- 03 Aug, 2005 4 commits
-
-
James Bottomley authored
There's a slight problem in the way you've done the transport parameters; reading from the variables actually produces the current settings, not the ones you just set (and there's usually a lag because devices don't renegotiate until the next command goes over the bus). If you set the bit immediately, you get into the situation where the transport parameters report something as being set even if the drive cannot support it. I patched the driver to do it this way and also corrected a panic in the proc routines. Signed-off-by:James Bottomley <James.Bottomley@SteelEye.com>
-
Hannes Reinecke authored
This patch updates various scsi_transport_spi parameters with the actual parameters used by the driver internally. Domain Validation for all devices should now work properly. Signed-off-by: -
Hannes Reinecke authored
This patch updates the aic79xx driver to take advantage of the scsi_transport_spi infrastructure. Patch is quite a mess as some procedures have been reshuffled to be closer to the aic7xxx driver. Rejections fixed and Signed-off-by: -
Hannes Reinecke authored
From: Jeff Garzik <jgarzik@pobox.com> This patch removes the busyq in aic79xx and uses the command-queue from the midlayer instead. Additionally some dead code is removed. Signed-off-by:
Hannes Reinecke <hare@suse.de> Fixed rejections Signed-off-by:
-
- 02 Aug, 2005 9 commits
-
-
Christoph Hellwig authored
Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
Thiemo Seufer <ths@linux-mips.org> Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
-
Christoph Hellwig authored
we have the most recent microcode, make sure to always load it. Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
-
Christoph Hellwig authored
print message tidy ups and some excess brace removal. Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
-
- 30 Jul, 2005 6 commits
-
-
James Bottomley authored
Fixes up some warnings in the tree. Signed-off-by: -
Mike Anderson authored
Add support to not allow additions to a host when it is being removed. Signed-off-by:
Mike Anderson <andmike@us.ibm.com> Signed-off-by:
-
Mike Anderson authored
Remove the old scsi_host_cancel function as it has not been working for sometime do to the device list possibly being empty when it is called and possible race issues. Add setting of SHOST_CANCEL at the state of beginning of scsi_remove_host. Signed-off-by:
-
Mike Anderson authored
Migrate the current SCSI host state model to a model like SCSI device is using. Signed-off-by:
-
Adrian Bunk authored
It seems very unlikely that this driver will go into any stable kernel before devfs will be removed. Signed-off-by:
Adrian Bunk <bunk@stusta.de> Cc: James Bottomley <James.Bottomley@steeleye.com> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
-
Olaf Hering authored
aic doesnt work anymore after this change which appeared int 2.6.13-rc1: [SCSI] aic7xxx/aic79xx: remove useless byte order macro cruft 2 files did not include byteorder.h, aic died with panic "Unknown opcode encountered in seq program" This patch fixes it for me. Signed-off-by:
Olaf Hering <olh@suse.de> Signed-off-by:
-
- 29 Jul, 2005 21 commits
-
-
Matthew Garrett authored
When leaving S3 state, the AGP bridge may not have all PCI configuration registers set in the same way as they were at boot. This should be fixed by pci_restore_state - however, the APBASE register cannot be set to conflict with the APSIZE register. If APSIZE is larger than it was before suspend, pci_restore_state will not restore APBASE correctly. The attached patch adds an extra item to the agp_bridge_data structure and uses it to store the value of APBASE. On resume, this is then written after APSIZE has been set. This patch only touches the path used for Intel chipsets without integrated graphics, and may need to be extended to work with the others. Without this patch, I get the symptoms described in bug 4921 - APBASE ends up overlapping various PCI devices, and as a result they fail to work after resume. Signed-off-by:
Matthew Garrett <mjg59@srcf.ucam.org> Acked-by:
Dave Jones <davej@redhat.com> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Gerald Schaefer authored
Fix inline assembly that gets miscompiled by gcc 4. Signed-off-by:
Gerald Schaefer <geraldsc@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Cornelia Huck authored
Close a small window where a device may be not operational again after senseid finished and the "same device" check fails due to dev=0000 by checking for dnv after stsch() by then setting the device to not operational. (No need to check for dnv in ccw_device_handle_oper() again since we don't do stsch() into the subchannel's schib in the meantime and will get a crw anyway if the device becomes not oper again). Signed-off-by:
Cornelia Huck <cohuck@de.ibm.com> Signed-off-by:
-
Heiko Carstens authored
The patch that introduced waiting for interrupts after resetting the reader can cause the boot to fail because the system is waiting for an interrupt that will never arrive. Add code to check if an interrupt is supposed to arrive before waiting endlessly. Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
-
Martin Schwidefsky authored
Update default configuration of s390. Signed-off-by:
-
Jeff Dike authored
The #if/#ifdef cleanup exposed a bug in UML's ELF header processing. With this bug fixed, UML recognizes the vsyscall info coming from the host. On FC4, there is a vsyscall page low in the address space, which UML doesn't provide. This causes an infinite page fault loop and a hang on boot. This patch works around that by making this look like a no-vsyscall system. Signed-off-by:
Jeff Dike <jdike@addtoit.com> Signed-off-by:
-
Antonino A. Daplas authored
