Wait for the chip to be ready before any access to it. On the
Snowball platform we need to enable an external regulator before
the chip comes online, and then it happens that the device is
not yet ready at probe time, so let's wait for it.
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

multicast_lock is taken in softirq context, so we should use
spin_lock_bh() in userspace.

call-chain in softirq context:
run_timer_softirq()
	br_multicast_query_expired()

call-chain in userspace:
sysfs_write_file()
	store_multicast_snooping()
		br_multicast_toggle()
Signed-off-by: Andrew Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 1c5cae81 removed an explicit call to dev_alloc_name in ip6_tnl_create
because register_netdevice will now create a valid name.  This works for the
net_device itself.

However the tunnel keeps a copy of the name in the parms structure for the
ip6_tnl associated with the tunnel.  parms.name is set by copying the net_device
name in ip6_tnl_dev_init_gen.  That function is called from ip6_tnl_dev_init in
ip6_tnl_create, but it is done before register_netdevice is called so the name
is set to a bogus value in the parms.name structure.

This shows up if you do a simple tunnel add, followed by a tunnel show:

[root@localhost ~]# ip -6 tunnel add remote fec0::100 local fec0::200
[root@localhost ~]# ip -6 tunnel show
ip6tnl0: ipv6/ipv6 remote :: local :: encaplimit 0 hoplimit 0 tclass 0x00 flowlabel 0x00000 (flowinfo 0x00000000)
ip6tnl%d: ipv6/ipv6 remote fec0::100 local fec0::200 encaplimit 4 hoplimit 64 tclass 0x00 flowlabel 0x00000 (flowinfo 0x00000000)
[root@localhost ~]#

Fix this by moving the strcpy out of ip6_tnl_dev_init_gen, and calling it after
register_netdevice has successfully returned.

Cc: stable@vger.kernel.org
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change makes sure that tx_packets/rx_bytes ifconfig counters are
updated even on NICs that don't provide hardware support for these
stats: they are now updated in software. For the sake of consistency,
we also now have tx_bytes updated in software (hardware counters
include ethernet CRC, and software doesn't account for it).

This reverts parts of:
 - "forcedeth: statistics optimization" (21828163)
 - "forcedeth: Improve stats counters" (0bdfea8b)
 - "forcedeth: remove unneeded stats updates" (4687f3f3)

Tested:
  pktgen + loopback (http://patchwork.ozlabs.org/patch/124698/)
  reports identical tx_packets/rx_packets and tx_bytes/rx_bytes.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 1bc144b6 ("net, rds, Replace xlist in net/rds/xlist.h with
llist") added "select LLIST" to the RDS_RDMA Kconfig entry. But there is
no Kconfig symbol named LLIST. The select statement for that symbol is a
nop. Drop it.

lib/llist.o is builtin, so all that's needed to use the llist
functionality is to include linux/llist.h, which this commit also did.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

We test for 'tx_ring' being != zero and BUG() if that's the case. So after
that check there is no way that 'tx_ring' could be anything _but_ zero, so
testing it again is just dead code. Once that dead code is removed, the
'pkc' local variable becomes entirely redundant, so remove that as well.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the ahash driver returns -EBUSY, AH4/6 input functions return
NET_XMIT_DROP, presumably copied from the output code path.  But
returning transmit codes on input doesn't make a lot of sense.
Since NET_XMIT_DROP is a positive int, this gets interpreted as
the next header type (i.e., success).  As that can only end badly,
remove the check.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change them over to plain "ETHERNET"
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When opt->srr_is_hit is set skb_rtable(skb) has been updated for
'nexthop' and iph->daddr should always equals to skb_rtable->rt_dst
holds, We need update iph->daddr either.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The AH4/6 ahash input callbacks read out the nexthdr field from the AH
header *after* they overwrite that header.  This is obviously not going
to end well.  Fix it up.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The AH4/6 ahash output callbacks pass nexthdr to xfrm_output_resume
instead of the error code.  This appears to be a copy+paste error from
the input case, where nexthdr is expected.  This causes the driver to
continuously add AH headers to the datagram until either an allocation
fails and the packet is dropped or the ahash driver hits a synchronous
fallback and the resulting monstrosity is transmitted.

