This patch implements the off-the-shelf probeinit component operation.
Currently, all it does is waking up the PHY if it's a SATA port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

This patch adds probeinit component operation to
ata_drive_probe_reset().  If present, this new operation is called
before performing any reset.  The operations's roll is to prepare @ap
for following probe-reset operations.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

This patch separates out sata_phy_resume() from sata_std_hardreset().
The function will later be used by probeinit callback.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

ap->cbl is initialized during postreset and thus unknown on entry to
ata_std_probe_reset().  This patch makes ata_std_probe_reset() use
ATA_FLAG_SATA flag instead of ap->cbl to detect SATA port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

This patch makes sure that pio tasks are flushed before proceeding
with EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

ATA_FLAG_IN_EH flag is set on entry to EH and cleared on completion.
This patch just sets and clears the flag.  Following patches will
build normal qc execution / EH synchronization aroung this flag.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

If you set network interface down and up again, the IPv6 address
autoconfiguration does not work. 'ip addr' shows that the link-local
address is in tentative state. We don't even react to periodical router
advertisements.

During NETDEV_DOWN we clear IF_READY, and we don't set it back in
NETDEV_UP. While starting to perform DAD on the link-local address, we
notice that the device is not in IF_READY, and we abort autoconfiguration
process (which would eventually send router solicitations).
Acked-by: Juha-Matti Tapio <jmtapio@verkkotelakka.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add unshare syscall for x86-64

ppoll/pselect are not ready yet, but add reservations.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Manual conflict merge of arch/arm/Kconfig

An obvious vi fat finger on my part.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Tony Lindgren

This patch fixes the low-level IO init for omap2 boards.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Tony Lindgren

This patch fixes the low-level IO init for omap1 boards.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Tony Lindgren

This patch adds the missing cache flushes to common low-level
init that are needed to access the IO region. These flushes
are normally done at the end of devicemaps_init(), but we
need to detect the OMAP core type early.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Change the IRQ resource range for the ADC device
to be two distinct IRQs
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch adds new PCI serial card support.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This replaces old direct usage of tty->flip stuff with relative flip API
calls.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The DB1550 actually doesn't have a UART2.  Remove it from the list.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

On some embedded PowerPC (MPC834x) systems an extra byte would some
times be required to flush data out of the fifo.
serial8250_console_write() was updating the IER in hardware without
also updating the copy in uart_8250_port. This causes issues functions
like serial8250_start_tx() and __stop_tx() to misbehave.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Lucas Correia Villa Real

This patch defines the number of serial ports on the S3C2400.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Catalin Marinas

Because of a type, OSC1 was used for setting the display clock instead of
OSC4. This patch fixes it.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

Since:

	if (unlikely(__res || __ex_flag))

produces worse code on ARM than:

	if (unlikely(__res | __ex_flag))

I therefore made it more explicit:

	__res |= __ex_flag;
	if (unlikely(__res != 0))

so it is not seen as a typo again.

Also made everything static inline rather than macros for better readability
(both produce the same code after all).

And finally added missing \t from multi-line assembly code.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

 negative

Patch from Nicolas Pitre

The pre ARMv5 implementation can be aborted if an exception occurs in
the middle of it.  Because of that, the ARMv6 implementation doesn't
re-attempt the operation on a failed strex either.  Let's make this
transient nature of such a false positive more explicit in the
definition.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

The cmpxchg emulation on pre-ARMv5 relies on user code executed from a
kernel address.  If the operation cannot complete atomically, it is
aborted from the usr_entry macro by clearing the Z flag.  This clearing
of the Z flag is done whenever the user pc is above TASK_SIZE.

However this "pc >= TASK_SIZE" test cannot work in the non MMU case.
Worse: the current code will corrupt the Z flag on every entry to the
kernel.

Let's disable it in the non MMU case for now.  Using NPTL on non MMU
targets needs to be worked out anyway.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

struct sockaddr_un loses its padding with EABI.  Since the size of the
structure is used as a validation test in unix_mkname(), we need to
change the length argument to 110 whenever it is 112.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

Although OABI_COMPAT works fine in most cases, it is still experimental
and could be for ever since it is nearly impossible to handle
everything, e.g. ioctls.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Bring s3c2410 defconfig up to date
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Martin Michlmayr

Minor typographical and spelling fixes in Konfig
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>

---

 Kconfig |    8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Martin Michlmayr

Add help descriptions to ARCH config items that don't have one.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>

---

 Kconfig               |   32 ++++++++++++++++++++++++++++++--
 mach-clps711x/Kconfig |    2 ++
 2 files changed, 32 insertions(+), 2 deletions(-)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Move to using an enable count for the shared clocks
and protect the clock system using a mutex instead
of just disabling IRQs during the clock update.

Since there is little more code in the path for
non-shared clocks, the enable and disable calls
use the same code for each.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

Most ixp2000 boards don't actually work if pci=firmware isn't used, so
the defconfig isn't really the right place to specify this.  Instead of
specifying it in the defconfigs, make the relevant board code take care
of setting pci=firmware.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>