- 20 Feb, 2017 12 commits
-
-
David S. Miller authored
Yuval Mintz says: ==================== qed*: Bug fixes This is a respin of the series with same name for net-next instead of net [only patch #10 is changed]. The 3 first patches here are a repost of ("qed: RoCE infrastructure fixes"). The fourth is an additional RoCE-related infrastructure fix, and the latter contain various fixes to qed/qede. Please consider applying these to `net-next'. ==================== Signed-off-by: -
Mintz, Yuval authored
Driver changes the link properties via communication with the management firmware, and re-reads the resulting link status when it receives an indication that the link has changed. However, there are certain scenarios where such indications might be missing, and so driver also re-reads the current link results without attention in several places. Specifically, it does so during load and when resetting the link. This creates a race where driver might reflect incorrect link status - e.g., when explicit reading of the link status is switched by attention with the changed configuration. Correct this flow by a lock syncronizing the handling of the link indications [both explicit requests and attention]. Signed-off-by:
Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by:
-
Mintz, Yuval authored
Flows accessing registers require the flow to hold a PTT entry. To protect 'major' load/unload flows a main_ptt is pre-allocated to guarantee such flows wouldn't be blocked by PTT being unavailable. Status block initialization currently uses the main_ptt which is incorrect, as this flow might run concurrently to others [E.g., loading qedr while toggling qede]. That would have dire effects as it means registers' access to device breaks and further read/writes might access incorrect addresses. Instead, when initializing status blocks acquire/release a PTT as part of the flow. Signed-off-by:
-
Sudarsana Reddy Kalluru authored
Driver currently utilizes the same loop variable in two nested loops. Signed-off-by:
Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by:
-
Mintz, Yuval authored
VF learns of the current link state via its bulletin board, which might reflect either the physical link state or some user-configured logical state. Whenever the physical link changes or whnever such a configuration is explicitly made by user the PF driver would update the bulletin that the VF reads. But if neither has happened - i.e., PF still hasn't got a physical link up and no additional configuration was done the VF wouldn't have a valid link information available. Simply reflect the physical link state whenever the VF is initialized. The user could then affect it however he wants. Signed-off-by:
-
Mintz, Yuval authored
qed needs to be informed of the removal of the qede interface prior to its actual removal, as qede has some registered callbacks that might get called async to the removal flow. Signed-off-by:
-
Mintz, Yuval authored
Need to make sure the slowpath workqueue and the qede lock are ready for the registration of the netdevice, as once registered there's no guarantee those wouldn't be used. Signed-off-by:
-
Ram Amrani authored
Reserving doorbell BAR space according to the currently active CPUs may result in a bug if disabled CPUs are later enabled but no doorbell space was reserved for them. Signed-off-by:
Ram Amrani <Ram.Amrani@cavium.com> Signed-off-by:
-
Ram Amrani authored
If QP is in reset state then there are no resources to free so avoid freeing any. Signed-off-by:
-
Ram Amrani authored
Currently the state is read only after the buffers are relesed. Signed-off-by:
-
Ram Amrani authored
The CQ resource pool is protected by a spin lock. When a CQ creation fails it now deallocates under that lock as well. Signed-off-by:
-
David S. Miller authored
Pavel Belous says: ==================== net: ethernet: aquantia: improvements and fixes The following patchset contains improvements and fixes for aQuantia AQtion ethernet driver from net-next tree. Most fixes are based on the comments from Lino Sanfilippo. Sanity testing was performed on real HW. No regression found. v1->v2: 1)Removed buffers copying. 2)Fixed dma error handling. v2->v3: 1)Fixes for aq_ndev_change_mtu: -Use core MTU checking for min_mtu. -Removed extra new_mtu assigment. 2)Reverse XMAS tree in aq_ring_rx_fill. v3->v4: 1)Use ndev->reg_state instead "is_ndev_registered" flag. ==================== Signed-off-by:
-
