- 02 Apr, 2020 4 commits
-
-
Thommy Jakobsson authored
[ Upstream commit 5dd83049 ] In the public interface for chipselect, there is always an entry commented as "Dummy generic FIFO entry" pushed down to the fifo right after the activate/deactivate command. The dummy entry is 0x0, irregardless if the intention was to activate or deactive the cs. This causes the cs line to glitch rather than beeing activated in the case when there was an activate command. This has been observed on oscilloscope, and have caused problems for at least one specific flash device type connected to the qspi port. After the change the glitch is gone and cs goes active when intended. The reason why this worked before (except for the glitch) was because when sending the actual data, the CS bits are once again set. Since most flashes uses mode 0, there is always a half clk period anyway for cs to clk active setup time. If someone would rely on timing from a chip_select call to a transfer_one, it would fail though. It is unknown why the dummy entry was there in the first place, git log seems to be of no help in this case. The reference manual gives no indication of the necessity of this. In fact the lower 8 bits are a setup (or hold in case of deactivate) time expressed in cycles. So this should not be needed to fulfill any setup/hold timings. Signed-off-by:
Thommy Jakobsson <thommyj@gmail.com> Reviewed-by:
Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com> Link: https://lore.kernel.org/r/20200224162643.29102-1-thommyj@gmail.comSigned-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Kishon Vijay Abraham I authored
[ Upstream commit 27f13774 ] 'dma-ranges' in a PCI bridge node does correctly set dma masks for PCI devices not described in the DT. Certain DRA7 platforms (e.g., DRA76) has RAM above 32-bit boundary (accessible with LPAE config) though the PCIe bridge will be able to access only 32-bits. Add 'dma-ranges' property in PCIe RC DT nodes to indicate the host bridge can access only 32 bits. Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Naveen N. Rao authored
[ Upstream commit cb0cc635 ] Selecting CONFIG_DEBUG_INFO_BTF results in the below warning from ld: ld: warning: orphan section `.BTF' from `.btf.vmlinux.bin.o' being placed in section `.BTF' Include .BTF section in vmlinux explicitly to fix the same. Signed-off-by:
Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200220113132.857132-1-naveen.n.rao@linux.vnet.ibm.comSigned-off-by:
-
Yuji Sasaki authored
[ Upstream commit 136b5cd2 ] spi_qup_suspend() will cause synchronous external abort when runtime suspend is enabled and applied, as it tries to access SPI controller register while clock is already disabled in spi_qup_pm_suspend_runtime(). Signed-off-by:
Yuji sasaki <sasakiy@chromium.org> Signed-off-by:
Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20200214074340.2286170-1-vkoul@kernel.orgSigned-off-by:
-
- 20 Mar, 2020 36 commits
-
-
Greg Kroah-Hartman authored
-
Matteo Croce authored
commit 3e72dfdf upstream. Similarly to commit c543cb4a ("ipv4: ensure rcu_read_lock() in ipv4_link_failure()"), __ip_options_compile() must be called under rcu protection. Fixes: 3da1ed7a ("net: avoid use IPCB in cipso_v4_error") Suggested-by:
Guillaume Nault <gnault@redhat.com> Signed-off-by:
Matteo Croce <mcroce@redhat.com> Acked-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jann Horn authored
commit fd4d9c7d upstream. When kmem_cache_alloc_bulk() attempts to allocate N objects from a percpu freelist of length M, and N > M > 0, it will first remove the M elements from the percpu freelist, then call ___slab_alloc() to allocate the next element and repopulate the percpu freelist. ___slab_alloc() can re-enable IRQs via allocate_slab(), so the TID must be bumped before ___slab_alloc() to properly commit the freelist head change. Fix it by unconditionally bumping c->tid when entering the slowpath. Cc: stable@vger.kernel.org Fixes: ebe909e0 ("slub: improve bulk alloc strategy") Signed-off-by:
Jann Horn <jannh@google.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Kees Cook authored
commit f87b1c49 upstream. When the uaccess .fixup section was renamed to .text.fixup, one case was missed. Under ld.bfd, the orphaned section was moved close to .text (since they share the "ax" bits), so things would work normally on uaccess faults. Under ld.lld, the orphaned section was placed outside the .text section, making it unreachable. Link: https://github.com/ClangBuiltLinux/linux/issues/282 Link: https://bugs.chromium.org/p/chromium/issues/detail?id=1020633#c44 Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.1912032147340.17114@knanqh.ubzr Link: https://lore.kernel.org/lkml/202002071754.F5F073F1D@keescook/ Fixes: c4a84ae3 ("ARM: 8322/1: keep .text and .fixup regions closer together") Cc: stable@vger.kernel.org Signed-off-by:
Kees Cook <keescook@chromium.org> Reviewed-by:
Ard Biesheuvel <ardb@kernel.org> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Florian Fainelli authored
commit 45939ce2 upstream. It is possible for a system with an ARMv8 timer to run a 32-bit kernel. When this happens we will unconditionally have the vDSO code remove the __vdso_gettimeofday and __vdso_clock_gettime symbols because cntvct_functional() returns false since it does not match that compatibility string. Fixes: ecf99a43 ("ARM: 8331/1: VDSO initialization, mapping, and synchronization") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Qian Cai authored
[ Upstream commit 6c5d9112 ] journal_head::b_transaction and journal_head::b_next_transaction could be accessed concurrently as noticed by KCSAN, LTP: starting fsync04 /dev/zero: Can't open blockdev EXT4-fs (loop0): mounting ext3 file system using the ext4 subsystem EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null) ================================================================== BUG: KCSAN: data-race in __jbd2_journal_refile_buffer [jbd2] / jbd2_write_access_granted [jbd2] write to 0xffff99f9b1bd0e30 of 8 bytes by task 25721 on cpu 70: __jbd2_journal_refile_buffer+0xdd/0x210 [jbd2] __jbd2_journal_refile_buffer at fs/jbd2/transaction.c:2569 jbd2_journal_commit_transaction+0x2d15/0x3f20 [jbd2] (inlined by) jbd2_journal_commit_transaction at fs/jbd2/commit.c:1034 kjournald2+0x13b/0x450 [jbd2] kthread+0x1cd/0x1f0 ret_from_fork+0x27/0x50 read to 0xffff99f9b1bd0e30 of 8 bytes by task 25724 on cpu 68: jbd2_write_access_granted+0x1b2/0x250 [jbd2] jbd2_write_access_granted at fs/jbd2/transaction.c:1155 jbd2_journal_get_write_access+0x2c/0x60 [jbd2] __ext4_journal_get_write_access+0x50/0x90 [ext4] ext4_mb_mark_diskspace_used+0x158/0x620 [ext4] ext4_mb_new_blocks+0x54f/0xca0 [ext4] ext4_ind_map_blocks+0xc79/0x1b40 [ext4] ext4_map_blocks+0x3b4/0x950 [ext4] _ext4_get_block+0xfc/0x270 [ext4] ext4_get_block+0x3b/0x50 [ext4] __block_write_begin_int+0x22e/0xae0 __block_write_begin+0x39/0x50 ext4_write_begin+0x388/0xb50 [ext4] generic_perform_write+0x15d/0x290 ext4_buffered_write_iter+0x11f/0x210 [ext4] ext4_file_write_iter+0xce/0x9e0 [ext4] new_sync_write+0x29c/0x3b0 __vfs_write+0x92/0xa0 vfs_write+0x103/0x260 ksys_write+0x9d/0x130 __x64_sys_write+0x4c/0x60 do_syscall_64+0x91/0xb05 entry_SYSCALL_64_after_hwframe+0x49/0xbe 5 locks held by fsync04/25724: #0: ffff99f9911093f8 (sb_writers#13){.+.+}, at: vfs_write+0x21c/0x260 #1: ffff99f9db4c0348 (&sb->s_type->i_mutex_key#15){+.+.}, at: ext4_buffered_write_iter+0x65/0x210 [ext4] #2: ffff99f5e7dfcf58 (jbd2_handle){++++}, at: start_this_handle+0x1c1/0x9d0 [jbd2] #3: ffff99f9db4c0168 (&ei->i_data_sem){++++}, at: ext4_map_blocks+0x176/0x950 [ext4] #4: ffffffff99086b40 (rcu_read_lock){....}, at: jbd2_write_access_granted+0x4e/0x250 [jbd2] irq event stamp: 1407125 hardirqs last enabled at (1407125): [<ffffffff980da9b7>] __find_get_block+0x107/0x790 hardirqs last disabled at (1407124): [<ffffffff980da8f9>] __find_get_block+0x49/0x790 softirqs last enabled at (1405528): [<ffffffff98a0034c>] __do_softirq+0x34c/0x57c softirqs last disabled at (1405521): [<ffffffff97cc67a2>] irq_exit+0xa2/0xc0 Reported by Kernel Concurrency Sanitizer on: CPU: 68 PID: 25724 Comm: fsync04 Tainted: G L 5.6.0-rc2-next-20200221+ #7 Hardware name: HPE ProLiant DL385 Gen10/ProLiant DL385 Gen10, BIOS A40 07/10/2019 The plain reads are outside of jh->b_state_lock critical section which result in data races. Fix them by adding pairs of READ|WRITE_ONCE(). Reviewed-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Qian Cai <cai@lca.pw> Link: https://lore.kernel.org/r/20200222043111.2227-1-cai@lca.pwSigned-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Linus Torvalds authored
