- 07 Jun, 2017 40 commits
-
-
Johan Hovold authored
commit d3ba126a upstream. This reverts commit 8ee3fde0. The new serdev bus hooked into the tty layer in tty_port_register_device() by registering a serdev controller instead of a tty device whenever a serdev client is present, and by deregistering the controller in the tty-port destructor. This is broken in several ways: Firstly, it leads to a NULL-pointer dereference whenever a tty driver later deregisters its devices as no corresponding character device will exist. Secondly, far from every tty driver uses tty-port refcounting (e.g. serial core) so the serdev devices might never be deregistered or deallocated. Thirdly, deregistering at tty-port destruction is too late as the underlying device and structures may be long gone by then. A port is not released before an open tty device is closed, something which a registered serdev client can prevent from ever happening. A driver callback while the device is gone typically also leads to crashes. Many tty drivers even keep their ports around until the driver is unloaded (e.g. serial core), something which even if a late callback never happens, leads to leaks if a device is unbound from its driver and is later rebound. The right solution here is to add a new tty_port_unregister_device() helper and to never call tty_device_unregister() whenever the port has been claimed by serdev, but since this requires modifying just about every tty driver (and multiple subsystems) it will need to be done incrementally. Reverting the offending patch is the first step in fixing the broken lifetime assumptions. A follow-up patch will add a new pair of tty-device registration helpers, which a vetted tty driver can use to support serdev (initially serial core). When every tty driver uses the serdev helpers (at least for deregistration), we can add serdev registration to tty_port_register_device() again. Note that this also fixes another issue with serdev, which currently allocates and registers a serdev controller for every tty device registered using tty_port_device_register() only to immediately deregister and deallocate it when the corresponding OF node or serdev child node is missing. This should be addressed before enabling serdev for hot-pluggable buses. Signed-off-by:
Johan Hovold <johan@kernel.org> Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jeremy Kerr authored
commit d75e4919 upstream. Commit ac29c640 ("powerpc/mm: Replace _PAGE_USER with _PAGE_PRIVILEGED") swapped _PAGE_USER for _PAGE_PRIVILEGED, and introduced check_pte_access() which denied kernel access to non-_PAGE_PRIVILEGED pages. However, it didn't add _PAGE_PRIVILEGED to the hash fault handler for spufs' kernel accesses, so the DMAs required to establish SPE memory no longer work. This change adds _PAGE_PRIVILEGED to the hash fault handler for kernel accesses. Fixes: ac29c640 ("powerpc/mm: Replace _PAGE_USER with _PAGE_PRIVILEGED") Signed-off-by:
Jeremy Kerr <jk@ozlabs.org> Reported-by:
Sombat Tragolgosol <sombat3960@gmail.com> Reviewed-by:
Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Michael Neuling authored
commit d957fb4d upstream. Currently if you disable CONFIG_PPC_RADIX_MMU you'll crash on boot on a P9. This is because we still set MMU_FTR_TYPE_RADIX via ibm,pa-features and MMU_FTR_TYPE_RADIX is what's used for code patching in much of the asm code (ie. slb_miss_realmode) This patch fixes the problem by stopping MMU_FTR_TYPE_RADIX from being set from ibm.pa-features. We may eventually end up removing the CONFIG_PPC_RADIX_MMU option completely but until then this fixes the issue. Fixes: 17a3dd2f ("powerpc/mm/radix: Use firmware feature to enable Radix MMU") Signed-off-by:
Michael Neuling <mikey@neuling.org> Signed-off-by:
-
Richard Narron authored
commit 239e250e upstream. This fixes a problem with reading files larger than 2GB from a UFS-2 file system: https://bugzilla.kernel.org/show_bug.cgi?id=195721 The incorrect UFS s_maxsize limit became a problem as of commit c2a9737f ("vfs,mm: fix a dead loop in truncate_inode_pages_range()") which started using s_maxbytes to avoid a page index overflow in do_generic_file_read(). That caused files to be truncated on UFS-2 file systems because the default maximum file size is 2GB (MAX_NON_LFS) and UFS didn't update it. Here I simply increase the default to a common value used by other file systems. Signed-off-by:
Richard Narron <comet.berkeley@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Will B <will.brokenbourgh2877@gmail.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Liam R. Howlett authored
[ Upstream commit 48078d2d ] The ftrace function_graph time measurements of a given function is not accurate according to those recorded by ftrace using the function filters. This change pulls the x86_64 fix from 'commit 722b3c74 ("ftrace/graph: Trace function entry before updating index")' into the sparc specific prepare_ftrace_return which stops ftrace from counting interrupted tasks in the time measurement. Example measurements for select_task_rq_fair running "hackbench 100 process 1000": | tracing/trace_stat/function0 | function_graph Before patch | 2.802 us | 4.255 us After patch | 2.749 us | 3.094 us Signed-off-by:
Liam R. Howlett <Liam.Howlett@Oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Orlando Arias authored
[ Upstream commit deba804c ] Greetings, GCC 7 introduced the -Wstringop-overflow flag to detect buffer overflows in calls to string handling functions [1][2]. Due to the way ``empty_zero_page'' is declared in arch/sparc/include/setup.h, this causes a warning to trigger at compile time in the function mem_init(), which is subsequently converted to an error. The ensuing patch fixes this issue and aligns the declaration of empty_zero_page to that of other architectures. Thank you. Cheers, Orlando. [1] https://gcc.gnu.org/ml/gcc-patches/2016-10/msg02308.html [2] https://gcc.gnu.org/gcc-7/changes.htmlSigned-off-by:
Orlando Arias <oarias@knights.ucf.edu> -------------------------------------------------------------------------------- Signed-off-by:
-
Nitin Gupta authored
[ Upstream commit b6c41cb0 ] An incorrect huge page alignment check caused mmap failure for 64K pages when MAP_FIXED is used with address not aligned to HPAGE_SIZE. Orabug: 25885991 Fixes: dcd1912d ("sparc64: Add 64K page size support") Signed-off-by:
Nitin Gupta <nitin.m.gupta@oracle.com> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit 3c2ce60b ] Current limits with regards to processing program paths do not really reflect today's needs anymore due to programs becoming more complex and verifier smarter, keeping track of more data such as const ALU operations, alignment tracking, spilling of PTR_TO_MAP_VALUE_ADJ registers, and other features allowing for smarter matching of what LLVM generates. This also comes with the side-effect that we result in fewer opportunities to prune search states and thus often need to do more work to prove safety than in the past due to different register states and stack layout where we mismatch. Generally, it's quite hard to determine what caused a sudden increase in complexity, it could be caused by something as trivial as a single branch somewhere at the beginning of the program where LLVM assigned a stack slot that is marked differently throughout other branches and thus causing a mismatch, where verifier then needs to prove safety for the whole rest of the program. Subsequently, programs with even less than half the insn size limit can get rejected. We noticed that while some programs load fine under pre 4.11, they get rejected due to hitting limits on more recent kernels. We saw that in the vast majority of cases (90+%) pruning failed due to register mismatches. In case of stack mismatches, majority of cases failed due to different stack slot types (invalid, spill, misc) rather than differences in spilled registers. This patch makes pruning more aggressive by also adding markers that sit at conditional jumps as well. Currently, we only mark jump targets for pruning. For example in direct packet access, these are usually error paths where we bail out. We found that adding these markers, it can reduce number of processed insns by up to 30%. Another option is to ignore reg->id in probing PTR_TO_MAP_VALUE_OR_NULL registers, which can help pruning slightly as well by up to 7% observed complexity reduction as stand-alone. Meaning, if a previous path with register type PTR_TO_MAP_VALUE_OR_NULL for map X was found to be safe, then in the current state a PTR_TO_MAP_VALUE_OR_NULL register for the same map X must be safe as well. Last but not least the patch also adds a scheduling point and bumps the current limit for instructions to be processed to a more adequate value. Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit a316338c ] trie_alloc() always needs to have BPF_F_NO_PREALLOC passed in via attr->map_flags, since it does not support preallocation yet. We check the flag, but we never copy the flag into trie->map.map_flags, which is later on exposed into fdinfo and used by loaders such as iproute2. Latter uses this in bpf_map_selfcheck_pinned() to test whether a pinned map has the same spec as the one from the BPF obj file and if not, bails out, which is currently the case for lpm since it exposes always 0 as flags. Also copy over flags in array_map_alloc() and stack_map_alloc(). They always have to be 0 right now, but we should make sure to not miss to copy them over at a later point in time when we add actual flags for them to use. Fixes: b95a5c4d ("bpf: add a longest prefix match trie map implementation") Reported-by:
Jarno Rajahalme <jarno@covalent.io> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit 41703a73 ] The bpf_clone_redirect() still needs to be listed in bpf_helper_changes_pkt_data() since we call into bpf_try_make_head_writable() from there, thus we need to invalidate prior pkt regs as well. Fixes: 36bbef52 ("bpf: direct packet write and access for helpers for clsact progs") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 3fb07daf ] Andrey Konovalov reported crashes in ipv4_mtu() I could reproduce the issue with KASAN kernels, between 10.246.7.151 and 10.246.7.152 : 1) 20 concurrent netperf -t TCP_RR -H 10.246.7.152 -l 1000 & 2) At the same time run following loop : while : do ip ro add 10.246.7.152 dev eth0 src 10.246.7.151 mtu 1500 ip ro del 10.246.7.152 dev eth0 src 10.246.7.151 mtu 1500 done Cong Wang attempted to add back rt->fi in commit 82486aa6 ("ipv4: restore rt->fi for reference counting") but this proved to add some issues that were complex to solve. Instead, I suggested to add a refcount to the metrics themselves, being a standalone object (in particular, no reference to other objects) I tried to make this patch as small as possible to ease its backport, instead of being super clean. Note that we believe that only ipv4 dst need to take care of the metric refcount. But if this is wrong, this patch adds the basic infrastructure to extend this to other families. Many thanks to Julian Anastasov for reviewing this patch, and Cong Wang for his efforts on this problem. Fixes: 2860583f ("ipv4: Kill rt->fi") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Andrey Konovalov <andreyknvl@google.com> Reviewed-by:
Julian Anastasov <ja@ssi.bg> Acked-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Peter Dawson authored
[ Upstream commit 0e9a7095 ] This fix addresses two problems in the way the DSCP field is formulated on the encapsulating header of IPv6 tunnels. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195661 1) The IPv6 tunneling code was manipulating the DSCP field of the encapsulating packet using the 32b flowlabel. Since the flowlabel is only the lower 20b it was incorrect to assume that the upper 12b containing the DSCP and ECN fields would remain intact when formulating the encapsulating header. This fix handles the 'inherit' and 'fixed-value' DSCP cases explicitly using the extant dsfield u8 variable. 2) The use of INET_ECN_encapsulate(0, dsfield) in ip6_tnl_xmit was incorrect and resulted in the DSCP value always being set to 0. Commit 90427ef5 ("ipv6: fix flow labels when the traffic class is non-0") caused the regression by masking out the flowlabel which exposed the incorrect handling of the DSCP portion of the flowlabel in ip6_tunnel and ip6_gre. Fixes: 90427ef5 ("ipv6: fix flow labels when the traffic class is non-0") Signed-off-by:
Peter Dawson <peter.a.dawson@boeing.com> Signed-off-by:
-
Davide Caratti authored
[ Upstream commit 804ec7eb ] sometimes ICMP replies to INIT chunks are ignored by the client, even if the encapsulated SCTP headers match an open socket. This happens when the ICMP packet is carried by a paged skb: use skb_header_pointer() to read packet contents beyond the SCTP header, so that chunk header and initiate tag are validated correctly. v2: - don't use skb_header_pointer() to read the transport header, since icmp_socket_deliver() already puts these 8 bytes in the linear area. - change commit message to make specific reference to INIT chunks. Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Reviewed-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Wei Wang authored