Correct this issue by simply passing the error code unadulterated.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit ff5a3b50 ("hippi: Move the HIPPI driver") moved the HIPPI
driver into drivers/net/hippi. It didn't source
drivers/net/hippi/Kconfig though, so it didn't make all necessary
Kconfig changes. So let drivers/net/kconfig source HIPPI's Kconfig file.

[ Fix syntax error at the end of HIPP's Kconfig file. -DaveM ]
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While tracing down a connectivity problem on the temac I connected a
probe to the Cross bar irq, and it was triggered when doing
ifdown->ifup.

This is fixed once waiting for the indirect write to end. Since it is
not on the hot path there is no performance loss.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not enable the irq until the scatter gather registers are ready to
handle the data. Otherwise an irq from a packet send/received before
last close can lead to an access to an invalid memory region on the irq
handler.

Also, stop the dma engine on close.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of ssh://ra.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

A minor fix for the check that verifies that all given SSIDs (in req) exist
in the filters (the match sets)
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This happens with devices using a regulatory domain 0x68 that are only
5Ghz capable because ath_reg_apply_active_scan_flags assumes that we
always have a 2,4Ghz band.

CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 82cd838c, ra == 82cd8384
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000061 00000003 00000024
$ 4 : 00000003 000016c1 82f900ac 00000024
$ 8 : 00000000 82cda304 0058bad8 00000005
$12 : 005908f8 001e8481 00000003 1dcd6500
$16 : 00000002 00000000 82c700c0 82c700c0
$20 : 82d415e4 82c70d64 82c70200 82c715bc
$24 : 00000000 11e1a300
$28 : 82ce2000 82ce3c70 82c715a8 82cd8384
Hi : 00000000
Lo : 0000001e
epc : 82cd838c ath_reg_apply_world_flags+0x78/0x17c [ath]
Not tainted
ra : 82cd8384 ath_reg_apply_world_flags+0x70/0x17c [ath]
Status: 1000d403 KERNEL EXL IE
Cause : 80800008
BadVA : 00000000
PrId : 00019374 (MIPS 24Kc)
Modules linked in: ath9k(+) ath9k_common ath9k_hw ath mac80211 cfg80211
	compat_firmware_class compat arc4 aes_generic deflate ecb cbc
	leds_gpio button_hotplug gpio_buttons input_polldev ie
Process insmod (pid: 464, threadinfo=82ce2000, task=838b31d8, tls=00000000)
Stack : 00000000 00000002 82f900ac 82c700c0 82d415e4 82c70d64 00000000 00000068
82f900ac 82cd88f4 82c700c0 82cda304 00000001 000020f0 82f90000 82c70d40
00000002 82f90000 82f900ac 82d4207c 82d518a0 00000002 7fee6118 8017c0d8
00000008 8397ba00 82c70d40 00000000 82c70200 83813000 83813058 b0010000
82d518a0 00000002 7fee6118 82d4b8c8 83445cc0 80120dc0 83804000 800eeda0
...
Call Trace:
[<82cd838c>] ath_reg_apply_world_flags+0x78/0x17c [ath]
[<82cd88f4>] ath_regd_init+0x464/0x488 [ath]
[<82d4207c>] ath9k_init_device+0x6a4/0x6b4 [ath9k]
[<82d4b8c8>] ath_pci_probe+0x27c/0x358 [ath9k]
[<80181de0>] pci_device_probe+0x64/0xa4
[<8019e874>] driver_probe_device+0xb8/0x190
[<8019e9b8>] __driver_attach+0x6c/0xa4
[<8019dfc0>] bus_for_each_dev+0x60/0xb0
[<8019d744>] bus_add_driver+0xc4/0x25c
[<8019ed6c>] driver_register+0xe0/0x198
[<8018206c>] __pci_register_driver+0x50/0xe0
[<82dd0010>] ath9k_init+0x10/0x54 [ath9k]
[<8006b4a0>] do_one_initcall+0x68/0x1ec
[<800a901c>] sys_init_module+0xec/0x23c
[<80062544>] stack_done+0x20/0x3c
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Two new struct members were not documented, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As we update the learned pmtu informations on demand, we might
report a nagative expiration time value to userspace if the
pmtu informations are already expired and we have not send a
packet to that inetpeer after expiration. With this patch we
send a expire time of null to userspace after expiration
until the next packet is send to that inetpeer.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Small fix in Documentation, since min_pmtu is 512 + 20 + 20 = 552
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP_NODELAY is weaker than TCP_CORK, when TCP_CORK was set, small
segments will always pass Nagle test regardless of TCP_NODELAY option.
Signed-off-by: Feng King <kinwin2008@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To prevent the SBus driver for Sun Happy Meal cards from being loaded for
PCI cards utilizing the same chipset, a filter was added to the probe
function in commit 0b492fce.

