- 14 Feb, 2019 33 commits
-
-
Vadim Pasternak authored
Add low frequency bus capability in order to allow core functionality separation based on bus type. Driver could run over PCIe, which is considered as high frequency bus or I2C, which is considered as low frequency bus. In the last case time setting, for example, for thermal polling interval, should be increased. Use different thermal monitoring based on bus type. For I2C bus time is set to 20 seconds, while for PCIe 1 second polling interval is used. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vadim Pasternak authored
Add new API to read QSFP module's temperature thresholds - warning and critical. New internal API reads the temperature thresholds from the modules, which are equipped with the thermal sensor. These thresholds will be exposed via hwmon subsystem. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vadim Pasternak authored
Add FORE (Fan Out of Range Event Register), which is used for fan fault reading. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vadim Pasternak authored
Add MTBR (Management Temperature Bulk Register), which is used for port temperature reading in a bulk mode. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vadim Pasternak authored
Move QSFP EEPROM definitions to common location from the spectrum driver in order to make them available for other mlxsw modules. They are common for all kind of chips and have relation to SFF specifications 8024, 8436, 8472, 8636, rather than to chip type. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.open-mesh.org/linux-mergeDavid S. Miller authored
Simon Wunderlich says: ==================== This feature/cleanup patchset includes the following patches: - fix memory leak in in batadv_dat_put_dhcp, by Martin Weinelt - fix typo, by Sven Eckelmann - netlink restructuring patch series (part 2), by Sven Eckelmann (19 patches) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dan Carpenter authored
We need to set the error message on this path otherwise some of the callers, such as test_hints_case(), print from an uninitialized pointer. We had a similar bug earlier and set "errmsg" to NULL in the caller, test_delta_action_item(). That code is no longer required so I have removed it. Fixes: 9069a381 ("lib: objagg: implement optimization hints assembly and use hints for object creation") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dan Carpenter authored
There is a typo here. We intended to check "objagg2" but we instead test "objagg" which is not an error pointer. Fixes: 9069a381 ("lib: objagg: implement optimization hints assembly and use hints for object creation") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dan Carpenter authored
We need to set the error code on this path otherwise we return ERR_PTR(0) which would result in a NULL dereference in the caller. Fixes: 9069a381 ("lib: objagg: implement optimization hints assembly and use hints for object creation") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vishal Kulkarni authored
CR4_QSFP 10G Speed technology should be 10000baseKR_Full And also report available FEC modes. Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Jesper Dangaard Brouer says: ==================== Fix page_pool API and dma address storage As pointed out by David Miller in [1] the current page_pool implementation stores dma_addr_t in page->private. This won't work on 32-bit platforms with 64-bit DMA addresses since the page->private is an unsigned long and the dma_addr_t a u64. Since no driver is yet using the DMA mapping capabilities of the API let's fix this by storing the information in 'struct page' and use that to store and retrieve DMA addresses from network drivers. As long as the addresses returned from dma_map_page() are aligned the first bit, used by the compound pages code should not be set. Ilias tested the first two patches on Espressobin driver mvneta, for which we have patches for using the DMA API of page_pool. [1]: https://lore.kernel.org/netdev/20181207.230655.1261252486319967024.davem@davemloft.net/ ==================== Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jesper Dangaard Brouer authored
As pointed out by Alexander Duyck, the DMA mapping done in page_pool needs to use the DMA attribute DMA_ATTR_SKIP_CPU_SYNC. As the principle behind page_pool keeping the pages mapped is that the driver takes over the DMA-sync steps. Reported-by: Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ilias Apalodimas authored
As pointed out by David Miller the current page_pool implementation stores dma_addr_t in page->private. This won't work on 32-bit platforms with 64-bit DMA addresses since the page->private is an unsigned long and the dma_addr_t a u64. A previous patch is adding dma_addr_t on struct page to accommodate this. This patch adapts the page_pool related functions to use the newly added struct for storing and retrieving DMA addresses from network drivers. Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jesper Dangaard Brouer authored
