To read pid/cid registers, the probed device need to be properly turned on.
When it is inside a power domain, the bus code should ensure that the
given power domain is enabled before trying to access device's registers.
However in some cases power domain (or clocks) might not be yet available.
Returning -EPROBE_DEFER is not a solution in such case, because callers
don't handle this special error code. Instead such devices are added to the
special list and their registration is retried from periodic worker until
all resources are available.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

complete_all() should only be called once, doing it twice is a clear bug.

8565adbc ("drivers/misc/ti-st: fix read fw version cmd") added the
additional complete_all() call. Since we call complete_all() when
leaving the function we can drop the complete_all() call inside
true branch of the if statement.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Pavan Savoy <pavan_savoy@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's harmless but, if "enable" isn't set, then we pass uninitialized
values to qcom_coincell_chgr_config().  The values aren't used, but
let's silence the warning anyway.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tim Bird <tim.bird@sonymobile.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

According to full-history-linux commit d3794f4fa7c3edc3 ("[PATCH] M68k
update (part 25)"), port operations are allowed on m68k if CONFIG_ISA is
defined.

However, commit 153dcc54 ("[PATCH] mem driver: fix conditional
on isa i/o support") accidentally changed an "||" into an "&&",
disabling it completely on m68k. This logic was retained when
introducing the DEVPORT symbol in commit 4f911d64 ("Make
/dev/port conditional on config symbol").

Drop the bogus dependency on !M68K to fix this.

Fixes: 153dcc54 ("[PATCH] mem driver: fix conditional on isa i/o support")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Removing boot time log for drivers that don't report useful information
other than they came up properly.  The same information can be found in
sysFS once the system has booted and as such doesn't provide any value
in the boot log.
Reported-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The sysFS "status" entry conveys a wealth of information about
the status of the HW but goes agains the sysFS rule of one topic
per file.

This patch rectify the situation by adding read-only entries for
each of the field formaly displayed by "status".  The ABI
documentation is kept up to date.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Macro "coresight_simple_func()" can be used by several drivers.
As such making the structure type generic and moving to a
globally available header file.  That way individual drivers
can use the functionality by simply specifying the structure
they need to work with.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding a set of API allowing the Perf core to treat ETMv4
tracers like other PMUs.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding new mode to limit tracing to kernel or user space.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Similarly to ETMv3, moving etmv4_drvdata::enable to an atomic
type that gives the 'mode' of a tracer and prevents multiple,
simultanious access by different subsystems.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As with the ETMv3.x driver, calling 'smp_call_function_single()'
twice in a row is highly ineffective.  As such moving function
'etm4_os_unlock()' before the default initialisation takes
place, which results in the same outcome.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Splitting and updating the default initialisation for each etmv4
configuration so that it can be called at the beginning of each
session rather than initialisation time only.

Since the trace ID isn't expected to change with every session,
moving it with the default tracer initialisation.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Similar to what was done on etm3x, splitting driver structure
etmv4_drvdata in two.  One half is concerned with the HW
characteristics that are generally static in nature.  The other
half deals with user configuration and will change from one
trace session to another.

No gain/loss of functionality is incurred from this patch.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding new sysFS management interface to query the configuration
and the traceid registers.  Both are required to convey information
to the perf cmd line tools when using ETMv4 tracers as PMU.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As with the etm3x driver, sysFS entries are big enough to justify
their own file. As such moving all sysFS related declarations to
a dedicated location.

No gain/loss of functionality is incurred from this patch.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix a typo in the help message for the -d parameter by removing one 'm'.
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de>
Acked-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

My static checker complains that "ret" could be uninitialized at the
end, which is true but it's more likely that it would be set to zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Every new architecture has to add itself to the growing list of those
that do not support the legacy PC RTC driver.

This replaces the long list of architectures that don't support it
with a shorter list of those that do.

The list is taken from those architectures that have a non-empty
asm/mc146818rtc.h header file and were not explicitly blacklisted
or select RTC_LIB.

Alpha and Loongson64 can already choose between this driver and
an rtc-class based one. mn10300 is actually the only architecture
now that still requires this driver, and that should be fairly
easy to change to use rtc-cmos if we want to kill off rtc.ko
for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If kstrtoint() returns -ERANGE then "tmp" is uninitialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Evgeniy Polaykov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The 93xx46 driver is using spi_dev_get() apparently just to take a copy
of the SPI device used to instantiate it but never calls spi_dev_put()
to free it.  Since the device is guaranteed to exist between probe() and
remove() there should be no need for the driver to take an extra
reference to it so fix the leak by just using a straight assignment.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The at25 driver is using spi_dev_get() apparently just to take a copy
of the SPI device used to instantiate it but never calls spi_dev_put()
to free it.  Since the device is guaranteed to exist between probe() and
remove() there should be no need for the driver to take an extra
reference to it so fix the leak by just using a straight assignment.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit enables the active pullup (APU bit) by default for
the DS2482 1-Wire master.

