WoL is enabled in the suspend callback by setting MagicPacket detection
and disabling all interrupts expect MagicPacket. In the resume path the
driver needs to reset the hardware to rearm the WoL logic, this prevents
the driver from simply restoring the registers and to take advantage of
that ravb was not suspended to reduce resume time. To reset the
hardware the driver closes the device, sets it in reset mode and reopens
the device just like it would do in a normal suspend/resume scenario
without WoL enabled, but it both closes and opens the device in the
resume callback since the device needs to be reset for WoL to work.

One quirk needed for WoL is that the module clock needs to be prevented
from being switched off by Runtime PM. To keep the clock alive the
suspend callback need to call clk_enable() directly to increase the
usage count of the clock. Then when Runtime PM decreases the clock usage
count it won't reach 0 and be switched off.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2017-08-01

Here's our first batch of Bluetooth patches for the 4.14 kernel:

 - Several new USB IDs for the btusb driver
 - Memory leak fix in btusb driver
 - Cleanups & fixes to hci_nokia, hci_serdev and hci_bcm drivers
 - Fixed cleanup path in mrf24j40 (802.15.4) driver probe function
 - A few other smaller cleanups & fixes to drivers

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Skb frags may contain compound pages. Various operations map frags
temporarily using kmap_atomic, but this function works on single
pages, not whole compound pages. The distinction is only relevant
for high mem pages that require temporary mappings.

Introduce a looping mechanism that for compound highmem pages maps
one page at a time, does not change behavior on other pages.
Use the loop in the kmap_atomic callers in net/core/skbuff.c.

Verified by triggering skb_copy_bits with

    tcpdump -n -c 100 -i ${DEV} -w /dev/null &
    netperf -t TCP_STREAM -H ${HOST}

  and by triggering __skb_checksum with

    ethtool -K ${DEV} tx off

  repeated the tests with looping on a non-highmem platform
  (x86_64) by making skb_frag_must_loop always return true.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sean Wang says:

====================
net-next: mediatek: add support for ethernet on MT7622 SoC

Changes since v2:
- update John's mail

Changes since v1:
- add refinement for ethernet clock management
- take out the code block for ESW, add it until ESW driver is actually introduced

The series adds the driver for ethernet controller found on MT7622 SoC.
There are additions against with previous MT7623 SoC such as shared SGMII
given for the dual GMACs and built-in 5-ports 10/100 embedded switch support
(ESW). Thus more clocks consumers and SGMII hardware setup for the extra
features are all introduced here and as for the support for ESW that would be
planned to add in the separate patch integrating with DSA infrastructure
in the future.

Currently testing successfully is done with those patches for the conditions
such as GMAC2 with IP1001 PHY via RGMII and GMAC1/2 with RTL8211F PHY via SGMII.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Sean and Nelson work for MediaTek on maintaining the MediaTek ethernet
driver for the existing SoCs and adding support for the following SoCs.
In the past, Sean has been active at making most of the qualifications
, stress test and submitting a lot of patches for the driver while
Nelson was looking into the aspects more on hardware additions and details
such as introducing PDMA with Hardware LRO to the driver. Also update
John's up-to-date mail address in the patch.

Cc: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the driver for ethernet controller on MT7622 SoC. It has
the similar handling logic as the previously MT7623 does, but there are
additions against with MT7623 SoC, the shared SGMII given for the dual
GMACs and including 5-ports 10/100 embedded switch support (ESW) as the
GMAC1 option, thus more clocks consumers for the extra feature are
introduced here. So for ease portability and maintenance, those
differences all are being kept inside the platform data as other drivers
usually do. Currently testing successfully is done with those patches for
the conditions such as GMAC2 with IP1001 PHY via RGMII and GMAC1/2 with
RTL8211F PHY via SGMII.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is the preparation patch in order to adapt into various
hardware through adding platform data which holds specific characteristics
among MediaTek SoCs and introducing the unified clock handler for those
distinct clock requirements depending on different features such as
TRGMII and SGMII getting support on the target SoC. And finally, add
enhancement with given the generic description for Kconfig and remove the
unnecessary machine type dependency in Makefile.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds the supplements in the dt-binding document for MediaTek
MT7622 SoC with extra SGMII system controller and relevant clock consumers
listed as the requirements for those SoCs equipped with the SGMII circuit.
Also, add the missing binding information for MT7623 SoC here which relies
on the fallback binding of MT2701.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
net: Infrastructure changes for [kz]proxy

This patch set contains some general infrastructure enhancements that
will be used by kernel proxy and zero proxy.

