Implements supports for the Group Policy VXLAN extension [0] to provide
a lightweight and simple security label mechanism across network peers
based on VXLAN. The security context and associated metadata is mapped
to/from skb->mark. This allows further mapping to a SELinux context
using SECMARK, to implement ACLs directly with nftables, iptables, OVS,
tc, etc.

The group membership is defined by the lower 16 bits of skb->mark, the
upper 16 bits are used for flags.

SELinux allows to manage label to secure local resources. However,
distributed applications require ACLs to implemented across hosts. This
is typically achieved by matching on L2-L4 fields to identify the
original sending host and process on the receiver. On top of that,
netlabel and specifically CIPSO [1] allow to map security contexts to
universal labels.  However, netlabel and CIPSO are relatively complex.
This patch provides a lightweight alternative for overlay network
environments with a trusted underlay. No additional control protocol
is required.

           Host 1:                       Host 2:

      Group A        Group B        Group B     Group A
      +-----+   +-------------+    +-------+   +-----+
      | lxc |   | SELinux CTX |    | httpd |   | VM  |
      +--+--+   +--+----------+    +---+---+   +--+--+
	  \---+---/                     \----+---/
	      |                              |
	  +---+---+                      +---+---+
	  | vxlan |                      | vxlan |
	  +---+---+                      +---+---+
	      +------------------------------+

Backwards compatibility:
A VXLAN-GBP socket can receive standard VXLAN frames and will assign
the default group 0x0000 to such frames. A Linux VXLAN socket will
drop VXLAN-GBP  frames. The extension is therefore disabled by default
and needs to be specifically enabled:

   ip link add [...] type vxlan [...] gbp

In a mixed environment with VXLAN and VXLAN-GBP sockets, the GBP socket
must run on a separate port number.

Examples:
 iptables:
  host1# iptables -I OUTPUT -m owner --uid-owner 101 -j MARK --set-mark 0x200
  host2# iptables -I INPUT -m mark --mark 0x200 -j DROP

 OVS:
  # ovs-ofctl add-flow br0 'in_port=1,actions=load:0x200->NXM_NX_TUN_GBP_ID[],NORMAL'
  # ovs-ofctl add-flow br0 'in_port=2,tun_gbp_id=0x200,actions=drop'

[0] https://tools.ietf.org/html/draft-smith-vxlan-group-policy
[1] http://lwn.net/Articles/204905/Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/xen-netfront.c

Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Don't use uninitialized data in IPVS, from Dan Carpenter.

 2) conntrack race fixes from Pablo Neira Ayuso.

 3) Fix TX hangs with i40e, from Jesse Brandeburg.

 4) Fix budget return from poll calls in dnet and alx, from Eric
    Dumazet.

 5) Fix bugus "if (unlikely(x) < 0)" test in AF_PACKET, from Christoph
    Jaeger.

 6) Fix bug introduced by conversion to list_head in TIPC retransmit
    code, from Jon Paul Maloy.

 7) Don't use GFP_NOIO under spinlock in USB kaweth driver, from Alexey
    Khoroshilov.

 8) Fix bridge build with INET disabled, from Arnd Bergmann.

 9) Fix netlink array overrun for PROBE attributes in openvswitch, from
    Thomas Graf.

10) Don't hold spinlock across synchronize_irq() in tg3 driver, from
    Prashant Sreedharan.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  tg3: Release tp->lock before invoking synchronize_irq()
  tg3: tg3_reset_task() needs to use rtnl_lock to synchronize
  tg3: tg3_timer() should grab tp->lock before checking for tp->irq_sync
  team: avoid possible underflow of count_pending value for notify_peers and mcast_rejoin
  openvswitch: packet messages need their own probe attribtue
  i40e: adds FCoE configure option
  cxgb4vf: Fix queue allocation for 40G adapter
  netdevice: Add missing parentheses in macro
  bridge: only provide proxy ARP when CONFIG_INET is enabled
  neighbour: fix base_reachable_time(_ms) not effective immediatly when changed
  net: fec: fix MDIO bus assignement for dual fec SoC's
  xen-netfront: use different locks for Rx and Tx stats
  drivers: net: cpsw: fix multicast flush in dual emac mode
  cxgb4vf: Initialize mdio_addr before using it
  net: Corrected the comment describing the ndo operations to reflect the actual prototype for couple of operations
  usb/kaweth: use GFP_ATOMIC under spin_lock in usb_start_wait_urb()
  MAINTAINERS: add me as ibmveth maintainer
  tipc: fix bug in broadcast retransmit code
  update ip-sysctl.txt documentation (v2)
  net/at91_ether: prepare and unprepare clock
  ...

