This driver had resided in the OMAP tree but is now to be in MTD.

Original authors were:
	Jarkko Lavinen <jarkko.lavinen@nokia.com> and Juha Yrjölä
	IRQ and DMA support written by Timo Teras
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

- add extended device information support
- add s25sl128 device support
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

code cleanup for m25p80.c
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch adds an erase_block command to enhance erase operation
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Removed duplicated include <asm/div64.h> in
drivers/mtd/nand/nandsim.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

They need to be exported, so let's give them less generic-sounding names
while we're at it.

Original export patch, along with the suggestion about the nomenclature,
from Stephen Rothwell.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This adds a WRITE_VERIFY Kconfig option to the DataFlash driver,
closely mirroring the similar NAND and ONENAND options, giving
an option to disable some code that's currently always enabled.

Removing this step probably saves a millisecond or so per page
when writing data, which will add up quickly since these pages
are small (the largest is 1 KiB).  It doesn't seem to add a
lot in terms of reliability, and wouldn't detect errors which
crop up when transferring data to the on-chip SRAM buffer.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

> > linux-next-20080805/drivers/mtd/devices/mtd_dataflash.c: In function 'add_dataflash_otp':
> > linux-next-20080805/drivers/mtd/devices/mtd_dataflash.c:670: error: too many arguments to function 'otp_setup'

Whoops, sorry ... I see what was going on.  My bad.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Timeouts are currently given by the typical operation time times 8.
It works in the general well-behaved case but not when an erase block is
failing. For erase operations, it seems that a failing erase block will
keep the device state machine in erasing state until the vendor
specified maximum timeout period has passed. By this time the driver
would have long since timed out, left erasing state and attempted
further operations which all fail. This patch implements timeouts using
values from the CFI Query structure when available.
The patch also sets a longer timeout for locking operations. The current
value used for locking/unlocking given by 1000000/HZ microseconds is too
short for devices like J3 and J5 Strataflash which have a typical clear
lock-bits time of 0.5 seconds.
Signed-off-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

There are some CFI chips which require non standard procedures to get 
into QRY mode. The possible way to support them would be trying 
different modes till QRY will be read. This patch introduce two new 
functions qry_mode_on qry_mode_off. qry_mode_on tries different commands 
in order switch chip into QRY mode.

So if we have one more "odd" chip - we just could add several lines to 
qry_mode_on. Also using these functions remove unnecessary code 
duplicaton in porbe procedure.

Currently there are two "odd" cases
1. Some old intel chips which require 0xFF before 0x98
2. ST M29DW chip which requires 0x98 to be sent at 0x555 (according to
CFI should be 0x55)

This patch is partialy based on the patch from Uwe
(see "[PATCH 2/4] [RFC][MTD] cfi_probe: remove Intel chip workaround"
thread )
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: Alexander Belyakov <abelyako@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This long overdue trivial change to the MTD_CFI_AMDSTD kconfig menu
description is intended to help clarify that this option also supports
Spansion flash devices.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This was a reference board for which support never got merged upstream.
Kill it off, at rmk's suggestion.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore
remove the dead code associated with !CONFIG_PPC_MERGE.

The mtd maps should be using the OF based mechanism.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Now that we can tell when we have one of the newer DataFlash chips,
optionally expose the 128 bytes of OTP memory they provide.  Tested
on at45db642 revision B and D chips.

Switch mtdchar over to a generic HAVE_MTD_OTP flag instead of adding
another #ifdef for each type of chip whose driver has OTP support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

* git://git.infradead.org/mtd-2.6:
  [MTD] [NAND] drivers/mtd/nand/nandsim.c: fix printk warnings
  [MTD] [NAND] Blackfin NFC Driver: Cleanup the error exit path of bf5xx_nand_probe function
  [MTD] [NAND] Blackfin NFC Driver: use standard dev_err() rather than printk()
  [MTD] [NAND] Blackfin NFC Driver: enable Blackfin nand HWECC support by default
  [MTD] [NAND] Blackfin NFC Driver: add proper devinit/devexit markings to probe/remove functions
  [MTD] [NAND] Blackfin NFC Driver: add support for the ECC layout the Blackfin bootrom uses
  [MTD] [NAND] Blackfin NFC Driver: fix bug - hw ecc calc by making sure we extract 11 bits from each register instead of 10
  [MTD] [NAND] Blackfin NFC Driver: fix bug - do not clobber the status from the first 256 bytes if operating on 512 pages
  [MTD] [NAND] diskonchip.c fix sparse endian warnings
  [MTD] [NAND] drivers/mtd/nand/nandsim.c needs div64.h
  [JFFS2] Fix allocation of summary buffer
  Fix rename of at91_nand -> atmel_nand
  [MTD] [NOR] drivers/mtd/chips/jedec_probe.c: fix Am29DL800BB device ID
  [MTD] MTD_DEBUG always does compile-time typechecks
  [MTD] DataFlash: bugfix, binary page sizes now handled
  [MTD] [NAND] fsl_elbc_nand.c: fix printk warning
  [MTD] [NAND] nandsim: support random page read command
  [MTD] [NAND] fix subpage read for small page NAND

