- 24 Jun, 2016 40 commits
-
-
Thomas Huth authored
commit 7cc85103 upstream. If we do not provide the PVR for POWER8NVL, a guest on this system currently ends up in PowerISA 2.06 compatibility mode on KVM, since QEMU does not provide a generic PowerISA 2.07 mode yet. So some new instructions from POWER8 (like "mtvsrd") get disabled for the guest, resulting in crashes when using code compiled explicitly for POWER8 (e.g. with the "-mcpu=power8" option of GCC). Fixes: ddee09c0 ("powerpc: Add PVR for POWER8NVL processor") Signed-off-by:
Thomas Huth <thuth@redhat.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thomas Huth authored
commit 8dd75ccb upstream. We are already using the privileged versions of MMCR0, MMCR1 and MMCRA in the kernel, so for MMCR2, we should better use the privileged versions, too, to be consistent. Fixes: 240686c1 ("powerpc: Initialise PMU related regs on Power8") Suggested-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
-
Thomas Huth authored
commit d23fac2b upstream. The SIAR and SDAR registers are available twice, one time as SPRs 780 / 781 (unprivileged, but read-only), and one time as the SPRs 796 / 797 (privileged, but read and write). The Linux kernel code currently uses the unprivileged SPRs - while this is OK for reading, writing to that register of course does not work. Since the KVM code tries to write to this register, too (see the mtspr in book3s_hv_rmhandlers.S), the contents of this register sometimes get lost for the guests, e.g. during migration of a VM. To fix this issue, simply switch to the privileged SPR numbers instead. Signed-off-by:
-
Russell Currey authored
commit 871e178e upstream. In the "ibm,configure-pe" and "ibm,configure-bridge" RTAS calls, the spec states that values of 9900-9905 can be returned, indicating that software should delay for 10^x (where x is the last digit, i.e. 990x) milliseconds and attempt the call again. Currently, the kernel doesn't know about this, and respecting it fixes some PCI failures when the hypervisor is busy. The delay is capped at 0.2 seconds. Signed-off-by:
Russell Currey <ruscur@russell.cc> Acked-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by:
-
Will Deacon authored
commit 0106d456 upstream. Commit 66dbd6e6 ("arm64: Implement ptep_set_access_flags() for hardware AF/DBM") ensured that pte flags are updated atomically in the face of potential concurrent, hardware-assisted updates. However, Alex reports that: | This patch breaks swapping for me. | In the broken case, you'll see either systemd cpu time spike (because | it's stuck in a page fault loop) or the system hang (because the | application owning the screen is stuck in a page fault loop). It turns out that this is because the 'dirty' argument to ptep_set_access_flags is always 0 for read faults, and so we can't use it to set PTE_RDONLY. The failing sequence is: 1. We put down a PTE_WRITE | PTE_DIRTY | PTE_AF pte 2. Memory pressure -> pte_mkold(pte) -> clear PTE_AF 3. A read faults due to the missing access flag 4. ptep_set_access_flags is called with dirty = 0, due to the read fault 5. pte is then made PTE_WRITE | PTE_DIRTY | PTE_AF | PTE_RDONLY (!) 6. A write faults, but pte_write is true so we get stuck The solution is to check the new page table entry (as would be done by the generic, non-atomic definition of ptep_set_access_flags that just calls set_pte_at) to establish the dirty state. Fixes: 66dbd6e6 ("arm64: Implement ptep_set_access_flags() for hardware AF/DBM") Reviewed-by:
Catalin Marinas <catalin.marinas@arm.com> Reported-by:
Alexander Graf <agraf@suse.de> Tested-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Catalin Marinas authored
commit e47b020a upstream. This patch brings the PER_LINUX32 /proc/cpuinfo format more in line with the 32-bit ARM one by providing an additional line: model name : ARMv8 Processor rev X (v8l) Acked-by:
-
Tom Lendacky authored
