Add macros to detect GT2/GT3 skus so we can apply the proper OA
configuration later.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>

In earlier iterations of the i915-perf driver we had a number of
callbacks/hooks from other parts of the i915 driver to e.g. notify us
when a legacy context was pinned and these could run asynchronously with
respect to the stream file operations and might also run in atomic
context.

dev_priv->perf.hook_lock had been for serialising access to state needed
within these callbacks, but as the code has evolved some of the hooks
have gone away or are implemented to avoid needing to lock any state.

The remaining use of this lock was actually redundant considering how
the gen7 oacontrol state used to be updated as part of a context pin
hook.
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>

An oa_exponent_to_ns() utility and per-gen timebase constants where
recently removed when updating the tail pointer race condition WA, and
this restores those so we can update the _PROP_OA_EXPONENT validation
done in read_properties_unlocked() to not assume we have a 12.5MHz
timebase as we did for Haswell.

Accordingly the oa_sample_rate_hard_limit value that's referenced by
proc_dointvec_minmax defining the absolute limit for the OA sampling
frequency is now initialized to (timestamp_frequency / 2) instead of the
6.25MHz constant for Haswell.

v2:
    Specify frequency of 19.2MHz for BXT (Ville)
    Initialize oa_sample_rate_hard_limit per-gen too (Lionel)
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>

These are auto generated from an XML description of metric sets,
currently maintained in gputop, ref:

 https://github.com/rib/gputop
 > gputop-data/oa-*.xml
 > scripts/i915-perf-kernelgen.py

 $ make -C gputop-data -f Makefile.xml
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>

Enables access to OA unit metrics for BDW, CHV, SKL and BXT which all
share (more-or-less) the same OA unit design.

Of particular note in comparison to Haswell: some OA unit HW config
state has become per-context state and as a consequence it is somewhat
more complicated to manage synchronous state changes from the cpu while
there's no guarantee of what context (if any) is currently actively
running on the gpu.

The periodic sampling frequency which can be particularly useful for
system-wide analysis (as opposed to command stream synchronised
MI_REPORT_PERF_COUNT commands) is perhaps the most surprising state to
have become per-context save and restored (while the OABUFFER
destination is still a shared, system-wide resource).

This support for gen8+ takes care to consider a number of timing
challenges involved in synchronously updating per-context state
primarily by programming all config state from the cpu and updating all
current and saved contexts synchronously while the OA unit is still
disabled.

The driver intentionally avoids depending on command streamer
programming to update OA state considering the lack of synchronization
between the automatic loading of OACTXCONTROL state (that includes the
periodic sampling state and enable state) on context restore and the
parsing of any general purpose BB the driver can control. I.e. this
implementation is careful to avoid the possibility of a context restore
temporarily enabling any out-of-date periodic sampling state. In
addition to the risk of transiently-out-of-date state being loaded
automatically; there are also internal HW latencies involved in the
loading of MUX configurations which would be difficult to account for
from the command streamer (and we only want to enable the unit when once
the MUX configuration is complete).

Since the Gen8+ OA unit design no longer supports clock gating the unit
off for a single given context (which effectively stopped any progress
of counters while any other context was running) and instead supports
tagging OA reports with a context ID for filtering on the CPU, it means
we can no longer hide the system-wide progress of counters from a
non-privileged application only interested in metrics for its own
context. Although we could theoretically try and subtract the progress
of other contexts before forwarding reports via read() we aren't in a
position to filter reports captured via MI_REPORT_PERF_COUNT commands.
As a result, for Gen8+, we always require the
dev.i915.perf_stream_paranoid to be unset for any access to OA metrics
if not root.