[ Upstream commit ba615f67 ] Fastopen API should be used to perform fastopen operations on the TCP socket. It does not make sense to use fastopen API to perform disconnect by calling it with AF_UNSPEC. The fastopen data path is also prone to race conditions and bugs when using with AF_UNSPEC. One issue reported and analyzed by Vegard Nossum is as follows: +++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Thread A: Thread B: ------------------------------------------------------------------------ sendto() - tcp_sendmsg() - sk_stream_memory_free() = 0 - goto wait_for_sndbuf - sk_stream_wait_memory() - sk_wait_event() // sleep | sendto(flags=MSG_FASTOPEN, dest_addr=AF_UNSPEC) | - tcp_sendmsg() | - tcp_sendmsg_fastopen() | - __inet_stream_connect() | - tcp_disconnect() //because of AF_UNSPEC | - tcp_transmit_skb()// send RST | - return 0; // no reconnect! | - sk_stream_wait_connect() | - sock_error() | - xchg(&sk->sk_err, 0) | - return -ECONNRESET - ... // wake up, see sk->sk_err == 0 - skb_entail() on TCP_CLOSE socket If the connection is reopened then we will send a brand new SYN packet after thread A has already queued a buffer. At this point I think the socket internal state (sequence numbers etc.) becomes messed up. When the new connection is closed, the FIN-ACK is rejected because the sequence number is outside the window. The other side tries to retransmit, but __tcp_retransmit_skb() calls tcp_trim_head() on an empty skb which corrupts the skb data length and hits a BUG() in copy_and_csum_bits(). +++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Hence, this patch adds a check for AF_UNSPEC in the fastopen data path and return EOPNOTSUPP to user if such case happens. Fixes: cf60af03 ("tcp: Fast Open client - sendmsg(MSG_FASTOPEN)") Reported-by:
Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by:
Wei Wang <weiwan@google.com> Signed-off-by:
-
Eric Garver authored
[ Upstream commit 11387fe4 ] Since 9b4437a5 ("geneve: Unify LWT and netdev handling.") fill_info does not return UDP_ZERO_CSUM6_RX when using COLLECT_METADATA. This is because it uses ip_tunnel_info_af() with the device level info, which is not valid for COLLECT_METADATA. Fix by checking for the presence of the actual sockets. Fixes: 9b4437a5 ("geneve: Unify LWT and netdev handling.") Signed-off-by:
Eric Garver <e@erig.me> Acked-by:
Pravin B Shelar <pshelar@ovn.org> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit 2836b4f2 ] Since virtio does not provide it's own ndo_features_check handler, TSO, and now checksum offload, are disabled for stacked vlans. Re-enable the support and let the host take care of it. This restores/improves Guest-to-Guest performance over Q-in-Q vlans. Acked-by:
Jason Wang <jasowang@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit cc6e9de6 ] At least some of the be2net cards do not seem to be capabled of performing checksum offload computions on Q-in-Q packets. In these case, the recevied checksum on the remote is invalid and TCP syn packets are dropped. This patch adds a call to check disbled acceleration features on Q-in-Q tagged traffic. CC: Sathya Perla <sathya.perla@broadcom.com> CC: Ajit Khaparde <ajit.khaparde@broadcom.com> CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> CC: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit 35d2f80b ] It appears that TCP checksum offloading has been broken for Q-in-Q vlans. The behavior was execerbated by the series commit afb0bc97 ("Merge branch 'stacked_vlan_tso'") that that enabled accleleration features on stacked vlans. However, event without that series, it is possible to trigger this issue. It just requires a lot more specialized configuration. The root cause is the interaction between how netdev_intersect_features() works, the features actually set on the vlan devices and HW having the ability to run checksum with longer headers. The issue starts when netdev_interesect_features() replaces NETIF_F_HW_CSUM with a combination of NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM, if the HW advertises IP|IPV6 specific checksums. This happens for tagged and multi-tagged packets. However, HW that enables IP|IPV6 checksum offloading doesn't gurantee that packets with arbitrarily long headers can be checksummed. This patch disables IP|IPV6 checksums on the packet for multi-tagged packets. CC: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> CC: Michal Kubecek <mkubecek@suse.cz> Signed-off-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by:
