This patch adds support for Atom C2000 series (Avoton and Rangeley). And has
the following options:
  - New addresses register.
  - Caching output levels (see Intel external design spec, table 48-29)
  - No hardware blink.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch allows GPIO driver to cache GPIO_LVL output registers. The aim is to
support chipsets on which GPIO_LVL value can't be read for output pins.

Caching output levels implies the first output values reading as 0. The driver
so can't be aware of set values GPIOs by bootloader or BIOS.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch introduces regs and reglen pointers which allow a chipset to have
register addresses differing from ICH ones.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch allows gpio_ich driver to be aware of non blink capable chipsets.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

All those IDs are arbitrary and so can be encapsulated into an enumeration.
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add the correct silicon variant code ID (0x5) to the driver. This
new code is the 'production' variant code ID for DA9063.

This patch will remove the older variant code ID which matches the
pre-production silicon ID (0x3) for the DA9063 chip.

There is also some small amount of correction done in this patch:
it splits the revision code and correctly names it according to
the hardware specification and moves the dev_info() call before
the variant ID test.
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Return directly to avoid redundant lines of code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Realtek USB card reader provides a channel to transfer command or data to flash
memory cards. This driver exports host instances for mmc and memstick subsystems
and handles basic works.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

devm_regmap_init_i2c can fail. Check for it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

stw481x_regmap_config is local to this file.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add this header explicitly for IS_ERR and friends.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

'site' variable should be initialized with 0 so that when 'site'
property doesn't exist in DTB it can be handled correctly.

'0' value means board site number is motherboard (see
Documentation/devicetree/bindings/arm/vexpress.txt for details).
Signed-off-by: Semen Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

During probe the driver allocates two dummy I2C devices for subchips in
function pm800_pages_init(). Additionally this function allocates
regmaps for these subchips. If any of these steps fail then these dummy
I2C devices are not freed and resources leak.

On pm800_pages_init() fail the driver must call pm800_pages_exit() to
unregister dummy I2C devices.

Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

s/to support for/to add support for/
Signed-off-by: Laszlo Papp <lpapp@kde.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Three of the PMIC registers have some bits that are changed
autonomously by the PMIC itself (some time) after being set
by some component driver of the DA9052 PMIC and hence they
need to be marked as volatile so that the regmap API will
not cache their values.
Acked-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

During probe the driver allocates dummy I2C devices for MUIC and haptic
with i2c_new_dummy() but it does not check the return value of this
calls.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by devm_regmap_init_i2c() and i2c_unregister_device().

If i2c_new_dummy() fails for MUIC or haptic devices, fail also the probe
for main MFD driver.

Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

During probe the driver allocates dummy I2C device for companion chip
with i2c_new_dummy() but it does not check the return value of this call.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by regmap_init_i2c().

If i2c_new_dummy() fails for companion device, fail also the probe for
main MFD driver.

Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

During probe the driver allocates dummy I2C device for companion chip
and then allocates a regmap for it. If regmap_init_i2c() fails then the
I2C driver (allocated with i2c_new_dummy()) is not freed and this
resource leaks.

Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

During probe the driver allocates dummy I2C devices for RTC and ADC
with i2c_new_dummy() but it does not check the return value of this
calls.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().

If i2c_new_dummy() fails for RTC or ADC devices, fail also the probe
for main MFD driver.

Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

During probe the driver allocates dummy I2C device for RTC with i2c_new_dummy() but it does not check the return value of this call.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().

If i2c_new_dummy() fails for RTC device, fail also the probe for
main MFD driver.

Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

During probe the driver allocates dummy I2C device for RTC with
i2c_new_dummy() but it does not check the return value of this call.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().

If i2c_new_dummy() fails for RTC device, fail also the probe for main
MFD driver.

Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

During probe the driver allocates dummy I2C devices for RTC, haptic and
MUIC with i2c_new_dummy() but it does not check the return value of this
calls.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().

If i2c_new_dummy() fails for RTC, haptic or MUIC devices, fail also the
probe for main MFD driver.

Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Semicolon is not necessary after the while statement.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The TPS65218 chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:

 - Regulators.
 - Over Temperature warning and Shut down.

This patch adds support for tps65218 mfd device. At this time only
the regulator functionality is made available.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This changes the following mechanisms in the TC3589x device tree
probing path:

- Use the .of_match_table in struct device_driver to match the
  device in the device tree.
- Add matches for the proper compatible strings "toshiba,..."
  and all sub-variants, just as is done for the .id matches.
- Move over all the allocation of platform data etc to the
  tc3589x_of_probe() function and follow the pattern of passing
  a platform data pointer back, or an error pointer on error,
  as found in the STMPE driver.
- Match the new (proper) compatible strings for the GPIO and
  keypad MFD cells.
- Use of_device_is_compatible() rather than just !strcmp()
  to discover which cells to instantiate.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Expose some DSP registers which are useful for DSP users to be able to
access whilst debugging their firmware.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Expose some DSP registers which are useful for DSP users to be able to
access whilst debugging their firmware.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add of_compatible ("maxim,max14577-muic") to the mfd_cell for extcon
driver. If entry with such compatible is present in the DTS, the extcon
driver will have of_node set.

This may be useful for extcon consumers and it is documented in
bindings documentation.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Remove not needed max14577-private.h header inclusion in the main driver
header. Remove obvious comment.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Remove unused symbol: enum max14577_irq_source.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

It is currently not possible to select the SA1100 or Vexpress
drivers in the MFD subsystem, because the menu for the entire
subsystem ends before these options are presented.

Move the main menu closing and the endif for HAS_IOMEM to the
end of the file so these are selectable again.

Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Update the register patch based on latest evaluation of the device.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Added initial binding documentation for S2MPA01 MFD.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for S2MPA01 voltage and current regulator.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>