- 29 Jan, 2015 24 commits
-
-
Arend van Spriel authored
The nvram file can hold a key=value combination in which the value may have spaces, ie. 'RAW1=80 02 fe ff'. The parsing functionality did not deal with this so it gives an error message: [621746.311635] brcmfmac: brcmf_nvram_handle_key warning: ln=90:col=11: '=' expected, skip invalid key entry because RAW1=80 is being considerd as key=value pair and it expects '=' sign after '02' for next key=value pair. This entry can be completely ignored as firmware does not need it. Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by:
Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Arend van Spriel authored
When revinfo retrieval fails we can not show the firmware version in ethtool driver info. Store the result to be used when handling ethtool driver info callback. Reviewed-by:
-
Arend van Spriel authored
The ethtool driver info already contained the unique firmware identifier. This patch adds the firmware release version. $ ethtool -i wlan4 driver: brcmfmac version: 6.10.224.22 firmware-version: 01-32bd010f Reviewed-by:
-
Arend van Spriel authored
Obtain device revision information and store it. Reviewed-by:
-
Arend van Spriel authored
In some scenarios the chip number and revision may not be provided by the bus layer. If the chip number is not filled, the common layer will ask the firmware for this information. Reviewed-by:
-
Arend van Spriel authored
Introducing a define that the caller of brcmu_boardrev_str() can use to allocate enough room for buffer passed to the function. Reviewed-by:
-
Arend van Spriel authored
In brcmf_usb_probe_cb() the device is checked to determine whether it is already running firmware. However, when no firmware download is needed it still continues to request the firmware files. This is fixed by returning after successful setup. Reviewed-by:
-
Hante Meuleman authored
During suspend the bus state is put in the down state. When data is being transmitted during this state then the netdev queue will be close. This patch will wake the queue on state data if the queue was closed. Reviewed-by:
-
Hante Meuleman authored
Each bus driver is maintaing an exported bus state indicating if upper layers can or cannot send data. SDIO is using this state also for more private states. This makes handling the states and state changes complex. This patch minimises the exposed states and makes SDIO keep track of an internal state where necessary. Reviewed-by:
-
Arend van Spriel authored
Before going in suspend state the watchdog thread needs to put the device in bus sleep state, which assures it can go in deep-sleep state during D3 state. Reviewed-by:
-
Arend van Spriel authored
The driver always called cfg80211_disconnected() with reason parameter set to zero, ie. unknown. However, firmware does provide a valid 802.11 reason code in DEAUTH and DISASSOC event message to the driver. This patch passes the reason code to cfg80211_disconnected(). Reviewed-by:
-
Hante Meuleman authored
Control frames are normally handled outside DPC, but sometimes within DPC. To simplify code always handle control within DPC. Reviewed-by:
-
Hante Meuleman authored
When the system is resumed a deadlock can occur when DPC gets entered before resume is complete. This patch fixes this by properly checking the suspend state outside the claim_host code block. Reviewed-by:
-
Hante Meuleman authored
On every tx the flow worker is triggered. When running high throughput data this causes an excessive amount of times the worker gets activated. This patch starts scheduling the worker more relaxed once outstanding tx has reached a certain depth. Reviewed-by:
-
Vladimir Kondratiev authored
