The driver supports decoding and statically modelling PLL state (i.e.
we inherit state from bootloader) and provides support for all
peripherals that support simple one-bit gated clocks. The covers all
peripherals whose clocks come from the AHB, APB1 or APB2 buses.

It has been tested on an STM32F429I-Discovery board. The clock counts
for TIM2, USART1 and SYSTICK are all set correctly and the wall clock
looks OK when checked with a stopwatch. I have also tested a prototype
driver for the RNG hardware. The RNG clock is correctly enabled by the
framework (also did inverse test and proved that by changing DT to
configure the wrong clock bit then we observe the RNG driver to fail).
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
[sboyd@codeaurora.org: Silence sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

This adds documentation of device tree bindings for the clock related
portions of the STM32 RCC block.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Merge tag 'tegra-for-4.2-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next

clk: tegra: Changes for v4.2-rc1

This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.

Folded into this merge commit is a build error fix: s/clk/core in
clk_change_rate due to the new struct clk_core

Exynos4210 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpufreq support for these platforms can be removed.

Changes by Bartlomiej:
- dropped Exynos5250 support removal for now
- updated exynos-cpufreq.[c,h]

Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

The new CPU clock type allows the use of generic CPUfreq driver.
Switch Exynos4210 to using generic cpufreq driver.

Changes by Bartlomiej:
- removed non-Exynos4210 support for now

Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

With the addition of the new Samsung specific cpu-clock type, the
arm clock can be represented as a cpu-clock type. Add the CPU clock
configuration data and instantiate the CPU clock type for Exynos4210.

Changes by Bartlomiej:
- fixed issue with wrong dividers being setup by Common Clock Framework
  (by an addition of CLK_RECALC_NEW_RATES clock flag to mout_apll clock,
  without this change cpufreq-dt driver showed ~10 mA larger energy
  consumption when compared to cpufreq-exynos one when "performance"
  cpufreq governor was used on Exynos4210 SoC based Origen board), this
  was probably meant to be workarounded by use of CLK_GET_RATE_NOCACHE
  and CLK_DIVIDER_READ_ONLY clock flags in the original patchset (in
  "[PATCH v12 6/6] clk: samsung: remove unused clock aliases and update
  clock flags") but using these flags is not sufficient to fix the issue
  observed
- removed Exynos5250 and Exynos5420 support for now

Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

The CPU clock provider supplies the clock to the CPU clock domain. The
composition and organization of the CPU clock provider could vary among
Exynos SoCs. A CPU clock provider can be composed of clock mux, dividers
and gates. This patch defines a new clock type for CPU clock provider and
adds infrastructure to register the CPU clock providers for Samsung
platforms.

Changes by Bartlomiej:
- fixed issue with setting lower dividers before the parent clock speed
  was lowered (the issue resulted in lockup on Exynos4210 SoC based
  Origen board when "ondemand" cpufreq governor was stress tested)
- fixed missing spin_unlock on error in exynos_cpuclk_post_rate_change()
  problem by moving cfg_data search outside of the spin locked area
- removed leftover kfree() in exynos_register_cpu_clock() that could
  result in dereferencing the NULL pointer on error
- moved spin_lock earlier in exynos_cpuclk_pre_rate_change() to cover
  reading of E4210_SRC_CPU and E4210_DIV_CPU1 registers
- added missing "last chance" checks to wait_until_divider_stable() and
  wait_until_mux_stable() (needed in case that IRQ handling took long
  time to proceed and resulted in function printing incorrect error
  message about timeout)
- moved E4210_CPU_DIV[0,1]() macros just before their only users,
  this resulted in moving them from patch #2 to patch #3/6 ("clk:
  samsung: exynos4: add cpu clock configuration data and instantiate
  cpu clock")
- removed E5250_CPU_DIV[0,1](), E5420_EGL_DIV0() and E5420_KFC_DIV()
  macros for now
- added my Copyrights to drivers/clk/samsung/clk-cpu.c

Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

This flag is needed to fix the issue with wrong dividers being setup
by Common Clock Framework when using the new Exynos cpu clock support.