[ Upstream commit fda31c50 ] When queueing a signal, we increment both the users count of pending signals (for RLIMIT_SIGPENDING tracking) and we increment the refcount of the user struct itself (because we keep a reference to the user in the signal structure in order to correctly account for it when freeing). That turns out to be fairly expensive, because both of them are atomic updates, and particularly under extreme signal handling pressure on big machines, you can get a lot of cache contention on the user struct. That can then cause horrid cacheline ping-pong when you do these multiple accesses. So change the reference counting to only pin the user for the _first_ pending signal, and to unpin it when the last pending signal is dequeued. That means that when a user sees a lot of concurrent signal queuing - which is the only situation when this matters - the only atomic access needed is generally the 'sigpending' count update. This was noticed because of a particularly odd timing artifact on a dual-socket 96C/192T Cascade Lake platform: when you get into bad contention, on that machine for some reason seems to be much worse when the contention happens in the upper 32-byte half of the cacheline. As a result, the kernel test robot will-it-scale 'signal1' benchmark had an odd performance regression simply due to random alignment of the 'struct user_struct' (and pointed to a completely unrelated and apparently nonsensical commit for the regression). Avoiding the double increments (and decrements on the dequeueing side, of course) makes for much less contention and hugely improved performance on that will-it-scale microbenchmark. Quoting Feng Tang: "It makes a big difference, that the performance score is tripled! bump from original 17000 to 54000. Also the gap between 5.0-rc6 and 5.0-rc6+Jiri's patch is reduced to around 2%" [ The "2% gap" is the odd cacheline placement difference on that platform: under the extreme contention case, the effect of which half of the cacheline was hot was 5%, so with the reduced contention the odd timing artifact is reduced too ] It does help in the non-contended case too, but is not nearly as noticeable. Reported-and-tested-by:
Feng Tang <feng.tang@intel.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Huang, Ying <ying.huang@intel.com> Cc: Philip Li <philip.li@intel.com> Cc: Andi Kleen <andi.kleen@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by:
-
Madhuparna Bhowmik authored
[ Upstream commit 253216ff ] local->sta_mtx is held in __ieee80211_check_fast_rx_iface(). No need to use list_for_each_entry_rcu() as it also requires a cond argument to avoid false lockdep warnings when not used in RCU read-side section (with CONFIG_PROVE_RCU_LIST). Therefore use list_for_each_entry(); Signed-off-by:
Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Link: https://lore.kernel.org/r/20200223143302.15390-1-madhuparnabhowmik10@gmail.comSigned-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Marek Vasut authored
[ Upstream commit 44343418 ] The KS8851 requires that packet RX and TX are mutually exclusive. Currently, the driver hopes to achieve this by disabling interrupt from the card by writing the card registers and by disabling the interrupt on the interrupt controller. This however is racy on SMP. Replace this approach by expanding the spinlock used around the ks_start_xmit() TX path to ks_irq() RX path to assure true mutual exclusion and remove the interrupt enabling/disabling, which is now not needed anymore. Furthermore, disable interrupts also in ks_net_stop(), which was missing before. Note that a massive improvement here would be to re-use the KS8851 driver approach, which is to move the TX path into a worker thread, interrupt handling to threaded interrupt, and synchronize everything with mutexes, but that would be a much bigger rework, for a separate patch. Signed-off-by:
Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Johannes Berg authored
[ Upstream commit a7ee7d44 ] We may end up with a NULL reg_rule after the loop in handle_channel_custom() if the bandwidth didn't fit, check if this is the case and bail out if so. Signed-off-by:
-
Kai-Heng Feng authored
[ Upstream commit be0aba82 ] The Surfbook E11B uses the SIPODEV SP1064 touchpad, which does not supply descriptors, so it has to be added to the override list. BugLink: https://bugs.launchpad.net/bugs/1858299Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Reviewed-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
-
Mansour Behabadi authored
[ Upstream commit e433be92 ] Magic Keyboards with more recent firmware (0x0100) report Fn key differently. Without this patch, Fn key may not behave as expected and may not be configurable via hid_apple fnmode module parameter. Signed-off-by:
Mansour Behabadi <mansour@oxplot.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Jean Delvare authored
[ Upstream commit 3f9e12e0 ] In case the WDAT interface is broken, give the user an option to ignore it to let a native driver bind to the watchdog device instead. Signed-off-by:
Jean Delvare <jdelvare@suse.de> Acked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Kim Phillips authored
