- 06 Jul, 2019 9 commits
-
-
Sascha Hauer authored
The hci UART line discipline sends its characters in a workqueue. Some devices like the Marvell Bluetooth chips need to make sure that all queued characters are sent before switching the baudrate. This adds a function to synchronize with the workqueue. Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org>
-
Greg Kroah-Hartman authored
When calling debugfs functions, there is no need to ever check the return value. The function can work or not, but the code logic should never do something different based on this. Because we don't care if debugfs works or not, this trickles back a bit so we can clean things up by making some functions return void instead of an error value that is never going to fail. Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by:
Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by:
-
Matthias Kaehlcke authored
Firmware download to the WCN3990 often fails with a 'TLV response size mismatch' error: [ 133.064659] Bluetooth: hci0: setting up wcn3990 [ 133.489150] Bluetooth: hci0: QCA controller version 0x02140201 [ 133.495245] Bluetooth: hci0: QCA Downloading qca/crbtfw21.tlv [ 133.507214] Bluetooth: hci0: QCA TLV response size mismatch [ 133.513265] Bluetooth: hci0: QCA Failed to download patch (-84) This is caused by a vendor event that corresponds to an earlier command to change the baudrate. The event is not processed in the context of the baudrate change and is later interpreted as response to the firmware download command (which is also a vendor command), but the driver detects that the event doesn't have the expected amount of associated data. More details: For the WCN3990 the vendor command for a baudrate change isn't sent as synchronous HCI command, because the controller sends the corresponding vendor event with the new baudrate. The event is received and decoded after the baudrate change of the host port. Identify the 'unused' event when it is received and don't add it to the queue of RX frames. Signed-off-by:
Matthias Kaehlcke <mka@chromium.org> Signed-off-by:
-
Balakrishna Godavarthi authored
Latest qualcomm chips are not sending an command complete event for every firmware packet sent to chip. They only respond with a vendor specific event for the last firmware packet. This optimization will decrease the BT ON time. Due to this we are seeing a timeout error message logs on the console during firmware download. Now we are injecting a command complete event once we receive an vendor specific event for the last RAM firmware packet. Signed-off-by:
Balakrishna Godavarthi <bgodavar@codeaurora.org> Tested-by:
-
Fabian Schindlatz authored
Fix some warnings and one error reported by checkpatch.pl: - lines longer than 80 characters are wrapped - empty lines inserted to separate variable declarations from the actual code - line break inserted after if (...) Co-developed-by:
Thomas Röthenbacher <thomas.roethenbacher@fau.de> Signed-off-by:
Fabian Schindlatz <fabian.schindlatz@fau.de> Cc: linux-kernel@i4.cs.fau.de Signed-off-by:
-
Jian-Hong Pan authored
Realtek RTL8822BE BT chip on ASUS X420FA cannot be turned on correctly after on-off several times. Bluetooth daemon sets BT mode failed when this issue happens. Scanning must be active while turning off for this bug to be hit. bluetoothd[1576]: Failed to set mode: Failed (0x03) If BT is turned off, then turned on again, it works correctly again. According to the vendor driver, the HCI_QUIRK_RESET_ON_CLOSE flag is set during probing. So, this patch makes Realtek's BT reset on close to fix this issue. Link: https://bugzilla.kernel.org/show_bug.cgi?id=203429Signed-off-by:
Jian-Hong Pan <jian-hong@endlessm.com> Reviewed-by:
Daniel Drake <drake@endlessm.com> Signed-off-by:
-
Fabian Schindlatz authored
Extract the new function send_command_from_firmware from download_firmware, which helps with the readability of the switch statement. This way the code is less deeply nested and also no longer exceeds the 80 character limit. Co-developed-by:
-
Philipp Puschmann authored
Uploading the firmware needs quite a few seconds if done at 115200 kbps. So set the operational frequency, usually 3 MHz, before uploading the firmware. I have successfully tested this with a wl1837mod. Signed-off-by:
Philipp Puschmann <philipp.puschmann@emlix.com> Signed-off-by:
-
Peter Robinson authored
BCM4356 devices soldered onto the PCB (non-removable) use an UART connection for bluetooth, such as the Rock960, but it also advertise btsdio support as a sdio function. Signed-off-by:
Peter Robinson <pbrobinson@gmail.com> CC: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by:
-
- 05 Jul, 2019 31 commits
-
-
David S. Miller authored