Prashant Sreedharan says:

====================
tg3: synchronize_irq() should be called without taking locks

v2: Added Reported-by, Tested-by fields and reference to the thread that
    reported the problem

This series addresses the problem reported by Peter Hurley in mail thread
https://lkml.org/lkml/2015/1/12/1082
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

synchronize_irq() can sleep waiting, for pending IRQ handlers so driver
should release the tp->lock spin lock before invoking synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently tg3_reset_task() uses only tp->lock for synchronizing with code
paths like tg3_open() etc. But since tp->lock is released before doing
synchronize_irq(), rtnl_lock should be taken in tg3_reset_task() to
synchronize it with other code paths.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to avoid the race between tg3_timer() and the execution paths
which does not invoke tg3_timer_stop() and releases tp->lock before
calling synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull kvm fixes from Paolo Bonzini:
 "Two bugfixes for arm64.  I will have another pull request next week,
  but otherwise things are calm"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  arm64: KVM: Fix HCR setting for 32bit guests
  arm64: KVM: Fix TLB invalidation by IPA/VMID

This patch is fixing a race condition that may cause setting
count_pending to -1, which results in unwanted big bulk of arp messages
(in case of "notify peers").

Consider following scenario:

count_pending == 2
   CPU0                                           CPU1
					team_notify_peers_work
					  atomic_dec_and_test (dec count_pending to 1)
					  schedule_delayed_work
 team_notify_peers
   atomic_add (adding 1 to count_pending)
					team_notify_peers_work
					  atomic_dec_and_test (dec count_pending to 1)
					  schedule_delayed_work
					team_notify_peers_work
					  atomic_dec_and_test (dec count_pending to 0)
   schedule_delayed_work
					team_notify_peers_work
					  atomic_dec_and_test (dec count_pending to -1)

Fix this race by using atomic_dec_if_positive - that will prevent
count_pending running under 0.

Fixes: fc423ff0 ("team: add peer notification")
Fixes: 492b200e  ("team: add support for sending multicast rejoins")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull s390 fixes from Martin Schwidefsky:
 "Two small performance tweaks, the plumbing for the execveat system
  call and a couple of bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/uprobes: fix user space PER events
  s390/bpf: Fix JMP_JGE_X (A > X) and JMP_JGT_X (A >= X)
  s390/bpf: Fix ALU_NEG (A = -A)
  s390/mm: avoid using pmd_to_page for !USE_SPLIT_PMD_PTLOCKS
  s390/timex: fix get_tod_clock_ext() inline assembly
  s390: wire up execveat syscall
  s390/kernel: use stnsm 255 instead of stosm 0
  s390/vtime: Get rid of redundant WARN_ON
  s390/zcrypt: kernel oops at insmod of the z90crypt device driver

User space is currently sending a OVS_FLOW_ATTR_PROBE for both flow
and packet messages. This leads to an out-of-bounds access in
ovs_packet_cmd_execute() because OVS_FLOW_ATTR_PROBE >
OVS_PACKET_ATTR_MAX.

Introduce a new OVS_PACKET_ATTR_PROBE with the same numeric value
as OVS_FLOW_ATTR_PROBE to grow the range of accepted packet attributes
while maintaining to be binary compatible with existing OVS binaries.

Fixes: 05da5898 ("openvswitch: Add support for OVS_FLOW_ATTR_PROBE.")
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tracked-down-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds FCoE config option I40E_FCOE, so that FCoE can be enabled
as needed but otherwise have it disabled by default.

This also eliminate multiple FCoE config checks, instead now just
one config check for CONFIG_I40E_FCOE.

The I40E FCoE was added with 3.17 kernel and therefore this patch
shall be applied to stable 3.17 kernel also.