This fixes issue reported by Dan Carpenter: The patch 3277213f: "wil6210: ADDBA/DELBA flows" from Dec 23, 2014, leads to the following static checker warning: drivers/net/wireless/ath/wil6210/rx_reorder.c:205 wil_tid_ampdu_rx_alloc() error: scheduling with locks held: 'spin_lock:tid_rx_lock' drivers/net/wireless/ath/wil6210/rx_reorder.c 202 struct wil_tid_ampdu_rx *wil_tid_ampdu_rx_alloc(struct wil6210_priv *wil, 203 int size, u16 ssn) 204 { 205 struct wil_tid_ampdu_rx *r = kzalloc(sizeof(*r), GFP_KERNEL); ^^^^^^^^^^ 206 207 if (!r) 208 return NULL; 209 210 r->reorder_buf = 211 kcalloc(size, sizeof(struct sk_buff *), GFP_KERNEL); ^^^^^^^^^^^ 212 r->reorder_time = 213 kcalloc(size, sizeof(unsigned long), GFP_KERNEL); ^^^^^^^^^^^ 214 if (!r->reorder_buf || !r->reorder_time) { 215 kfree(r->reorder_buf); 216 kfree(r->reorder_time); 217 kfree(r); 218 return NULL; 219 } 220 [ snip ] 331 spin_lock_bh(&sta->tid_rx_lock); ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ spin lock held. 332 333 wil_tid_ampdu_rx_free(wil, sta->tid_rx[tid]); 334 sta->tid_rx[tid] = wil_tid_ampdu_rx_alloc(wil, agg_wsize, ssn); ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ function called with the lock held. 335 336 spin_unlock_bh(&sta->tid_rx_lock); Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by:
-
Vladimir Kondratiev authored
Access point require this API to check peer alive status. Assume peer is alive when it is connected, because firmware implements keep alive checks and will disconnect peer if it is not alive. Signed-off-by:
-
Vladimir Kondratiev authored
Implement Tx status reporting using skb_complete_wifi_ack(). Signed-off-by:
-
Vladimir Shulman authored
Interrupt moderation parameters will never be passed as module parameters. For product, they will be hard-coded after lab testing, and for debugging, they can be altered via debugfs. Signed-off-by:
Vladimir Shulman <qca_shulmanv@qca.qualcomm.com> Signed-off-by:
-
Vladimir Shulman authored
Due to HW limitation, inter-packet gap timeout max value is 13 usec. Update of current thresholds from 15 to 13 usec. Signed-off-by:
-
Vladimir Shulman authored
Tuning rings size for performance optimization. Increasing Tx ring size, allows buffering more packets for HW, thus eliminating idle periods which were observed with smaller ring at high throughput, because HW was fetching packets faster than driver was filling them into the TX ring. Rx ring was similarly increased to avoid same problems in Rx. Signed-off-by:
-
Vladimir Shulman authored
Tx queue was hard-coded to 1000 in ether_setup. Add wil_dev_setup function which configures tx queue len to chosen default value after calling ether_setup. Signed-off-by:
-
Dedy Lansky authored
upon cfg80211_stop_ap, a graceful AP shutdown is requested from firmware followed by firmware reset. In case graceful request failed, error was returned to cfg80211. The change is to return success in this scenario, because firmware reset will anyhow shutdown the AP. Signed-off-by:
Dedy Lansky <qca_dlansky@qca.qualcomm.com> Signed-off-by:
-
Dedy Lansky authored
netif_carrier_on indication was too late. In case Rx packet received before netif_carrier_on indication, upper layers could not send Tx packet back. The fix is to indicate netif_carrier_on earlier: for STA, indicate netif_carrier_on when association starts. for AP/PCP, indicate netif_carrier_on upon starting AP/PCP. Signed-off-by:
-
Vladimir Kondratiev authored
Incorporate changes from firmware. Signed-off-by:
-
- 27 Jan, 2015 8 commits
-
-
Taehee Yoo authored
After rtl8192cu download firmware routine, set fw_ready flag. Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Avinash Patil authored
Some devices do not support extended scan. This patch adds support to enble ext_scan selectively. For SD/PCIe interfaces, deefine ext_scan_support as part of card structure and use it to initialize ext_scan in adapter during registering device. For USB interfaces, we initialize ext_scan during register_dev handler. Signed-off-by:
Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
-
Yogesh Ashok Powar authored
USB8801 is Marvell's 1x1 802.11bgn offering. Patch adds Device IDs support and defines TX buffer size. Signed-off-by:
Nishant Sarmukadam <nishants@marvell.com> Signed-off-by:
Cathy Luo <cluo@marvell.com> Signed-off-by:
Frank Huang <frankh@marvell.com> Signed-off-by:
-
Yogesh Ashok Powar authored
