The slave address of device to be configured in packet
header as follows:
    7 bit address: PacketHeader3[7:1]
    10 bit address: PacketHeader3[9:0]

Fixing the code to make packet header3 properly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Apply a naming pattern like in the rest of the subsystem to a first set
of mux drivers. Those drivers are the low-hanging fruit; we want to pick
them to motivate upcoming drivers to follow the new pattern. The missing
GPIO driver will be converted in a later patch.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com> (pca9541)
Acked-by: Jean Delvare <khali@linux-fr.org>

This finds the struct i2c_adapter * for a given device tree node. Just
like of_find_i2c_device_by_node.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

This converts a struct device * to a struct i2c_adapter * while verifying
that the device really is an I2C adapter. Just like i2c_verify_client.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

This patch adds support for s3c2440 I2C bus controller dedicated HDMIPHY device on
Exynos4 platform. Some quirks are introduced due to differences between HDMIPHY
and other I2C controllers on Exynos4.  These differences are:
- no GPIOs, HDMIPHY is inside the SoC and the controller is connected
  internally
- due to unknown reason (probably HW bug in HDMIPHY and/or the controller) a
  transfer fails to finish. The controller hangs after sending the last byte,
  the workaround for this bug is resetting the controller after each transfer
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Tested-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Reorganize driver a bit to better handle device tree-based systems:

 - move machine type to driver's private structure instead of
   quering platform device variants in runtime

 - replace s3c24xx_i2c_type enum with unsigned int that holds
   bitmask with revision-specific quirks
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

We got multiple patches to add mux support to device tree, so people are
using it happily already and build up on it. I also used it in a project
without encountering problems. 20 months of EXPERIMENTAL should do for
this.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Michael Lawnick <ml.lawnick@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: David Daney <ddaney.cavm@gmail.com>

For 'normal' i2c bus drivers, we can call of_i2c_register_devices()
and have the device tree framework automatically populate the bus with
the devices specified in the device tree.

This patch adds a common code to the i2c mux framework to have the mux
sub-busses be populated by the of_i2c_register_devices() too.  If the
mux device has an of_node, we populate the sub-bus' of_node so that
the subsequent call to of_i2c_register_devices() will find the
corresponding devices.

It seemed better to put this logic in i2c_add_mux_adapter() rather
than the individual mux drivers, as they will all probably want to do
the same thing.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>

[wsa: removed superfluous ret-variable and fixed a typo in a comment]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

And adjust all callers.

The new device parameter is used in the next patch to initialize the
mux's of_node so that its children may be automatically populated.
Signed-off-by: David Daney <david.daney@cavium.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

i2c_bus_type may contain both I2C clients and I2C adapters. Fix
of_find_i2c_device_by_node to call i2c_verify_client to ensure that it
only returns non-NULL of I2C clients.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for designware i2c.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

This patch adds in support for standby/S2R/hybernate for i2c-designware driver.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

The platform is removed, so there are no users of this driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

This patch adds device tree support to the pnx-i2c driver by using platform
resources for memory region and irq and removing dependency on mach includes.

The following platforms are affected:

* PNX
* LPC31xx (WIP)
* LPC32xx

The patch is based on a patch by Jon Smirl, working on lpc31xx integration
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>

Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Cc: Tomoya MORINAGA <tomoya.rohm@gmail.com>

cppcheck rightfully says:
drivers/i2c/busses/i2c-eg20t.c:266: style: The function 'ktime_lt' is never used
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Cc: Tomoya MORINAGA <tomoya.rohm@gmail.com>

smatch says:
drivers/i2c/busses/i2c-eg20t.c:702 pch_i2c_xfer() info: why not propagate 'ret' from mutex_lock_interruptible() instead of -512?

which is especially true since for -ENORESTARTSYS it is said in
linux/errno.h "signal_pending() MUST be set" which is not done here. So
just pass on the return value we got.
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Cc: Tomoya MORINAGA <tomoya.rohm@gmail.com>

sparse rightfully says:
drivers/i2c/busses/i2c-eg20t.c:990:59: warning: Using plain integer as NULL pointer
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Cc: Tomoya MORINAGA <tomoya.rohm@gmail.com>

By previous patch, pch_i2c_wait_for_xfer_complete can be merged
to pch_i2c_wait_for_check_xfer.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Currently, there are the same code for xfer complete check processing.
So, I add helper function pch_i2c_wait_for_check_xfer.
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

When entering deep sleep, the value in the registers I2CFDR and
I2CDFSRR are lost. This causes I2C access to fail after resuming.

Add suspend/resume routines to save/restore the registers
I2CFDR and I2CDFSRR.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

This patch enables DT support for the IIC driver
used on SH-based SoCs such as sh7722 and sh7724
among others as well as SH-Mobile SoCs such as
sh7367, sh7377, sh7372, sh73a0 and r8a7740.

Tested with out-of-tree DT support code on the
sh7372 Mackerel board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

The platforms using i2c-pnx.c both defined a duplicated i2c.h (used nowhere
else). This patch removes those and integrates the contents into the driver
itself.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

As a precondition for device tree conversion, the platforms using i2c-pnx.c are
converted to using mem and irq resources instead of platform data.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

The STM SPEAr platform can only access the i2c controller register
via 16bit read/write functions. This patch adds support to
automatically detect this 16bit access mode.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Commit 488bf314 ("i2c: Allow i2c_add_numbered_adapter() to assign a
bus id") reworked i2c_add_numbered_adapter() to call i2c_add_adapter()
if requested bus was -1.