The changes are:
  - proto_ops: Add locked versions of sendmsg and sendpage
  - skb_send_sock: Allow sending and skb on a socket within the
    kernel
  - Generalize strparser. Allow it to be used in other contexts than
    just in the read_sock path. This will be used in the transmit
    path of zero proxy.

Some nice future work (which I've been discussing with John Fastabend)
will be to make some of the related functions to allow gifting of skbs
We should be able to do that with skb_send_sock and strp_process. I'd
also like this feature in the read_sock callbeck.

Tested: Ran modified kernel without incident. Tested new functionality
using zero proxy (in development).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Generalize strparser from more than just being used in conjunction
with read_sock. strparser will also be used in the send path with
zero proxy. The primary change is to create strp_process function
that performs the critical processing on skbs. The documentation
is also updated to reflect the new uses.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add skb_send_sock to send an skbuff on a socket within the kernel.
Arguments include an offset so that an skbuf might be sent in mulitple
calls (e.g. send buffer limit is hit).
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new proto_ops sendmsg_locked and sendpage_locked that can be
called when the socket lock is already held. Correspondingly, add
kernel_sendmsg_locked and kernel_sendpage_locked as front end
functions.

These functions will be used in zero proxy so that we can take
the socket lock in a ULP sendmsg/sendpage and then directly call the
backend transport proto_ops functions.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>

Julia Lawall says:

====================
Revert "ipv6: constify inet6_protocol structures"

inet6_add_protocol and inet6_del_protocol include casts that remove the
effect of the const annotation on their parameter, leading to possible
runtime crashes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit d04916a4.

inet6_add_protocol and inet6_del_protocol include casts that remove the
effect of the const annotation on their parameter, leading to possible
runtime crashes.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 3a3a4e30.

inet6_add_protocol and inet6_del_protocol include casts that remove the
effect of the const annotation on their parameter, leading to possible
runtime crashes.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Handle notifier registry failures properly in tun/tap driver, from
    Tonghao Zhang.

 2) Fix bpf verifier handling of subtraction bounds and add a testcase
    for this, from Edward Cree.

 3) Increase reset timeout in ftgmac100 driver, from Ben Herrenschmidt.

 4) Fix use after free in prd_retire_rx_blk_timer_exired() in AF_PACKET,
    from Cong Wang.

 5) Fix SElinux regression due to recent UDP optimizations, from Paolo
    Abeni.

 6) We accidently increment IPSTATS_MIB_FRAGFAILS in the ipv6 code
    paths, fix from Stefano Brivio.

 7) Fix some mem leaks in dccp, from Xin Long.

 8) Adjust MDIO_BUS kconfig deps to avoid build errors, from Arnd
    Bergmann.

 9) Mac address length check and buffer size fixes from Cong Wang.

10) Don't leak sockets in ipv6 udp early demux, from Paolo Abeni.

11) Fix return value when copy_from_user() fails in
    bpf_prog_get_info_by_fd(), from Daniel Borkmann.

12) Handle PHY_HALTED properly in phy library state machine, from
    Florian Fainelli.

13) Fix OOPS in fib_sync_down_dev(), from Ido Schimmel.