v5: Drain submitted requests when enabling metric set to ensure no
    lite-restore erases the context image we just updated (Lionel)

v6: In addition to drain, switch to kernel context & update all
    context in place (Chris)

v7: Add missing mutex_unlock() if switching to kernel context fails
    (Matthew)

v8: Simplify OA period/flex-eu-counters programming by using the
    batchbuffer instead of modifying ctx-image (Lionel)

v9: Back to updating the context image (due to erroneous testing,
    batchbuffer programming the OA unit doesn't actually work)
    (Lionel)
    Pin context before updating context image (Chris)
    Drop MMIO programming now that we switch to a kernel context with
    right values in initial context image (Chris)

v10: Just pin_map the contexts we want to modify or let the
     configuration happen on first use (Chris)

v11: Update kernel context OA config through the batchbuffer rather
     than on the fly ctx-image update (Lionel)

v12: Rework OA context registers update again by swithing away from
     user contexts and reconfiguring the kernel context through the
     batchbuffer and updating all the other contexts' context image.
     Also take care to lock slice/subslice configuration when OA is
     on. (Lionel)

v13: Request rpcs updates on all engine when updating the OA config
     (Lionel)

v14: Drop any kind of rpcs management now that we monitor sseu
     configuration changes in a later patch (Lionel)
     Remove usleep after programming the NOA configs on Gen8+, this
     doesn't seem to be needed (Lionel)

v15: Respect coding style for block comments (Chris)

v16: Add missing i915_add_request() in case we fail to emit OA
     configuration (Matthew)
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com> \o/
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>

Adds a static OA unit, MUX, B Counter + Flex EU configurations for basic
render metrics on Broadwell, Cherryview, Skylake and Broxton. These are
auto generated from an XML description of metric sets, currently
maintained in gputop, ref:

 https://github.com/rib/gputop
 > gputop-data/oa-*.xml
 > scripts/i915-perf-kernelgen.py

 $ make -C gputop-data -f Makefile.xml WHITELIST=RenderBasic

v2: add newlines to debug messages + fix comment (Matthew Auld)
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>

Gen8+ might have mux configurations per slices/subslices. Depending on
whether slices/subslices have been fused off, only part of the
configuration needs to be applied. This change reworks the mux
configurations query mechanism to allow more than one set of registers
to be programmed.

v2: s/n_mux_regs/n_mux_configs/ (Matthew)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>

Assuming a uniform mask across all slices, this enables userspace to
determine the specific sub slices can be enabled. This information is
required, for example, to be able to analyse some OA counter reports
where the counter configuration depends on the HW sub slice
configuration.
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>

Enables userspace to determine the maximum number of slices that can
be enabled on the device and also know what specific slices can be
enabled. This information is required, for example, to be able to
analyse some OA counter reports where the counter configuration
depends on the HW slice configuration.
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>

I removed the zapping of the reservation_object->fence array of shared
fences prematurely. We don't yet have the code to zap that array when
retiring the object, and so currently it remains possible to continually
grow the shared array trapping requests when reusing the batch_pool
object across many timelines.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170518094638.5469-4-chris@chris-wilson.co.uk

Having resolved whether or not we would deadlock upon a call to
mutex_lock(&dev->struct_mutex), we can then spin for the contended
struct_mutex if we are not the owner. We cannot afford to simply block
and wait for the mutex, as the owner may itself be waiting for the
allocator -- i.e. a cyclic deadlock. This should significantly improve
the chance of running the shrinker for other processes whilst the GPU is
busy.

A more balanced approach would be to optimistically spin whilst the
mutex owner was on the cpu and there was an opportunity to acquire the
mutex for ourselves quickly. However, that requires support from
kernel/locking/ and a new mutex_spin_trylock() primitive.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170609110350.1767-4-chris@chris-wilson.co.ukReviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

In our first pass, we do not want to use reclaim at all as we want to
solely reap the i915 buffer caches (its purgeable pages). But we don't
mind it initiates IO or pulls via the FS (but it shouldn't anyway as we
say no to reclaim!). Just drop the GFP_IO constraint for simplicity.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170609110350.1767-3-chris@chris-wilson.co.ukReviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

I tried __GFP_NORETRY in the belief that __GFP_RECLAIM was effective. It
struggles with handling reclaim of our dirty buffers and relies on
reclaim via kswapd. As a result, a single pass of direct reclaim is
unreliable when i915 occupies the majority of available memory, and the
only means of effectively waiting on kswapd to amke progress is by not
setting the __GFP_NORETRY flag and lopping. That leaves us with the
dilemma of invoking the oomkiller instead of propagating the allocation
failure back to userspace where it can be handled more gracefully (one
hopes).  In the future we may have __GFP_MAYFAIL to allow repeats up until
we genuinely run out of memory and the oomkiller would have been invoked.
Until then, let the oomkiller wreck havoc.

v2: Stop playing with side-effects of gfp flags and await __GFP_MAYFAIL
v3: Update comments that direct reclaim only appears to be ignoring our
dirty buffers!