SD8801 is Marvell's 1x1 802.11bgn offering. This patch adds Device IDs for SD8801 and also defines card structure which has definition for register offsets, buffer sizes etc. Signed-off-by:
James Cameron <quozl@laptop.org> Signed-off-by:
-
Hong Xu authored
ath9k and ath9k_htc use the variable name "led_blink" to indicate whether the module parameter "blink" is on. This name is easy to conflict with other variables, and has caused a compiler error found by kbuild test bot. The compiler error is as following: drivers/net/wireless/ath/ath9k/ath9k_htc.o:(.data+0x47c): multiple definition of `led_blink' drivers/net/wireless/ath/ath9k/ath9k.o:(.bss+0x20): first defined here Fixes: 3a939a67 ("ath9k_htc: Add a module parameter to disable blink") Reported-by:
kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
Hong Xu <hong@topbug.net> Signed-off-by:
-
Chun-Yeow Yeoh authored
Patch "rtlwifi: add support to send beacon frame" allows the beaconing of rtl8192cu. But mesh beaconing is not working. Fix this. Signed-off-by:
Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Acked-by:
-
Taehee Yoo authored
In AP mode, beacon frame is necessary to keep connection. this patch adds a sending beacon frame routine in initialization routine. Signed-off-by:
-
Johannes Berg authored
This patch adds fix to set carrier state off during ndo_open. Carrier should be set to ON when device is ready to send data. In case of station/adhoc interface device is able to transfer data after successful association/join operation. For AP this would be after bss_active event. Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
- 23 Jan, 2015 8 commits
-
-
Rafał Miłecki authored
Starting with kernel 3.19-rc1 early registration of bcma on MIPS is done a bit later, with memory allocator available. This allows us to simplify code by using standard bus scanning method. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Rasmus Villemoes authored
The kernel's string library does in fact have strcasecmp, at least since ded220bd ("[STRING]: Move strcasecmp/strncasecmp to lib/string.c"). Moreover, this open-coded version is in fact wrong: If the strings only differ in their last character, a and b have already been incremented to point to the terminating NUL bytes, so they would wrongly be treated as equal. Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
-
Nicholas Mc Guire authored
if(!wait_for_completion_interruptible_timeout(...)) only handles the timeout case - this patch adds handling the signal case the same as timeout. Signed-off-by:
Nicholas Mc Guire <der.herr@hofr.at> Acked-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
-
Nicholas Mc Guire authored
if(!wait_for_completion_interruptible_timeout(...)) only handles the timeout case - this patch adds handling the signal case the same as timeout. Signed-off-by:
-
John Linville authored
Coverity: CID 114932 Signed-off-by:
John W. Linville <linville@tuxdriver.com> Acked-by:
Nick Kossifidis <mickflemm@gmail.com> Signed-off-by:
-
John Linville authored
This clause is conditioned on htc_hdr != NULL, but it will only be NULL when that check is reached. Coverity: CID 114318 Signed-off-by:
-
Vaishali Thakkar authored
This patch introduces the use of function put_unaligned_le32. This is done using Coccinelle and semantic patch used is as follows: @A@ typedef u32, __le32, uint32_t; {u32,__le32,uint32_t} e32; identifier tmp; expression ptr; expression y,e; type T; type T; @@ - tmp = cpu_to_le32(y); <+... when != tmp ( - memcpy(ptr, (T)&tmp, \(4\|sizeof(u32)\|sizeof(__le32)\|sizeof(uint32_t)\|sizeof(e32)\)); + put_unaligned_le32(y,ptr); | - memcpy(ptr, (T)&tmp, ...); + put_unaligned_le32(y,ptr); ) ...+> ? tmp = e @@ type T; identifier a.tmp; @@ - T tmp; ...when != tmp Signed-off-by:
Vaishali Thakkar <vthakkar1994@gmail.com> Signed-off-by:
-
Rafał Miłecki authored
This moves main bus init code to the main.c and renames old function to make its purpose clear. Thanks to this change we'll also be able to separate scanning from registration (and support PCIe Gen 2 devices) in the future. Signed-off-by:
-