14) Fix truesize calculation in virtio_net which led to performance
    regressions, from Michael S Tsirkin.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  samples/bpf: fix bpf tunnel cleanup
  udp6: fix jumbogram reception
  ppp: Fix a scheduling-while-atomic bug in del_chan
  Revert "net: bcmgenet: Remove init parameter from bcmgenet_mii_config"
  virtio_net: fix truesize for mergeable buffers
  mv643xx_eth: fix of_irq_to_resource() error check
  MAINTAINERS: Add more files to the PHY LIBRARY section
  ipv4: fib: Fix NULL pointer deref during fib_sync_down_dev()
  net: phy: Correctly process PHY_HALTED in phy_stop_machine()
  sunhme: fix up GREG_STAT and GREG_IMASK register offsets
  bpf: fix bpf_prog_get_info_by_fd to dump correct xlated_prog_len
  tcp: avoid bogus gcc-7 array-bounds warning
  net: tc35815: fix spelling mistake: "Intterrupt" -> "Interrupt"
  bpf: don't indicate success when copy_from_user fails
  udp6: fix socket leak on early demux
  net: thunderx: Fix BGX transmit stall due to underflow
  Revert "vhost: cache used event for better performance"
  team: use a larger struct for mac address
  net: check dev->addr_len for dev_set_mac_address()
  phy: bcm-ns-usb3: fix MDIO_BUS dependency
  ...

Contains a QCA6174A-5 chipset, with USB BT. Let's support loading
firmware on it.

From usb-devices:
T:  Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3016 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

test_tunnel_bpf.sh fails to remove the vxlan11 tunnel device, causing the
next geneve tunnelling test case fails.  In addition, the geneve reserved bit
in tcbpf2_kern.c should be zero, according to the RFC.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 67a51780 ("ipv6: udp: leverage scratch area
helpers") udp6_recvmsg() read the skb len from the scratch area,
to avoid a cache miss.
But the UDP6 rx path support RFC 2675 UDPv6 jumbograms, and their
length exceeds the 16 bits available in the scratch area. As a side
effect the length returned by recvmsg() is:
<ingress datagram len> % (1<<16)

This commit addresses the issue allocating one more bit in the
IP6CB flags field and setting it for incoming jumbograms.
Such field is still in the first cacheline, so at recvmsg()
time we can check it and fallback to access skb->len if
required, without a measurable overhead.

Fixes: 67a51780 ("ipv6: udp: leverage scratch area helpers")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PPTP set the pptp_sock_destruct as the sock's sk_destruct, it would
trigger this bug when __sk_free is invoked in atomic context, because of
the call path pptp_sock_destruct->del_chan->synchronize_rcu.

Now move the synchronize_rcu to pptp_release from del_chan. This is the
only one case which would free the sock and need the synchronize_rcu.

The following is the panic I met with kernel 3.3.8, but this issue should
exist in current kernel too according to the codes.

BUG: scheduling while atomic
__schedule_bug+0x5e/0x64
__schedule+0x55/0x580
? ppp_unregister_channel+0x1cd5/0x1de0 [ppp_generic]
? dev_hard_start_xmit+0x423/0x530
? sch_direct_xmit+0x73/0x170
__cond_resched+0x16/0x30
_cond_resched+0x22/0x30
wait_for_common+0x18/0x110
? call_rcu_bh+0x10/0x10
wait_for_completion+0x12/0x20
wait_rcu_gp+0x34/0x40
? wait_rcu_gp+0x40/0x40
synchronize_sched+0x1e/0x20
0xf8417298
0xf8417484
? sock_queue_rcv_skb+0x109/0x130
__sk_free+0x16/0x110
? udp_queue_rcv_skb+0x1f2/0x290
sk_free+0x16/0x20
__udp4_lib_rcv+0x3b8/0x650
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 28b45910 ("net: bcmgenet: Remove init parameter
from bcmgenet_mii_config") because in the process of moving from
dev_info() to dev_info_once() we essentially lost the helpful printed
messages once the second instance of the driver is loaded.
dev_info_once() does not actually print the message once per device
instance, but once period.

Fixes: 28b45910 ("net: bcmgenet: Remove init parameter from bcmgenet_mii_config")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Seth Forshee noticed a performance degradation with some workloads.
This turns out to be due to packet drops.  Euan Kemp noticed that this
is because we drop all packets where length exceeds the truesize, but
for some packets we add in extra memory without updating the truesize.
This in turn was kept around unchanged from ab7db917 ("virtio-net:
auto-tune mergeable rx buffer size for improved performance").  That
commit had an internal reason not to account for the extra space: not
enough bits to do it.  No longer true so let's account for the allocated
length exactly.