Do not use memcpy in fb_pad_aligned_buffer. It is suboptimal because only a few bytes are moved at a time. Replace with a for-loop. Signed-off-by:
Antonino Daplas <adaplas@pol.net> Signed-off-by:
-
Natalie.Protasevich@unisys.com authored
The patch addresses a problem with ACPI SCI interrupt entry, which gets re-used, and the IRQ is assigned to another unrelated device. The patch corrects the code such that SCI IRQ is skipped and duplicate entry is avoided. Second issue came up with VIA chipset, the problem was caused by original patch assigning IRQs starting 16 and up. The VIA chipset uses 4-bit IRQ register for internal interrupt routing, and therefore cannot handle IRQ numbers assigned to its devices. The patch corrects this problem by allowing PCI IRQs below 16. Signed-off by: Natalie Protasevich <Natalie.Protasevich@unisys.com> Signed-off-by:
-
Antonino A. Daplas authored
>> vesafb: mode is 800x600x16, linelength=1600, pages=16 >> vesafb: scrolling: redraw >> vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 >> mtrr: type mismatch for fc000000,1000000 old: write-back new: write- >> combining Range is already set to write-back, vesafb attempts to add a write-combining mtrr (default for vesafb). >> mtrr: size and base must be multiples of 4 kiB This is a bug, vesafb attempts to add a size < PAGE_SIZE triggering the messages below. To eliminate the warning messages, you can add the option mtrr:2 to add a write-back mtrr for vesafb. Or just use nomtrr option. 1. Fix algorithm for finding the best power of 2 size with mtrr_add(). 2. Add option to choose the mtrr type by extending the mtrr boot option: mtrr:n where n 0 = no mtrr (equivalent to using the nomtrr option) 1 = uncachable 2 = write back 3 = write combining (default) 4 = write through Signed-off-by: -
Bjorn Helgaas authored
Add support for UARTs in MMIO space and clean up a little whitespace. HP legacy-free ia64 machines need this. Signed-off-by:
Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by:
-
Eric W. Biederman authored
sync_tsc was using smp_call_function to ask the boot processor to report it's tsc value. smp_call_function performs an IPI_send_allbutself which is a broadcast ipi. There is a window during processor startup during which the target cpu has started and before it has initialized it's interrupt vectors so it can properly process an interrupt. Receveing an interrupt during that window will triple fault the cpu and do other nasty things. Why cli does not protect us from that is beyond me. The simple fix is to match ia64 and provide a smp_call_function_single. Which avoids the broadcast and is more efficient. This certainly fixes the problem of getting stuck on boot which was very easy to trigger on my SMP Hyperthreaded Xeon, and I think it fixes it for the right reasons. Minor changes by AK Signed-off-by:
Eric W. Biederman <ebiederm@xmission.com> Signed-off-by:
Andi Kleen <ak@suse.de> Signed-off-by:
-
Ravikiran G Thirumalai authored
While reserving KVA for lmem_maps of node, we have to make sure that node_remap_start_pfn[] is aligned to a proper pmd boundary. (node_remap_start_pfn[] gets its value from node_end_pfn[]) Signed-off-by:
Ravikiran Thirumalai <kiran@scalex86.org> Signed-off-by:
Shai Fultheim <shai@scalex86.org> Signed-off-by:
-
Linus Torvalds authored
-
Pete Zaitcev authored
It seems that I see a bug in hidinput_hid_event. The check for NULL can never work, becaue &hidinput->input is nonzero at all times. Cc: <vojtech@suse.cz> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by:
-
Dan Streetman authored
This patch does the same swap, i.e. use the ISO macro if (isoc). Additionally, it fixes the return value - the usb_calc_bus_time function returns the time in nanoseconds (I didn't notice that before) while the HS_USECS and HS_USECS_ISO are microseconds. This fixes the function to return nanoseconds always, and adjusts ehci-q.c (the only high-speed caller of the function) to wrap the call in NS_TO_US(). Signed-off-by:
Dan Streetman <ddstreet@ieee.org> Signed-off-by:
-
Conger, Chris A authored
Compare endpoint address to USB_ENDPOINT_DIR_MASK to determine endpoint direction... From: "Conger, Chris A." <CHRIS.A.CONGER@saic.com> Signed-off-by:
-
Ben Dooks authored
USB (OHCI) Host driver for S3C2410/S3C2440 based systems Signed-off-by:
Ben Dooks <ben-linux@fluff.org> Signed-off-by:
-
Mathieu authored
Gigabyte GN-WLBZ201 wifi usb dongle works very well, using the zd1201 driver. the only missing part is that the corresponding usbid is not declared. The following patch should fix this. From: "Mathieu" <matt@minas-morgul.org> Signed-off-by:
-
Masahito Omote authored
This patch enables a support of KYOCERA AH-K3001V, one of the most popular cell phone in Japan. This device has vendor specific ID but works with acm driver by adding USB ID. This device already works on FreeBSD and OS X by native USB ACM driver with USB ID added. This device is probed as NO_UNION_NORMAL not to hang up when probing. Signed-off-by:
Masahito Omote <omote@utyuuzin.net> Signed-off-by:
-
Michael Hund authored
below you will find the forgotten kmalloc check (sorry). Signed-off-by:
Michael Hund <mhund@ld-didactic.de> Signed-off-by:
-
Alan Stern authored
This patch handles a rarely-encountered failure mode in usbcore. It's legal for device_add to fail (although now it happens even more rarely than before since failure to bind a driver is no longer fatal). So when we destroy the interfaces in a configuration, we shouldn't try to delete ones which weren't successfully registered. Also, failure to register an interface shouldn't be fatal either -- I think; you may disagree about this part of the patch. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