commit ab6a11a7 upstream. The ccp-crypto module for AES XTS support has a bug that can allow requests greater than 4096 bytes in size to be passed to the CCP hardware. The CCP hardware does not support request sizes larger than 4096, resulting in incorrect output. The request should actually be handled by the fallback mechanism instantiated by the ccp-crypto module. Add a check to insure the request size is less than or equal to the maximum supported size and use the fallback mechanism if it is not. Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Arnd Bergmann authored
commit bad6a185 upstream. In some rare randconfig builds, we can end up with ASYMMETRIC_PUBLIC_KEY_SUBTYPE enabled but CRYPTO_AKCIPHER disabled, which fails to link because of the reference to crypto_alloc_akcipher: crypto/built-in.o: In function `public_key_verify_signature': :(.text+0x110e4): undefined reference to `crypto_alloc_akcipher' This adds a Kconfig 'select' statement to ensure the dependency is always there. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Marc Zyngier authored
commit dd5f1b04 upstream. The INTID mask is wrong, and is made a signed value, which has nteresting effects in the KVM emulation. Let's sanitize it. Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Michael Holzheu authored
commit 0fa96355 upstream. The s390 BFP compiler currently uses relative branch instructions that only support jumps up to 64 KB. Examples are "j", "jnz", "cgrj", etc. Currently the maximum size of s390 BPF programs is set to 0x7ffff. If branches over 64 KB are generated the, kernel can crash due to incorrect code. So fix this an reduce the maximum size to 64 KB. Programs larger than that will be interpreted. Fixes: ce2b6ad9 ("s390/bpf: increase BPF_SIZE_MAX") Signed-off-by:
Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Michael Holzheu authored
commit 6edf0aa4 upstream. In case of usage of skb_vlan_push/pop, in the prologue we store the SKB pointer on the stack and restore it after BPF_JMP_CALL to skb_vlan_push/pop. Unfortunately currently there are two bugs in the code: 1) The wrong stack slot (offset 170 instead of 176) is used 2) The wrong register (W1 instead of B1) is saved So fix this and use correct stack slot and register. Fixes: 9db7f2b8 ("s390/bpf: recache skb->data/hlen for skb_vlan_push/pop") Signed-off-by:
-
Ricardo Ribalda Delgado authored
commit f4833b8c upstream. gpiolib relies on the reference counters to clean up the gpio_device structure. Although the number of get/put is properly aligned on gpiolib.c itself, it does not take into consideration how the referece counters are affected by other external functions such as cdev_add and device_add. Because of this, after the last call to put_device, the reference counter has a value of +3, therefore never calling gpiodevice_release. Due to the fact that some of the device has already been cleaned on gpiochip_remove, the library will end up OOPsing the kernel (e.g. a call to of_gpiochip_find_and_xlate). Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Ricardo Ribalda Delgado authored
commit 11f33a6d upstream. Under some circumstances, a gpiochip might be half cleaned from the gpio_device list. This patch makes sure that the chip pointer is still valid, before calling the match function. [ 104.088296] BUG: unable to handle kernel NULL pointer dereference at 0000000000000090 [ 104.089772] IP: [<ffffffff813d2045>] of_gpiochip_find_and_xlate+0x15/0x80 [ 104.128273] Call Trace: [ 104.129802] [<ffffffff813d2030>] ? of_parse_own_gpio+0x1f0/0x1f0 [ 104.131353] [<ffffffff813cd910>] gpiochip_find+0x60/0x90 [ 104.132868] [<ffffffff813d21ba>] of_get_named_gpiod_flags+0x9a/0x120 ... [ 104.141586] [<ffffffff8163d12b>] gpio_led_probe+0x11b/0x360 Signed-off-by:
-
Ben Dooks authored