CC: <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull file locking fix from Jeff Layton:
 "Just a simple bugfix for a regression that I introduced into v3.18
  with the internal lease API overhaul -- mea culpa.  Kudos to Linda and
  Neil for tracking this down and fixing it"

* tag 'locks-v3.19-1' of git://git.samba.org/jlayton/linux:
  locks: fix NULL-deref in generic_delete_lease

There are too many brackets. Maybe only one bracket is enough.
Signed-off-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For example, one could conceivably call
	for_each_netdev_in_bond_rcu(condition ? bond1 : bond2, slave)
and get an unexpected result.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce ovs_tunnel_route_lookup to consolidate route lookup
shared by vxlan, gre, and geneve ports.
Signed-off-by: Fan Du <fan.du@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull block layer fixes from Jens Axboe:
 "The major part is an update to the NVMe driver, fixing various issues
  around surprise removal and hung controllers.  Most of that is from
  Keith, and parts are simple blk-mq fixes or exports/additions of minor
  functions to aid this effort, and parts are changes directly to the
  NVMe driver.

  Apart from the above, this contains:

   - Small blk-mq change from me, killing an unused member of the
     hardware queue structure.

   - Small fix from Ming Lei, fixing up a few drivers that didn't
     properly check for ERR_PTR() returns from blk_mq_init_queue()"

* 'for-linus' of git://git.kernel.dk/linux-block:
  NVMe: Fix locking on abort handling
  NVMe: Start and stop h/w queues on reset
  NVMe: Command abort handling fixes
  NVMe: Admin queue removal handling
  NVMe: Reference count admin queue usage
  NVMe: Start all requests
  blk-mq: End unstarted requests on a dying queue
  blk-mq: Allow requests to never expire
  blk-mq: Add helper to abort requeued requests
  blk-mq: Let drivers cancel requeue_work
  blk-mq: Export if requests were started
  blk-mq: Wake tasks entering queue on dying
  blk-mq: get rid of ->cmd_size in the hardware queue
  block: fix checking return value of blk_mq_init_queue
  block: wake up waiters when a queue is marked dying
  NVMe: Fix double free irq
  blk-mq: Export freeze/unfreeze functions
  blk-mq: Exit queue on alloc failure

Tom Herbert says:

====================
net: Remote checksum offload for VXLAN

This patch set adds support for remote checksum offload in VXLAN.

The remote checksum offload is generalized by creating a common
function (remcsum_adjust) that does the work of modifying the
checksum in remote checksum offload. This function can be called
from normal or GRO path. GUE was modified to use this function.

To support RCO is VXLAN we use the 9th bit in the reserved
flags to indicated remote checksum offload. The start and offset
values are encoded n a compressed form in the low order (reserved)
byte of the vni field.

Remote checksum offload is described in
https://tools.ietf.org/html/draft-herbert-remotecsumoffload-01

Changes in v2:
  - Add udp_offload_callbacks which has GRO functions that take a
    udp_offload pointer argument. This argument can be used to retrieve
    a per port structure of the encapsulation for use in gro processing
    (mostly by doing container_of on the structure).
  - Use the 10th bit in VXLAN flags for RCO which does not seem to
    conflict with other proposals at this time (ie. VXLAN-GPE and
    VXLAN-GPB)
  - Require that RCO must be explicitly enabled on the receiver
    as well as the sender.

Tested by running 200 TCP_STREAM connections with VXLAN (over IPv4).

With UDP checksums and Remote Checksum Offload
  IPv4
      Client
        11.84% CPU utilization
      Server
        12.96% CPU utilization
      9197 Mbps
  IPv6
      Client
        12.46% CPU utilization
      Server
        14.48% CPU utilization
      8963 Mbps

With UDP checksums, no remote checksum offload
  IPv4
      Client
        15.67% CPU utilization
      Server
        14.83% CPU utilization
      9094 Mbps
  IPv6
      Client
        16.21% CPU utilization
      Server
        14.32% CPU utilization
      9058 Mbps

No UDP checksums
  IPv4
      Client
        15.03% CPU utilization
      Server
        23.09% CPU utilization
      9089 Mbps
  IPv6
      Client
        16.18% CPU utilization
      Server
        26.57% CPU utilization
       8954 Mbps
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for remote checksum offload in VXLAN. This uses a
reserved bit to indicate that RCO is being done, and uses the low order
reserved eight bits of the VNI to hold the start and offset values in a
compressed manner.

