- 28 Aug, 2009 5 commits
-
-
Jussi Kivilinna authored
add_wep_key() tries to check if key length is not 5 AND not 13 but uses (key_len != 5 || key_len != 13) instead. Fix this. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Since configure_filter can sleep now, any multicast configuration needed to be postponed to a work struct. This, however, lead to a problem that we could queue the work, stop the device and then afterwards invoke configure_filter which may lead to driver hangs and is a bug. To fix this, we can just cancel the filter work since it's unnecessary to do after stopping the hw. Since there are various places that call drv_stop, and two of them do very similar things, the code for them can be put into a shared function at the same time. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Reported-by: Lennert Buytenhek <buytenh@wantstofly.org> Tested-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Javier Cardona authored
Support for FIF_OTHER_BSS was missing. This patch adds support for this filtering mode which in turn resolves a problem where mesh interfaces would not receive broadcast traffic. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Javier Cardona authored
The mesh config information element has changed significantly since draft 1.08 This patch brings it up to date. Thanks to Sam Leffler and Rui Paulo for identifying this. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Christian Lamparter authored
The patch "mac80211: fix PS-poll response race" somehow broke broadcast buffering in a funny way. During normal operation - stations are awake - the firmware refused to transmit broadcast frames and reported P54_TX_PSM_CANCELLED. But everything worked as soon as one station entered PSM. The reason: The stack sets IEEE80211_TX_CTL_SEND_AFTER_DTIM for outgoing broadcast frames as soon as a station is marked as sleeping. This flag triggers a path which will reroute these frames into p54's "content after beacon" queue, which is designed to cope with the demands for psm. This patch restores the old behavior. IEEE80211_TX_CTL_CLEAR_PS_FILT will once again be used to signalize the firmware to ignore the ps canceling for certain frames. Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 27 Aug, 2009 5 commits
-
-
Ursula Braun authored
If nothing has been written into the qeth sysfs-attribute layer2, its value is "-1" meaning "not yet defined". But the value is displayed as "1" meaning "layer2 selected". The patch changes the reading of this "-1"-value to "-1" to make clear the layer2-attribute has not yet been defined. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Klaus-Dieter Wacker authored
qeth displayed an entry in /proc/service_level even when no valid MCL-string was available (the MCL info is blank). The change is to create an entry in /proc/service_level only when MCL-string is non-zero. Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Klaus-Dieter Wacker authored
Clear separation of cast-type determination (send path) for layer-2 resp. layer-3. Allowing to have inline functions for qeth layer- discipline. Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Frank Blaschka authored
In case the IP address list contains entries (not removed when the device was set offline) this entries should be registered next time the device is brought online. In the past this was done implicitly with the device open call but since we wait in the set IPv4 IPA and the device open common code holds various locks this does not work any longer. Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Klaus-Dieter Wacker authored
Qeth HiperSockets support now retries sending of packets when the IBM System z signals a temporary resource shortage (e.g. target buffer full). The packet is enqueued into the device queue. After 3 times of unsuccessful send the packet is dropped. Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 26 Aug, 2009 21 commits
-
-
David S. Miller authored
Steven Rostedt has suggested that Neil work with the tracing folks, trying to use TRACE_EVENT as the mechanism for implementation. And if that doesn't workout we can investigate other solutions such as that one which was tried here. This reverts the following 2 commits: 5a165657 ("net: skb ftracer - Add config option to enable new ftracer (v3)") 9ec04da7 ("net: skb ftracer - Add actual ftrace code to kernel (v3)") Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
This patch updates the tg3 version to 3.100. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
This brings the 57780's phy into IEEE compliance by suppressing the common mode oscillation. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
This patch adds support for the AC131 fast ethernet transceiver. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
This patch adds support for the BCM50610M phy ID. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
This patch converts the code to use the PHY_IS_FET flag rather than the ASIC revision to decide whether or not to use FET paths. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
Broadcom's phys come in two distinctly different register layouts. For the lack of an official term to distinguish between the two formats, we can loosely categorize them by their fast ethernet or gigabit ethernet transceiver description. This patch creates the (driver-internal) Fast Ethernet Transceiver (FET) namespace and converts the 5906 EPHY definitions over. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
This patch tunes the timeouts the CPMU uses to decide when to switch from the clocks output by the PHY to internal clock sources. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