The issue happens because clk_core_set_rate_nolock()  calls
clk_calc_new_rates(clk, rate) before both pre/post clock notifiers have
a chance to run.  In case of Exynos cpu clock support pre/post clock
notifiers are registered for mout_apll clock which is a parent of armclk
cpu clock and dividers are modified in both pre and post clock notifier.
This results in wrong dividers values being later programmed by
clk_change_rate(top).  To workaround the problem CLK_RECALC_NEW_RATES
flag is added and it is set for mout_apll clock later so the correct
divider values are re-calculated after both pre and post clock notifiers
had run.

For example when using "performance" governor on Exynos4210 Origen board
the cpufreq-dt driver requests to change the frequency from 1000MHz to
1200MHz and after the change state of the relevant clocks is following:

Without use of CLK_GET_RATE_NOCACHE flag:

 fout_apll rate: 1200000000
         fout_apll_div_2 rate: 600000000
                 mout_clkout_cpu rate: 600000000
                         div_clkout_cpu rate: 600000000
                                 clkout_cpu rate: 600000000
         mout_apll rate: 1200000000
                 armclk rate: 1200000000
                 mout_hpm rate: 1200000000
                         div_copy rate: 300000000
                                 div_hpm rate: 300000000
                 mout_core rate: 1200000000
                         div_core rate: 1200000000
                                 div_core2 rate: 1200000000
                                         arm_clk_div_2 rate: 600000000
                                         div_corem0 rate: 300000000
                                         div_corem1 rate: 150000000
                                         div_periph rate: 300000000
                         div_atb rate: 300000000
                                 div_pclk_dbg rate: 150000000
                 sclk_apll rate: 1200000000
                         sclk_apll_div_2 rate: 600000000

With use of CLK_GET_RATE_NOCACHE flag:

 fout_apll rate: 1200000000
         fout_apll_div_2 rate: 600000000
                 mout_clkout_cpu rate: 600000000
                         div_clkout_cpu rate: 600000000
                                 clkout_cpu rate: 600000000
         mout_apll rate: 1200000000
                 armclk rate: 1200000000
                 mout_hpm rate: 1200000000
                         div_copy rate: 200000000
                                 div_hpm rate: 200000000
                 mout_core rate: 1200000000
                         div_core rate: 1200000000
                                 div_core2 rate: 1200000000
                                         arm_clk_div_2 rate: 600000000
                                         div_corem0 rate: 300000000
                                         div_corem1 rate: 150000000
                                         div_periph rate: 300000000
                         div_atb rate: 240000000
                                 div_pclk_dbg rate: 120000000
                 sclk_apll rate: 150000000
                         sclk_apll_div_2 rate: 75000000

Without this change cpufreq-dt driver showed ~10 mA larger energy
consumption when compared to cpufreq-exynos one when "performance"
cpufreq governor was used on Exynos4210 SoC based Origen board.

This issue was probably meant to be workarounded by use of
CLK_GET_RATE_NOCACHE and CLK_DIVIDER_READ_ONLY clock flags in
the original Exynos cpu clock patchset (in "[PATCH v12 6/6] clk:
samsung: remove unused clock aliases and update clock flags" patch)
but usage of these flags is not sufficient to fix the issue observed.

Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Add DT binding documentation for lpc1850-ccu clk driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Add driver for NXP LPC18xx/43xx Clock Control Unit (CCU). The CCU
provides fine grained gating of most clocks present in the SoC.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Add DT binding documentation for lpc1850-cgu driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Add driver for NXP LPC18xx/43xx Clock Generation Unit (CGU). The CGU
contains several clock generators and output stages that route the
clocks either directly to peripherals or to a Clock Control Unit
(CCU).
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Main PLL controller has post divider bits in a separate register in
pll controller. Use the value from this register instead of fixed
divider when available.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Merge tag 'sunxi-clocks-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next