Start is encoded in the low order seven bits of VNI. This is start >> 1
so that the checksum start offset is 0-254 using even values only.
Checksum offset (transport checksum field) is indicated in the high
order bit in the low order byte of the VNI. If the bit is set, the
checksum field is for UDP (so offset = start + 6), else checksum
field is for TCP (so offset = start + 16). Only TCP and UDP are
supported in this implementation.

Remote checksum offload for VXLAN is described in:

https://tools.ietf.org/html/draft-herbert-vxlan-rco-00

Tested by running 200 TCP_STREAM connections with VXLAN (over IPv4).

With UDP checksums and Remote Checksum Offload
  IPv4
      Client
        11.84% CPU utilization
      Server
        12.96% CPU utilization
      9197 Mbps
  IPv6
      Client
        12.46% CPU utilization
      Server
        14.48% CPU utilization
      8963 Mbps

With UDP checksums, no remote checksum offload
  IPv4
      Client
        15.67% CPU utilization
      Server
        14.83% CPU utilization
      9094 Mbps
  IPv6
      Client
        16.21% CPU utilization
      Server
        14.32% CPU utilization
      9058 Mbps

No UDP checksums
  IPv4
      Client
        15.03% CPU utilization
      Server
        23.09% CPU utilization
      9089 Mbps
  IPv6
      Client
        16.18% CPU utilization
      Server
        26.57% CPU utilization
       8954 Mbps
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces udp_offload_callbacks which has the same
GRO functions (but not a GSO function) as offload_callbacks,
except there is an argument to a udp_offload struct passed to
gro_receive and gro_complete functions. This additional argument
can be used to retrieve the per port structure of the encapsulation
for use in gro processing (mostly by doing container_of on the
structure).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When IPV4 support is disabled, we cannot call arp_send from
the bridge code, which would result in a kernel link error:

net/built-in.o: In function `br_handle_frame_finish':
:(.text+0x59914): undefined reference to `arp_send'
:(.text+0x59a50): undefined reference to `arp_tbl'

This makes the newly added proxy ARP support in the bridge
code depend on the CONFIG_INET symbol and lets the compiler
optimize the code out to avoid the link error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 95850116 ("bridge: Add support for IEEE 802.11 Proxy ARP")
Cc: Kyeyoon Park <kyeyoonp@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace tasklet with NAPI.

Add rx_queue to queue the remaining rx packets if the number of the
rx packets is more than the request from poll().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ding Tianhong says:

====================
add hisilicon hip04 ethernet driver

v13:
- Fix the problem of alignment parameters for function and checkpatch warming.

v12:
- According Alex's suggestion, modify the changelog and add MODULE_DEVICE_TABLE
  for hip04 ethernet.

v11:
- Add ethtool support for tx coalecse getting and setting, the xmit_more
  is not supported for this patch, but I think it could work for hip04,
  will support it later after some tests for performance better.

  Here are some performance test results by ping and iperf(add tx_coalesce_frames/users),
  it looks that the performance and latency is more better by tx_coalesce_frames/usecs.

  - Before:
    $ ping 192.168.1.1 ...
    === 192.168.1.1 ping statistics ===
    24 packets transmitted, 24 received, 0% packet loss, time 22999ms
    rtt min/avg/max/mdev = 0.180/0.202/0.403/0.043 ms

    $ iperf -c 192.168.1.1 ...
    [ ID] Interval       Transfer     Bandwidth
    [  3]  0.0- 1.0 sec   115 MBytes   945 Mbits/sec

  - After:
    $ ping 192.168.1.1 ...
    === 192.168.1.1 ping statistics ===
    24 packets transmitted, 24 received, 0% packet loss, time 22999ms
    rtt min/avg/max/mdev = 0.178/0.190/0.380/0.041 ms