Fixes: 24f8e00a ("drm/i915: Prefer to report ENOMEM rather than incur the oom for gfx allocations")
Testcase: igt/gem_tiled_swapping
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Michal Hocko <mhocko@suse.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170609110350.1767-2-chris@chris-wilson.co.ukReviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

Commit 24f8e00a ("drm/i915: Prefer to report ENOMEM rather than
incur the oom for gfx allocations") made the bold decision to try and
avoid the oomkiller by reporting -ENOMEM to userspace if our allocation
failed after attempting to free enough buffer objects. In short, it
appears we were giving up too easily (even before we start wondering if
one pass of reclaim is as strong as we would like). Part of the problem
is that if we only shrink just enough pages for our expected allocation,
the likelihood of those pages becoming available to us is less than 100%
To counter-act that we ask for twice the number of pages to be made
available. Furthermore, we allow the shrinker to pull pages from the
active list in later passes.

v2: Be a little more cautious in paging out gfx buffers, and leave that
to a more balanced approach from shrink_slab(). Important when combined
with "drm/i915: Start writeback from the shrinker" as anything shrunk is
immediately swapped out and so should be more conservative.

Fixes: 24f8e00a ("drm/i915: Prefer to report ENOMEM rather than incur the oom for gfx allocations")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170609110350.1767-1-chris@chris-wilson.co.uk

All here is pretty much like Kabylake.

Including CFL-U has to use same ddi translation table
as KBL-U for now.

v2: Include missed IS_COFFEELAKE on edp trans table. (DK)
    Handle CFL-U with same translation table as KBL-U. (DK and
    confirmed with HW engineers)

v3: Adding missed case for IS_CFL_ULT. (DK).

v4: Duh! Now with the real IS_CFL_ULT instead of KBL one. (DK)
    Also use IS_GEN9_BC when possible. (DK)

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497045770-21302-1-git-send-email-rodrigo.vivi@intel.com

Enable wrpll computation for Cannonlake platform to support
pll's required for HDMI output. The patch contains the following features

- compute Cannonlake port clock programming
  dividers P, Q, and K.
- compute PLL parameters for Cannonlake. These parameters
  set the values on DPLL registers.
- find the register values to program wrpll for Cannonlake.
  The reference clock can be either 19.2MHz or 24MHz.

v2: rebase
v3: squash wrpll patches into one (Rodrigo)
v4: switch order of getting even dividers (Paulo)
    update divider register values for PDiv and KDiv (Paulo)
    update wrpll computation algorithm (Paulo)
v5: Remove ref clock division by 1000. (Rodrigo)
v6: Rodrigo rebasing on top of latest code.
Signed-off-by: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-18-git-send-email-rodrigo.vivi@intel.com

There is no platform specific change needed for LSPCON
support on Cannonlake. So let's make it gen9+.

Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-17-git-send-email-rodrigo.vivi@intel.com

Also in a way that reuse bdw+ for all next platforms.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-16-git-send-email-rodrigo.vivi@intel.com

As Geminilake scalers Cannonlake also don't need and don't have
the "high quality" mode programming.

Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-15-git-send-email-rodrigo.vivi@intel.com

Since we have HAS_CSR tied to the platform definition
let's use this instead of checking per platform.

One less thing to worry when adding support to new platforms.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Animesh Manna<animesh.manna@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-14-git-send-email-rodrigo.vivi@intel.com

This patch loads the DMC on CNL.The firmware version
is 1.04.

v2: (Rodrigo) Remove MODULE_FIRMWARE.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-13-git-send-email-rodrigo.vivi@intel.com

vswing programming sequence step 2 requires the Loadgen_select bit to
be set in PORT_TX_DW4 lane reigsters per table defined by Bit rate and
lane width. Implemented the change that was marked as FIXME in the
driver.

v2: (Rodrigo) checkpatch fixes.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-12-git-send-email-rodrigo.vivi@intel.com

This is an important part of the DDI initalization as well as
for changing the voltage during DisplayPort link training.