>From the DS2482 datasheet:
"The APU bit controls whether an active pullup (controlled slew-rate
transistor) or a passive pullup (Rwpu resistor) will be used to drive
a 1-Wire line from low to high. When APU = 0, active pullup is disabled
(resistor mode). Active Pullup should always be selected unless there is
only a single slave on the 1-Wire line."

According to the module author, Ben Gardner:
"It doesn't look like active pullup would cause any hurt if there
is only a single slave."
And my tests with multiple and single slaves on 1-Wire bus
confirms that.

This active pullup can be manually disabled using the introduced
module parameter:
  active_pullup = 0
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch moves to nvmem support in the driver to use callback
instead of regmap.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch moves to nvmem support in the driver to use callback
instead of regmap.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch moves to nvmem support in the driver to use callback
instead of regmap.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch moves to nvmem support in the driver to use callback
instead of regmap.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch moves to nvmem support in the driver to use callback
instead of regmap.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch moves to nvmem support in the driver to use callback
instead of regmap.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch moves to nvmem support in the driver to use callback instead of
regmap.
Reported-by: Rajendra Nayak <rjendra@qti.qualcomm.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch moves to nvmem support in the driver to use callback instead
of regmap.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch moves to nvmem support in the driver to use callback instead
of regmap.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmem uses regmap_raw_read/write apis to read/write data from providers,
regmap raw apis stopped working with recent kernels which removed raw
accessors on mmio bus. This resulted in broken nvmem for providers
which are based on regmap mmio bus. This issue can be fixed temporarly
by moving to other regmap apis, but we might hit same issue in future.
Moving to interfaces based on read/write callbacks from providers would
be more robust.

This patch removes regmap dependency from nvmem and introduces
read/write callbacks from the providers.

Without this patch nvmem providers like qfprom based on regmap mmio
bus would not work.
Reported-by: Rajendra Nayak <rjendra@qti.qualcomm.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Consolidate vme_bridge structure setup that every bridge was required
to do itself. This came about because .irq_mtx is only used within the
VME core, but was required to be setup externally.

This returns the structure passed in to support shorthand like this:

    bridge = vme_init_bridge(&priv->bridge);
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Martyn Welch <martyn@welchs.me.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The devres.o gets linked if HAS_IOMEM is present so on ARCH=um
allyesconfig (COMPILE_TEST) failed on many files with:

drivers/built-in.o: In function `mtk_thermal_probe':
mtk_thermal.c:(.text+0x394618): undefined reference to `devm_ioremap_resource'

The users of devm_ioremap_resource() which are compile-testable should
depend on HAS_IOMEM.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix a typo in the spurious interrupt warning and consistently capitalize
VME, PCI, and DMA acronyms.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Martyn Welch <martyn@welchs.me.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lsvmbus keeps its own copy of all VMBus UUIDs, add PCIe pass-through
device there to not report 'Unknown' for such devices.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We set host_specified_ha_region = true on certain request but this is a
global state which stays 'true' forever. We need to reset it when we
receive a request where ha_region is not specified. I did not see any
real issues, the bug was found by code inspection.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When we iterate through all HA regions in handle_pg_range() we have an
assumption that all these regions are sorted in the list and the
'start_pfn >= has->end_pfn' check is enough to find the proper region.
Unfortunately it's not the case with WS2016 where host can hot-add regions
in a different order. We end up modifying the wrong HA region and crashing
later on pages online. Modify the check to make sure we found the region
we were searching for while iterating. Fix the same check in pfn_covered()
as well.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Kdump keeps biting. Turns out CHANNELMSG_UNLOAD_RESPONSE is always
delivered to the CPU which was used for initial contact or to CPU0
depending on host version. vmbus_wait_for_unload() doesn't account for
the fact that in case we're crashing on some other CPU we won't get the
CHANNELMSG_UNLOAD_RESPONSE message and our wait on the current CPU will
never end.

Do the following:
1) Check for completion_done() in the loop. In case interrupt handler is
   still alive we'll get the confirmation we need.

2) Read message pages for all CPUs message page as we're unsure where
   CHANNELMSG_UNLOAD_RESPONSE is going to be delivered to. We can race with
   still-alive interrupt handler doing the same, add cmpxchg() to
   vmbus_signal_eom() to not lose CHANNELMSG_UNLOAD_RESPONSE message.

3) Cleanup message pages on all CPUs. This is required (at least for the
   current CPU as we're clearing CPU0 messages now but we may want to bring
   up additional CPUs on crash) as new messages won't be delivered till we
   consume what's pending. On boot we'll place message pages somewhere else
   and we won't be able to read stale messages.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>