[ Upstream commit f967140d ] Enable the sampling check in kernel/events/core.c::perf_event_open(), which returns the more appropriate -EOPNOTSUPP. BEFORE: $ sudo perf record -a -e instructions,l3_request_g1.caching_l3_cache_accesses true Error: The sys_perf_event_open() syscall returned with 22 (Invalid argument) for event (l3_request_g1.caching_l3_cache_accesses). /bin/dmesg | grep -i perf may provide additional information. With nothing relevant in dmesg. AFTER: $ sudo perf record -a -e instructions,l3_request_g1.caching_l3_cache_accesses true Error: l3_request_g1.caching_l3_cache_accesses: PMU Hardware doesn't support sampling/overflow-interrupts. Try 'perf stat' Fixes: c43ca509 ("perf/x86/amd: Add support for AMD NB and L2I "uncore" counters") Signed-off-by:
Kim Phillips <kim.phillips@amd.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Acked-by:
Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20200311191323.13124-1-kim.phillips@amd.comSigned-off-by:
-
Sven Eckelmann authored
commit f4156f96 upstream. The announcement messages of batman-adv COMPAT_VERSION 15 have the possibility to announce additional information via a dynamic TVLV part. This part is optional for the ELP packets and currently not parsed by the Linux implementation. Still out-of-tree versions are using it to transport things like neighbor hashes to optimize the rebroadcast behavior. Since the ELP broadcast packets are smaller than the minimal ethernet packet, it often has to be padded. This is often done (as specified in RFC894) with octets of zero and thus work perfectly fine with the TVLV part (making it a zero length and thus empty). But not all ethernet compatible hardware seems to follow this advice. To avoid ambiguous situations when parsing the TVLV header, just force the 4 bytes (TVLV length + padding) after the required ELP header to zero. Fixes: d6f94d91 ("batman-adv: ELP - adding basic infrastructure") Reported-by:
Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by:
-
Sven Eckelmann authored
commit 88d0895d upstream. The probe ELPs for WiFi interfaces are expanded to contain at least BATADV_ELP_MIN_PROBE_SIZE bytes. This is usually a lot more than the number of bytes which the template ELP packet requires. These extra padding bytes were not initialized and thus could contain data which were previously stored at the same location. It is therefore required to set it to some predefined or random values to avoid leaking private information from the system transmitting these kind of packets. Fixes: e4623c913508 ("batman-adv: Avoid probe ELP information leak") Signed-off-by:
Antonio Quartulli <a@unstable.cc> Signed-off-by:
-
Matthias Schiffer authored
commit bc44b781 upstream. batadv_check_unicast_ttvn() calls skb_cow(), so pointers into the SKB data must be (re)set after calling it. The ethhdr variable is dropped altogether. Fixes: 78fc6bbe0aca ("batman-adv: add UNICAST_4ADDR packet type") Signed-off-by:
Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by:
-
Sven Eckelmann authored
A transmission scheduling for an interface which is currently dropped by batadv_iv_ogm_iface_disable could still be in progress. The B.A.T.M.A.N. V is simply cancelling the workqueue item in an synchronous way but this is not possible with B.A.T.M.A.N. IV because the OGM submissions are intertwined. Instead it has to stop submitting the OGM when it detect that the buffer pointer is set to NULL. Reported-by: syzbot+a98f2016f40b9cd3818a@syzkaller.appspotmail.com Reported-by: syzbot+ac36b6a33c28a491e929@syzkaller.appspotmail.com Fixes: c6c8fea2 ("net: Add batman-adv meshing protocol") Signed-off-by:
-
Sven Eckelmann authored
commit 40e220b4 upstream. Each slave interface of an B.A.T.M.A.N. IV virtual interface has an OGM packet buffer which is initialized using data from netdevice notifier and other rtnetlink related hooks. It is sent regularly via various slave interfaces of the batadv virtual interface and in this process also modified (realloced) to integrate additional state information via TVLV containers. It must be avoided that the worker item is executed without a common lock with the netdevice notifier/rtnetlink helpers. Otherwise it can either happen that half modified/freed data is sent out or functions modifying the OGM buffer try to access already freed memory regions. Reported-by: syzbot+0cc629f19ccb8534935b@syzkaller.appspotmail.com Fixes: c6c8fea2 ("net: Add batman-adv meshing protocol") Signed-off-by:
-
Sven Eckelmann authored