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  [PATCH] pass struct path * to do_add_mount()
  [PATCH] switch mtd and dm-table to lookup_bdev()
  [patch 3/4] vfs: remove unused nameidata argument of may_create()
  [PATCH] devpts: switch to IDA
  [PATCH 2/2] proc: switch inode number allocation to IDA
  [PATCH 1/2] proc: fix inode number bogorithmetic
  [PATCH] fix bdev leak in block_dev.c do_open()
  [PATCH] fix races and leaks in vfs_quota_on() users
  [PATCH] clean dup2() up a bit
  [PATCH] merge locate_fd() and get_unused_fd()
  [PATCH] ipv4_static_sysctl_init() should be under CONFIG_SYSCTL
  Re: BUG at security/selinux/avc.c:883 (was: Re: linux-next: Tree

* 'audit.b54' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
  [PATCH] Fix the bug of using AUDIT_STATUS_RATE_LIMIT when set fail, no error output.
  [PATCH] Fix the kernel panic of audit_filter_task when key field is set
  Re: [PATCH] the loginuid field should be output in all AUDIT_CONFIG_CHANGE audit messages
  kernel/audit.c control character detection is off-by-one
  [PATCH] Audit: Collect signal info when SIGUSR2 is sent to auditd

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  au1xmmc: raise segment size limit.
  mmc_block: use proper sg iterators
  mmc: properly iterate over sg list in debug check
  mmc_test: Revert "mmc_test: test oversized sg lists"
  sdhci: check correct return value
  sdhci: disable DMA for req, not completely
  sdhci: handle bug in JMB38x for sizes < 4 bytes

* 'reg-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: TI bq24022 Li-Ion Charger driver
  regulator: maintainers - add maintainers for regulator framework.
  regulator: documentation - ABI
  regulator: documentation - machine
  regulator: documentation - regulator driver
  regulator: documentation - consumer interface
  regulator: documentation - overview
  regulator: core kbuild files
  regulator: regulator test harness
  regulator: add support for fixed regulators.
  regulator: regulator framework core
  regulator: fixed regulator interface
  regulator: machine driver interface
  regulator: regulator driver interface
  regulator: consumer device interface

Merge branch 'hotfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'hotfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  SELinux: /proc/mounts should show what it can

* git://git.infradead.org/battery-2.6:
  power_supply: Sharp SL-6000 (tosa) batteries support
  power_supply: fix up CHARGE_COUNTER output to be more precise
  power_supply: add CHARGE_COUNTER property and olpc_battery support for it
  power_supply: bump EC version check that we refuse to run with in olpc_battery
  power_supply: cleanup of the OLPC battery driver
  power_supply: add eeprom dump file to olpc_battery's sysfs
  power_supply: Support serial number in olpc_battery

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (28 commits)
  mm/hugetlb.c must #include <asm/io.h>
  video: Fix up hp6xx driver build regressions.
  sh: defconfig updates.
  sh: Kill off stray mach-rsk7203 reference.
  serial: sh-sci: Fix up SH7760/SH7780/SH7785 early printk regression.
  sh: Move out individual boards without mach groups.
  sh: Make sure AT_SYSINFO_EHDR is exposed to userspace in asm/auxvec.h.
  sh: Allow SH-3 and SH-5 to use common headers.
  sh: Provide common CPU headers, prune the SH-2 and SH-2A directories.
  sh/maple: clean maple bus code
  sh: More header path fixups for mach dir refactoring.
  sh: Move out the solution engine headers to arch/sh/include/mach-se/
  sh: I2C fix for AP325RXA and Migo-R
  sh: Shuffle the board directories in to mach groups.
  sh: dma-sh: Fix up dreamcast dma.h mach path.
  sh: Switch KBUILD_DEFCONFIG to shx3_defconfig.
  sh: Add ARCH_DEFCONFIG entries for sh and sh64.
  sh: Fix compile error of Solution Engine
  sh: Proper __put_user_asm() size mismatch fix.
  sh: Stub in a dummy ENTRY_OFFSET for uImage offset calculation.
  ...