Many thanks to Seth Forshee for the report and bisecting and Euan Kemp
for debugging the issue.

Fixes: 680557cf ("virtio_net: rework mergeable buffer handling")
Reported-by: Euan Kemp <euan.kemp@coreos.com>
Tested-by: Euan Kemp <euan.kemp@coreos.com>
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to go through sk->sk_net to access the net namespace
and its sysctl variables because we allocate the sock and initialize
sk_net just a few lines earlier in the same routine.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
More Marvell PHY refactoring and cleanup

Consolidate more duplicated code into helpers, make use of core
helpers, move code into a helper for later adding functionality to add
marvell PHYs, etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The 1116r has code to set downshift. Refactor this into a helper, so
in future other marvell PHYs can use it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of the init functions unilaterally enable set auto cross over
without using the helper. Make use of the helper, and respect the
phydev MDI configuration.

Clean up the #define used while setting polarity, and the other
functions of the bits in the register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Turns out that MII_M1116R_CONTROL_REG_MAC is the same as
MII_88E1121_PHY_MSCR_REG. Refactor the code to set the RGMII delays
into a shared helper.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same code is repeated a few times. Refactor into a helped.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same code is repeated for different PHY versions. Put it into a
help and call when needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than using an open coded equivalent, use the core
genphy_soft_reset() function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert spaces to tabs where appropriate, and fix up some otherwise
odd indentation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

of_irq_to_resource() has recently been  fixed to return negative error #'s
along with 0 in case of failure,  however the Marvell MV643xx Ethernet
driver still only regards 0  as invalid IRQ -- fix it up.

Fixes: 7a4228bb ("of: irq: use of_irq_get() in of_irq_to_resource()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver needs CONFIG_HAS_IOMEM and OF to be functional, but we still
let it build with COMPILE_TEST. This fixes the unmet dependency after
selecting MDIO_BCM_UNIMAC in commit mentioned below:

warning: (NET_DSA_BCM_SF2 && BCMGENET) selects MDIO_BCM_UNIMAC which has
unmet direct dependencies (NETDEVICES && MDIO_DEVICE && HAS_IOMEM &&
OF_MDIO)

Fixes: 9a4e7969 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Include missing files that are provided by, used, or directly maintained
within the PHY LIBRARY, this include uapi header, header files used by
Device Tree code etc.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michał reported a NULL pointer deref during fib_sync_down_dev() when
unregistering a netdevice. The problem is that we don't check for
'in_dev' being NULL, which can happen in very specific cases.

Usually routes are flushed upon NETDEV_DOWN sent in either the netdev or
the inetaddr notification chains. However, if an interface isn't
configured with any IP address, then it's possible for host routes to be
flushed following NETDEV_UNREGISTER, after NULLing dev->ip_ptr in
inetdev_destroy().

To reproduce:
$ ip link add type dummy
$ ip route add local 1.1.1.0/24 dev dummy0
$ ip link del dev dummy0

Fix this by checking for the presence of 'in_dev' before referencing it.

Fixes: 982acb97 ("ipv4: fib: Notify about nexthop status changes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc reported that he was not getting the PHY library adjust_link()
callback function to run when calling phy_stop() + phy_disconnect()
which does not indeed happen because we set the state machine to
PHY_HALTED but we don't get to run it to process this state past that
point.

Fix this with a synchronous call to phy_state_machine() in order to have
the state machine actually act on PHY_HALTED, set the PHY device's link
down, turn the network device's carrier off and finally call the
adjust_link() function.
Reported-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Fixes: a390d1f3 ("phylib: convert state_queue work to delayed_work")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the following stats into SCM_TIMESTAMPING_OPT_STATS control msg:
    TCP_NLA_PACING_RATE
    TCP_NLA_DELIVERY_RATE
    TCP_NLA_SND_CWND
    TCP_NLA_REORDERING
    TCP_NLA_MIN_RTT
    TCP_NLA_RECUR_RETRANS
    TCP_NLA_DELIVERY_RATE_APP_LMT
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor the code to extract the function to compute delivery rate.
This function will be used in later commit.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the values to match those from the STP2002QFP documentation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>