Add rate limited print macros for warning and info level. This protects
the system from burst of prints depleting HW resources and spamming dmesg.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Add bar_addr field to store bar-0 address to avoid calling
pci_resource_start with hard-coded bar-0 as parameter.
Also note that different mlx5 device types will have bar_addr
on different bars.

This patch does not change any functionality.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Replace pci dev_err/warn/info messages with mlx5_core_err/warn/info
messages to provide a better report/debug of different mlx5 device types.

This patch does not change any functionality.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Use mlx5_core mdev private name in message instead of using pci dev_name
to provide a better report/debug of different mlx5 device types.

This patch does not change any functionality.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Detach mlx5_core mdev messages from pci device mdev->pdev messages and
provide a better report/debug of different mlx5 device types.

This patch does not change any functionality.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>

Using foundation from previous patches to factor mlx5_load_one flow
into three stages:
1. mlx5_function_setup() from previous patch to setup function
2. mlx5_init_once() from previous patch to init software objects
according to hw caps
3. New mlx5_load() to load mlx5 components

This provides a better logical separation of mlx5 core device
initialization flow and will help to seamlessly support creating different
mlx5 device types such as PF, VF and SF mlx5 sub-function virtual device.

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Function setup and teardown procedures are the basic procedure that
each mlx5 pci function should perform to boot up a mlx5 device function
and initialize basic communication with FW, before allocating any higher
level software/firmware resources.

This provides a better logical separation of mlx5 core device
initialization flow and will help to seamlessly support creating different
mlx5 device types such as PF, VF and SF mlx5 sub-function virtual device.

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Software structure initialization should be in mdev_init stage.

This provides a better logical separation of mlx5 core device
initialization flow and will help to seamlessly support creating different
mlx5 device types such as PF, VF and SF mlx5 sub-function virtual device.

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Separate resources initialization from pci initialization.

This provides a better logical separation of mlx5 core device
initialization flow and will help to seamlessly support creating different
mlx5 device types such as PF, VF and SF mlx5 sub-function virtual device.

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

As there is no user of mlx5_write64 that passes a spinlock to
mlx5_write64, remove this functionality and simplify the function.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

MLX5_*_DOORBELL_LOCK macros provided a way to avoid locking for
mlx5_write64 on 64-bit platforms where it's not necessary. Currently all
calls to mlx5_write64 don't use a spinlock, so the macros became unused.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Combine all HCA capabilities setters under one function
and compile out the ODP related function in case kernel
was compiled without ODP support.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>

Driver now supports new link modes: 50Gbps per lane support for
50G/100G/200G. This patch reads the correct field (legacy vs. extended)
based on a FW indication bit, and adds a translation function (link
modes to IB width and speed) to the new link modes.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This patch exposes new link modes (including 50Gbps per lane), and ext_*
fields which describes the new link modes in Port Type and Speed
register (PTYS).
Access functions, translation functions (speed <-> HW bits) and
link max speed function were modified.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Register Port Type and Speed (PTYS) introduces three new fields
extending the speed/protocols the can be reported and configured.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This patch fascicles queries to speed related fields in Port Type and
Speed register (PTYS) into a single API. I addition, this patch
refactors functions which serves only Ethernet driver: remove the
protocol type as an input parameter, move code from 'core' directory
into 'en' directory and add 'eth' prefix to the function's name. The
patch also encapsulates functions that are not used outside the Ethernet
driver removes redundant include files.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When dealing with the offloads mode initialization, driver refers to
the number of VFs and add magic number one (1) to take account of the
uplink. This is not clear and will make the code less readable after
adding other vports (e.g. host PF). As these are special vports
compared to VF vports, add a helper macro to denote such special
vports and eliminate the use of magic number.

Moreover, when creating offloads flow table and groups, the driver
reserves two more slots for UC and MC miss rules. Replace this magic
number with a helper macro as well.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

These are two macros in the driver general header which deal with the
number of total vports and if a vport is vport manager. Such macros
are vport entities, better to place them at the vport header file.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Driver used to name uplink vport as FDB_UPLINK_VPORT, it's hard to
comply with the same naming convention along with the introduction of
other vports. Use MLX5_VPORT as the prefix for such vports and
relocate the uplink vport definition to public header file for the
benefits of both net and IB drivers.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

ECPF doesn't support SR-IOV, but an ECPF E-Switch manager shall know
the max VFs supported by its peer host PF in order to control those
VF vports.

The current driver implementation uses the total vfs quantity as
provided by the pci sub-system for an upper bound of the VF vports
the e-switch code needs to deal with. This obviously can't work as
is on ECPF e-switch manager. For now, we use a hard coded value of
128 on such systems.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In Embedded CPU (EC) configurations, the EC driver needs to know when
the number of virtual functions change on the corresponding PF at the
host side. This is required so the EC driver can create or destroy
representor net devices that represent the VFs ports.