The filter was implemented by checking the name of the parent node in
the OF tree. This patch extends this filter, so that the driver will
load on SBus systems that are based upon SBI SBus Bridges.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pskb_may_pull() can change skb->data, so we have to load ptr/optr at the
right place.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver used NET_IP_ALIGN to remove some additional padding inside of
the rx_fixup function. On many architectures NET_IP_ALIGN defaults to 2
which removed the correct amount of bytes.

On MCORE2-machines commit ea812ca1
introduces a change which sets NET_IP_ALIGN to 0 by default. Which
triggered the bug on these machines.

This fix introduces a new RXW_PADDING define and uses this instead of
NET_IP_ALIGN. The name was taken from the original SMSC7500 driver which
is provided by SMSC.
Signed-off-by: Nico Erfurth <ne@erfurth.eu>
Tested-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 4291 Section 2.7 says Multicast addresses must not be used as source
addresses in IPv6 packets - drop them on input so we don't process the
packet further.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Reported-and-Tested-by: Kumar Sanghvi <divinekumar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The link down would occur when reseting PHY. And it would take about 2 ~ 5 seconds
from link down to link up. If the delay of pm_schedule_suspend is not long enough,
the device would enter runtime_suspend before link up. After link up, the device
would wake up and reset PHY again. Then, you would find the driver keep in a loop
of runtime_suspend and rumtime_resume.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since this device declares itself as vendor specific, must add
a new entry to device ID table to support it.

usb-device output of this device:

T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=413c ProdID=8197 Rev=01.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=D0DF9AA9C9F1
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

.. with new name.  Because nothing says "really solid kernel release"
like naming it after an extinct animal that just happened to be in the
news lately.

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (31 commits)
  ARM: OMAP: Fix export.h or module.h includes
  ARM: OMAP: omap_device: Include linux/export.h
  ARM: OMAP2: Fix H4 matrix keyboard warning
  ARM: OMAP1: Remove unused omap-alsa.h
  ARM: OMAP1: Fix warnings about enabling 32 KiHz timer
  ARM: OMAP2+: timer: Remove omap_device_pm_latency
  ARM: OMAP2+: clock data: Remove redundant timer clkdev
  ARM: OMAP: Devkit8000: Remove double omap_mux_init_gpio
  ARM: OMAP: usb: musb: OMAP: Delete unused function
  MAINTAINERS: Update linux-omap git repository
  ARM: OMAP: change get_context_loss_count ret value to int
  ARM: OMAP4: hsmmc: configure SDMMC1_DR0 properly
  ARM: OMAP4: hsmmc: Fix Pbias configuration on regulator OFF
  ARM: OMAP3: hwmod: fix variant registration and remove SmartReflex from common list
  ARM: OMAP: I2C: Fix omap_register_i2c_bus() return value on success
  ARM: OMAP: dmtimer: Include linux/module.h
  ARM: OMAP2+: l3-noc: Include linux/module.h
  ARM: OMAP2+: devices: Fixes for McPDM
  ARM: OMAP: Fix errors and warnings when building for one board
  ARM: OMAP3: PM: restrict erratum i443 handling to OMAP3430 only
  ...

Mountpoint crossing is similar to following procfs symlinks - we do
not get ->d_revalidate() called for dentry we have arrived at, with
unpleasant consequences for NFS4.