commit b66b2a0a upstream. The bcm_kona_gpio_reset() calls bcm_kona_gpio_write_lock_regs() with what looks like the wrong parameter. The write_lock_regs function takes a pointer to the registers, not the bcm_kona_gpio structure. Fix the warning, and probably bug by changing the function to pass reg_base instead of kona_gpio, fixing the following warning: drivers/gpio/gpio-bcm-kona.c:550:47: warning: incorrect type in argument 1 (different address spaces) expected void [noderef] <asn:2>*reg_base got struct bcm_kona_gpio *kona_gpio warning: incorrect type in argument 1 (different address spaces) expected void [noderef] <asn:2>*reg_base got struct bcm_kona_gpio *kona_gpio Signed-off-by:
Ben Dooks <ben.dooks@codethink.co.uk> Acked-by:
Ray Jui <ray.jui@broadcom.com> Reviewed-by:
Markus Mayer <mmayer@broadcom.com> Signed-off-by:
-
Linus Walleij authored
commit 54d77198 upstream. In fdeb8e15 ("gpio: reflect base and ngpio into gpio_device") assumed that GPIO descriptors are either valid or error pointers, but gpiod_get_[index_]optional() actually return NULL descriptors and then all subsequent calls should just bail out. Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Andrew Lunn <andrew@lunn.ch> Fixes: fdeb8e15 ("gpio: reflect base and ngpio into gpio_device") Reported-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Russell King authored
commit e2dfb4b8 upstream. PTRACE_SETVFPREGS fails to properly mark the VFP register set to be reloaded, because it undoes one of the effects of vfp_flush_hwstate(). Specifically vfp_flush_hwstate() sets thread->vfpstate.hard.cpu to an invalid CPU number, but vfp_set() overwrites this with the original CPU number, thereby rendering the hardware state as apparently "valid", even though the software state is more recent. Fix this by reverting the previous change. Fixes: 8130b9d7 ("ARM: 7308/1: vfp: flush thread hwstate before copying ptrace registers") Acked-by:
Simon Marchi <simon.marchi@ericsson.com> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Torsten Hilbrich authored
commit dab38e43 upstream. Tested with Lenovo Ultradock. Fixes the non-working headphone jack on the docking unit. Signed-off-by:
Torsten Hilbrich <torsten.hilbrich@secunet.com> Tested-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Kailang Yang authored
commit 6fbae35a upstream. Support new codecs for ALC700/ALC701/ALC703. Signed-off-by:
Kailang Yang <kailang@realtek.com> Signed-off-by:
-
Kailang Yang authored
commit e69e7e03 upstream. That is some different register for ALC255 and ALC256. ALC256 can't fit with some ALC255 register. This issue is cause from LDO output voltage control. This patch is updated the right LDO register value. Signed-off-by:
-
AceLan Kao authored
commit f90d83b3 upstream. Add the pin configuration value of this machine into the pin_quirk table to make DELL1_MIC_NO_PRESENCE apply to this machine. Signed-off-by:
AceLan Kao <acelan.kao@canonical.com> Signed-off-by:
-
Vinod Koul authored
commit 35639a0e upstream. Kabylake shows up as PCI ID 0xa171. And Kabylake-LP as 0x9d71. Since these are similar to Skylake add these to SKL_PLUS macro Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Julien Grall authored
commit 0f254c76 upstream. The global variable __oprofile_cpu_pmu is set before the PMU is fully initialized. If an error occurs before the end of the initialization, the PMU will be freed and the variable will contain an invalid pointer. This will result in a kernel crash when perf will be used. Fix it by moving the setting of __oprofile_cpu_pmu when the PMU is fully initialized (i.e when it is no longer possible to fail). Signed-off-by:
Julien Grall <julien.grall@arm.com> Acked-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
-
Paolo Bonzini authored
