- 07 May, 2018 40 commits
-
-
Sergio Paracuellos authored
Use ether_addr_copy to copy ethernet address instad of using memcpy in ks_wlan_set_mac_address function. Signed-off-by:
Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sergio Paracuellos authored
This commit refactor hostif_sme_power_mgmt_set avoiding to use switch-case statement and simplifying data paths. This improves readability. Signed-off-by:
-
Sergio Paracuellos authored
Parameters for hostif_power_mgmt_request are declared as unsigned long and then are forced to be change to be u32. Also the caller declares explicitly unsigned long parameters just to assign them and pass into the function. Change types for those to be u32 instead so no conversion is needed at all and code gets more clear. Signed-off-by:
-
Sergio Paracuellos authored
This commit make use of two introduced local variables to make more readable code of hostif_sme_set_rsn function. It just assign those local variables in different cases where are needed and extract common code to assign them at the end. Signed-off-by:
-
Sergio Paracuellos authored
Add blank line after definitions in hostif_aplist_init function to fix a checkpatch script complain about that. Signed-off-by:
-
Sergio Paracuellos authored
Fix some checkpatch complains about long lines in some parts of the code. It also fix some lines where spaces instead of tabs were inserted. Signed-off-by:
-
Sergio Paracuellos authored
In all functions related with requests to the device the same patter in used and is also adding a comment to make clear the intention of the code. Just factor out the pattern into a new send_request_to_device function to improve readability and make clear code intention. Signed-off-by:
-
Sergio Paracuellos authored
WLAN_EID_DS_PARAMS case inside switch case is just doing nothing and it is located inside other cases. There is a place inside the switch with other don't do anything cases are located. Move this to that place. Signed-off-by:
-
Sergio Paracuellos authored
This commit make use of ether_addr_copy to copy ethernet address instead of copy it using memcpy. Signed-off-by:
-
Sergio Paracuellos authored
Use ether_addr_copy kernel function to copy an ethernet address instead of a simple memcpy with ETH_ALEN size. Signed-off-by:
-
Sergio Paracuellos authored
Field rsn_enabled included in wpa_status struct is declared as unsigned int but it is only be set using 0 and 1 values and in conditional if code is just being used as a boolean. Change its type to be a boolean. Signed-off-by:
-
Sergio Paracuellos authored
Comments which say the same as the code are not useful at all so just remove them. Signed-off-by:
-
Sergio Paracuellos authored
This commit avoid two checkpatch script complains about two long lines. Signed-off-by:
-
Sergio Paracuellos authored
In ks_wlan_translate_scan function there are two preprocessor definitions: - RSN_INFO_ELEM_ID - GENERIC_INFO_ELEM_ID These can be moved to common ks_wlan.h because they can be used in get_current_ap function instead of use hardcoded values. GENERIC_INFO_ELEM_ID has been renamed to WPA_INFO_ELEM_ID which is more clear. Signed-off-by: -
Sergio Paracuellos authored
Instead of use memcpy to copy ethernet addresses use ether_addr_copy created for that. Signed-off-by:
-
Sergio Paracuellos authored
New three functions have been created to centralice and simplify calls related with set MIB requests: - hostif_mib_set_request_int - hostif_mib_set_request_bool - hostif_mib_set_request_ostring Using these in different calls simplify functions related with this mainly when types are bool and int because no more conversions are needed in the caller functions. Those conversion details are now located in the new helpers improving a lot readability. Calls in hostif_sme_set_wep function has change also some if's to check invalid value first avoiding one level indentation. Signed-off-by: -
Sergio Paracuellos authored
This commit changes parameter types to use enum mib_attribute, enum mib_data_type and size_t for size instead of unsigned short. It also reorder them in a more sense way. Code is updated in different calls to use new parameters order using 'size' auxiliar local variables in some of them to improve readability a bit. Signed-off-by:
-
Sergio Paracuellos authored
This commit changes some type cast in rate related preprocessor definitions included in ks_hostif header file to use preferred u8 type. Signed-off-by:
-
Sergio Paracuellos authored
This commit just change some preprocessor definitions related with MIB attributes into an enumeration which is much cleaner for this here. Also add kerneldoc to avoid long comment lines. Signed-off-by:
-
Sergio Paracuellos authored
This commit just change some preprocessor definitions related with MIB data types into an enumeration which is much cleaner for this here. Signed-off-by:
-
Sergio Paracuellos authored
