Skip to content

GitLab

Switch branch/tag
  1. 04 Aug, 2019 2 commits
    • csonsino's avatar
      Bluetooth: validate BLE connection interval updates · 427d80d8
      csonsino authored 
      [ Upstream commit c49a8682

 ]

Problem: The Linux Bluetooth stack yields complete control over the BLE
connection interval to the remote device.

The Linux Bluetooth stack provides access to the BLE connection interval
min and max values through /sys/kernel/debug/bluetooth/hci0/
conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval.
These values are used for initial BLE connections, but the remote device
has the ability to request a connection parameter update. In the event
that the remote side requests to change the connection interval, the Linux
kernel currently only validates that the desired value is within the
acceptable range in the Bluetooth specification (6 - 3200, corresponding to
7.5ms - 4000ms). There is currently no validation that the desired value
requested by the remote device is within the min/max limits specified in
the conn_min_interval/conn_max_interval configurations. This essentially
leads to Linux yielding complete control over the connection interval to
the remote device.

The proposed patch adds a verification step to the connection parameter
update mechanism, ensuring that the desired value is within the min/max
bounds of the current connection. If the desired value is outside of the
current connection min/max values, then the connection parameter update
request is rejected and the negative response is returned to the remote
device. Recall that the initial connection is established using the local
conn_min_interval/conn_max_interval values, so this allows the Linux
administrator to retain control over the BLE connection interval.

The one downside that I see is that the current default Linux values for
conn_min_interval and conn_max_interval typically correspond to 30ms and
50ms respectively. If this change were accepted, then it is feasible that
some devices would no longer be able to negotiate to their desired
connection interval values. This might be remedied by setting the default
Linux conn_min_interval and conn_max_interval values to the widest
supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same
behavior as the current implementation, where the remote device could
request to change the connection interval value to any value that is
permitted by the Bluetooth specification, and Linux would accept the
desired value.
Signed-off-by: default avatarCarey Sonsino <csonsino@gmail.com>
Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: default avatarSasha Levin <sashal@kernel.org>
      427d80d8
    • Matias Karhumaa's avatar
      Bluetooth: Check state in l2cap_disconnect_rsp · 0a5e8c13
      Matias Karhumaa authored 
      [ Upstream commit 28261da8

 ]

Because of both sides doing L2CAP disconnection at the same time, it
was possible to receive L2CAP Disconnection Response with CID that was
already freed. That caused problems if CID was already reused and L2CAP
Connection Request with same CID was sent out. Before this patch kernel
deleted channel context regardless of the state of the channel.

Example where leftover Disconnection Response (frame #402) causes local
device to delete L2CAP channel which was not yet connected. This in
turn confuses remote device's stack because same CID is re-used without
properly disconnecting.

Btmon capture before patch:
** snip **
> ACL Data RX: Handle 43 flags 0x02 dlen 8                #394 [hci1] 10.748949
      Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
      RFCOMM: Disconnect (DISC) (0x43)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x53 poll/final 1
         Length: 0
         FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8                #395 [hci1] 10.749062
      Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
      RFCOMM: Unnumbered Ack (UA) (0x63)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x73 poll/final 1
         Length: 0
         FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #396 [hci1] 10.749073
      L2CAP: Disconnection Request (0x06) ident 17 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Packets (0x13) plen 5    #397 [hci1] 10.752391
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5    #398 [hci1] 10.753394
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #399 [hci1] 10.756499
      L2CAP: Disconnection Request (0x06) ident 26 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #400 [hci1] 10.756548
      L2CAP: Disconnection Response (0x07) ident 26 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #401 [hci1] 10.757459
      L2CAP: Connection Request (0x02) ident 18 len 4
        PSM: 1 (0x0001)
        Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #402 [hci1] 10.759148
      L2CAP: Disconnection Response (0x07) ident 17 len 4
        Destination CID: 65
        Source CID: 65
= bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o..   10.759447
> HCI Event: Number of Completed Packets (0x13) plen 5    #403 [hci1] 10.759386
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #404 [hci1] 10.760397
      L2CAP: Connection Request (0x02) ident 27 len 4
        PSM: 3 (0x0003)
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16               #405 [hci1] 10.760441
      L2CAP: Connection Response (0x03) ident 27 len 8
        Destination CID: 65
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27               #406 [hci1] 10.760449
      L2CAP: Configure Request (0x04) ident 19 len 19
        Destination CID: 65
        Flags: 0x0000
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 1013
        Option: Retransmission and Flow Control (0x04) [mandatory]
          Mode: Basic (0x00)
          TX window size: 0
          Max transmit: 0
          Retransmission timeout: 0
          Monitor timeout: 0
          Maximum PDU size: 0
> HCI Event: Number of Completed Packets (0x13) plen 5    #407 [hci1] 10.761399
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 16               #408 [hci1] 10.762942
      L2CAP: Connection Response (0x03) ident 18 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
*snip*