This new sequence for Cannonlake is more like Broxton style
but still with different registers, different table and
different steps.

v2: Do not write to DW4_GRP to avoid overwrite individual loadgen.
    Fix PORT_CL_DW5 SUS Clock Config set.
v3: As previous platforms use only eDP table if low voltage was
    requested.
v4: fix Werror:maybe uninitialized (Paulo)
v5: Rebase on top of dw2_swing_sel changes
    on previous patches.
v6: Using flexible SCALING_MODE_SEL(x).

Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-11-git-send-email-rodrigo.vivi@intel.com

These tables are used on voltage wswing sequence initialization
on Cannonlake.

It is a complete new format now in use by the voltage swing team,
not following any other standard in use by any other platform.
Also the registers are different as well. So let's redefine
the translation table for Cannonlake.

The table is huge. So we minimized with the fields that are
different or might be different anytime soon. The common
values will be hardcoded on the voltage swing sequence.

v2: Merge the lower and the upper bits to match the spec table
    and make review easier. This was possible with the good
    idea for Manasi with a better way to handle it on the bit
    macro definition presented on previous patch.
    Credits-to: Manasi

Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-10-git-send-email-rodrigo.vivi@intel.com

This are the registers and bits needed for the voltage swing
sequence on Cannonlake.

v2: Remove CL_DW5 that was wrongly defined.
v3: Use (1 << 1) instead of (1<<1) as Paulo suggested
    Change DW2 swing sel upper and lower macros to do the
    bit selection instead of definint a table that doesn't
    match the spec. It is based on a Manasi version of it.
    Credits-to: Manasi.
v4: Let SCALING_MODE_SEL flexible. (Manasi)

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-9-git-send-email-rodrigo.vivi@intel.com

Also new registers can have different mmio offsets
per different lane per port.

v2: Use _PICK as PORT3 instead of creating a new
    macro with if per port.
v3: Use _PICK directly on MMIO_PORT6. While MMIO_PORT
    isn't flexible enough let's continue with MMIO_PORT6
    as we have MMIO_PORT3.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-8-git-send-email-rodrigo.vivi@intel.comSigned-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Although CNL follows PLL initialization more like Skylake
than Broxton we have a completely different initialization
sequence and registers used.

One big difference from SKL is that CDCLK PLL is now
exclusive (ADPLL) and for DDIs and MIPI we need to use
DFGPLLs 0, 1 or 2.

v2: Accept all Ander's suggestions and fixes:
    - Registers and bits names prefix
    - Group pll functions
    - bits masks fixes
    - remove read and modify on cfgcr1
    - fix cfgcr0 setup
v3: Set SSC_ENABLE for DP.
    Fix HDMI_MODE cfgcr0.
    Avoid touch cfgcr0 on DP.
    Add missed else on dpll_mgr definition so we use cnl one, not hsw.
v3: Centra freq should be always set to default and change bits
    definitions to (1 << 1) instead of (1<<1). (by Paulo)
v4: Rebased.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Reviewed-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-7-git-send-email-rodrigo.vivi@intel.com

DPLL's are defined in DPCLKA_CFGCR0 register (0x6C200). Let's use these
definitions when computing dpll's for ddi ports.

v2: (Rodrigo) Remove register that was defined in another patch with
    fixed name and more bits.
Signed-off-by: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-6-git-send-email-rodrigo.vivi@intel.com

One of the steps for PLL (un)initialization is to (un)map
the correspondent DDI that is actually using that PLL.

So, let's do this step following the places already stablished
and used so far, although spec put this as part of PLL
initialization sequences.

v2: Use proper prefix on bits names as suggested by Ander.
v3: Add missed "~". Without that the logic was inverted
    so we were disabling interrupts.
    Credits-to: Clinton
    Credits-to: Art
v4: Spec is getting updated to do DDI -> PLL mapping
    and clock on in 2 separated reg writes. (Paulo)
    Also update bits definitions to use space
    (1 << 1) instead of (1<<1). (Paulo)

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Cc: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-5-git-send-email-rodrigo.vivi@intel.com

All the low level cdclk bits are present, so let's add the required
hooks to reconfigure cdclk on the fly.