commit a8d23cbb upstream. A B.A.T.M.A.N. V virtual interface has an OGM2 packet buffer which is initialized using data from the netdevice notifier and other rtnetlink related hooks. It is sent regularly via various slave interfaces of the batadv virtual interface and in this process also modified (realloced) to integrate additional state information via TVLV containers. It must be avoided that the worker item is executed without a common lock with the netdevice notifier/rtnetlink helpers. Otherwise it can either happen that half modified data is sent out or the functions modifying the OGM2 buffer try to access already freed memory regions. Fixes: 0da00359 ("batman-adv: OGMv2 - add basic infrastructure") Signed-off-by:
-
Sven Eckelmann authored
commit 9e6b5648 upstream. The state of slave interfaces are handled differently depending on whether the interface is up or not. All active interfaces (IFF_UP) will transmit OGMs. But for B.A.T.M.A.N. IV, also non-active interfaces are scheduling (low TTL) OGMs on active interfaces. The code which setups and schedules the OGMs must therefore already be called when the interfaces gets added as slave interface and the transmit function must then check whether it has to send out the OGM or not on the specific slave interface. But the commit f0d97253 ("batman-adv: remove ogm_emit and ogm_schedule API calls") moved the setup code from the enable function to the activate function. The latter is called either when the added slave was already up when batadv_hardif_enable_interface processed the new interface or when a NETDEV_UP event was received for this slave interfac. As result, each NETDEV_UP would schedule a new OGM worker for the interface and thus OGMs would be send a lot more than expected. Fixes: f0d97253 ("batman-adv: remove ogm_emit and ogm_schedule API calls") Reported-by:
Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by:
-
Sven Eckelmann authored
commit dff9bc42 upstream. The function batadv_gw_node_add is responsible for adding new gw_node to the gateway_list. It is expecting that the caller already checked that there is not already an entry with the same key or not. But the lock for the list is only held when the list is really modified. This could lead to duplicated entries because another context could create an entry with the same key between the check and the list manipulation. The check and the manipulation of the list must therefore be in the same locked code section. Fixes: c6c8fea2 ("net: Add batman-adv meshing protocol") Signed-off-by:
-
Linus Lüssing authored
commit a44ebeff upstream. When a (broken) node wrongly sends multicast TT entries with a ROAM flag then this causes any receiving node to drop all entries for the same multicast MAC address announced by other nodes, leading to packet loss. Fix this DoS vector by only storing TT sync flags. For multicast TT non-sync'ing flag bits like ROAM are unused so far anyway. Fixes: 1d8ab8d3 ("batman-adv: Modified forwarding behaviour for multicast packets") Reported-by:
Leonardo Mörlein <me@irrelefant.net> Signed-off-by:
-
Linus Lüssing authored
commit 4a519b83 upstream. Since commit 54e22f26 ("batman-adv: fix TT sync flag inconsistencies") TT sync flags and TT non-sync'd flags are supposed to be stored separately. The previous patch missed to apply this separation on a TT entry with only a single TT orig entry. This is a minor fix because with only a single TT orig entry the DDoS issue the former patch solves does not apply. Fixes: 54e22f26 ("batman-adv: fix TT sync flag inconsistencies") Signed-off-by:
-
Sven Eckelmann authored
commit 6da7be7d upstream. batman-adv is creating special debugfs directories in the init net_namespace for each created soft-interface (batadv net_device). But it is possible to rename a net_device to a completely different name then the original one. It can therefore happen that a user registers a new batadv net_device with the name "bat0". batman-adv is then also adding a new directory under $debugfs/batman-adv/ with the name "wlan0". The user then decides to rename this device to "bat1" and registers a different batadv device with the name "bat0". batman-adv will then try to create a directory with the name "bat0" under $debugfs/batman-adv/ again. But there already exists one with this name under this path and thus this fails. batman-adv will detect a problem and rollback the registering of this device. batman-adv must therefore take care of renaming the debugfs directories for soft-interfaces whenever it detects such a net_device rename. Fixes: c6c8fea2 ("net: Add batman-adv meshing protocol") Signed-off-by:
-
Sven Eckelmann authored