Similar case after the patch:
*snip*
> ACL Data RX: Handle 43 flags 0x02 dlen 8            #22702 [hci0] 1664.411056
      Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
      RFCOMM: Disconnect (DISC) (0x43)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x53 poll/final 1
         Length: 0
         FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8            #22703 [hci0] 1664.411136
      Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
      RFCOMM: Unnumbered Ack (UA) (0x63)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x73 poll/final 1
         Length: 0
         FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22704 [hci0] 1664.411143
      L2CAP: Disconnection Request (0x06) ident 11 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22705 [hci0] 1664.414009
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22706 [hci0] 1664.415007
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22707 [hci0] 1664.418674
      L2CAP: Disconnection Request (0x06) ident 17 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22708 [hci0] 1664.418762
      L2CAP: Disconnection Response (0x07) ident 17 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22709 [hci0] 1664.421073
      L2CAP: Connection Request (0x02) ident 12 len 4
        PSM: 1 (0x0001)
        Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22710 [hci0] 1664.421371
      L2CAP: Disconnection Response (0x07) ident 11 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22711 [hci0] 1664.424082
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22712 [hci0] 1664.425040
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22713 [hci0] 1664.426103
      L2CAP: Connection Request (0x02) ident 18 len 4
        PSM: 3 (0x0003)
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16           #22714 [hci0] 1664.426186
      L2CAP: Connection Response (0x03) ident 18 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27           #22715 [hci0] 1664.426196
      L2CAP: Configure Request (0x04) ident 13 len 19
        Destination CID: 65
        Flags: 0x0000
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 1013
        Option: Retransmission and Flow Control (0x04) [mandatory]
          Mode: Basic (0x00)
          TX window size: 0
          Max transmit: 0
          Retransmission timeout: 0
          Monitor timeout: 0
          Maximum PDU size: 0
> ACL Data RX: Handle 43 flags 0x02 dlen 16           #22716 [hci0] 1664.428804
      L2CAP: Connection Response (0x03) ident 12 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
*snip*

Fix is to check that channel is in state BT_DISCONN before deleting the
channel.

This bug was found while fuzzing Bluez's OBEX implementation using
Synopsys Defensics.
Reported-by: default avatarMatti Kamunen <matti.kamunen@synopsys.com>
Reported-by: default avatarAri Timonen <ari.timonen@synopsys.com>
Signed-off-by: default avatarMatias Karhumaa <matias.karhumaa@gmail.com>
Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: default avatarSasha Levin <sashal@kernel.org>
      0a5e8c13
  3. 10 Jul, 2019 2 commits
  5. 03 Apr, 2019 2 commits
    • Marcel Holtmann's avatar
      Bluetooth: Verify that l2cap_get_conf_opt provides large enough buffer · 99665dcf
      Marcel Holtmann authored 
      commit 7c9cbd0b

 upstream.

The function l2cap_get_conf_opt will return L2CAP_CONF_OPT_SIZE + opt->len
as length value. The opt->len however is in control over the remote user
and can be used by an attacker to gain access beyond the bounds of the
actual packet.