The page_pool API is using page->private to store DMA addresses. As pointed out by David Miller we can't use that on 32-bit architectures with 64-bit DMA This patch adds a new dma_addr_t struct to allow storing DMA addresses Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Acked-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
YueHaibing authored
Remove duplicated include. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
John Hurley authored
With the introduction of flow_stats_update(), drivers now update the stats fields of the passed tc_cls_flower_offload struct, rather than call tcf_exts_stats_update() directly to update the stats of offloaded TC flower rules. However, if multiple qdiscs are registered to a TC shared block and a flower rule is applied, then, when getting stats for the rule, multiple callbacks may be made. Take this into consideration by modifying flow_stats_update to gather the stats from all callbacks. Currently, the values in tc_cls_flower_offload only account for the last stats callback in the list. Fixes: 3b1903ef ("flow_offload: add statistics retrieval infrastructure and use it") Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vlad Buslov authored
Recently introduced tc_setup_flow_action() can fail when parsing tcf_exts on some unsupported action commands. However, this should not affect the case when user did not explicitly request hw offload by setting skip_sw flag. Modify tc_setup_flow_action() callers to only propagate the error if skip_sw flag is set for filter that is being offloaded, and set extack error message in that case. Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Fixes: 3a7b6861 ("cls_api: add translator to flow_action representation") Signed-off-by: David S. Miller <davem@davemloft.net>
-
Colin Ian King authored
There are some statements that are indented incorrectly. Fix these. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Colin Ian King authored
There are some statements in an if-block that are not correctly indented. Fix these. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yang Wei authored
dev_consume_skb_irq() should be called in eth_txdone_irq() when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yang Wei authored
dev_consume_skb_irq() should be called in at91ether_interrupt() when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yang Wei authored
dev_consume_skb_irq() should be called when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yang Wei authored
dev_consume_skb_irq() should be called in intr_handler() when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yang Wei authored
dev_consume_skb_irq() should be called in moxart_tx_finished() when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yang Wei authored
dev_consume_skb_irq() should be called in mace_interrupt() when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yang Wei authored
dev_consume_skb_irq() should be called when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yang Wei authored
dev_consume_skb_irq() should be called in emac_mac_tx_process() when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yang Wei authored
dev_consume_skb_irq() should be called when skb xmit done. It makes drop profiles(dropwatch, perf) more friendly. Signed-off-by: Yang Wei <yang.wei9@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Maxime Chevallier says: ==================== net: phy: Add 2.5G/5GBASET PHYs support The 802.3bz standard defines 2 modes based on the NBASET alliance work that allow to use 2.5Gbps and 5Gbps speeds on Cat 5e, 6 and 7 cables. This series adds the necessary infrastructure to handle these modes with C45 PHYs. This series was originally part of a bigger one, that has seen 2 iterations [1] [2] that added support for these modes on Marvell Alaska PHYs. Following some discussions with Heiner and Andrew [3], we decided to split-out the generic parts so that we can work together on the following steps to get these mode fully working with Aquantia and Marvell PHYS. The first 3 patches are reworking some of the internal network phy infrastructure to handle the new modes in a more generic way. The 4th patch adds all the C45 register definition and accesses that follows the 802.3bz standard to support 2.5GBASET and 5GBASET. [1] : https://lore.kernel.org/netdev/20190118152352.26417-1-maxime.chevallier@bootlin.com/ [2] : https://lore.kernel.org/netdev/20190207094939.27369-1-maxime.chevallier@bootlin.com/ [3] : https://lore.kernel.org/netdev/81c340ea-54b0-1abf-94af-b8dc4ee83e3a@gmail.com/ ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Maxime Chevallier authored