commit 36dc621c upstream. batman-adv is creating special debugfs directories in the init net_namespace for each valid hard-interface (net_device). But it is possible to rename a net_device to a completely different name then the original one. It can therefore happen that a user registers a new net_device which gets the name "wlan0" assigned by default. batman-adv is also adding a new directory under $debugfs/batman-adv/ with the name "wlan0". The user then decides to rename this device to "wl_pri" and registers a different device. The kernel may now decide to use the name "wlan0" again for this new device. batman-adv will detect it as a valid net_device and tries to create a directory with the name "wlan0" under $debugfs/batman-adv/. But there already exists one with this name under this path and thus this fails. batman-adv will detect a problem and rollback the registering of this device. batman-adv must therefore take care of renaming the debugfs directories for hard-interfaces whenever it detects such a net_device rename. Fixes: 5bc7c1eb ("batman-adv: add debugfs structure for information per interface") Reported-by:
John Soros <sorosj@gmail.com> Signed-off-by:
-
Marek Lindner authored
commit 16116dac upstream. A translation table TVLV changset sent with an OGM consists of a number of headers (one per VLAN) plus the changeset itself (addition and/or deletion of entries). The per-VLAN headers are used by OGM recipients for consistency checks. Said consistency check might determine that a full translation table request is needed to restore consistency. If the TT sender adds per-VLAN headers of empty VLANs into the OGM, recipients are led to believe to have reached an inconsistent state and thus request a full table update. The full table does not contain empty VLANs (due to missing entries) the cycle restarts when the next OGM is issued. Consequently, when the translation table TVLV headers are composed, empty VLANs are to be excluded. Fixes: 21a57f6e7a3b ("batman-adv: make the TT CRC logic VLAN specific") Signed-off-by:
-
Linus Lüssing authored
commit 7072337e upstream. The previous TT sync fix so far only fixed TT responses issued by the target node directly. So far, TT responses issued by intermediate nodes still lead to the wrong flags being added, leading to CRC mismatches. This behaviour was observed at Freifunk Hannover in a 800 nodes setup where a considerable amount of nodes were still infected with 'WI' TT flags even with (most) nodes having the previous TT sync fix applied. I was able to reproduce the issue with intermediate TT responses in a four node test setup and this patch fixes this issue by ensuring to use the per originator instead of the summarized, OR'd ones. Fixes: e9c00136 ("batman-adv: fix tt_global_entries flags update") Reported-by:
-
Sven Eckelmann authored
commit 8ba0f9bd upstream. The functions batadv_tt_prepare_tvlv_local_data and batadv_tt_prepare_tvlv_global_data are responsible for preparing a buffer which can be used to store the TVLV container for TT and add the VLAN information to it. This will be done in three phases: 1. count the number of VLANs and their entries 2. allocate the buffer using the counters from the previous step and limits from the caller (parameter tt_len) 3. insert the VLAN information to the buffer The step 1 and 3 operate on a list which contains the VLANs. The access to these lists must be protected with an appropriate lock or otherwise they might operate on on different entries. This could for example happen when another context is adding VLAN entries to this list. This could lead to a buffer overflow in these functions when enough entries were added between step 1 and 3 to the VLAN lists that the buffer room for the entries (*tt_change) is smaller then the now required extra buffer for new VLAN entries. Fixes: 7ea7b4a1 ("batman-adv: make the TT CRC logic VLAN specific") Signed-off-by:
-
Sven Eckelmann authored
commit f22e0893 upstream. batman-adv uses internal indices for each enabled and active interface. It is currently used by the B.A.T.M.A.N. IV algorithm to identifify the correct position in the ogm_cnt bitmaps. The type for the number of enabled interfaces (which defines the next interface index) was set to char. This type can be (depending on the architecture) either signed (limiting batman-adv to 127 active slave interfaces) or unsigned (limiting batman-adv to 255 active slave interfaces). This limit was not correctly checked when an interface was enabled and thus an overflow happened. This was only catched on systems with the signed char type when the B.A.T.M.A.N. IV code tried to resize its counter arrays with a negative size. The if_num interface index was only a s16 and therefore significantly smaller than the ifindex (int) used by the code net code. Both &batadv_hard_iface->if_num and &batadv_priv->num_ifaces must be (unsigned) int to support the same number of slave interfaces as the net core code. And the interface activation code must check the number of active slave interfaces to avoid integer overflows. Fixes: c6c8fea2 ("net: Add batman-adv meshing protocol") Signed-off-by:
-
Sven Eckelmann authored
commit 5ba7dcfe upstream. The originator node object orig_neigh_node is used to when accessing the bcast_own(_sum) and real_packet_count information. The access to them has to be protected with the spinlock in orig_neigh_node. But the function uses the lock in orig_node instead. This is incorrect because they could be two different originator node objects. Fixes: 0ede9f41 ("batman-adv: protect bit operations to count OGMs with spinlock") Signed-off-by:
-
Sven Eckelmann authored
commit 198a62dd upstream. The batadv_v_gw_is_eligible function already assumes that orig_node is not NULL. But batadv_gw_node_get may have failed to find the originator. It must therefore be checked whether the batadv_gw_node_get failed and not whether orig_node is NULL to detect this error. Fixes: 50164d8f ("batman-adv: B.A.T.M.A.N. V - implement GW selection logic") Signed-off-by:
Sven Eckelmann <sven.eckelmann@openmesh.com> Acked-by:
-
Sven Eckelmann authored
commit fe77d825 upstream. The batman-adv unuicast fragment header contains 3 bits for the priority of the packet. These bits will be initialized when the skb->priority contains a value between 256 and 263. But otherwise, the uninitialized bits from the stack will be used. Fixes: c0f25c80 ("batman-adv: Include frame priority in fragment header") Signed-off-by:
Sven Eckelmann <sven.eckelmann@open-mesh.com> Signed-off-by:
-
Sven Eckelmann authored
commit 6a4bc44b upstream. The neighbor compare API implementation for B.A.T.M.A.N. V checks whether the neigh_ifinfo for this neighbor on a specific interface exists. A warning is printed when it isn't found. But it is not called inside a lock which would prevent that this information is lost right before batadv_neigh_ifinfo_get. It must therefore be expected that batadv_v_neigh_(cmp|is_sob) might not be able to get the requested neigh_ifinfo. A WARN_ON for such a situation seems not to be appropriate because this will only flood the kernel logs. The warnings must therefore be removed. Signed-off-by:
-
Linus Lüssing authored
commit 54e22f26 upstream. This patch fixes an issue in the translation table code potentially leading to a TT Request + Response storm. The issue may occur for nodes involving BLA and an inconsistent configuration of the batman-adv AP isolation feature. However, since the new multicast optimizations, a single, malformed packet may lead to a mesh-wide, persistent Denial-of-Service, too. The issue occurs because nodes are currently OR-ing the TT sync flags of all originators announcing a specific MAC address via the translation table. When an intermediate node now receives a TT Request and wants to answer this on behalf of the destination node, then this intermediate node now responds with an altered flag field and broken CRC. The next OGM of the real destination will lead to a CRC mismatch and triggering a TT Request and Response again. Furthermore, the OR-ing is currently never undone as long as at least one originator announcing the according MAC address remains, leading to the potential persistency of this issue. This patch fixes this issue by storing the flags used in the CRC calculation on a a per TT orig entry basis to be able to respond with the correct, original flags in an intermediate TT Response for one thing. And to be able to correctly unset sync flags once all nodes announcing a sync flag vanish for another. Fixes: e9c00136 ("batman-adv: fix tt_global_entries flags update") Signed-off-by:
-
Sven Eckelmann authored
commit d6289088 upstream. The wifi driver can decide to not provide parts of the station info. For example, the expected throughput of the station can be omitted when the used rate control doesn't provide this kind of information. The B.A.T.M.A.N. V implementation must therefore check the filled bitfield before it tries to access the expected_throughput of the returned station_info. Reported-by:
Alvaro Antelo <alvaro.antelo@gmail.com> Fixes: c833484e ("batman-adv: ELP - compute the metric based on the estimated throughput") Signed-off-by:
-