commit c622a3c2 upstream. Found by syzkaller: BUG: unable to handle kernel NULL pointer dereference at 0000000000000120 IP: [<ffffffffa0797202>] kvm_irq_map_gsi+0x12/0x90 [kvm] PGD 6f80b067 PUD b6535067 PMD 0 Oops: 0000 [#1] SMP CPU: 3 PID: 4988 Comm: a.out Not tainted 4.4.9-300.fc23.x86_64 #1 [...] Call Trace: [<ffffffffa0795f62>] irqfd_update+0x32/0xc0 [kvm] [<ffffffffa0796c7c>] kvm_irqfd+0x3dc/0x5b0 [kvm] [<ffffffffa07943f4>] kvm_vm_ioctl+0x164/0x6f0 [kvm] [<ffffffff81241648>] do_vfs_ioctl+0x298/0x480 [<ffffffff812418a9>] SyS_ioctl+0x79/0x90 [<ffffffff817a1062>] tracesys_phase2+0x84/0x89 Code: b5 71 a7 e0 5b 41 5c 41 5d 5d f3 c3 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 8b 8f 10 2e 00 00 31 c0 48 89 e5 <39> 91 20 01 00 00 76 6a 48 63 d2 48 8b 94 d1 28 01 00 00 48 85 RIP [<ffffffffa0797202>] kvm_irq_map_gsi+0x12/0x90 [kvm] RSP <ffff8800926cbca8> CR2: 0000000000000120 Testcase: #include <unistd.h> #include <sys/syscall.h> #include <string.h> #include <stdint.h> #include <linux/kvm.h> #include <fcntl.h> #include <sys/ioctl.h> long r[26]; int main() { memset(r, -1, sizeof(r)); r[2] = open("/dev/kvm", 0); r[3] = ioctl(r[2], KVM_CREATE_VM, 0); struct kvm_irqfd ifd; ifd.fd = syscall(SYS_eventfd2, 5, 0); ifd.gsi = 3; ifd.flags = 2; ifd.resamplefd = ifd.fd; r[25] = ioctl(r[3], KVM_IRQFD, &ifd); return 0; } Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Paolo Bonzini authored
commit d14bdb55 upstream. MOV to DR6 or DR7 causes a #GP if an attempt is made to write a 1 to any of bits 63:32. However, this is not detected at KVM_SET_DEBUGREGS time, and the next KVM_RUN oopses: general protection fault: 0000 [#1] SMP CPU: 2 PID: 14987 Comm: a.out Not tainted 4.4.9-300.fc23.x86_64 #1 Hardware name: LENOVO 2325F51/2325F51, BIOS G2ET32WW (1.12 ) 05/30/2012 [...] Call Trace: [<ffffffffa072c93d>] kvm_arch_vcpu_ioctl_run+0x141d/0x14e0 [kvm] [<ffffffffa071405d>] kvm_vcpu_ioctl+0x33d/0x620 [kvm] [<ffffffff81241648>] do_vfs_ioctl+0x298/0x480 [<ffffffff812418a9>] SyS_ioctl+0x79/0x90 [<ffffffff817a0f2e>] entry_SYSCALL_64_fastpath+0x12/0x71 Code: 55 83 ff 07 48 89 e5 77 27 89 ff ff 24 fd 90 87 80 81 0f 23 fe 5d c3 0f 23 c6 5d c3 0f 23 ce 5d c3 0f 23 d6 5d c3 0f 23 de 5d c3 <0f> 23 f6 5d c3 0f 0b 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 RIP [<ffffffff810639eb>] native_set_debugreg+0x2b/0x40 RSP <ffff88005836bd50> Testcase (beautified/reduced from syzkaller output): #include <unistd.h> #include <sys/syscall.h> #include <string.h> #include <stdint.h> #include <linux/kvm.h> #include <fcntl.h> #include <sys/ioctl.h> long r[8]; int main() { struct kvm_debugregs dr = { 0 }; r[2] = open("/dev/kvm", O_RDONLY); r[3] = ioctl(r[2], KVM_CREATE_VM, 0); r[4] = ioctl(r[3], KVM_CREATE_VCPU, 7); memcpy(&dr, "\x5d\x6a\x6b\xe8\x57\x3b\x4b\x7e\xcf\x0d\xa1\x72" "\xa3\x4a\x29\x0c\xfc\x6d\x44\x00\xa7\x52\xc7\xd8" "\x00\xdb\x89\x9d\x78\xb5\x54\x6b\x6b\x13\x1c\xe9" "\x5e\xd3\x0e\x40\x6f\xb4\x66\xf7\x5b\xe3\x36\xcb", 48); r[7] = ioctl(r[4], KVM_SET_DEBUGREGS, &dr); r[6] = ioctl(r[4], KVM_RUN, 0); } Reported-by:
-
Christoffer Dall authored
commit fa89c77e upstream. When saving the state of the list registers, it is critical to reset them zero, as we could otherwise leave unexpected EOI interrupts pending for virtual level interrupts. Signed-off-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
-
Christoffer Dall authored
commit 4d3afc9b upstream. When saving the state of the list registers, it is critical to reset them zero, as we could otherwise leave unexpected EOI interrupts pending for virtual level interrupts. Signed-off-by:
-
Jakub Sitnicki authored
[ Upstream commit 00bc0ef5 ] At present we perform an xfrm_lookup() for each UDPv6 message we send. The lookup involves querying the flow cache (flow_cache_lookup) and, in case of a cache miss, creating an XFRM bundle. If we miss the flow cache, we can end up creating a new bundle and deriving the path MTU (xfrm_init_pmtu) from on an already transformed dst_entry, which we pass from the socket cache (sk->sk_dst_cache) down to xfrm_lookup(). This can happen only if we're caching the dst_entry in the socket, that is when we're using a connected UDP socket. To put it another way, the path MTU shrinks each time we miss the flow cache, which later on leads to incorrectly fragmented payload. It can be observed with ESPv6 in transport mode: 1) Set up a transformation and lower the MTU to trigger fragmentation # ip xfrm policy add dir out src ::1 dst ::1 \ tmpl src ::1 dst ::1 proto esp spi 1 # ip xfrm state add src ::1 dst ::1 \ proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b # ip link set dev lo mtu 1500 2) Monitor the packet flow and set up an UDP sink # tcpdump -ni lo -ttt & # socat udp6-listen:12345,fork /dev/null & 3) Send a datagram that needs fragmentation with a connected socket # perl -e 'print "@" x 1470 | socat - udp6:[::1]:12345 2016/06/07 18:52:52 socat[724] E read(3, 0x555bb3d5ba00, 8192): Protocol error 00:00:00.000000 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x2), length 1448 00:00:00.000014 IP6 ::1 > ::1: frag (1448|32) 00:00:00.000050 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x3), length 1272 (^ ICMPv6 Parameter Problem) 00:00:00.000022 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x5), length 136 4) Compare it to a non-connected socket # perl -e 'print "@" x 1500' | socat - udp6-sendto:[::1]:12345 00:00:40.535488 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x6), length 1448 00:00:00.000010 IP6 ::1 > ::1: frag (1448|64) What happens in step (3) is: 1) when connecting the socket in __ip6_datagram_connect(), we perform an XFRM lookup, miss the flow cache, create an XFRM bundle, and cache the destination, 2) afterwards, when sending the datagram, we perform an XFRM lookup, again, miss the flow cache (due to mismatch of flowi6_iif and flowi6_oif, which is an issue of its own), and recreate an XFRM bundle based on the cached (and already transformed) destination. To prevent the recreation of an XFRM bundle, avoid an XFRM lookup altogether whenever we already have a destination entry cached in the socket. This prevents the path MTU shrinkage and brings us on par with UDPv4. The fix also benefits connected PINGv6 sockets, another user of ip6_sk_dst_lookup_flow(), who also suffer messages being transformed twice. Joint work with Hannes Frederic Sowa. Reported-by:
Jan Tluka <jtluka@redhat.com> Signed-off-by:
Jakub Sitnicki <jkbs@redhat.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Guillaume Nault authored
[ Upstream commit a5c5e2da ] Unused fields of udp_cfg must be all zeros. Otherwise setup_udp_tunnel_sock() fills ->gro_receive and ->gro_complete callbacks with garbage, eventually resulting in panic when used by udp_gro_receive(). [ 72.694123] BUG: unable to handle kernel paging request at ffff880033f87d78 [ 72.695518] IP: [<ffff880033f87d78>] 0xffff880033f87d78 [ 72.696530] PGD 26e2067 PUD 26e3067 PMD 342ed063 PTE 8000000033f87163 [ 72.696530] Oops: 0011 [#1] SMP KASAN [ 72.696530] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core ip6_udp_tunnel udp_tunnel pptp gre pppox ppp_generic slhc crc32c_intel ghash_clmulni_intel jitterentropy_rng sha256_generic hmac drbg ansi_cprng aesni_intel evdev aes_x86_64 ablk_helper cryptd lrw gf128mul glue_helper serio_raw acpi_cpufreq button proc\ essor ext4 crc16 jbd2 mbcache virtio_blk virtio_net virtio_pci virtio_ring virtio [ 72.696530] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.7.0-rc1 #1 [ 72.696530] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014 [ 72.696530] task: ffff880035b59700 ti: ffff880035b70000 task.ti: ffff880035b70000 [ 72.696530] RIP: 0010:[<ffff880033f87d78>] [<ffff880033f87d78>] 0xffff880033f87d78 [ 72.696530] RSP: 0018:ffff880035f87bc0 EFLAGS: 00010246 [ 72.696530] RAX: ffffed000698f996 RBX: ffff88003326b840 RCX: ffffffff814cc823 [ 72.696530] RDX: ffff88003326b840 RSI: ffff880033e48038 RDI: ffff880034c7c780 [ 72.696530] RBP: ffff880035f87c18 R08: 000000000000a506 R09: 0000000000000000 [ 72.696530] R10: ffff880035f87b38 R11: ffff880034b9344d R12: 00000000ebfea715 [ 72.696530] R13: 0000000000000000 R14: ffff880034c7c780 R15: 0000000000000000 [ 72.696530] FS: 0000000000000000(0000) GS:ffff880035f80000(0000) knlGS:0000000000000000 [ 72.696530] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 72.696530] CR2: ffff880033f87d78 CR3: 0000000033c98000 CR4: 00000000000406a0 [ 72.696530] Stack: [ 72.696530] ffffffff814cc834 ffff880034b93468 0000001481416818 ffff88003326b874 [ 72.696530] ffff880034c7ccb0 ffff880033e48038 ffff88003326b840 