The 802.3bz specification, based on previous by the NBASET alliance, defines the 2.5GBaseT and 5GBaseT link modes for ethernet traffic on cat5e, cat6 and cat7 cables. These mode integrate with the already defined C45 MDIO PMA/PMD registers set that added 10G support, by defining some previously reserved bits, and adding a new register (2.5G/5G Extended abilities). This commit adds the required definitions in include/uapi/linux/mdio.h to support these modes, and detect when a link-partner advertises them. It also adds support for these mode in the generic C45 PHY infrastructure. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Maxime Chevallier authored
Marvell 10G PHY driver has a generic way of initializing the supported link modes by reading the PHY's C45 PMA abilities. This can be made generic, since these registers are part of the 802.3 specifications. This commit extracts the config_init link_mode initialization code from marvell10g and uses it to introduce the genphy_c45_pma_read_abilities function. Only PMA modes are read, it's still up to the caller to set the Pause parameters. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Maxime Chevallier authored
Since of_set_phy_supported was moved to phy-core.c, we can also move of_set_phy_eee_broken to the same location, so that we have all OF functions in the same place. This patch doesn't intend to introduce any change in behaviour. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Maxime Chevallier authored
When setting a PHY's max speed using either the max-speed DT property or ethtool, we should mask-out all non-compatible modes according to the settings table, instead of just the 10/100BASET modes. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Suggested-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 13 Feb, 2019 3 commits
-
-
David S. Miller authored
Florian Fainelli says: ==================== Remove unused variables This removes unused variables from mlxsw and ethsw after the recent removal of SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS, build scripts are now fixed to take care of those warnings :). ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
After 1b8b589d ("staging: fsl-dpaa2: ethsw: Remove getting PORT_BRIDGE_FLAGS") we are not accessing any driver private data anymore, remove port_priv which is unused. Fixes: 1b8b589d ("staging: fsl-dpaa2: ethsw: Remove getting PORT_BRIDGE_FLAGS") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
After 1ecb1957 ("mlxsw: spectrum_switchdev: Remove getting PORT_BRIDGE_FLAGS") we are not accessing any driver private data structure, so the mlxsw_sp_port and mlxsw_sp variables are unused. Fixes: 1ecb1957 ("mlxsw: spectrum_switchdev: Remove getting PORT_BRIDGE_FLAGS") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 12 Feb, 2019 4 commits
-
-
Florian Fainelli authored
After 610d2b60 ("rocker: Remove getting PORT_BRIDGE_FLAGS") we no longer have a port_attr_bridge_flags_get member in the rocker_world_ops structre, fix that. Fixes: 610d2b60 ("rocker: Remove getting PORT_BRIDGE_FLAGS") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Vlad Buslov says: ==================== Refactor classifier API to work with chain/classifiers without rtnl lock Currently, all netlink protocol handlers for updating rules, actions and qdiscs are protected with single global rtnl lock which removes any possibility for parallelism. This patch set is a third step to remove rtnl lock dependency from TC rules update path. Recently, new rtnl registration flag RTNL_FLAG_DOIT_UNLOCKED was added. Handlers registered with this flag are called without RTNL taken. End goal is to have rule update handlers(RTM_NEWTFILTER, RTM_DELTFILTER, etc.) to be registered with UNLOCKED flag to allow parallel execution. However, there is no intention to completely remove or split rtnl lock itself. This patch set addresses specific problems in implementation of classifiers API that prevent its control path from being executed concurrently, and completes refactoring of cls API rules update handlers by removing rtnl lock dependency from code that handles chains and classifiers. Rules update handlers are registered with RTNL_FLAG_DOIT_UNLOCKED flag. This patch set substitutes global rtnl lock dependency on rules update path in cls API by extending its data structures with following locks: - tcf_block with 'lock' mutex. It is used to protect block state and life-time management fields of chains on the block (chain->refcnt, chain->action_refcnt, chain->explicitly crated, etc.). - tcf_chain with 'filter_chain_lock' mutex, that is used to protect list of classifier instances attached to chain. chain0->filter_chain_lock serializes calls to head change callbacks and allows them to rely on filter_chain_lock for serialization instead of rtnl lock. - tcf_proto with 'lock' spinlock that is intended to be used to synchronize access to classifiers that support unlocked execution. Classifiers are extended with reference counting to accommodate parallel