Whenever a change in the number of VFs occurs, firmware will generate an
event towards the EC which will trigger a work to complete the rest of
the handling. The specifics of the handling will be introduced in a
downstream patch.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The QUERY_HOST_PARAMS command is used by an Embedded CPU Physical
Function (ECPF) driver to identify and retrieve information about the
PF on the host side. E.g, number of virtual functions and PCI BDF.

The number of VFs can be changed on the fly, a function is added to
query current number of VFs and will be used in downstream patches.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

With the introduction of ECPF, we require that the ECPF driver will
aways call enable/disable HCA for that PF in the same way a PF does
this for its VFs. The PF is still responsible for calling enable and
disable HCA for its VFs.

To distinguish between the ECPF executing enable/disable HCA for
itself or for the PF, it sets the embedded CPU function bit in the
input params struct of these commands. When the bit is cleared and
function ID is zero, it refers to the peer PF.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Mellanox's SmartNIC combines embedded CPU(e.g, ARM) processing power
with advanced network offloads to accelerate a multitude of security,
networking and storage applications.

With the introduction of the SmartNIC, there is a new PCI function
called Embedded CPU Physical Function(ECPF). And it's possible for a
PF to get its ICM pages from the ECPF PCI function. Driver shall
identify if it is running on such a function by reading a bit in
the initialization segment.

When firmware asks for pages, it would issue a page request event
specifying how many pages it requests and for which function. That
driver responds with a manage_pages command providing the requested
pages along with an indication for which function it is providing these
pages.

The encoding before this patch was as follows:
    function_id == 0: pages are requested for the function receiving
                      the EQE.
    function_id != 0: pages are requested for VF identified by the
                      function_id value

A new one bit field in the EQE identifies that pages are requested for
the ECPF.

The notion of page_supplier can be introduced here and to support that,
manage pages and query pages were modified so firmware can distinguish
the following cases:

1. Function provides pages for itself
2. PF provides pages for its VF
3. ECPF provides pages to itself
4. ECPF provides pages for another function

This distinction is possible through the introduction of the bit
"embedded_cpu_function" in query_pages, manage_pages and page request
EQE.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

IB driver maintains different registration and load function calls
for uplink and VF vports. This is not necessary as they only differ
with each other on their profiles.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Use u16 for vport number, which matches how hardware refers to this
argument throughout commands.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Better to use void * and avoid unnecessary casts.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Update newly introduced function to be aligned to netdev coding style.

Fixes: 46861e3e ("net/mlx5: Set ODP SRQ support in firmware")
Reported-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>

mlx5_eq_cq_get() is called in IRQ handler, the spinlock inside
gets a lot of contentions when we test some heavy workload
with 60 RX queues and 80 CPU's, and it is clearly shown in the
flame graph.

In fact, radix_tree_lookup() is perfectly fine with RCU read lock,
we don't have to take a spinlock on this hot path. This is pretty
much similar to commit 291c566a
("net/mlx4_core: Fix racy CQ (Completion Queue) free"). Slow paths
are still serialized with the spinlock, and with synchronize_irq()
it should be safe to just move the fast path to RCU read lock.

This patch itself reduces the latency by about 50% for our memcached
workload on a 4.14 kernel we test. In upstream, as pointed out by Saeed,
this spinlock gets some rework in commit 02d92f79
("net/mlx5: CQ Database per EQ"), so the difference could be smaller.

Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

To avoid compatibility issue with older kernels the firmware doesn't
allow SRQ to work with ODP unless kernel asks for it.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>

The device capabilities for ODP structure was missing the field for XRC
transport so add it here.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>

Calling pci_enable_atomic_ops_to_root enables AtomicOp requests to pci
root port.

AtomicOp requests will be enabled only if the completer and all
intermediate pci bridges support PCI atomic operations.
This, together with appropriate settings in the NVCONFIG should enable
PCI atomic operations on the device.

PCI atomic operations were first introduced in PCI Express Base Specification
2.1. The Supported operations are Swap (Unconditional Swap), CAS (Compare and
Swap) and FetchAdd (Fetch and Add).

Unlike other atomic operation modes PCI atomic operations gives the user
the option to do atomic operations on local memory, without involving verbs
api, without it compromising the operation's atomicity.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>

APIs that have deferred callbacks should have some kind of cleanup
function that callers can use to fence the callbacks. Otherwise things
like module unloading can lead to dangling function pointers, or worse.