This allows to simplify driver's initialization procedure by using
just one function for static and dynamic adapter id registration.

This patch updates few more drivers (missed out in original patch)
to use this functionality.
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Commit 488bf314 ("i2c: Allow i2c_add_numbered_adapter() to assign a
bus id") reworked i2c-pxa driver leaving obsolete comment.

This commit simply drops it.
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Use standard of_match_ptr() to avoid defining variable unused
in non device tree builds.
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Pull x86 fixes form Peter Anvin

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  intel_mid_powerbtn: mark irq as IRQF_NO_SUSPEND
  arch/x86/platform/geode/net5501.c: change active_low to 0 for LED driver
  x86, relocs: Remove an unused variable
  asm-generic: Use __BITS_PER_LONG in statfs.h
  x86/amd: Re-enable CPU topology extensions in case BIOS has disabled it

Pull btrfs fixes from Chris Mason:
 "The big ones here are a memory leak we introduced in rc1, and a
  scheduling while atomic if the transid on disk doesn't match the
  transid we expected.  This happens for corrupt blocks, or out of date
  disks.

  It also fixes up the ioctl definition for our ioctl to resolve logical
  inode numbers.  The __u32 was a merging error and doesn't match what
  we ship in the progs."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: avoid sleeping in verify_parent_transid while atomic
  Btrfs: fix crash in scrub repair code when device is missing
  btrfs: Fix mismatching struct members in ioctl.h
  Btrfs: fix page leak when allocing extent buffers
  Btrfs: Add properly locking around add_root_to_dirty_list

Setting TIF_IA32 in load_aout_binary() used to be enough; these days
TASK_SIZE is controlled by TIF_ADDR32 and that one doesn't get set
there.  Switch to use of set_personality_ia32()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

verify_parent_transid needs to lock the extent range to make
sure no IO is underway, and so it can safely clear the
uptodate bits if our checks fail.

But, a few callers are using it with spinlocks held.  Most
of the time, the generation numbers are going to match, and
we don't want to switch to a blocking lock just for the error
case.  This adds an atomic flag to verify_parent_transid,
and changes it to return EAGAIN if it needs to block to
properly verifiy things.
Signed-off-by: Chris Mason <chris.mason@oracle.com>

Pull alpha fixes from Matt Turner:
 "My alpha tree is back up (after taking quite some time to get my GPG
  key signed).  It contains just some simple fixes."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
  alpha: silence 'const' warning in sys_marvel.c
  alpha: include module.h to fix modpost on Tsunami
  alpha: properly define get/set_rtc_time on Marvel/SMP
  alpha: VGA_HOSE depends on VGA_CONSOLE

The test in pdc_console_tty_close '!tty->count' was always wrong
because tty->count is decremented after tty->ops->close is called and
thus can never be zero. Hence the 'then' branch was never executed and
the timer never deleted.

This did not matter until commit 5dd5bc40 ("TTY: pdc_cons, use
tty_port").  There we needed to set TTY in tty_port to NULL, but this
never happened due to the bug above.

So change the test to really trigger at the last close by changing the
condition to 'tty->count == 1'.

Well, the driver should not touch tty->count at all.  It should use
tty_port->count and count open count there itself.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-and-tested-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull sound sound fixes from Takashi Iwai:
 "As good as nothing exciting here; just a few trivial fixes for various
  ASoC stuff."

* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: omap-pcm: Free dma buffers in case of error.
  ASoC: s3c2412-i2s: Fix dai registration
  ASoC: wm8350: Don't use locally allocated codec struct
  ASoC: tlv312aic23: unbreak resume
  ASoC: bf5xx-ssm2602: Set DAI format
  ASoC: core: check of_property_count_strings failure
  ASoC: dt: sgtl5000.txt: Add description for 'reg' field
  ASoC: wm_hubs: Make sure we don't disable differential line outputs

Pull an ACPI patch from Len Brown:
 "It fixes a D3 issue new in 3.4-rc1."

By Lin Ming via Len Brown:
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  ACPI: Fix D3hot v D3cold confusion

Currently, we'll try mounting any device who's major device number is
UNNAMED_MAJOR as NFS root.  This would happen for non-NFS devices as
well (such as 9p devices) but it wouldn't cause any issues since
mounting the device as NFS would fail quickly and the code proceeded to
doing the proper mount:

       [  101.522716] VFS: Unable to mount root fs via NFS, trying floppy.
       [  101.534499] VFS: Mounted root (9p filesystem) on device 0:18.

Commit 6829a048102a ("NFS: Retry mounting NFSROOT") introduced retries
when mounting NFS root, which means that now we don't immediately fail
and instead it takes an additional 90+ seconds until we stop retrying,
which has revealed the issue this patch fixes.

This meant that it would take an additional 90 seconds to boot when
we're not using a device type which gets detected in order before NFS.

This patch modifies the NFS type check to require device type to be
'Root_NFS' instead of requiring the device to have an UNNAMED_MAJOR
major.  This makes boot process cleaner since we now won't go through
the NFS mounting code at all when the device isn't an NFS root
("/dev/nfs").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>