Simple way to reproduce the problem in mainline:

    cat >/tmp/a.c <<'EOF'
    #include <unistd.h>
    #include <fcntl.h>
    #include <stdio.h>
    main()
    {
            struct flock fl = {.l_type = F_RDLCK, .l_whence = SEEK_SET, .l_len = 1};
            if (fcntl(0, F_SETLK, &fl))
                    perror("setlk");
    }
    EOF
    cc /tmp/a.c -o /tmp/test

then on nfs4:

    mount --bind file1 file2
    /tmp/test < file1		# ok
    /tmp/test < file2		# spews "setlk: No locks available"...

What happens is the missing call of ->d_revalidate() after mountpoint
crossing and that's where NFS4 would issue OPEN request to server.

The fix is simple - treat mountpoint crossing the same way we deal with
following procfs-style symlinks.  I.e.  set LOOKUP_JUMPED...

Cc: stable@kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf top: Fix live annotation in the --stdio interface
  perf top tui: Don't recalc column widths considering just the first page
  perf report: Add progress bar when processing time ordered events
  perf hists browser: Warn about lost events
  perf tools: Fix a typo of command name as trace-cmd
  perf hists: Fix recalculation of total_period when sorting entries
  perf header: Fix build on old systems
  perf ui browser: Handle K_RESIZE in dialog windows
  perf ui browser: No need to switch char sets that often
  perf hists browser: Use K_TIMER
  perf ui: Rename ui__warning_paranoid to ui__error_paranoid
  perf ui: Reimplement the popup windows using libslang
  perf ui: Reimplement ui__popup_menu using ui__browser
  perf ui: Reimplement ui_helpline using libslang
  perf ui: Improve handling sigwinch a bit
  perf ui progress: Reimplement using slang
  perf evlist: Fix grouping of multiple events

Commit 32aaeffb (Merge branch
'modsplit-Oct31_2011'...) caused some build errors. Fix these
and make sure we always have export.h or module.h included
for MODULE_ and EXPORT_SYMBOL users:

$ grep -rl ^MODULE_ arch/arm/*omap*/*.c | xargs \
  grep -L linux/module.h
  arch/arm/mach-omap2/dsp.c
  arch/arm/mach-omap2/mailbox.c
  arch/arm/mach-omap2/omap-iommu.c
  arch/arm/mach-omap2/smartreflex.c

Also check we either have export.h or module.h included
for the files exporting symbols:

$ grep -rl EXPORT_SYMBOL arch/arm/*omap*/*.c | xargs \
  grep -L linux/export.h | xargs grep -L linux/module.h

Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Include linux/export.h to fix below build warning:

  CC      arch/arm/plat-omap/omap_device.o
arch/arm/plat-omap/omap_device.c:1055: warning: data definition has no type or storage class
arch/arm/plat-omap/omap_device.c:1055: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/arm/plat-omap/omap_device.c:1055: warning: parameter names (without types) in function declaration
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Timers set by __set_chan_timer() should use miliseconds instead of
jiffies. Commit 942ecc9c updated
l2cap_set_timer() so it expects timeout to be specified in msecs
instead of jiffies. This makes timeouts unreliable when CONFIG_HZ
is not set to 1000.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
  forcedeth: fix a few sparse warnings (variable shadowing)
  forcedeth: Improve stats counters
  forcedeth: remove unneeded stats updates
  forcedeth: Acknowledge only interrupts that are being processed
  forcedeth: fix race when unloading module
  MAINTAINERS/rds: update maintainer
  wanrouter: Remove kernel_lock annotations
  usbnet: fix oops in usbnet_start_xmit
  ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
  etherh: Add MAINTAINERS entry for etherh
  bonding: comparing a u8 with -1 is always false
  sky2: fix regression on Yukon Optima
  netlink: clarify attribute length check documentation
  netlink: validate NLA_MSECS length
  i825xx:xscale:8390:freescale: Fix Kconfig dependancies
  macvlan: receive multicast with local address
  tg3: Update version to 3.121
  tg3: Eliminate timer race with reset_task
  tg3: Schedule at most one tg3_reset_task run
  tg3: Obtain PCI function number from device
  ...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit 33060542.
The commit introduces regression when two 2.1 devices attempt
establish rfcomm channel. Such connection is refused since there's
a security block issue on l2cap. It means the link is unencrypted.

