- 03 Sep, 2013 40 commits
-
-
Chad Dupuis authored
Unless there is a need to observe them, the queue depth ramp up/down messages are a nuisance and may cause the system to become unresponsive so move it a non-default logging level. Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Joe Carnuccio authored
Signed-off-by:
Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by:
-
Santosh Vernekar authored
Earlier IDC-TIME-EXTEND aen was a nop and ignored by driver. We now have to handle the aen so that other protocol drivers can use time extension during some loopback operations. Signed-off-by:
Santosh Vernekar <santosh.vernekar@qlogic.com> Signed-off-by:
-
Armen Baloyan authored
[SCSI] qla2xxx: Set default critical temperature value in cases when ISPFX00 firmware doesn't provide it Signed-off-by:
Armen Baloyan <armen.baloyan@qlogic.com> Signed-off-by:
-
Armen Baloyan authored
[SCSI] qla2xxx: QLAFX00 make over temperature AEN handling informational, add log for normal temperature AEN Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Joe Carnuccio authored
Add the missing FCP statistics to sysfs. Add reset FCP statistics functionality via sysfs. Signed-off-by:
-
Chad Dupuis authored
[SCSI] qla2xxx: Make log message that prints when a completion status requires a port down more readable. Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
Srinivasa Rao <srinivasa.rao@qlogic.com> Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Joe Carnuccio authored
For supported ISPS, Read asic temperature by calling the GET PARAMS (type C) mailbox command. Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Armen Baloyan authored
Signed-off-by:
-
Andrew Vasquez authored
Signed-off-by:
Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by:
-
Joe Carnuccio authored
list_for_each_entry() never leaves the iterator pointing to null. Signed-off-by:
-
Atul Deshmukh authored
[jejb: checkpatch fixes] Signed-off-by:
Atul Deshmukh <atul.deshmukh@qlogic.com> Signed-off-by:
-
Oleksandr Khoshaba authored
The patch changes a specifier used to output some variables. Instead of using stack for each byte the '%*ph[CN]' allows to take a one pointer and prints entire buffer as a hexadecimal string with the separator ':' or ''. Signed-off-by:
Oleksandr Khoshaba <Oleksandr.Khoshaba@gmail.com> Signed-off-by:
-
Jan Vesely authored
Signed-off-by:
Jan Vesely <jvesely@redhat.com> Acked-by:
Sreekanth Reddy <Sreekanth.Reddy@lsi.com> Signed-off-by:
-
Jan Vesely authored
Signed-off-by:
-
Rasesh Mody authored
This patch updates the firmware to address the thermal notification issue Signed-off-by:
Rasesh Mody <rmody@brocade.com> Signed-off-by:
-
Bradley Grove authored
This is a new driver for ATTO Technology's ExpressSAS series of hardware RAID adapters. It supports the following adapters: - ExpressSAS R60F - ExpressSAS R680 - ExpressSAS R608 - ExpressSAS R644 Signed-off-by:Bradley Grove <bgrove@attotech.com> Signed-off-by:
-
Dan Carpenter authored
Smatch complains that the reg_IRQ[] array only has MAXIRQ (16) elements so we are one space beyond the end of the array here. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by:
-
Vikas Chaudhary authored
Return error from function qla4_8xxx_collect_md_data() if minidump data collection fails. Signed-off-by:
-
Santosh Vernekar authored
Signed-off-by:
-
Santosh Vernekar authored
Add pex-dma support for ISP8324 and ISP8042 to improve the minidump capture time. Signed-off-by:
-
Steffen Maier authored
Enabling the data router support by default can increase performance in certain situations. It is safe to do so and tolerated in LPAR and under z/VM in case there is no data router support in that environment. Signed-off-by:
Steffen Maier <maier@linux.vnet.ibm.com> Reviewed-by:
Martin Peschke <mpeschke@linux.vnet.ibm.com> Signed-off-by:
-
Martin Peschke authored
Get rid of unused function zfcp_fsf_get_req and corresponding prototype definition. Commit a54ca0f6 in v2.6.28 "[SCSI] zfcp: Redesign of the debug tracing for HBA records." accidentally introduced this code which was dead in the first place. Signed-off-by:
-
Martin Peschke authored
strict_strtoul and friends are obsolete. Use kstrtoul functions instead. Signed-off-by:
-
Martin Peschke authored
minor cleanup for status read request Signed-off-by:
-
Sreekanth Reddy authored
Added a driver module parameter max_msix_vectors. Using this module parameter the maximum number of MSI-X vectors could be set. The number of MSI-X vectors used would be the minimum of MSI-X vectors supported by the HBA, the number of CPU cores and the value set to max_msix_vectors module parameter. The default value of this module parameter is set to 8. The default value of this parameter is set to 8 inorder to reduce the amount of memory required for Reply Descriptor Post queue. This is because with the higher MSI-X vectors, some times kernel is not able to allocate the requested amount of memory and crash is observed. To overcome this problem, the default value is set to 8. Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