Cannonlake also needs to adjust the minimal pixel rate
as gen9 platforms. Specially for the Azalia audio case.

v2: Rebase due to cnl_sanitize_cdclk()
v3: Rebased by Rodrigo on top of Ville's cdclk rework.
v4: Rebase moving cnl_calc_cdclk up to follow same order
    as previous platforms.
v2: Squash drm/i915/cnl: Adjust min pixel rate. to address
    the current limitation where CDCLK cannot be set to 168MHz
    if audio is used with 96MHz. (Imre)
v3: adjust some of the clock limits within
    bdw_adjust_min_pipe_pixel_rate. (Ville/DK/Imre).
    Fix commit message messed by squash.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-4-git-send-email-rodrigo.vivi@intel.com

Implement the CNL display init/uninit sequence as outlined in Bspec.

Quite similar to SKL/BXT. The main complicaiton is probably the extra
procmon setup we must do based on the process/voltage information we
can read out from some register.

v2: s/skl_dbuf/gen9_dbuf/ to follow upstream
    bxt needed a cdclk sanitize step, so let's add it for cnl too
v3: s/CHICKEN_MISC_1/CHICKEN_MISC_2/ (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework
v5: Removed unecessary Aux IO forced enable/disable, Fix DW10 setup
    Fix procpon Mask. (Credits-to Paulo and Clint)
    Remove A0 workaround.
v6: Rebased on top of recent code (Rodrigo).
v7: Respect the order of sanitize_ after set_
    (Done by Rodrigo, Requested by Ville)
v8: Commit message updated to matvh v5 changes besides
    Remove unused DW8 and an extra blank line. (all noticed
    by Imre).
v9: Remove __attribute__((unused)) added on latest version
    of drm/i915/cnl: Implement .set_cdclk() for CNL.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-3-git-send-email-rodrigo.vivi@intel.com

Add support for changing the cdclk frequency on CNL. Again, quite
similar to BXT, but there are some annoying differences which means
trying to share more code might not be feasible:
* PLL ratio now lives in the PLL enable register
* pcode came from SKL, not from BXT

We support three cdclk frequencies: 168,336,528 Mhz. The first two
use the same PLL frequency, the last one uses a different one meaning
we once again may need to toggle the PLL off and on when changing
cdclk.

v2: Rebased by Rodrigo on top of Ville's cdclk rework.
v3: Respect order of set_ bellow get_ (Ville)
v4: Added __attribute__((unused)) to avoid broken compilation with Werror.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-2-git-send-email-rodrigo.vivi@intel.com

Add support for reading out the cdclk frequency from the hardware on
CNL. Very similar to BXT, with a few new twists and turns:
* the PLL is now called CDCLK PLL, not DE PLL
* reference clock can be 24 MHz in addition to the 19.2 MHz BXT had
* the ratio now lives in the PLL enable register
* Only 1x and 2x CD2X dividers are supported

v2: Deal with PLL lock bit the same way as BXT/SKL do now
v3: DSSM refclk indicator is bit 31 not 24 (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework.
v5: Set cdclk to the ref clock as previous platforms. (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-1-git-send-email-rodrigo.vivi@intel.com

Pass crtc_state to the enable callback, and connector_state to all callbacks.
This will eliminate the need to guess for the correct pipe in these
callbacks.

The crtc state is required for pch_enable_backlight to obtain the correct
cpu_transcoder.

intel_dp_aux_backlight's setup function is called before hw readout, so
crtc_state and connector_state->best_encoder are NULL in the enable()
and set() callbacks.