    $ iperf -c 192.168.1.1 ...
    [ ID] Interval       Transfer     Bandwidth
    [  3]  0.0- 1.0 sec   115 MBytes   965 Mbits/sec

v10:
- According Arnd's suggestion, remove the skb_orphan and use the hrtimer
  for the cleanup of the TX queue and add some modification for the hip04
  drivers.
  1) drop the broken skb_orphan call
  2) drop the workqueue
  3) batch cleanup based on tx_coalesce_frames/usecs for better throughput
  4) use a reasonable default tx timeout (200us, could be shorted
     based on measurements) with a range timer
  5) fix napi poll function return value
  6) use a lockless queue for cleanup

v9:
- There is no tx completion interrupts to free DMAd Tx packets, it means taht
  we rely on new tx packets arriving to run the destructors of completed packets,
  which open up space in their sockets's send queues. Sometimes we don't get such
  new packets causing Tx to stall, a single UDP transmitter is a good example of
  this situation, so we need a clean up workqueue to reclaims completed packets,
  the workqueue will only free the last packets which is already stay for several jiffies.
  Also fix some format cleanups.

v8:
- Use poll to reclaim xmitted buffer as workaround since no tx done interrupt

v7:
- Remove select NET_CORE in 0002

v6:
- Suggest by Russell: Use netdev_sent_queue & netdev_completed_queue to solve latency issue
  Also shorten the period of timer, which is used to wakeup the queue since no
  tx completed interrupt.

v5:
- no big change, fix typo

v4:
- Modify accoringly to the suggetion from Arnd, Florian, Eric, David
  Use of_parse_phandle_with_fixed_args & syscon_node_to_regmap get ppe info
  Add skb_orphan() and tx_timer for reclaim since no tx_finished interrupt
  Update timeout, and move of_phy_connect to probe to reuse open/stop

v3:
- Suggest from Arnd, use syscon & regmap_write/read to replace static void __iomem *ppebase.
  Modify hisilicon-hip04-net.txt accrordingly to suggestion from Florian and Sergei.

v2:
- Got many suggestions from Russell, Arnd, Florian, Mark and Sergei
  Remove memcpy, use dma_map/unmap_single, use dma_alloc_coherent rather than dma_pool, etc.
  Refer property in ethernet.txt, change ppe description, etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Support Hisilicon hip04 ethernet driver, including 100M / 1000M controller.
The controller has no tx done interrupt, reclaim xmitted buffer in the poll.

v13: Fix the problem of alignment parameters for function and checkpatch warming.

v12: According Alex's suggestion, modify the changelog and add MODULE_DEVICE_TABLE
     for hip04 ethernet.

v11: Add ethtool support for tx coalecse getting and setting, the xmit_more
     is not supported for this patch, but I think it could work for hip04,
     will support it later after some tests for performance better.

     Here are some performance test results by ping and iperf(add tx_coalesce_frames/users),
     it looks that the performance and latency is more better by tx_coalesce_frames/usecs.

     - Before:
     $ ping 192.168.1.1 ...
     === 192.168.1.1 ping statistics ===
     24 packets transmitted, 24 received, 0% packet loss, time 22999ms
     rtt min/avg/max/mdev = 0.180/0.202/0.403/0.043 ms

     $ iperf -c 192.168.1.1 ...
     [ ID] Interval       Transfer     Bandwidth
     [  3]  0.0- 1.0 sec   115 MBytes   945 Mbits/sec

     - After:
     $ ping 192.168.1.1 ...
     === 192.168.1.1 ping statistics ===
     24 packets transmitted, 24 received, 0% packet loss, time 22999ms
     rtt min/avg/max/mdev = 0.178/0.190/0.380/0.041 ms

     $ iperf -c 192.168.1.1 ...
     [ ID] Interval       Transfer     Bandwidth
     [  3]  0.0- 1.0 sec   115 MBytes   965 Mbits/sec

v10: According David Miller and Arnd Bergmann's suggestion, add some modification
     for v9 version
     - drop the workqueue
     - batch cleanup based on tx_coalesce_frames/usecs for better throughput
     - use a reasonable default tx timeout (200us, could be shorted
       based on measurements) with a range timer
     - fix napi poll function return value
     - use a lockless queue for cleanup
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hisilicon hip04 platform mdio driver
Reuse Marvell phy drivers/net/phy/marvell.c
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the Device Tree bindings for the Hisilicon hip04
Ethernet controller, including 100M / 1000M controller.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When setting base_reachable_time or base_reachable_time_ms on a
specific interface through sysctl or netlink, the reachable_time
value is not updated.