2011-09-16 18:08:46.567616 < ACL data: handle 1 flags 0x00 dlen 24
    0000: 14 00 40 00 06 00 02 00  0f 35 03 19 12 00 ff ff
..@......5....˙˙
    0010: 35 05 0a 00 00 ff ff 00                           5....˙˙.
2011-09-16 18:08:46.572377 > HCI Event: Number of Completed Packets
(0x13) plen 5
    handle 1 packets 1
2011-09-16 18:08:46.577931 > ACL data: handle 1 flags 0x02 dlen 88
    L2CAP(d): cid 0x0040 len 84 [psm 0]
      0000: 07 00 02 00 4f 00 4c 35  4a 35 48 09 00 00 0a 00
....O.L5J5H.....
      0010: 01 00 00 09 00 01 35 03  19 12 00 09 00 05 35 03
......5.......5.
      0020: 19 10 02 09 00 09 35 08  35 06 19 12 00 09 01 02
......5.5.......
      0030: 09 02 00 09 01 02 09 02  01 09 00 0a 09 02 02 09
................
      0040: 00 00 09 02 03 09 00 00  09 02 04 28 01 09 02 05
...........(....
      0050: 09 00 02 00                                       ....
2011-09-16 18:08:46.626057 < HCI Command: Authentication Requested
(0x01|0x0011) plen 2
    handle 1
2011-09-16 18:08:46.627614 > HCI Event: Command Status (0x0f) plen 4
    Authentication Requested (0x01|0x0011) status 0x00 ncmd 1
2011-09-16 18:08:46.627675 > HCI Event: Link Key Request (0x17) plen 6
    bdaddr 00:00:F2:6A:29:69
2011-09-16 18:08:46.634999 < HCI Command: Link Key Request Reply
(0x01|0x000b) plen 22
    bdaddr 00:00:F2:6A:29:69 key 58CD393179FC902E5E8F512A855EE532
2011-09-16 18:08:46.683278 > HCI Event: Command Complete (0x0e) plen 10
    Link Key Request Reply (0x01|0x000b) ncmd 1
    status 0x00 bdaddr 00:00:F2:6A:29:69
2011-09-16 18:08:46.764729 > HCI Event: Auth Complete (0x06) plen 3
    status 0x00 handle 1
2011-09-16 18:08:46.764821 < ACL data: handle 1 flags 0x00 dlen 12
    0000: 08 00 01 00 02 05 04 00  03 00 41 00              ..........A.
2011-09-16 18:08:46.764851 > HCI Event: Command Status (0x0f) plen 4
    Unknown (0x00|0x0000) status 0x00 ncmd 2
2011-09-16 18:08:46.768117 > HCI Event: Number of Completed Packets
(0x13) plen 5
    handle 1 packets 1
2011-09-16 18:08:46.770894 > ACL data: handle 1 flags 0x02 dlen 16
    L2CAP(s): Connect rsp: dcid 0x0000 scid 0x0041 result 3 status 0
      Connection refused - security block
2011-09-16 18:08:49.000691 < ACL data: handle 1 flags 0x00 dlen 12
    0000: 08 00 01 00 06 06 04 00  40 00 40 00              ........@.@.
2011-09-16 18:08:49.015675 > HCI Event: Number of Completed Packets
(0x13) plen 5
    handle 1 packets 1
2011-09-16 18:08:49.016927 > ACL data: handle 1 flags 0x02 dlen 12
    L2CAP(s): Disconn rsp: dcid 0x0040 scid 0x0040
2011-09-16 18:08:51.009480 < HCI Command: Disconnect (0x01|0x0006) plen
3
    handle 1 reason 0x13
    Reason: Remote User Terminated Connection
2011-09-16 18:08:51.011525 > HCI Event: Command Status (0x0f) plen 4
    Disconnect (0x01|0x0006) status 0x00 ncmd 1
2011-09-16 18:08:51.123494 > HCI Event: Disconn Complete (0x05) plen 4
    status 0x00 handle 1 reason 0x16
    Reason: Connection Terminated by Local Host
Signed-off-by: Arek Lichwa <arkadiusz.lichwa@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>