To prevent any potential leak of heap memory, it is enough to check that
the resulting len calculation after calling l2cap_get_conf_opt is not
below zero. A well formed packet will always return >= 0 here and will
end with the length value being zero after the last option has been
parsed. In case of malformed packets messing with the opt->len field the
length value will become negative. If that is the case, then just abort
and ignore the option.

In case an attacker uses a too short opt->len value, then garbage will
be parsed, but that is protected by the unknown option handling and also
the option parameter size checks.
Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
Reviewed-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: default avatarJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      99665dcf
    • Marcel Holtmann's avatar
      Bluetooth: Check L2CAP option sizes returned from l2cap_get_conf_opt · def5c1fb
      Marcel Holtmann authored 
      commit af3d5d1c

 upstream.

When doing option parsing for standard type values of 1, 2 or 4 octets,
the value is converted directly into a variable instead of a pointer. To
avoid being tricked into being a pointer, check that for these option
types that sizes actually match. In L2CAP every option is fixed size and
thus it is prudent anyway to ensure that the remote side sends us the
right option size along with option paramters.

If the option size is not matching the option type, then that option is
silently ignored. It is a protocol violation and instead of trying to
give the remote attacker any further hints just pretend that option is
not present and proceed with the default values. Implementation
following the specification and its qualification procedures will always
use the correct size and thus not being impacted here.

To keep the code readable and consistent accross all options, a few
cosmetic changes were also required.
Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
Reviewed-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: default avatarJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      def5c1fb
  7. 20 Apr, 2018 1 commit
    • Szymon Janc's avatar
      Bluetooth: Fix connection if directed advertising and privacy is used · b0a2a2b2
      Szymon Janc authored 
      commit 082f2300 upstream.

Local random address needs to be updated before creating connection if
RPA from LE Direct Advertising Report was resolved in host. Otherwise
remote device might ignore connection request due to address mismatch.

This was affecting following qualification test cases:
GAP/CONN/SCEP/BV-03-C, GAP/CONN/GCEP/BV-05-C, GAP/CONN/DCEP/BV-05-C

Before patch:
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6          #11350 [hci0] 84680.231216
        Address: 56:BC:E8:24:11:68 (Resolvable)
          Identity type: Random (0x01)
          Identity: F2:F1:06:3D:9C:42 (Static)
> HCI Event: Command Complete (0x0e) plen 4                        #11351 [hci0] 84680.246022
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7         #11352 [hci0] 84680.246417
        Type: Passive (0x00)
        Interva...
      b0a2a2b2
  9. 17 Jan, 2018 1 commit
    • Ben Seri's avatar
      Bluetooth: Prevent stack info leak from the EFS element. · 6aebc267
      Ben Seri authored 
      commit 06e7e776

 upstream.

In the function l2cap_parse_conf_rsp and in the function
l2cap_parse_conf_req the following variable is declared without
initialization:

struct l2cap_conf_efs efs;

In addition, when parsing input configuration parameters in both of
these functions, the switch case for handling EFS elements may skip the
memcpy call that will write to the efs variable:

...
case L2CAP_CONF_EFS:
if (olen == sizeof(efs))
memcpy(&efs, (void *)val, olen);
...

The olen in the above if is attacker controlled, and regardless of that
if, in both of these functions the efs variable would eventually be
added to the outgoing configuration request that is being built:

l2cap_add_conf_opt(&ptr, L2CAP_CONF_EFS, sizeof(efs), (unsigned long) &efs);

So by sending a configuration request, or response, that contains an
L2CAP_CONF_EFS element, but with an element length that is not
sizeof(efs) - the memcpy to the uninitialized efs variable can be
avoided, and the uninitialized variable would be returned to the
attacker (16 bytes).