ffff880034b93462 [ 72.696530] ffff88003326b88a ffff88003326b88c ffff880034b93468 ffff880035f87c70 [ 72.696530] Call Trace: [ 72.696530] <IRQ> [ 72.696530] [<ffffffff814cc834>] ? udp_gro_receive+0x1c6/0x1f9 [ 72.696530] [<ffffffff814ccb1c>] udp4_gro_receive+0x2b5/0x310 [ 72.696530] [<ffffffff814d989b>] inet_gro_receive+0x4a3/0x4cd [ 72.696530] [<ffffffff81431b32>] dev_gro_receive+0x584/0x7a3 [ 72.696530] [<ffffffff810adf7a>] ? __lock_is_held+0x29/0x64 [ 72.696530] [<ffffffff814321f7>] napi_gro_receive+0x124/0x21d [ 72.696530] [<ffffffffa000b145>] virtnet_receive+0x8df/0x8f6 [virtio_net] [ 72.696530] [<ffffffffa000b27e>] virtnet_poll+0x1d/0x8d [virtio_net] [ 72.696530] [<ffffffff81431350>] net_rx_action+0x15b/0x3b9 [ 72.696530] [<ffffffff815893d6>] __do_softirq+0x216/0x546 [ 72.696530] [<ffffffff81062392>] irq_exit+0x49/0xb6 [ 72.696530] [<ffffffff81588e9a>] do_IRQ+0xe2/0xfa [ 72.696530] [<ffffffff81587a49>] common_interrupt+0x89/0x89 [ 72.696530] <EOI> [ 72.696530] [<ffffffff810b05df>] ? trace_hardirqs_on_caller+0x229/0x270 [ 72.696530] [<ffffffff8102b3c7>] ? default_idle+0x1c/0x2d [ 72.696530] [<ffffffff8102b3c5>] ? default_idle+0x1a/0x2d [ 72.696530] [<ffffffff8102bb8c>] arch_cpu_idle+0xa/0xc [ 72.696530] [<ffffffff810a6c39>] default_idle_call+0x1a/0x1c [ 72.696530] [<ffffffff810a6d96>] cpu_startup_entry+0x15b/0x20f [ 72.696530] [<ffffffff81039a81>] start_secondary+0x12c/0x133 [ 72.696530] Code: ff ff ff ff ff ff ff ff ff ff 7f ff ff ff ff ff ff ff 7f 00 7e f8 33 00 88 ff ff 6d 61 58 81 ff ff ff ff 5e de 0a 81 ff ff ff ff <00> 5c e2 34 00 88 ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 72.696530] RIP [<ffff880033f87d78>] 0xffff880033f87d78 [ 72.696530] RSP <ffff880035f87bc0> [ 72.696530] CR2: ffff880033f87d78 [ 72.696530] ---[ end trace ad7758b9a1dccf99 ]--- [ 72.696530] Kernel panic - not syncing: Fatal exception in interrupt [ 72.696530] Kernel Offset: disabled [ 72.696530] ---[ end Kernel panic - not syncing: Fatal exception in interrupt v2: use empty initialiser instead of "{ NULL }" to avoid relying on first field's type. Fixes: 38fd2af2 ("udp: Add socket based GRO and config") Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
-
Toshiaki Makita authored
[ Upstream commit 0b148def ] The missing br_vlan_should_use() test caused creation of an unneeded local fdb entry on changing mac address of a bridge device when there is a vlan which is configured on a bridge port but not on the bridge device. Fixes: 2594e906 ("bridge: vlan: add per-vlan struct and move to rhashtables") Signed-off-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Yuchung Cheng authored
[ Upstream commit ce3cf4ec ] The v6 tcp stats scan do not provide TLP and ER timer information correctly like the v4 version . This patch fixes that. Fixes: 6ba8a3b1 ("tcp: Tail loss probe (TLP)") Fixes: eed530b6 ("tcp: early retransmit") Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit 5b6c1b4d ] In bpf_perf_event_read() and bpf_perf_event_output(), we must use READ_ONCE() for fetching the struct file pointer, which could get updated concurrently, so we must prevent the compiler from potential refetching. We already do this with tail calls for fetching the related bpf_prog, but not so on stored perf events. Semantics for both are the same with regards to updates. Fixes: a43eec30 ("bpf: introduce bpf_perf_event_output() helper") Fixes: 35578d79 ("bpf: Implement function bpf_perf_event_read() that get the selected hardware PMU conuter") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Elad Kanfi authored
[ Upstream commit 86651650 ] Since NAPI works by shutting down event interrupts when theres work and turning them on when theres none, the net driver must make sure that interrupts are disabled when it reschedules polling. By calling napi_reschedule, the driver switches to polling mode, therefor there should be no interrupt interference. Any received packets will be handled in nps_enet_poll by polling the HW indication of received packet until all packets are handled. Signed-off-by:
Elad Kanfi <eladkan@mellanox.com> Acked-by:
Noam Camus <noamca@mellanox.com> Tested-by:
Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by:
-
Chen Haiquan authored
[ Upstream commit ce577668 ] When create a new vxlan link, example: ip link add vtap mtu 1440 type vxlan vni 1 dev eth0 The argument "mtu" has no effect, because it is not set to conf->mtu. The default value is used in vxlan_dev_configure function. This problem was introduced by commit 0dfbdf41 (vxlan: Factor out device configuration). Fixes: 0dfbdf41 (vxlan: Factor out device configuration) Signed-off-by:
Chen Haiquan <oc@yunify.com> Acked-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Marek Vasut authored
[ Upstream commit 643d60bf ] The memcpy() currently copies mdio_bus_data into new_bus->irq, which makes no sense, since the mdio_bus_data structure contains more than just irqs. The code was likely supposed to copy mdio_bus_data->irqs into the new_bus->irq instead, so fix this. Fixes: e7f4dc35 ("mdio: Move allocation of interrupts into core") Signed-off-by:
Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Feng Tang authored
[ Upstream commit 26c5f03b ] This patch follows Eric Dumazet's commit 7b701764 for Atheros atl1c driver to fix one exactly same bug in alx driver, that the network link will be lost in 1-5 minutes after the device is up. My laptop Lenovo Y580 with Atheros AR8161 ethernet device hit the same problem with kernel 4.4, and it will be cured by Jarod Wilson's commit c406700c for alx driver which get merged in 4.5. But there are still some alx devices can't function well even with Jarod's patch, while this patch could make them work fine. More details on https://bugzilla.kernel.org/show_bug.cgi?id=70761 The debug shows the issue is very likely to be related with the RX DMA address, specifically 0x...f80, if RX buffer get 0x...f80 several times, their will be RX overflow error and device will stop working. For kernel 4.5.0 with Jarod's patch which works fine with my AR8161/Lennov Y580, if I made some change to the __netdev_alloc_skb --> __alloc_page_frag() to make the allocated buffer can get an address with 0x...f80, then the same error happens. If I make it to 0x...f40 or 0x....fc0, everything will be still fine. So I tend to believe that the 0x..f80 address cause the silicon to behave abnormally. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70761 Cc: Eric Dumazet <edumazet@google.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Jarod Wilson <jarod@redhat.com> Signed-off-by:
Feng Tang <feng.tang@intel.com> Tested-by:
Ole Lukoie <olelukoie@mail.ru> Signed-off-by:
-
Ivan Vecera authored
[ Upstream commit f6988cb6 ] The team_device_event() notifier calls team_compute_features() to fix vlan_features under team->lock to protect team->port_list. The problem is that subsequent __team_compute_features() calls netdev_change_features() to propagate vlan_features to upper vlan devices while team->lock is still taken. This can lead to deadlock when NETIF_F_LRO is modified on lower devices or team device itself. Example: The team0 as active backup with eth0 and eth1 NICs. Both eth0 & eth1 are LRO capable and LRO is enabled. Thus LRO is also enabled on team0. The command 'ethtool -K team0 lro off' now hangs due to this deadlock: dev_ethtool() -> ethtool_set_features() -> __netdev_update_features(team) -> netdev_sync_lower_features() -> netdev_update_features(lower_1) -> __netdev_update_features(lower_1) -> netdev_features_change(lower_1) -> call_netdevice_notifiers(...) -> team_device_event(lower_1) -> team_compute_features(team) [TAKES team->lock] -> netdev_change_features(team) -> __netdev_update_features(team) -> netdev_sync_lower_features() -> netdev_update_features(lower_2) -> __netdev_update_features(lower_2) -> netdev_features_change(lower_2) -> call_netdevice_notifiers(...) -> team_device_event(lower_2) -> team_compute_features(team) [DEADLOCK] The bug is present in team from the beginning but it appeared after the commit fd867d51 (net/core: generic support for disabling netdev features down stack) that adds synchronization of features with lower devices. Fixes: fd867d51 (net/core: generic support for disabling netdev features down stack) Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
