- 13 Sep, 2014 40 commits
-
-
Alexander Duyck authored
This change corrects an error seen when DSA tagging is built as a module. Without this change it is not possible to get XDSA tagged frames as the test for tagging is stripped by the #ifdef check. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Bo Shen authored
Print the IP revision when probing. Signed-off-by:
Bo Shen <voice.shen@atmel.com> Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
-
David S. Miller authored
Frank Li says: ==================== net: fec: imx6sx multiqueue support These patches enable i.MX6SX multi queue support. i.MX6SX support 3 queue and AVB feature. Change from v3 to v4 - use "unsigned int" instead of "unsigned" Change from v2 to v3 - fixed alignment requirement for ARM and NO-ARM platform Change from v1 to v2. - Change num_tx_queue to unsigned int - Avoid block non-dt platform - remove call netif_set_real_num_rx_queues - seperate multi queue patch two part, one is tx and rx handle, with fixed queue 0 then other one is initilized multiqueue - use two difference alignment for tx and rx path ==================== Signed-off-by: -
Frank Li authored
Enable 3 queues suppport for ethernet Signed-off-by:
Frank Li <Frank.Li@freescale.com> Signed-off-by:
-
Frank Li authored
This patch update fec devicetree binding doc that add Optional properties "fsl,num-tx-queues" and "fsl,num-rx-queues". Signed-off-by:Fugang Duan <B38611@freescale.com> Signed-off-by:
-
Fugang Duan authored
Software clear the MDIO interrupt before MDIO bus access, but MAC still generate MDIO interrupt. The issue only happen on imx6slx chip. CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.0-rc1-00399-g0bcad17 #315 Backtrace: [<800121fc>] (dump_backtrace) from [<800124e0>] (show_stack+0x18/0x1c) r6:8096e534 r5:8096e534 r4:00000000 r3:00000000 [<800124c8>] (show_stack) from [<806a4c60>] (dump_stack+0x8c/0xa4) [<806a4bd4>] (dump_stack) from [<80060ab8>] (__lock_acquire+0x1814/0x1c40) r6:be078000 r5:be074000 r4:be03f6e4 r3:be078000 [<8005f2a4>] (__lock_acquire) from [<800616e0>] (lock_acquire+0x70/0x84) r10:809ada33 r9:be010600 r8:00000096 r7:00000001 r6:be074000 r5:00000000 r4:60000193 [<80061670>] (lock_acquire) from [<806abb20>] (_raw_spin_lock_irqsave+0x40/0x54) r7:00000000 r6:8005a3f8 r5:00000193 r4:be03f6d4 [<806abae0>] (_raw_spin_lock_irqsave) from [<8005a3f8>] (complete+0x1c/0x4c) r6:80950904 r5:be03f6d0 r4:be03f6d4 [<8005a3dc>] (complete) from [<8041b4c0>] (fec_enet_interrupt+0x128/0x164) r6:80950904 r5:00800000 r4:be03f000 r3:00000000 [<8041b398>] (fec_enet_interrupt) from [<8006aeac>] (handle_irq_event_percpu+0x38/0x13c) r6:00000000 r5:be01065c r4:be399e00 r3:8041b398 [<8006ae74>] (handle_irq_event_percpu) from [<8006aff4>] (handle_irq_event+0x44/0x64) r10:be03f000 r9:80989fe0 r8:00000000 r7:00000096 r6:be399e00 r5:be01065c r4:be010600 [<8006afb0>] (handle_irq_event) from [<8006e3e8>] (handle_fasteoi_irq+0xc8/0x1bc) r6:8096e764 r5:be01065c r4:be010600 r3:00000000 [<8006e320>] (handle_fasteoi_irq) from [<8006a63c>] (generic_handle_irq+0x30/0x44) r6:be074010 r5:80945e4c r4:00000096 r3:8006e320 [<8006a60c>] (generic_handle_irq) from [<8000f218>] (handle_IRQ+0x54/0xbc) r4:80950d74 r3:00000180 [<8000f1c4>] (handle_IRQ) from [<800086cc>] (gic_handle_irq+0x30/0x68) r8:be3ab478 r7:c080e100 r6:be075bd8 r5:80950eec r4:c080e10c r3:000000a0 [<8000869c>] (gic_handle_irq) from [<80013064>] (__irq_svc+0x44/0x5c) Signed-off-by:
-
Fugang Duan authored
i.MX6 SX change FEC alignment requirement. i.MX6 SX change internal bus from AHB to AXI. It require RX buffer must be 64 bytes alignment. And remove TX buffer alignment requirement. Signed-off-by:
-
Fugang Duan authored
Add compatible string "fsl,imx6sx-fec" for i.MX6SX. Signed-off-by:
-
Frank Li authored
i.MX6SX Enet-AVB support 3 tx queues, 3 rx queues. For tx queues: ring 0 -> best effort ring 1 -> Class A ring 2 -> Class B For rx queues: ring 0 -> best effort ring 1 -> receive VLAN packet with classification match ring 2 -> receive VLAN packet with classification match Add enet-avb IP multiqueue support for the driver. Signed-off-by:
-
Fugang Duan authored
For i.MX6SX enet use AXI bus, reset MAC will make system bus dead if ENET-AXI bus has pending access (AHB bus should not have such issue). So, disable enet with AVB MAC instead of reset MAC itself. Signed-off-by:
-
Frank Li authored
initilized all queues according to queue number get from DT file. Signed-off-by:
-
Fugang Duan authored
By default, the tx/rx queue number is 1, user can config the queue number at DTS file like this: fsl,num-tx-queues=<3>; fsl,num-rx-queues=<3> Since i.MX6SX enet-AVB IP support multi queues, so use multi queues interface to allocate and set up an Ethernet device. Signed-off-by:
-
Fugang Duan authored
This patch just change data structure to support multi-queue. Only 1 queue enabled. Ethernet multiqueue mechanism can improve performance in SMP system. For single hw queue, multiqueue can balance cpu loading. For multi hw queues, multiple cores can process network packets in parallel, and refer the article for the detail advantage for multiqueue: http://vger.kernel.org/~davem/davem_nyc09.pdfSigned-off-by:
-
Fugang Duan authored
Add enet AVB feature macro define for imx6sx. Signed-off-by:
-
Fugang Duan authored
i.MX6sx enet has below clocks for user config: clk_ipg: ipg_clk_s, ipg_clk_mac0_s, 66Mhz clk_ahb: enet system clock, it is enet AXI clock for imx6sx. For imx6sx, it alos is the clock source of interrupt coalescing. The clock range: 200Mhz ~ 266Mhz. clk_ref: refrence clock for tx and rx. For imx6sx enet RGMII mode, the refrence clock is 125Mhz coming from internal PLL or external. In i.MX6sx-arm2 board, the clock is from internal PLL. clk_ref is optional, depends on board. clk_enet_out: The clock can be output from internal PLL. It can supply 50Mhz clock for phy. clk_enet_out is optional, depends on chip and board. clk_ptp: 1588 ts clock. It is optional, depends on chip. The patch add clk_ref to distiguish the different clocks. Signed-off-by:
-
Andrew Lunn authored
This is the Marvell driver with some cleanups by Claudio Leite and myself. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Cc: Claudio Leite <leitec@staticky.com> Signed-off-by:
Claudio Leite <leitec@staticky.com> Signed-off-by:
-
David S. Miller authored
Sathya Perla says: ==================== be2net: patch set Patch 1 fixes some minor issues with log messages in be2net. Patch 2 replaces strcpy() calls with strlcpy() to avoid possible buffer overflow. Patch 3 improves the RX buffer posting scheme for jumbo frames. Patch 4 replaces the use of v0 of SET_FLOW_CONTROL cmd with v1 to receive a definitive completion status from FW. Patch 5 adds support for ethtool "-m" ethtool option. Patch 6 fixes port-type reporting via ethtool get_settings for QSFP/SFP+ interfaces. Patch 7 fixes the usage of MODIFY_EQD FW cmd to target a max of 8 EQs on Lancer chip. Patch 8 enables PCIe error reporting even for VFs. Pls consider applying this patch set to net-next. Thanks. ==================== Signed-off-by: -
Kalesh AP authored
Currently PCIe error reporting is enabled only on PFs. This patch enables this feature on VFs too as Lancer VFs support it. Signed-off-by:
Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by:
Sathya Perla <sathya.perla@emulex.com> Signed-off-by:
-
Kalesh AP authored
The MODIFY_EQ_DELAY FW cmd on Lancer is supported for a max of 8 EQs per cmd. Signed-off-by:
-
Ravikumar Nelavelli authored
Report the ethtool port-type/supported/advertising values based on the cable_type for QSFP and SFP+ interfaces. The cable_type is parsed from the transceiver data fetched from the FW. Signed-off-by:
Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com> Signed-off-by:
Suresh Reddy <Suresh.Reddy@emulex.com> Signed-off-by:
-
Mark Leonard authored
This patch adds support for the dump-module-eeprom and module-info ethtool options. Signed-off-by:
Mark Leonard <mark.leonard@emulex.com> Signed-off-by:
-
Suresh Reddy authored
In some configurations the FW doesn't allow changing flow control settings of a link. Unless a v1 version of the SET_FLOW_CONTROL cmd is used, the FW doesn't report an error to the driver. Signed-off-by:
-
Ajit Khaparde authored
In the RX path, the driver currently consumes upto 64 (budget) packets in one NAPI sweep. When the size of the packet received is larger than a fragment size (2K), more than one fragment is consumed for each packet. As the driver currently posts a max of 64 fragments, all the consumed fragments may not be replenished. This can cause avoidable drops in RX path. This patch fixes this by posting a max(consumed_frags, 64) frags. This is done only when there are atleast 64 free slots in the RXQ. Signed-off-by:
Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by:
-
Vasundhara Volam authored