Allwinner clocks additions for 4.2

One error fix, and one patch to add support for the USB clock found on the
Allwinner A23 and A33

The crypto SRAM, used by the armada 370 cpuidle code to workaround a bug
in the BootROM code, requires the crypto clk to be up and running.
Flag the crypto clk as IGNORE_UNUSED until we add the proper
infrastructure to define the crypto SRAM in the DT and reference the crypto
clk in this SRAM node.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Remove old Cygnus dummy clock binding document, as it's replaced by
Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

The Broadcom Cygnus SoC is architected under the iProc architecture. It
has the following PLLs: ARMPLL, GENPLL, LCPLL0, MIPIPLL, all dervied
from an onboard crystal. Cygnus also has various ASIU clocks that are
derived directly from the onboard crystal.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

The clock code under drivers/clk/bcm now contains code for both the
Broadcom mobile SoCs and the iProc SoCs. Change the the makefile
dependency to be under config flag CONFIG_ARCH_BCM that's enabled for
both families of SoCs
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

This adds basic and generic support for various iProc PLLs and clocks
including the ARMPLL, GENPLL, LCPLL, MIPIPLL, and ASIU clocks.

SoCs under the iProc architecture can define their specific register
offsets and clock parameters for their PLL and clock controllers. These
parameters can be passed as arugments into the generic iProc PLL and
clock setup functions

Derived from code originally provided by Jonathan Richardson
<jonathar@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Document the device tree binding for Broadcom iProc architecture based
clock controller
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Signed-off-by: Michael Turquette <mturquette@baylibre.com>

Merge branch 'clk-shmobile-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next

This error handling hopefully isn't needed but it make the static
checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

A recent change to mark parent names as const missed this struct
member so we get warnings like:

drivers/clk/pxa/clk-pxa25x.c:122:2: warning: initialization
discards 'const' qualifier from pointer target type

Fix it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

The debug_node field is only used when DEBUG_FS config is selected,
so declare it only if DEBUG_FS is selected.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

Currently it is not made explicit why clk_fixed_set_rate() can ignore
its arguments and unconditionally return success. Add a comment
to explain this.

We also mark the clk_ops table const since it should never be
modified at runtime.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

drivers/clk/clk-cdce925.c:550: warning: format ‘%u’ expects type
‘unsigned int’, but argument 6 has type ‘size_t’

Cc: Mike Looijmans <mike.looijmans@topic.nl>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

This line was indented too far.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

This patch adds 'CLK_IGNORE_UNUSED' flag to clocks which is required for
operation of secure monitor call (smc). System will hang when it executes 'smc'
with one of those clock is gated. All related clocks must be enabled.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>

This patch adds the CLK_SET_RATE_PARENT flag for 'aclk_g3d' clock and parent
clocks becuase 'aclk_g3d' is used to change GPU frequency for DVFS (Dynamic
Voltage Frequency Scaling) feature and adds CLK_IGNORE_UNUSED flags to
'aclk_asyncapbs_g3d'/'aclk_asyncapbm_g3d' clocks to access the SFR
of the MALI device.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
[cw00.choi: Add patch description and add CLK_SET_RATE_PARENT to 'aclk_g3d' clk]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>

This DIV_CPIF register must be stored when the system is suspended, and must
be restored on system resume. This patch adds the register to the list of
restored registers.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>

This patch adds CLK_SET_RATE_PARENT flag to support DVFS of Cortex-{A53|A57}
core (big.LITTLE core) because 'sclk_{apollo|atlas}' leaf clock is used to
change the CPU frequency of Cortex-{A53|A57} core in arm_big_little.c driver.
- 'apollo' word means the LITTLE core (Cortex-A53 core) in Exynos5433 TRM.
- 'atlas' word means the big core (Cortex-A57 core) in Exynos5433 TRM.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>