This issue has been assigned CVE-2017-1000410

Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Signed-off-by: default avatarBen Seri <ben@armis.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      6aebc267
  11. 13 Sep, 2017 1 commit
  13. 22 Nov, 2016 1 commit
  15. 24 Aug, 2016 1 commit
    • Daniel Borkmann's avatar
      Bluetooth: split sk_filter in l2cap_sock_recv_cb · dbb50887
      Daniel Borkmann authored 
      During an audit for sk_filter(), we found that rx_busy_skb handling
in l2cap_sock_recv_cb() and l2cap_sock_recvmsg() looks not quite as
intended.

The assumption from commit e328140f ("Bluetooth: Use event-driven
approach for handling ERTM receive buffer") is that errors returned
from sock_queue_rcv_skb() are due to receive buffer shortage. However,
nothing should prevent doing a setsockopt() with SO_ATTACH_FILTER on
the socket, that could drop some of the incoming skbs when handled in
sock_queue_rcv_skb().

In that case sock_queue_rcv_skb() will return with -EPERM, propagated
from sk_filter() and if in L2CAP_MODE_ERTM mode, wrong assumption was
that we failed due to receive buffer being full. From that point onwards,
due to the to-be-dropped skb being held in rx_busy_skb, we cannot make
any forward progress as rx_busy_skb is never cleared from l2cap_sock_recvmsg(),
due to the filter drop verdict over and over coming from sk_filter().
Meanwhile, in l2cap_sock_recv_cb() all new incoming skbs are being
dropped due to rx_busy_skb being occupied.

Instead, just use __sock_queue_rcv_skb() where an error really tells that
there's a receive buffer issue. Split the sk_filter() and enable it for
non-segmented modes at queuing time since at this point in time the skb has
already been through the ERTM state machine and it has been acked, so dropping
is not allowed. Instead, for ERTM and streaming mode, call sk_filter() in
l2cap_data_rcv() so the packet can be dropped before the state machine sees it.

Fixes: e328140f

 ("Bluetooth: Use event-driven approach for handling ERTM receive buffer")
Signed-off-by: default avatarDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: default avatarMat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: default avatarWillem de Bruijn <willemb@google.com>
Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
      dbb50887
  17. 09 Jul, 2016 1 commit
    • Marcel Holtmann's avatar
      Bluetooth: Rename HCI_BREDR into HCI_PRIMARY · ca8bee5d
      Marcel Holtmann authored 
      
The HCI_BREDR naming is confusing since it actually stands for Primary
Bluetooth Controller. Which is a term that has been used in the latest
standard. However from a legacy point of view there only really have
been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of
Bluetooth introduced Low Energy (LE) and made this terminology a little
bit confused since Dual Mode Controllers include BR/EDR and LE. To
simplify this the name HCI_PRIMARY stands for the Primary Controller
which can be a single mode or dual mode controller.
Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: default avatarJohan Hedberg <johan.hedberg@intel.com>
      ca8bee5d
  19. 29 Jan, 2016 1 commit
  21. 19 Nov, 2015 2 commits
  23. 05 Nov, 2015 3 commits
  25. 10 Aug, 2015 1 commit
    • Jakub Pawlowski's avatar
      Bluetooth: Enable new connection establishment procedure. · fa142220
      Jakub Pawlowski authored 
      
Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.

This patch enables new connection establishment procedure. Instead of just
sending HCI_OP_LE_CREATE_CONN to controller, "connect" will add device to
kernel whitelist and start scan. If advertisement is received, it'll be
compared against whitelist and then trigger connection if it matches.
That fixes mentioned reconnect issue for  already paired devices. It also
make whole connection procedure more robust. We can try to connect to
multiple devices at same time now, even though controller allow only one.
Signed-off-by: default avatarJakub Pawlowski <jpawlowski@google.com>
Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
      fa142220
  27. 05 Jul, 2015 1 commit
    • Linus Torvalds's avatar
      bluetooth: fix list handling · 9b284cbd
      Linus Torvalds authored 
      Commit 835a6a2f

 ("Bluetooth: Stop sabotaging list poisoning")
thought that the code was sabotaging the list poisoning when NULL'ing
out the list pointers and removed it.