This fixes the following series of warns from intel_get_pipe_from_connector:
[  219.968428] ------------[ cut here ]------------
[  219.968481] WARNING: CPU: 3 PID: 2457 at
drivers/gpu/drm/i915/intel_display.c:13881
intel_get_pipe_from_connector+0x62/0x90 [i915]
[  219.968483]
WARN_ON(!drm_modeset_is_locked(&dev->mode_config.connection_mutex))
[  219.968485] Modules linked in: nls_iso8859_1 snd_hda_codec_hdmi
snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec
snd_hda_core snd_hwdep snd_pcm intel_rapl x86_pkg_temp_thermal coretemp
kvm_intel snd_seq_midi snd_seq_midi_event kvm snd_rawmidi irqbypass
crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc snd_seq
snd_seq_device serio_raw snd_timer aesni_intel aes_x86_64 crypto_simd
glue_helper cryptd lpc_ich snd mei_me shpchp soundcore mei rfkill_gpio
mac_hid intel_pmc_ipc parport_pc ppdev lp parport ip_tables x_tables
autofs4 hid_generic usbhid igb ahci i915 xhci_pci dca xhci_hcd ptp
sdhci_pci sdhci libahci pps_core i2c_hid hid video
[  219.968573] CPU: 3 PID: 2457 Comm: kworker/u8:3 Tainted: G        W
4.10.0-tip-201703010159+ #2
[  219.968575] Hardware name: Intel Corp. Broxton P/NOTEBOOK, BIOS
APLKRVPA.X64.0144.B10.1606270006 06/27/2016
[  219.968627] Workqueue: events_unbound intel_atomic_commit_work [i915]
[  219.968629] Call Trace:
[  219.968640]  dump_stack+0x63/0x87
[  219.968646]  __warn+0xd1/0xf0
[  219.968651]  warn_slowpath_fmt+0x4f/0x60
[  219.968657]  ? drm_printk+0x97/0xa0
[  219.968708]  intel_get_pipe_from_connector+0x62/0x90 [i915]
[  219.968756]  intel_panel_enable_backlight+0x19/0xf0 [i915]
[  219.968804]  intel_edp_backlight_on.part.22+0x33/0x40 [i915]
[  219.968852]  intel_edp_backlight_on+0x18/0x20 [i915]
[  219.968900]  intel_enable_ddi+0x94/0xc0 [i915]
[  219.968950]  intel_encoders_enable.isra.93+0x77/0x90 [i915]
[  219.969000]  haswell_crtc_enable+0x310/0x7f0 [i915]
[  219.969051]  intel_update_crtc+0x58/0x100 [i915]
[  219.969101]  skl_update_crtcs+0x218/0x240 [i915]
[  219.969153]  intel_atomic_commit_tail+0x350/0x1000 [i915]
[  219.969159]  ? vtime_account_idle+0xe/0x50
[  219.969164]  ? finish_task_switch+0x107/0x250
[  219.969214]  intel_atomic_commit_work+0x12/0x20 [i915]
[  219.969219]  process_one_work+0x153/0x3f0
[  219.969223]  worker_thread+0x12b/0x4b0
[  219.969227]  kthread+0x101/0x140
[  219.969230]  ? rescuer_thread+0x340/0x340
[  219.969233]  ? kthread_park+0x90/0x90
[  219.969237]  ? do_syscall_64+0x6e/0x180
[  219.969243]  ret_from_fork+0x2c/0x40
[  219.969246] ---[ end trace 0a8fa19387b9ad6d ]---

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100022Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170612102115.23665-4-maarten.lankhorst@linux.intel.comReviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

Passing the state is also needed to convert the backlight functions
to use the correct state instead of looking it up.

This is done as a separate commit to allow easier bisecting.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100022Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170612102115.23665-3-maarten.lankhorst@linux.intel.comReviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

The backlight functions need to determine the pipe and the transcoder the
backlight will be enabled on, so pass crtc_state instead of trying to
dereference the state without holding locks.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100022Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170612102115.23665-2-maarten.lankhorst@linux.intel.comReviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

Current it's strictly checked if PVINFO version matches 1.0
for GVT-g i915 guest which doesn't help for compatibility at
all and forces GVT-g host can't extend PVINFO easily with version
bump for real compatibility check.

This fixes that to check minimal required PVINFO version instead.

v2:
- drop unneeded version macro
- use only major version for sanity check

v3:
- fix up PVInfo value with kernel type
- one indent fix
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170609074805.5101-1-zhenyuw@linux.intel.com

both platforms. We haven't recieved any separated release
specifically for Coffee Lake so let's just re-use what
is already there for Kabylake.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497038550-30910-1-git-send-email-rodrigo.vivi@intel.com

Coffee Lake reuses Kabylake's HUC firmware.

v2: Change Coffeelake to Coffee Lake

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Lukasz Fiedorowicz <lukasz.fiedorowicz@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496965704-23610-2-git-send-email-anusha.srivatsa@intel.com

Coffee Lake reuses Kabylake's GuC.

v2: Change Coffeelake to Coffee Lake

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Lukasz Fiedorowicz <lukasz.fiedorowicz@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496965704-23610-1-git-send-email-anusha.srivatsa@intel.com