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  generic, x86: fix add iommu_num_pages helper function
  x86: remove stray <6> in BogoMIPS printk
  x86: move dma32_reserve_bootmem() after reserve_crashkernel()

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] qeth: avoid use of include/asm-s390
  [S390] dont use kthread for smp_rescan_cpus().
  [S390] virtio console: fix section mismatch warning.
  [S390] cio: Include linux/string.h in schid.h.
  [S390] qdio: fix section mismatch bug.
  [S390] stp: fix section mismatch warning.
  [S390] Remove diag 0x260 call from memory detection.
  [S390] qdio: make sure qdr is aligned to page size
  [S390] Add support for memory hot-remove.
  [S390] Wire up new syscalls.
  [S390] cio: Memory allocation for idset changed.
  [S390] qeth: preallocated qeth header for hiper socket
  [S390] Optimize storage key operations for anon pages
  [S390] nohz/sclp: disable timer on synchronous waits.
  [S390] ipl: Reboot from alternate device does not work when booting from file
  [S390] dasd: Add support for enhanced VM UID
  [S390] Remove last P390 trace.

Raise the DMA block size limit from 2048 bytes to the maximum supported
by the DMA controllers on the chip (64KB on Au1100, 4MB on Au1200).

This gives a very small performance boost and apparently fixes an oops
when MMC-DMA and network traffic are active at the same time.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This reverts commit 48b5352e. Oversized
sg lists are not allowed anymore, and the core even checks for them in
debug mode, so this test is entirely incorrect.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Fix a copy-and-paste error.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The wrong flag was manipulated when an invalid sg list was given, turning
off DMA on the next (and all subsequent) request instead of the current
one.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

When the "status_get->mask" is "AUDIT_STATUS_RATE_LIMIT || AUDIT_STATUS_BACKLOG_LIMIT".
If "audit_set_rate_limit" fails and "audit_set_backlog_limit" succeeds, the "err" value
will be greater than or equal to 0. It will miss the failure of rate set.
Signed-off-by: Zhang Xiliang <zhangxiliang@cn.fujitsu.com>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

When calling audit_filter_task(), it calls audit_filter_rules() with audit_context is NULL.
If the key field is set, the result in audit_filter_rules() will be set to 1 and
ctx->filterkey will be set to key.
But the ctx is NULL in this condition, so kernel will panic.
Signed-off-by: Zhang Xiliang <zhangxiliang@cn.fujitsu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

> shouldn't these be using the "audit_get_loginuid(current)"  and if we
> are going to output loginuid we also should be outputting sessionid

Thanks for your detailed explanation.
I have made a new patch for outputing "loginuid" and "sessionid" by audit_get_loginuid(current) and audit_get_sessionid(current).
If there are some deficiencies, please give me your indication.
Signed-off-by: Zhang Xiliang <zhangxiliang@cn.fujitsu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Hello,

According to my understanding there is an off-by-one bug in the
function:

   audit_string_contains_control()

in:

  kernel/audit.c

Patch is included.

I do not know from how many places the function is called from, but for
example, SELinux Access Vector Cache tries to log untrusted filenames via
call path:

avc_audit()
     audit_log_untrustedstring()
         audit_log_n_untrustedstring()
             audit_string_contains_control()

If audit_string_contains_control() detects control characters, then the
string is hex-encoded. But the hex=0x7f dec=127, DEL-character, is not
detected.

I guess this could have at least some minor security implications, since a
user can create a filename with 0x7f in it, causing logged filename to
possibly look different when someone reads it on the terminal.
Signed-off-by: Vesa-Matti Kari <vmkari@cc.helsinki.fi>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Makes the kernel audit subsystem collect information about the sending
process when that process sends SIGUSR2 to the userspace audit daemon.
SIGUSR2 is a new interesting signal to auditd telling auditd that it
should try to start logging to disk again and the error condition which
caused it to stop logging to disk (usually out of space) has been
rectified.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>