Replace strcpy with strlcpy, as it avoids a possible buffer overflow. Signed-off-by:
-
Vasundhara Volam authored
This patch fixes the following minor issues with log messages in be2net: 1) Period is not required at the end of log message. 2) Remove "Unknown grp5 event" logs to reduce noise. The driver can safely ignore async events from FW it's not interested in. 3) Reword a log message for better readability to say that SRIOV "is disabled" rather than "not supported". Signed-off-by:Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by:
-
Hannes Frederic Sowa authored
Currently we have 2 pkt_type_offset functions doing the same thing and spread across the architecture files. Remove those and replace them with a PKT_TYPE_OFFSET macro helper which gets the constant value from a zero sized sk_buff member right in front of the bitfield with offsetof. This new offset marker does not change size of struct sk_buff. Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Markos Chandras <markos.chandras@imgtec.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com> Signed-off-by:
Denis Kirjanov <kda@linux-powerpc.org> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by:
Alexei Starovoitov <ast@plumgrid.com> Acked-by:
Daniel Borkmann <dborkman@redhat.com> Signed-off-by:
-
Florian Fainelli authored
Now that we introduced an additional multiplexing/demultiplexing layer with commit 3e8a72d1 ("net: dsa: reduce number of protocol hooks") that lives within the DSA code, we no longer need to have a given switch driver tag_protocol be an actual ethertype value, instead, we can replace it with an enum: dsa_tag_protocol. Do this replacement in the drivers, which allows us to get rid of the cpu_to_be16()/htons() dance, and remove ETH_P_BRCMTAG since we do not need it anymore. Suggested-by:
Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by:
-
hayeswang authored
Support hw VLAN for tx and rx. And enable them by default. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
Wei Yongjun authored
In case of error, the function devm_ioremap_resource() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
-
WANG Cong authored
If IPv6 is explicitly disabled before the interface comes up, it makes no sense to continue when it comes up, even just print a message. (I am not sure about other cases though, so I prefer not to touch) Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
-
David S. Miller authored
Cong Wang says: ==================== ipv6: clean up locking code in anycast and mcast This patchset cleans up the locking code in anycast.c and mcast.c and makes the refcount code more readable. Signed-off-by:
-
WANG Cong authored
Refactor out allocation and initialization and make the refcount code more readable. Signed-off-by:
-
WANG Cong authored
Signed-off-by:
-
WANG Cong authored
Similarly the code is already protected by rtnl lock. Signed-off-by:
-
WANG Cong authored
Similarly the code is already protected by rtnl lock. Signed-off-by:
-
WANG Cong authored
Refactor out allocation and initialization and make the refcount code more readable. Signed-off-by:
-
WANG Cong authored
Make it accept inet6_dev, and rename it to __ipv6_dev_ac_inc() to reflect this change. Signed-off-by:
-
WANG Cong authored
Just move rtnl lock up, so that the anycast list can be protected by rtnl lock now. Signed-off-by:
-
WANG Cong authored
These code is now protected by rtnl lock, rcu read lock is useless now. Signed-off-by:
-
David S. Miller authored
Nikolay Aleksandrov says: ==================== bonding: get rid of curr_slave_lock This is the second patch-set dealing with bond locking and the purpose here is to convert curr_slave_lock into a spinlock called "mode_lock" which can be used in the various modes for their specific needs. The first three patches cleanup the use of curr_slave_lock and prepare it for the conversion which is done in patch 4 and then the modes that were using their own locks are converted to use the new "mode_lock" giving us the opportunity to remove their locks. This patch-set has been tested in each mode by running enslave/release of slaves in parallel with traffic transmission and miimon=1 i.e. running all the time. In fact this lead to the discovery of a subtle bug related to RCU which will be fixed in -net. Also did an allmodconfig test just in case :-) v2: fix bond_3ad_state_machine_handler's use of mode_lock and curr_slave_lock ==================== Signed-off-by:
-