Ivan Vecera <ivecera@redhat.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Edward Cree authored
[ Upstream commit c0795bf6 ] Otherwise, if we fail to allocate new PIO buffers, our TXQs will try to use the old ones, which aren't there any more. Fixes: 183233be "sfc: Allocate and link PIO buffers; map them with write-combining" Signed-off-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
-
Gregory CLEMENT authored
[ Upstream commit b388fc74 ] When hwbm_pool_add exited in error the spinlock was not released. This patch fixes this issue. Fixes: 8cb2d8bf ("net: add a hardware buffer management helper API") Reported-by:
Jean-Jacques Hiblot <jjhiblot@traphandler.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Gregory CLEMENT authored
[ Upstream commit 91c45e38 ] The spinlock used by the hwbm functions must be initialized by the network driver. This commit fixes this lack and the following erros when lockdep is enabled: INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. [<c010ff80>] (unwind_backtrace) from [<c010bd08>] (show_stack+0x10/0x14) [<c010bd08>] (show_stack) from [<c032913c>] (dump_stack+0xb4/0xe0) [<c032913c>] (dump_stack) from [<c01670e4>] (__lock_acquire+0x1f58/0x2060) [<c01670e4>] (__lock_acquire) from [<c0167dec>] (lock_acquire+0xa4/0xd0) [<c0167dec>] (lock_acquire) from [<c06f6650>] (_raw_spin_lock_irqsave+0x54/0x68) [<c06f6650>] (_raw_spin_lock_irqsave) from [<c058e830>] (hwbm_pool_add+0x1c/0xdc) [<c058e830>] (hwbm_pool_add) from [<c043f4e8>] (mvneta_bm_pool_use+0x338/0x490) [<c043f4e8>] (mvneta_bm_pool_use) from [<c0443198>] (mvneta_probe+0x654/0x1284) [<c0443198>] (mvneta_probe) from [<c03b894c>] (platform_drv_probe+0x4c/0xb0) [<c03b894c>] (platform_drv_probe) from [<c03b7158>] (driver_probe_device+0x214/0x2c0) [<c03b7158>] (driver_probe_device) from [<c03b72c4>] (__driver_attach+0xc0/0xc4) [<c03b72c4>] (__driver_attach) from [<c03b5440>] (bus_for_each_dev+0x68/0x9c) [<c03b5440>] (bus_for_each_dev) from [<c03b65b8>] (bus_add_driver+0x1a0/0x218) [<c03b65b8>] (bus_add_driver) from [<c03b79cc>] (driver_register+0x78/0xf8) [<c03b79cc>] (driver_register) from [<c01018f4>] (do_one_initcall+0x90/0x1dc) [<c01018f4>] (do_one_initcall) from [<c0900de4>] (kernel_init_freeable+0x15c/0x1fc) [<c0900de4>] (kernel_init_freeable) from [<c06eed90>] (kernel_init+0x8/0x114) [<c06eed90>] (kernel_init) from [<c0107910>] (ret_from_fork+0x14/0x24) Fixes: baa11ebc ("net: mvneta: Use the new hwbm framework") Reported-by:
-
Daniel Borkmann authored
[ Upstream commit 612bacad ] Follow-up to commit e27f4a94 ("bpf: Use mount_nodev not mount_ns to mount the bpf filesystem"), which removes the FS_USERNS_MOUNT flag. The original idea was to have a per mountns instance instead of a single global fs instance, but that didn't work out and we had to switch to mount_nodev() model. The intent of that middle ground was that we avoid users who don't play nice to create endless instances of bpf fs which are difficult to control and discover from an admin point of view, but at the same time it would have allowed us to be more flexible with regard to namespaces. Therefore, since we now did the switch to mount_nodev() as a fix where individual instances are created, we also need to remove userns mount flag along with it to avoid running into mentioned situation. I don't expect any breakage at this early point in time with removing the flag and we can revisit this later should the requirement for this come up with future users. This and commit e27f4a94 have been split to facilitate tracking should any of them run into the unlikely case of causing a regression. Fixes: b2197755 ("bpf: add support for persistent maps/progs") Signed-off-by:
-