Tariq Toukan says: ==================== mlx5 TLS TX HW offload support This series from Eran and me, adds TLS TX HW offload support to the mlx5 driver. This offloads the kTLS encryption process from kernel to the Mellanox NIC, saving CPU cycles and improving utilization. Upon a new TLS connection request, driver is responsible to create a dedicated HW context and configure it according to the crypto info, so HW can do the encryption itself. When the HW context gets out-of-sync (i.e. due to packets retransmission), driver is responsible for the re-sync process. This is done by posting special resync descriptors to the HW. Feature is supported on Mellanox Connect-X 6DX, and newer. Series was tested on SimX simulator. Series generated against net-next commit [1], with Saeed's request pulled [2]: [1] c4cde580 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next [2] git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux.git tags/mlx5-updates-2019-07-04-v2 Changes from last pull request: Fixed comments from Jakub: Patch 4: - Replace zero memset with a call to memzero_explicit(). Patch 11: - Fix stats counters names. - Drop TLS SKB with non-matching netdev. ==================== Acked-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Tariq Toukan authored
Add support for transmit side kernel-TLS acceleration. Offload the crypto encryption to HW. Per TLS connection: - Use a separate TIS to maintain the HW context. - Use a separate encryption key. - Maintain static and progress HW contexts by posting the proper WQEs at creation time, or upon resync. - Use a special DUMP opcode to replay the previous frags and sync the HW context. To make sure the SQ is able to serve an xmit request, increase SQ stop room to cover: - static params WQE, - progress params WQE, and - resync DUMP per frag. Currently supporting TLS 1.2, and key size 128bit. Tested over SimX simulator. Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Tariq Toukan authored
Similar to the existing mlx5e_post_nop(), but marks a fence in the WQE control segment. Added as a separate new function to not hurt the performance of the common case. To be used in a downstream patch of the series. Signed-off-by:
Boris Pismenny <borisp@mellanox.com> Signed-off-by:
-
Tariq Toukan authored
Let the EN TIS creation function (mlx5e_create_tis) be responsible for applying common mdev related fields. Other specific fields must be set by the caller and passed within the inbox. Signed-off-by:
-
Tariq Toukan authored
Use an SQ field for stop_room, and use the larger value only if TLS is supported. Signed-off-by:
-
Eran Ben Elisha authored
When polling a CQE of an SKB-less WQE, don't assume it consumed only one WQEBB. Use wi->num_wqebbs directly instead. In the downstream patch, SKB-less WQEs might have more the one WQEBB, thus this change is needed. Signed-off-by:
-
Tariq Toukan authored
Change mlx5e_sq_fetch_wqe to be agnostic to the Work Queue Element (WQE) type. Before this patch, it was specific for struct mlx5e_tx_wqe. In order to allow the change, the function now returns the generic void pointer, and gets the WQE size to do the zero memset. Signed-off-by:
-
Tariq Toukan authored
When ctrl->tisn field exists, this indicates an operation (HW offload) on the TCP payload. For such WQEs, inline the headers up to L4. This is in preparation for kTLS HW offload support, added in a downstream patch. Signed-off-by:
-
Tariq Toukan authored
Take datapath helper functions to a new header file en/txrx.h. Signed-off-by:
-
Tariq Toukan authored
Add support for the new TLS implementation of the Connect-X family. Introduce a new compilation flag MLX5_TLS for it. Signed-off-by:
-
Tariq Toukan authored
Encryption key create / destroy is done via CREATE_GENERAL_OBJECT / DESTROY_GENERAL_OBJECT commands. To be used in downstream patches by TLS API wrappers, to configure the TIS context with the encryption key. Signed-off-by:
-
Tariq Toukan authored
Always contain all acceleration functions declarations in 'accel' files, independent to the flags setting. For this, introduce new flags CONFIG_FPGA_{IPSEC/TLS} and use stubs where needed. This obsoletes the need for stubs in 'fpga' files. Remove them. Also use the new flags in Makefile, to decide whether to compile TLS-specific or IPSEC-specific objects, or not. Signed-off-by: -
Tariq Toukan authored
Do not directly call fpga version of IPsec function from main.c. Wrap it by an accel version, and call the wrapper. This will allow deprecating the FPGA IPsec stubs in downstream patch. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5-update-2019-07-04 This series adds mlx5 support for devlink fw versions query. 1) Implement the required low level firmware commands 2) Implement the devlink knobs and callbacks for fw versions query. ==================== Signed-off-by: -
Sebastian Andrzej Siewior authored
For spinlocks the type spinlock_t should be used instead of "struct spinlock". Use spinlock_t for spinlock's definition. Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: oss-drivers@netronome.com Cc: netdev@vger.kernel.org Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by:
-
Ilias Apalodimas authored
Quoting Arnd, We have to do a sync_single_for_device /somewhere/ before the buffer is given to the device. On a non-cache-coherent machine with a write-back cache, there may be dirty cache lines that get written back after the device DMA's data into it (e.g. from a previous memset from before the buffer got freed), so you absolutely need to flush any dirty cache lines on it first. Since the coherency is configurable in this device make sure we cover all configurations by explicitly syncing the allocated buffer for the device before refilling it's descriptors Signed-off-by:
Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by:
-
David S. Miller authored
Huazhong Tan says: ==================== net: hns3: some cleanups & bugfixes This patch-set includes cleanups and bugfixes for the HNS3 ethernet controller driver. [patch 1/9] fixes VF's broadcast promisc mode not enabled after initializing. [patch 2/9] adds hints for fibre port not support flow control. [patch 3/9] fixes a port capbility updating issue. [patch 4/9 - 9/9] adds some cleanups for HNS3 driver. ==================== Signed-off-by: -
Peng Li authored
If HCLGE_MBX_MAX_RESP_DATA_SIZE > HCLGE_MBX_MAX_RESP_DATA_SIZE, the memcpy will cause out of memory. So this patch just set resp_data_len to the maximum length for this case. Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
Yonglong Liu authored
There are some bitwise operator used signed type, this patch fixes them with unsigned type. Signed-off-by:
Yonglong Liu <liuyonglong@huawei.com> Signed-off-by:
-
Peng Li authored
This patch adds default value for tc_size and tc_offset, or it may get random value and used later. Signed-off-by:
-
Weihang Li authored
The value of msg_data may be NULL in some cases, which will cause errors reported by some compiler. So this patch adds a check to fix it. Signed-off-by:
Weihang Li <liweihang@hisilicon.com> Signed-off-by:
-
Peng Li authored
The value of param type is always not changed in hclgevf_bind_ring_to_vector, move the assignment to front of "for {}" can reduce the redundant assignment. Signed-off-by: -
Peng Li authored
Currently, the HNS3 driver just defines part of IMP return code, This patch supplements all the remaining IMP return code, and adds a function to convert this code to the error number. Signed-off-by:
-
Jian Shen authored
Currently, the driver queries the media port information, and updates the port capability periodically. But it sets an error mac->speed_type value, which stops update port capability. Fixes: 88d10bd6 ("net: hns3: add support for multiple media type") Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
-
Jian Shen authored
Flow control autoneg is unsupported for fibre port. It takes no effect for flow control when restart autoneg. This patch fixes it, return -EOPNOTSUPP when user tries to enable flow control autoneg. Signed-off-by:
-
Jian Shen authored
For revision 0x20, the broadcast promisc is enabled by firmware, it's unnecessary to enable it when initializing VF. For revision 0x21, it's necessary to enable broadcast promisc mode when initializing or re-initializing VF, otherwise, it will be unable to send and receive promisc packets. Fixes: f01f5559 ("net: hns3: don't allow vf to enable promisc mode") Signed-off-by:
-
Li RongQing authored
the check parameter is never used Signed-off-by:
Li RongQing <lirongqing@baidu.com> Signed-off-by:
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw: Enable/disable PTP shapers Shalom says: In order to get more accurate hardware time stamping in Spectrum-1, the driver needs to apply a shaper on the port for speeds lower than 40Gbps. This shaper is called a PTP shaper and it is applied on hierarchy 0, which is the port hierarchy. This shaper may affect the shaper rates of all hierarchies. This patchset adds the ability to enable or disable the PTP shaper on the port in two scenarios: 1. When the user wants to enable/disable the hardware time stamping 2. When the port is brought up or down (including port speed change) Patch #1 adds the QEEC.ptps field that is used for enabling or disabling the PTP shaper on a port. Patch #2 adds a note about disabling the PTP shaper when calling to mlxsw_sp_port_ets_maxrate_set(). Patch #3 adds the QPSC register that is responsible for configuring the PTP shaper parameters per speed. Patch #4 sets the PTP shaper parameters during the ptp_init(). Patch #5 adds new operation for getting the port's speed. Patch #6 enables/disables the PTP shaper when turning on or off the hardware time stamping. Patch #7 enables/disables the PTP shaper when the port's status has changed (including port speed change). Patch #8 applies the PTP shaper enable/disable logic by filling the PTP shaper parameters array. ==================== Signed-off-by: -
Shalom Toledo authored
Apply by filling the PTP shaper parameters array. Signed-off-by:
Shalom Toledo <shalomt@mellanox.com> Reviewed-by:
Petr Machata <petrm@mellanox.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Shalom Toledo authored
When getting port up down event (PUDE), change the PTP shaper configuration based on hardware time stamping on/off and the port's speed. Signed-off-by:
-
Shalom Toledo authored
In order to get more accurate hardware time stamping, the driver needs to enable PTP shaper on the port, for speeds lower than 40 Gbps. Enable the PTP shaper on the port when the user turns on the hardware time stamping, and disable it when the user turns off the hardware time stamping. Signed-off-by:
-