access by unlocked cls API. Classifier ops structure is extended with additional 'put' function to allow reference counting of filters and intended to be used by classifiers that implement rtnl-unlocked API. Users of classifiers and individual filter instances are modified to always hold reference while working with them. Classifiers that support unlocked execution still need to know the status of rtnl lock, so their API is extended with additional 'rtnl_held' argument that is used to indicate that caller holds rtnl lock. Cls API propagates rtnl lock status across its helper functions and passes it to classifier. Changes from V3 to V4: - Patch 1: - Extract code that manages chain 'explicitly_created' flag into standalone patch. - Patch 2 - new. Changes from V2 to V3: - Change block->lock and chain->filter_chain_lock type to mutex. This removes the need for async miniqp refactoring and allows calling sleeping functions while holding the block->lock and chain->filter_chain_lock locks. - Previous patch 1 - async miniqp is no longer needed, remove the patch. - Patch 1: - Change block->lock type to mutex. - Implement tcf_block_destroy() helper function that destroys block->lock mutex before deallocating the block. - Revert GFP_KERNEL->GFP_ATOMIC memory allocation flags of tcf_chain which is no longer needed after block->lock type change. - Patch 6: - Change chain->filter_chain_lock type to mutex. - Assume chain0->filter_chain_lock synchronizations instead of rtnl lock in mini_qdisc_pair_swap() function that is called from head change callback of ingress Qdisc. With filter_chain_lock type changed to mutex it is now possible to call sleeping function while holding it, so it is now used instead of async implementation from previous versions of this patch set. - Patch 7: - Add local tp_next var to tcf_chain_flush() and use it to store tp->next pointer dereferenced with rcu_dereference_protected() to satisfy kbuild test robot. - Reset tp pointer to NULL at the beginning of tc_new_tfilter() to prevent its uninitialized usage in error handling code. This code was already implemented in patch 10, but must be in patch 8 to preserve code bisectability. - Put parent chain in tcf_proto_destroy(). In previous version this code was implemented in patch 1 which was removed in V3. Changes from V1 to V2: - Patch 1: - Use smp_store_release() instead of xchg() for setting miniqp->tp_head. - Move Qdisc deallocation to tc_proto_wq ordered workqueue that is used to destroy tcf proto instances. This is necessary to ensure that Qdisc is destroyed after all instances of chain/proto that it contains in order to prevent use-after-free error in tc_chain_notify_delete(). - Cache parent net device ifindex in block to prevent use-after-free of dev queue in tc_chain_notify_delete(). - Patch 2: - Use lockdep_assert_held() instead of spin_is_locked() for assertion. - Use 'free_block' argument in tcf_chain_destroy() instead of checking block's reference count and chain_list for second time. - Patch 7: - Refactor tcf_chain0_head_change_cb_add() to not take block->lock and chain0->filter_chain_lock in correct order. - Patch 10: - Always set 'tp_created' flag when creating tp to prevent releasing the chain twice when tp with same priority was inserted concurrently. - Patch 11: - Add additional check to prevent creation of new proto instance when parent chain is being flushed to reduce CPU usage. - Don't call tcf_chain_delete_empty() if tp insertion failed. - Patch 16 - new. - Patch 17: - Refactor to only lock take rtnl lock once (at the beginning of rule update handlers). - Always release rtnl mutex in the same function that locked it. Remove unlock code from tcf_block_release(). ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vlad Buslov authored
Register netlink protocol handlers for message types RTM_NEWTFILTER, RTM_DELTFILTER, RTM_GETTFILTER as unlocked. Set rtnl_held variable that tracks rtnl mutex state to be false by default. Introduce tcf_proto_is_unlocked() helper that is used to check tcf_proto_ops->flag to determine if ops can be called without taking rtnl lock. Manually lookup Qdisc, class and block in rule update handlers. Verify that both Qdisc ops and proto ops are unlocked before using any of their callbacks, and obtain rtnl lock otherwise. Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vlad Buslov authored
Refactor tcf_block_find() code into three standalone functions: - __tcf_qdisc_find() to lookup Qdisc and increment its reference counter. - __tcf_qdisc_cl_find() to lookup class. - __tcf_block_find() to lookup block and increment its reference counter. This change is necessary to allow netlink tc rule update handlers to call these functions directly in order to conditionally take rtnl lock according to Qdisc class ops flags before calling any of class ops functions. Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-