Pull MIPS updates from Ralf Baechle:
 "Eight fixes across arch/mips.  Nothing stands particuarly out nor is
  complicated but fixes keep coming in at a higher than comfortable
  rate"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: KVM: Do not sign extend on unsigned MMIO load
  MIPS: BPF: Fix stack pointer allocation
  MIPS: Loongson-3: Fix a cpu-hotplug issue in loongson3_ipi_interrupt()
  MIPS: Fix enabling of DEBUG_STACKOVERFLOW
  MIPS: c-r4k: Fix typo in probe_scache()
  MIPS: Avoid an FPE exception in FCSR mask probing
  MIPS: ath79: Add a missing new line in log message
  MIPS: ralink: Fix clearing the illegal access interrupt

Pull driver core fixes from Greg KH:
 "Here are two fixes for the driver core that resolve some reported
  issues.

  One is a regression from 4.0, the other a fixes a reported oops that
  has been there since 3.19.

  Both have been in linux-next for a while with no problems"

* tag 'driver-core-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  drivers/base: cacheinfo: handle absence of caches
  drivers: of/base: move of_init to driver_init

Pull staging / IIO fixes from Greg KH:
 "Here are some IIO driver fixes to resolve reported issues, some ozwpan
  fixes for some reported CVE problems, and a rtl8712 driver fix for a
  reported regression.

  All have been in linux-next successfully"

* tag 'staging-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: rtl8712: fix stack dump
  ozwpan: unchecked signed subtraction leads to DoS
  ozwpan: divide-by-zero leading to panic
  ozwpan: Use unsigned ints to prevent heap overflow
  ozwpan: Use proper check to prevent heap overflow
  iio: adc: twl6030-gpadc: Fix modalias
  iio: adis16400: Fix burst transfer for adis16448
  iio: adis16400: Fix burst mode
  iio: adis16400: Compute the scan mask from channel indices
  iio: adis16400: Use != channel indices for the two voltage channels
  iio: adis16400: Report pressure channel scale

Pull tty/serial driver fixes from Greg KH:
 "Here are a few TTY and Serial driver fixes for reported regressions
  and crashes.

  All of these have been in linux-next with no reported problems"

* tag 'tty-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  n_tty: Fix auditing support for cannonical mode
  serial: 8250_omap: provide complete custom startup & shutdown callbacks
  n_tty: Fix calculation of size in canon_copy_from_read_buf
  serial: imx: Fix DMA handling for IDLE condition aborts
  serial/amba-pl011: Unconditionally poll for FIFO space before each TX char

Pull USB and PHY driver fixes from Greg KH:
 "Here are some USB and PHY driver fixes that resolve some reported
  regressions.  Also in here are some new device ids.

  All of the details are in the shortlog and these patches have been in
  linux-next with no problems"

* tag 'usb-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
  USB: cp210x: add ID for HubZ dual ZigBee and Z-Wave dongle
  usb: renesas_usbhs: Don't disable the pipe if Control write status stage
  usb: renesas_usbhs: Fix fifo unclear in usbhsf_prepare_pop
  usb: gadget: f_fs: fix check in read operation
  usb: musb: fix order of conditions for assigning end point operations
  usb: gadget: f_uac1: check return code from config_ep_by_speed
  usb: gadget: ffs: fix: Always call ffs_closed() in ffs_data_clear()
  usb: gadget: g_ffs: Fix counting of missing_functions
  usb: s3c2410_udc: correct reversed pullup logic
  usb: dwc3: gadget: Fix incorrect DEPCMD and DGCMD status macros
  usb: phy: tahvo: Pass the IRQF_ONESHOT flag
  usb: phy: ab8500-usb: Pass the IRQF_ONESHOT flag
  usb: renesas_usbhs: Revise the binding document about the dma-names
  usb: host: xhci: add mutex for non-thread-safe data
  usb: make module xhci_hcd removable
  USB: serial: ftdi_sio: Add support for a Motion Tracker Development Board
  usb: gadget: f_midi: fix segfault when reading empty id
  phy: phy-rcar-gen2: Fix USBHS_UGSTS_LOCK value
  phy: omap-usb2: invoke pm_runtime_disable on error path
  phy: fix Kconfig dependencies
  ...