- 18 Dec, 2017 12 commits
-
-
Alex Deucher authored
add device to the name for consistency. Acked-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Alex Deucher authored
add device to the name for consistency. Acked-by:
-
Alex Deucher authored
It's the only place they are used. Acked-by:
-
Alex Deucher authored
add device to the name for consistency. Acked-by:
-
Alex Deucher authored
It's the only place it's used. Acked-by:
-
Alex Deucher authored
add device for consistency with other functions in this file. Acked-by:
-
Alex Deucher authored
add device for consistency with other functions in this file. Acked-by:
-
Alex Deucher authored
add device for consistency. Acked-by:
-
Alex Deucher authored
amdgpu_device.c was getting pretty cluttered. Acked-by:
-
Alex Deucher authored
for consistency with the other functions in that file. Acked-by:
-
Alex Deucher authored
Prefix the functions with device or device_ip for functions which deal with ip blocks for consistency. Acked-by:
-
Alex Deucher authored
and move them to amdgpu_atombios.c for consistency. Acked-by:
-
- 15 Dec, 2017 8 commits
-
-
Colin Ian King authored
The null check on aconnector->base.edid_blob_ptr->data is redundant since data is an array and can never be null. Remove it. Detected by CoverityScan, CID#1460369 ("Array compared against 0") Acked-by:Harry Wentland <harry.wentland@amd.com> Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Alex Deucher authored
Same as previous asics. This was not yet set for gfx9. Acked-by:
-
Andrey Grodzovsky authored
With introduction of amdgpu_gpu_recovery we don't need any more to rely on amdgpu_lockup_timeout == 0 for disabling GPU reset. Signed-off-by:
Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by:
-
Andrey Grodzovsky authored
Add new parameter to control GPU recovery procedure. v2: Add auto logic where reset is disabled for bare metal and enabled for SR-IOV. Allow forced reset from debugfs. Signed-off-by:
-
Roger He authored
include ttm_bo_move_memcpy and ttm_bo_move_ttm Signed-off-by:
Roger He <Hongbo.He@amd.com> Reviewed-by:
-
Roger He authored
allow eviction of BOs reserved by the caller when they are not part of the current working set. Reviewed-by:
-
Roger He authored
enable eviction of other per VM BOs during allocation and allows reaping of deleted BOs during CS. Reviewed-by:
Chunming Zhou <david1.zhou@amd.com> Reviewed-by:
-
Roger He authored
allow_reserved_eviction: Allow eviction of reserved BOs resv: Reservation object to allow reserved evictions with Reviewed-by:
-
- 14 Dec, 2017 20 commits
-
-
Chunming Zhou authored
v2: remove SUBPTB member v3: remove last_level, use AMDGPU_VM_PTB directly instead. Signed-off-by:
-
Tony Cheng authored
Signed-off-by:
Tony Cheng <tony.cheng@amd.com> Reviewed-by:
-
Harry Wentland authored
Signed-off-by:
Jordan Lazare <Jordan.Lazare@amd.com> Acked-by:
-
Harry Wentland authored
Signed-off-by:
-
Harry Wentland authored
We already check this a couple lines earlier. Signed-off-by:
-
Dmytro Laktyushkin authored
Signed-off-by:
Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by:
-
Yue Hin Lau authored
Signed-off-by:
Yue Hin Lau <Yuehin.Lau@amd.com> Reviewed-by:
Eric Bernstein <Eric.Bernstein@amd.com> Acked-by:
-
Yongqiang Sun authored
It may take over 200ms for wait hpd ready. To optimize the resume time, we can power on eDP in init_hw, wait for hpd ready when doing link training. also create separate eDP enable function to make sure eDP is powered up before doing and DPCD access, as HPD low will result in DPDC transaction failure. After optimization, setpowerstate 145ms -> 9.8ms, DPMS 387ms -> 18.9ms Signed-off-by:
Yongqiang Sun <yongqiang.sun@amd.com> Signed-off-by:
-
Eric Yang authored
Signed-off-by:
Eric Yang <Eric.Yang2@amd.com> Reviewed-by:
Andrew Jiang <Andrew.Jiang@amd.com> Acked-by:
-
Eric Bernstein authored
Move OPP initialization of mpc tree parameters to hw_init function. Signed-off-by:
-
Eric Bernstein authored
Use REG_UPDATE instead of REG_SET for programming MPC out mux. Signed-off-by:
-
Vitaly Prosyak authored
When convert from fixed31_32 to other fixed point format use math operation round instead of floor. Signed-off-by:
Vitaly Prosyak <vitaly.prosyak@amd.com> Reviewed-by:
Roman Li <Roman.Li@amd.com> Reviewed-by:
Krunoslav Kovac <Krunoslav.Kovac@amd.com> Acked-by:
-
Yue Hin Lau authored
Signed-off-by:
-
Vitaly Prosyak authored
Also handle fixpoint y values for CM curves Signed-off-by:
-
Yue Hin Lau authored
Signed-off-by:
-
Dmytro Laktyushkin authored
This reverts commit 978482d0de86 Revert noisy assert messages Signed-off-by:
-
Dmytro Laktyushkin authored
Signed-off-by:
-
Dmytro Laktyushkin authored
Signed-off-by:
-
Harry Wentland authored
This has proven helpful on other OSes to give a quick state of the DC driver when a bug is reported. Signed-off-by:
-
Tony Cheng authored
REG_UPDATE_2 return the reg value it write out through MMIO we need to do a REG_READ to confirm the value is written out Signed-off-by:
-