The IB MR code is the only place that calls this function and had a
really poor attempt at creating this fence. Provide a good version in
the core code as future patches will add more places that need this
fence.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>

Management Datagram Interface (MAD) is applicable
only when physical port is Infiniband. It makes MAD
command logic to be completely unrelated to eth/core
parts of mlx5.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>

UNAME26 is a mechanism to report Linux's version as 2.6.x, for
compatibility with old/broken software.  Due to the way it is
implemented, it would have to be updated after 5.0, to keep the
resulting versions unique.  Linus Torvalds argued:

 "Do we actually need this?

  I'd rather let it bitrot, and just let it return random versions. It
  will just start again at 2.4.60, won't it?

  Anybody who uses UNAME26 for a 5.x kernel might as well think it's
  still 4.x. The user space is so old that it can't possibly care about
  differences between 4.x and 5.x, can it?

  The only thing that matters is that it shows "2.4.<largeenough>",
  which it will do regardless"
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC fixes from Olof Johansson:
 "A bigger batch than I anticipated this week, for two reasons:

   - Some fallout on Davinci from board file -> DTB conversion, that
     also includes a few longer-standing fixes (i.e. not recent
     regressions).

   - drivers/reset material that has been in linux-next for a while, but
     didn't get sent to us until now for a variety of reasons
     (maintainer out sick, holidays, etc). There's a functional
     dependency in there such that one platform (Altera's SoCFPGA) won't
     boot without one of the patches; instead of reverting the patch
     that got merged, I looked at this set and decided it was small
     enough that I'll pick it up anyway. If you disagree I can revisit
     with a smaller set.

  That being said, there's also a handful of the usual stuff:

   - Fix for a crash on Armada 7K/8K when the kernel touches
     PSCI-reserved memory

   - Fix for PCIe reset on Macchiatobin (Armada 8K development board,
     what this email is sent from in fact :)

   - Enable a few new-merged modules for Amlogic in arm64 defconfig

   - Error path fixes on Integrator

   - Build fix for Renesas and Qualcomm

   - Initialization fix for Renesas RZ/G2E

  .. plus a few more fixlets"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
  ARM: integrator: impd1: use struct_size() in devm_kzalloc()
  qcom-scm: Include <linux/err.h> header
  gpio: pl061: handle failed allocations
  ARM: dts: kirkwood: Fix polarity of GPIO fan lines
  arm64: dts: marvell: mcbin: fix PCIe reset signal
  arm64: dts: marvell: armada-ap806: reserve PSCI area
  ARM: dts: da850-lcdk: Correct the sound card name
  ARM: dts: da850-lcdk: Correct the audio codec regulators
  ARM: dts: da850-evm: Correct the sound card name
  ARM: dts: da850-evm: Correct the audio codec regulators
  ARM: davinci: omapl138-hawk: fix label names in GPIO lookup entries
  ARM: davinci: dm644x-evm: fix label names in GPIO lookup entries
  ARM: davinci: dm355-evm: fix label names in GPIO lookup entries
  ARM: davinci: da850-evm: fix label names in GPIO lookup entries
  ARM: davinci: da830-evm: fix label names in GPIO lookup entries
  arm64: defconfig: enable modules for amlogic s400 sound card
  reset: uniphier-glue: Add AHCI reset control support in glue layer
  dt-bindings: reset: uniphier: Add AHCI core reset description
  reset: uniphier-usb3: Rename to reset-uniphier-glue
  dt-bindings: reset: uniphier: Replace the expression of USB3 with generic peripherals
  ...

Pull btrfs fixes from David Sterba:

 - two regression fixes in clone/dedupe ioctls, the generic check
   callback needs to lock extents properly and wait for io to avoid
   problems with writeback and relocation

 - fix deadlock when using free space tree due to block group creation

 - a recently added check refuses a valid fileystem with seeding device,
   make that work again with a quickfix, proper solution needs more
   intrusive changes

* tag 'for-5.0-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: Use real device structure to verify dev extent
  Btrfs: fix deadlock when using free space tree due to block group creation
  Btrfs: fix race between reflink/dedupe and relocation
  Btrfs: fix race between cloning range ending at eof and writeback

Pull driver core fixes from Greg KH:
 "Here is one small sysfs change, and a documentation update for 5.0-rc2

  The sysfs change moves from using BUG_ON to WARN_ON, as discussed in
  an email thread on lkml while trying to track down another driver bug.
  sysfs should not be crashing and preventing people from seeing where
  they went wrong. Now it properly recovers and warns the developer.

  The documentation update removes the use of BUS_ATTR() as the kernel
  is moving away from this to use the specific BUS_ATTR_RW() and friends
  instead. There are pending patches in all of the different subsystems
  to remove the last users of this macro, but for now, don't advertise
  it should be used anymore to keep new ones from being introduced.

  Both have been in linux-next with no reported issues"

* tag 'driver-core-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  Documentation: driver core: remove use of BUS_ATTR
  sysfs: convert BUG_ON to WARN_ON