This patch adds support for the 57788 and removes support for the 57720 which was never released. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
Most older tg3 devices only supported a PCIe maximum payload size of 128 bytes. More recent devices bump this limit up to 256 bytes though. This patch modifies the code so that the MPS limit is only enforced on those devices that only allow the 128 byte setting. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
Julia Lawall discovered that the TG3_FLG2_TSO_CAPABLE flag was being compared against the wrong flags device member. This patch implements the fix. Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
This patch prevents a tx BD corruption bug by preventing the device from powering down the PLL from L1 if the link speed is 10Mbps or 100Mbps. The same bits are also used to prevent a system hang during chip reset resulting from a complicated set of events that ultimately leads to PCIe block register corruption. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Matt Carlson authored
This patch fixes some PCIe link receiver errors by decreasing the internal electrical idle timeout. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Graham, David authored
Remove function e1000_mta_set, as it is no longer called Signed-off-by: Dave Graham <david.graham@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexander Duyck authored
We were already exporting TSO6 to the vlan, but we weren't exporting the checksum support for IPV6 which was causing warning messages to be displayed when doing IPv6 TSO over a vlan. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Don Skidmore authored
We have some ~40 functions that were being called out with 'make namespacecheck'. This patch changes these functions to be static. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Mallikarjuna R Chilakala authored
Fix ethtool get_settings logic to report 10G & 1G advertised and supported link modes in all 8259x 10G backplane connection types except for 82598EB BX network connection type. Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Narender Kumar authored
When the interface is put in bridged mode, destination mac addresses are unknown to firmware. So packets take a slow path (lower priority) in firmware reducing performance. Firmware can cache limited number of remote unicast mac addresses for certain interval, if "dynamic mac learning" mode is enabled. Driver needs to enable this "mac learning" mode in firmware. Currently this is done through net device class sysfs entry, possibly this can also be done upon netlink notifications to from bridge. Signed-off-by: Narender Kumar <narender.kumar@qlogic.com> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dhananjay Phadke authored
Consolidate all MAC/PHY access functions into netxen_nic_hw.c Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dhananjay Phadke authored
Implement common function for locking/unlocking 8 hardware semaphores used for serializing access to shared resouces on a NIC board by different PCI functions. As by definition, callers of these semaphore API can be put to sleep till the semaphore is locked. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dhananjay Phadke authored
Remove code for phy access on unreleased NX2031 based quad-gig board. NX3031 based production quad-gig boards do not require direct phy access by driver. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 24 Aug, 2009 9 commits
-
-
-
Florian Fainelli authored
Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Mark Kelly authored
Instead of fully initializing an unusable second r6040 device, perform the PHY detection earlier and bail out in r6040_init_one when we could not read the PHY identifier. Signed-off-by: Mark Kelly <mark@bifferos.com> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Mark Kelly authored
This patch removes the unused pioaddr variable. Signed-off-by: Mark Kelly <mark@bifferos.com> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andy Grover authored
Now that RDS transports are no longer compiled-in to RDS core, there is now the possibility that they will not be loaded. This adds a helpful suggestion when rds_bind() fails to find a transport. Signed-off-by: Andy Grover <andy.grover@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andy Grover authored
Now that transports can be loaded in arbitrary order, it is important for rds_trans_get_preferred() to look for them in a particular order, instead of walking the list until it finds a transport that works for a given address. Now, each transport registers for a specific transport slot, and these are ordered so that preferred transports come first, and then if they are not loaded, other transports are queried. Signed-off-by: Andy Grover <andy.grover@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andy Grover authored
Enable the building of transports as modules. Also, improve consistency of Kconfig messages in relation to other protocols, and move build dependency on IB from the RDS core code to the rds_rdma module. Signed-off-by: Andy Grover <andy.grover@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andy Grover authored
Now that rdma and tcp transports will be modularized, we need to export a number of functions so they can call them. Signed-off-by: Andy Grover <andy.grover@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andy Grover authored
This code allows RDS to be tunneled over a TCP connection. RDMA operations are disabled when using TCP transport, but this frees RDS from the IB/RDMA stack dependency, and allows it to be used with standard Ethernet adapters, or in a VM. Signed-off-by: Andy Grover <andy.grover@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-