This commit cleans code for the event SME_MIC_FAILURE_REQUEST changing if logic to handle invalid value first and using a local variable. Signed-off-by:
-
Sergio Paracuellos authored
Header file ks_wlan.h has a lot of nonsense comments along the different declarations included on it. Most of them are just the same as the variable name. Just remove them all. Signed-off-by:
-
Sergio Paracuellos authored
Local variable event in ks_wlan_hw_rx function is declared as unsigned short and can be declared as u16 which is preferred style. Signed-off-by:
-
Sergio Paracuellos authored
Event to send to init the card are always the same so change code to be more readable putting them into an array and enqueuing also using a for loop. Signed-off-by:
-
Sergio Paracuellos authored
Declaration of second parameter 'event' in ks_hostif .h and .c file is different using uint16_t and unsigned short respectively. Just unify both using 'u16' which is preferred instead. Signed-off-by:
-
Sergio Paracuellos authored
Local variable 'byte' in ks7010_sdio_init_irqs is declared as unsigned char and can be declared as u8 which is preferred. It is being used in calls to ks7010_sdio_writeb which is already expected an u8. Signed-off-by:
-
Sergio Paracuellos authored
Local variables 'status', 'rsize' and 'byte' are declared as unsigned char and can be declared as u8 which is preferred. They are being used in ks7010_sdio_readb calls which is already expected an u8. Signed-off-by:
-
Sergio Paracuellos authored
Local variable 'byte' in ks7010_rw_function is declared as unsigned char and can be declared as u8 which is preferred. It is being used in ks7010_sdio_readb which is already expecting an u8. Signed-off-by:
-
Sergio Paracuellos authored
Local variable 'byte' in _ks_wlan_hw_power_save function is declared as unsigned char and can be declared as u8 which is preferred. It is being using with ks7010_sdio_readb which expects u8 already. Signed-off-by:
-
Sergio Paracuellos authored
Parameter buffer in write_to_device function is declared as a pointer to unsigned char and can be declared as an u8 type which is preferred. Internally it calls to ks7010_sdio_write which is using also u8 as parameter type. Update calls to this function as well. Signed-off-by:
-
Sergio Paracuellos authored
Commit 92c1552c removes WPS hardcoded definition and its related conditional preprocessor code. There was some missing stuff already in this files. Remove it. Signed-off-by:
-
Sergio Paracuellos authored
This commit avoids a long line changing a bit message in _ks_wlan_hw_power_save function. Signed-off-by:
-
Sergio Paracuellos authored
ks_wlan_private struct has a pointer to struct ks_sdio_card in its fields. Because of that a forward declaration in needed in ks_wlan.h header and also it makes necessary to have ks_sdio_card public in a ks7010_sdio.h header. Changing this pointer into a void pointer makes no longer necessary to have ks7010_sdio.h header as well as removes the forward dependency in ks_wlan.h. Declaration of ks_sdio_card has been moved to ks7010_sdio.c source file and To make code cleaner inside this file a new ks7010_to_func function has been added. The code has been updated to this changes. Signed-off-by:
-
Sergio Paracuellos authored
There are some definitions for rx and tx queues in ks7010_sdio which is not the best place to put them. Changing them into the ks_wlan header file there is no need to explicity include ks7010_sdio.h which makes no sense at all and can be resolved easily using forward declarations. The functions related with the queues circular buffers have been moved also into this header. Signed-off-by:
-
Sergio Paracuellos authored
It's good to have SPDX identifiers in all files to make it easier to audit the kernel tree for correct licenses. Fix up the all of the staging ks7010 files to have a proper SPDX identifier, based on the license text in the file itself. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. Extra GPL text wording can be removed as it is no longer needed at all. Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistakes in message text and comments "dismatch" -> "mismatch" "Inviation" -> "Invitation" Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Tim Collier authored
Several of the wlan-ng header files had C++-style SPDX comments. Fixed checkpatch warnings by replacing with C-style comments, as per the kernel docs. Signed-off-by:
Tim Collier <osdevtc@gmail.com> Signed-off-by:
-
Tim Collier authored
Fix checkpatch warning due to line break after '(', leaving an over 80 character warning due to long macro name. Signed-off-by: -
Tim Collier authored
Fix checkpatch warning for missing parameter name for function prototype. Signed-off-by:
-
Efstratios Gavas authored
Fixed format/style issues found with checkpatch. No code changes. Corrected alignment of variables after open parenthesis and line breaks. Checkpatch now returns clean except for "line over 80 char" warnings. Signed-off-by:
Efstratios Gavas <xtrat@elg.io> Signed-off-by:
-