This means that neighbour entries will continue to be updated using the
old value until it is recomputed in neigh_period_work (which
    recomputes the value every 300*HZ).
On systems with HZ equal to 1000 for instance, it means 5mins before
the change is effective.

This patch changes this behavior by recomputing reachable_time after
each set on base_reachable_time or base_reachable_time_ms.
The new value will become effective the next time the neighbour's timer
is triggered.

Changes are made in two places: the netlink code for set and the sysctl
handling code. For sysctl, I use a proc_handler. The ipv6 network
code does provide its own handler but it already refreshes
reachable_time correctly so it's not an issue.
Any other user of neighbour which provide its own handlers must
refresh reachable_time.
Signed-off-by: Jean-Francois Remy <jeff@melix.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

On i.MX28, the MDIO bus is shared between the two FEC instances.
The driver makes sure that the second FEC uses the MDIO bus of the
first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC
has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC
is not an option since other logic, triggered by this quirk, is
still needed.

Furthermore, there are board designs which use the same MDIO bus
for both PHY's even though the second bus would be available on the
SoC side. Such layout are popular since it saves pins on SoC side.
Due to the above quirk, those boards currently do work fine. The
boards in the mainline tree with such a layout are:
- Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
- Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)

This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which
makes sure that the MDIO bus of the first FEC is used in any case.

However, the boards above do have a SoC with a MDIO bus for each FEC
instance. But the PHY's are not connected in a 1:1 configuration. A
proper device tree description is needed to allow the driver to
figure out where to find its PHY. This patch fixes that shortcoming
by adding a MDIO bus child node to the first FEC instance, along
with the two PHY's on that bus, and making use of the phy-handle
property to add a reference to the PHY's.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently `ethtool -S` simply returns "no stats available". It
would be more useful to see what the various ethtool statistics
registers' values are. This change implements get_ethtool_stats,
get_strings, and get_sset_count functions to accomplish this.

Read all GEM statistics registers and sum them into
macb.ethtool_stats. Add the necessary infrastructure to make this
accessible via `ethtool -S`.

Update gem_update_stats to utilize ethtool_stats.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change is to help improve at-a-glace knowledge of the purpose of the
various Cadence MACB/GEM registers. Comments are more helpful for human
readability than short acronyms.

Describe various #define varibles Cadence MACB/GEM registers as documented
in Xilinix's "Zynq-7000 All Programmable SoC TechnicalReference Manual, v1.9.1
(UG-585)"
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Vrabel says:

====================
xen-netfront: refactor making Tx requests

As netfront as evolved to handle different sorts of skbs the code to
fill a Tx requests has been copy and pasted several times.  The series
refactors this and a few other areas.

The first patch is to a Xen header but this can be merged via
net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Eliminate all the duplicate code for making Tx requests by
consolidating them into a single xennet_make_one_txreq() function.

xennet_make_one_txreq() and xennet_make_txreqs() work with pages and
offsets so it will be easier to make netfront handle highmem frags in
the future.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A function to count the number of slots an skb needs is more useful
than one that counts the slots needed for only the frags.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pfn_to_mfn(page_to_pfn(p)) is a common use case so add a generic
helper for it.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each per bucket lock covers a configurable number of buckets. While
shrinking, two buckets in the old table contain entries for a single
bucket in the new table. We need to lock down both while linking.
Check if they are protected by different locks to avoid a recursive
lock.

Fixes: 97defe1e ("rhashtable: Per bucket locks & deferred expansion/shrinking")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'leds-fixes-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds

Pull LED fix from Bryan Wu.

* 'leds-fixes-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
  leds: netxbig: fix oops at probe time

Pull WRITE_ONCE argument order change from Christian Borntraeger:
 "As discussed on LKML[1] it was agreed that WRITE_ONCE(x, val) is
  better than ASSIGN_ONCE(val, x)

  Lets change that for 3.19 as 3.19 has no user yet, but the first users
  will hit linux-next soon"

[1] http://marc.info/?l=linux-kernel&m=142081181707596

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
  kernel: Change ASSIGN_ONCE(val, x) to WRITE_ONCE(x, val)

The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>