But what was going on was that the bluetooth code was using NULL
pointers for the list as a way to mark it empty, and that commit just
broke it (and replaced the test with NULL with a "list_empty()" test on
a uninitialized list instead, breaking things even further).

So fix it all up to use the regular and real list_empty() handling
(which does not use NULL, but a pointer to itself), also making sure to
initialize the list properly (the previous NULL case was initialized
implicitly by the session being allocated with kzalloc())

This is a combination of patches by Marcel Holtmann and Tedd Ho-Jeong
An.

[ I would normally expect to get this through the bt tree, but I'm going
  to release -rc1, so I'm just committing this directly   - Linus ]
Reported-and-tested-by: default avatarJörg Otte <jrg.otte@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Original-by: default avatarTedd Ho-Jeong An <tedd.an@intel.com>
Original-by: Marcel Holtmann <marcel@holtmann.org>:
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      9b284cbd
  29. 30 Jun, 2015 1 commit
    • Tedd Ho-Jeong An's avatar
      Bluetooth: Reinitialize the list after deletion for session user list · ab944c83
      Tedd Ho-Jeong An authored 
      
If the user->list is deleted with list_del(), it doesn't initialize the
entry which can cause the issue with list_empty(). According to the
comment from the list.h, list_empty() returns false even if the list is
empty and put the entry in an undefined state.

/**
 * list_del - deletes entry from list.
 * @entry: the element to delete from the list.
 * Note: list_empty() on entry does not return true after this, the entry is
 * in an undefined state.
 */

Because of this behavior, list_empty() returns false even if list is empty
when the device is reconnected.

So, user->list needs to be re-initialized after list_del(). list.h already
have a macro list_del_init() which deletes the entry and initailze it again.
Signed-off-by: default avatarTedd Ho-Jeong An <tedd.an@intel.com>
Tested-by: default avatarJörg Otte <jrg.otte@gmail.com>
Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
      ab944c83
  31. 10 Jun, 2015 1 commit
  33. 09 Jun, 2015 1 commit
  35. 30 Mar, 2015 1 commit
  37. 13 Mar, 2015 2 commits
  39. 19 Feb, 2015 3 commits
  41. 16 Feb, 2015 1 commit
    • Johan Hedberg's avatar
      Bluetooth: Fix accepting early data on fixed channels · 315917e0
      Johan Hedberg authored 
      
On BR/EDR the L2CAP channel instances for fixed channels have so far
been marked as ready only once the L2CAP information req/rsp procedure
is complete and we have the fixed channel mask. This could however lead
to data being dropped if we receive it on the channel before knowing the
remote mask.

Since it is valid for a remote to send data this early, simply assume
that the channel is supported when we receive data on it. So far this
hasn't been noticed much because of limited use of fixed channels on
BR/EDR, but e.g. with SMP over BR/EDR this is already now visible with
automated tests failing randomly.
Signed-off-by: default avatarJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
      315917e0
  43. 15 Jan, 2015 3 commits
  45. 02 Jan, 2015 1 commit
  47. 09 Dec, 2014 2 commits
  49. 06 Dec, 2014 1 commit
  51. 03 Dec, 2014 1 commit
  53. 02 Dec, 2014 1 commit
    • Johan Hedberg's avatar
      Bluetooth: Track both local and remote L2CAP fixed channel mask · 0bd49fc7
      Johan Hedberg authored 
      
To pave the way for future fixed channels to be added easily we should
track both the local and remote mask on a per-L2CAP connection (struct
l2cap_conn) basis. So far the code has used a global variable in a racy
way which anyway needs fixing.

This patch renames the existing conn->fixed_chan_mask that tracked
the remote mask to conn->remote_fixed_chan and adds a new variable
conn->local_fixed_chan to track the local mask. Since the HS support
info is now available in the local mask we can remove the
conn->hs_enabled variable.
Signed-off-by: default avatarJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
      0bd49fc7
  55. 27 Nov, 2014 1 commit
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7