-
Andrew Lunn authored
[ Upstream commit f2899788 ] The 88m1101 has an errata when configuring autoneg. However, it was being applied to many other Marvell PHYs as well. Limit its scope to just the 88m1101. Fixes: 76884679 ("phylib: Add support for Marvell 88e1111S and 88e1145") Reported-by:
Daniel Walker <danielwa@cisco.com> Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Acked-by:
Harini Katakam <harinik@xilinx.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Mohamad Haj Yahia authored
[ Upstream commit 73dd3a48 ] Currently when firmware command gets stuck or it takes long time to complete, the driver command will get timeout and the command slot is freed and can be used for new commands, and if the firmware receive new command on the old busy slot its behavior is unexpected and this could be harmful. To fix this when the driver command gets timeout we return failure, but we don't free the command slot and we wait for the firmware to explicitly respond to that command. Once all the entries are busy we will stop processing new firmware commands. Fixes: 9cba4ebc ('net/mlx5: Fix potential deadlock in command mode change') Signed-off-by:
Mohamad Haj Yahia <mohamad@mellanox.com> Cc: kernel-team@fb.com Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Jarod Wilson authored
[ Upstream commit 751da2a6 ] As of 7bb11dc9 and 0622cab0, bond slaves in a 3ad bond are not removed from the aggregator when they are down, and the active slave count is NOT equal to number of ports in the aggregator, but rather the number of ports in the aggregator that are still enabled. The sysfs spew for bonding_show_ad_num_ports() has a comment that says "Show number of active 802.3ad ports.", but it's currently showing total number of ports, both active and inactive. Remedy it by using the same logic introduced in 0622cab0 in __bond_3ad_get_active_agg_info(), so sysfs, procfs and netlink all report the number of active ports. Note that this means that IFLA_BOND_AD_INFO_NUM_PORTS really means NUM_ACTIVE_PORTS instead of NUM_PORTS, and thus perhaps should be renamed for clarity. Lightly tested on a dual i40e lacp bond, simulating link downs with an ip link set dev <slave2> down, was able to produce the state where I could see both in the same aggregator, but a number of ports count of 1. MII Status: up Active Aggregator Info: Aggregator ID: 1 Number of ports: 2 <--- Slave Interface: ens10 MII Status: up <--- Aggregator ID: 1 Slave Interface: ens11 MII Status: up Aggregator ID: 1 MII Status: up Active Aggregator Info: Aggregator ID: 1 Number of ports: 1 <--- Slave Interface: ens10 MII Status: down <--- Aggregator ID: 1 Slave Interface: ens11 MII Status: up Aggregator ID: 1 CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: netdev@vger.kernel.org Signed-off-by:
Jarod Wilson <jarod@redhat.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 232cd35d ] Andrey Konovalov and idaifish@gmail.com reported crashes caused by one skb shared_info being overwritten from __ip6_append_data() Andrey program lead to following state : copy -4200 datalen 2000 fraglen 2040 maxfraglen 2040 alloclen 2048 transhdrlen 0 offset 0 fraggap 6200 The skb_copy_and_csum_bits(skb_prev, maxfraglen, data + transhdrlen, fraggap, 0); is overwriting skb->head and skb_shared_info Since we apparently detect this rare condition too late, move the code earlier to even avoid allocating skb and risking crashes. Once again, many thanks to Andrey and syzkaller team. Signed-off-by:
-
Xin Long authored
[ Upstream commit 6d18c732 ] Since commit 76b91c32 ("bridge: stp: when using userspace stp stop kernel hello and hold timers"), bridge would not start hello_timer if stp_enabled is not KERNEL_STP when br_dev_open. The problem is even if users set stp_enabled with KERNEL_STP later, the timer will still not be started. It causes that KERNEL_STP can not really work. Users have to re-ifup the bridge to avoid this. This patch is to fix it by starting br->hello_timer when enabling KERNEL_STP in br_stp_start. As an improvement, it's also to start hello_timer again only when br->stp_enabled is KERNEL_STP in br_hello_timer_expired, there is no reason to start the timer again when it's NO_STP. Fixes: 76b91c32 ("bridge: stp: when using userspace stp stop kernel hello and hold timers") Reported-by:
Haidong Li <haili@redhat.com> Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by:
Ivan Vecera <cera@cera.cz> Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit 486181bc ] In their infinite wisdom, and never ending quest for end user frustration, Lenovo has decided to use a new USB device ID for the wwan modules in their 2017 laptops. The actual hardware is still the Sierra Wireless EM7455 or EM7430, depending on region. Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Tobias Jungel authored
[ Upstream commit a2858602 ] Currently it is allowed to set the default pvid of a bridge to a value above VLAN_VID_MASK (0xfff). This patch adds a check to br_validate and returns -EINVAL in case the pvid is out of bounds. Reproduce by calling: [root@test ~]# ip l a type bridge [root@test ~]# ip l a type dummy [root@test ~]# ip l s bridge0 type bridge vlan_filtering 1 [root@test ~]# ip l s bridge0 type bridge vlan_default_pvid 9999 [root@test ~]# ip l s dummy0 master bridge0 [root@test ~]# bridge vlan port vlan ids bridge0 9999 PVID Egress Untagged dummy0 9999 PVID Egress Untagged Fixes: 0f963b75 ("bridge: netlink: add support for default_pvid") Acked-by:
Tobias Jungel <tobias.jungel@bisdn.de> Acked-by:
Sabrina Dubroca <sd@queasysnail.net> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 7dd7eb95 ] Do not use unsigned variables to see if it returns a negative error or not. Fixes: 2423496a ("ipv6: Prevent overrun when parsing v6 header options") Reported-by:
Julia Lawall <julia.lawall@lip6.fr> Signed-off-by:
-
Craig Gallek authored
[ Upstream commit 2423496a ] The KASAN warning repoted below was discovered with a syzkaller program. The reproducer is basically: int s = socket(AF_INET6, SOCK_RAW, NEXTHDR_HOP); send(s, &one_byte_of_data, 1, MSG_MORE); send(s, &more_than_mtu_bytes_data, 2000, 0); The socket() call sets the nexthdr field of the v6 header to NEXTHDR_HOP, the first send call primes the payload with a non zero byte of data, and the second send call triggers the fragmentation path. The fragmentation code tries to parse the header options in order to figure out where to insert the fragment option. Since nexthdr points to an invalid option, the calculation of the size of the network header can made to be much larger than the linear section of the skb and data is read outside of it. This fix makes ip6_find_1stfrag return an error if it detects running out-of-bounds. [ 42.361487] ================================================================== [ 42.364412] BUG: KASAN: slab-out-of-bounds in ip6_fragment+0x11c8/0x3730 [ 42.365471] Read of size 840 at addr ffff88000969e798 by task ip6_fragment-oo/3789 [ 42.366469] [ 42.366696] CPU: 1 PID: 3789 Comm: ip6_fragment-oo Not tainted 4.11.0+ #41 [ 42.367628] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.1-1ubuntu1 04/01/2014 [ 42.368824] Call Trace: [ 42.369183] dump_stack+0xb3/0x10b [ 42.369664] print_address_description+0x73/0x290 [ 42.370325] kasan_report+0x252/0x370 [ 42.370839] ? ip6_fragment+0x11c8/0x3730 [ 42.371396] check_memory_region+0x13c/0x1a0 [ 42.371978] memcpy+0x23/0x50 [ 42.372395] ip6_fragment+0x11c8/0x3730 [ 42.372920] ? nf_ct_expect_unregister_notifier+0x110/0x110 [ 42.373681] ? ip6_copy_metadata+0x7f0/0x7f0 [ 42.374263] ? ip6_forward+0x2e30/0x2e30 [ 42.374803] ip6_finish_output+0x584/0x990 [ 42.375350] ip6_output+0x1b7/0x690 [ 42.375836] ? ip6_finish_output+0x990/0x990 [ 42.376411] ? ip6_fragment+0x3730/0x3730 [ 42.376968] ip6_local_out+0x95/0x160 [ 42.377471] ip6_send_skb+0xa1/0x330 [ 42.377969] ip6_push_pending_frames+0xb3/0xe0 [ 42.378589] rawv6_sendmsg+0x2051/0x2db0 [ 42.379129] ? rawv6_bind+0x8b0/0x8b0 [ 42.379633] ? _copy_from_user+0x84/0xe0 [ 42.380193] ? debug_check_no_locks_freed+0x290/0x290 [ 42.380878] ? ___sys_sendmsg+0x162/0x930 [ 42.381427] ? rcu_read_lock_sched_held+0xa3/0x120 [ 42.382074] ? sock_has_perm+0x1f6/0x290 [ 42.382614] ? ___sys_sendmsg+0x167/0x930 [ 42.383173] ? lock_downgrade+0x660/0x660 [ 42.383727] inet_sendmsg+0x123/0x500 [ 42.384226] ? inet_sendmsg+0x123/0x500 [ 42.384748] ? inet_recvmsg+0x540/0x540 [ 42.385263] sock_sendmsg+0xca/0x110 [ 42.385758] SYSC_sendto+0x217/0x380 [ 42.386249] ? SYSC_connect+0x310/0x310 [ 42.386783] ? __might_fault+0x110/0x1d0 [ 42.387324] ? lock_downgrade+0x660/0x660 [ 42.387880] ? __fget_light+0xa1/0x1f0 [ 42.388403] ? __fdget+0x18/0x20 [ 42.388851] ? sock_common_setsockopt+0x95/0xd0 [ 42.389472] ? SyS_setsockopt+0x17f/0x260 [ 42.390021] ? entry_SYSCALL_64_fastpath+0x5/0xbe [ 42.390650] SyS_sendto+0x40/0x50 [ 42.391103] entry_SYSCALL_64_fastpath+0x1f/0xbe [ 42.391731] RIP: 0033:0x7fbbb711e383 [ 42.392217] RSP: 002b:00007ffff4d34f28 EFLAGS: 00000246 ORIG_RAX: 000000000000002c [ 42.393235] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fbbb711e383 [ 42.394195] RDX: 0000000000001000 RSI: 00007ffff4d34f60 RDI: 0000000000000003 [ 42.395145] RBP: 0000000000000046 R08: 00007ffff4d34f40 R09: 0000000000000018 [ 42.396056] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000400aad [ 42.396598] R13: 0000000000000066 R14: 00007ffff4d34ee0 R15: 00007fbbb717af00 [ 42.397257] [ 42.397411] Allocated by task 3789: [ 42.397702] save_stack_trace+0x16/0x20 [ 42.398005] save_stack+0x46/0xd0 [ 42.398267] kasan_kmalloc+0xad/0xe0 [ 42.398548] kasan_slab_alloc+0x12/0x20 [ 42.398848] __kmalloc_node_track_caller+0xcb/0x380 [ 42.399224] __kmalloc_reserve.isra.32+0x41/0xe0 [ 42.399654] __alloc_skb+0xf8/0x580 [ 42.400003] sock_wmalloc+0xab/0xf0 [ 42.400346] __ip6_append_data.isra.41+0x2472/0x33d0 [ 42.400813] ip6_append_data+0x1a8/0x2f0 [ 42.401122] rawv6_sendmsg+0x11ee/0x2db0 [ 42.401505] inet_sendmsg+0x123/0x500 [ 42.401860] sock_sendmsg+0xca/0x110 [ 42.402209] ___sys_sendmsg+0x7cb/0x930 [ 42.402582] __sys_sendmsg+0xd9/0x190 [ 42.402941] SyS_sendmsg+0x2d/0x50 [ 42.403273] entry_SYSCALL_64_fastpath+0x1f/0xbe [ 42.403718] [ 42.403871] Freed by task 1794: [ 42.404146] save_stack_trace+0x16/0x20 [ 42.404515] save_stack+0x46/0xd0 [ 42.404827] kasan_slab_free+0x72/0xc0 [ 42.405167] kfree+0xe8/0x2b0 [ 42.405462] skb_free_head+0x74/0xb0 [ 42.405806] skb_release_data+0x30e/0x3a0 [ 42.406198] skb_release_all+0x4a/0x60 [ 42.406563] consume_skb+0x113/0x2e0 [ 42.406910] skb_free_datagram+0x1a/0xe0 [ 42.407288] netlink_recvmsg+0x60d/0xe40 [ 42.407667] sock_recvmsg+0xd7/0x110 [ 42.408022] ___sys_recvmsg+0x25c/0x580 [ 42.408395] __sys_recvmsg+0xd6/0x190 [ 42.408753] SyS_recvmsg+0x2d/0x50 [ 42.409086] entry_SYSCALL_64_fastpath+0x1f/0xbe [ 42.409513] [ 42.409665] The buggy address belongs to the object at ffff88000969e780 [ 42.409665] which belongs to the cache kmalloc-512 of size 512 [ 42.410846] The buggy address is located 24 bytes inside of [ 42.410846] 512-byte region [ffff88000969e780, ffff88000969e980) [ 42.411941] The buggy address belongs to the page: [ 42.412405] page:ffffea000025a780 count:1 mapcount:0 mapping: (null) index:0x0 compound_mapcount: 0 [ 42.413298] flags: 0x100000000008100(slab|head) [ 42.413729] raw: 0100000000008100 0000000000000000 0000000000000000 00000001800c000c [ 42.414387] raw: ffffea00002a9500 0000000900000007 ffff88000c401280 0000000000000000 [ 42.415074] page dumped because: kasan: bad access detected [ 42.415604] [ 42.415757] Memory state around the buggy address: [ 42.416222] ffff88000969e880: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 42.416904] ffff88000969e900: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 42.417591] >ffff88000969e980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 42.418273] ^ [ 42.418588] ffff88000969ea00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 42.419273] ffff88000969ea80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 42.419882] ================================================================== Reported-by:
Craig Gallek <kraig@google.com> Signed-off-by:
-
David Ahern authored
[ Upstream commit f6c5775f ] In general, rtnetlink dumps do not anticipate failure to dump a single object (e.g., link or route) on a single pass. As both route and link objects have grown via more attributes, that is no longer a given. netlink dumps can handle a failure if the dump function returns an error; specifically, netlink_dump adds the return code to the response if it is <= 0 so userspace is notified of the failure. The missing piece is the rtnetlink dump functions returning the error. Fix route and link dump functions to return the errors if no object is added to an skb (detected by skb->len != 0). IPv6 route dumps (rt6_dump_route) already return the error; this patch updates IPv4 and link dumps. Other dump functions may need to be ajusted as well. Reported-by:
Jan Moskyto Matejka <mq@ucw.cz> Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Christoph Hellwig authored
[ Upstream commit 19a0f7e3 ] The driver explicitly bypasses APIs to register all memory once a connection is made, and thus allows remote access to memory. Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Leon Romanovsky <leon@kernel.org> Acked-by:
Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by:
-
Ursula Braun authored
[ Upstream commit 263eec9b ] Currently, SMC enables remote access to physical memory when a user has successfully configured and established an SMC-connection until ten minutes after the last SMC connection is closed. Because this is considered a security risk, drivers are supposed to use IB_PD_UNSAFE_GLOBAL_RKEY in such a case. This patch changes the current SMC code to use IB_PD_UNSAFE_GLOBAL_RKEY. This improves user awareness, but does not remove the security risk itself. Signed-off-by:
-
Soheil Hassas Yeganeh authored
[ Upstream commit bafbb9c7 ] tcp_ack() can call tcp_fragment() which may dededuct the value tp->fackets_out when MSS changes. When prior_fackets is larger than tp->fackets_out, tcp_clean_rtx_queue() can invoke tcp_update_reordering() with negative values. This results in absurd tp->reodering values higher than sysctl_tcp_max_reordering. Note that tcp_update_reordering indeeds sets tp->reordering to min(sysctl_tcp_max_reordering, metric), but because the comparison is signed, a negative metric always wins. Fixes: c7caf8d3 ("[TCP]: Fix reord detection due to snd_una covered holes") Reported-by:
Rebecca Isaacs <risaacs@google.com> Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
-
Gal Pressman authored
[ Upstream commit e3c19503 ] Pause bit should set when RX pause is on, not TX pause. Also, setting Asym_Pause is incorrect, and should be turned off. Fixes: 665bc539 ("net/mlx5e: Use new ethtool get/set link ksettings API") Signed-off-by:
Gal Pressman <galp@mellanox.com> Cc: kernel-team@fb.com Signed-off-by:
-
Gal Pressman authored
[ Upstream commit b383b544 ] Query the operational pause from firmware (PFCC register) instead of always passing zeros. Fixes: 665bc539 ("net/mlx5e: Use new ethtool get/set link ksettings API") Signed-off-by:
-
Douglas Caetano dos Santos authored
[ Upstream commit d19b183c ] When using a TX ring buffer, if an error occurs processing a control message (e.g. invalid message), the net_device reference is not released. Fixes c14ac945 ("sock: enable timestamping using control messages") Signed-off-by:
Douglas Caetano dos Santos <douglascs@taghos.com.br> Acked-by:
-
Eric Dumazet authored
[ Upstream commit fdcee2cb ] SCTP needs fixes similar to 83eaddab ("ipv6/dccp: do not inherit ipv6_mc_list from parent"), otherwise bad things can happen. Signed-off-by:
-
Xin Long authored
[ Upstream commit dbc2b5e9 ] Commit 0ca50d12 ("sctp: fix src address selection if using secondary addresses") has fixed a src address selection issue when using secondary addresses for ipv4. Now sctp ipv6 also has the similar issue. When using a secondary address, sctp_v6_get_dst tries to choose the saddr which has the most same bits with the daddr by sctp_v6_addr_match_len. It may make some cases not work as expected. hostA: [1] fd21:356b:459a:cf10::11 (eth1) [2] fd21:356b:459a:cf20::11 (eth2) hostB: [a] fd21:356b:459a:cf30::2 (eth1) [b] fd21:356b:459a:cf40::2 (eth2) route from hostA to hostB: fd21:356b:459a:cf30::/64 dev eth1 metric 1024 mtu 1500 The expected path should be: fd21:356b:459a:cf10::11 <-> fd21:356b:459a:cf30::2 But addr[2] matches addr[a] more bits than addr[1] does, according to sctp_v6_addr_match_len. It causes the path to be: fd21:356b:459a:cf20::11 <-> fd21:356b:459a:cf30::2 This patch is to fix it with the same way as Marcelo's fix for sctp ipv4. As no ip_dev_find for ipv6, this patch is to use ipv6_chk_addr to check if the saddr is in a dev instead. Note that for backwards compatibility, it will still do the addr_match_len check here when no optimal is found. Reported-by:
Patrick Talbert <ptalbert@redhat.com> Signed-off-by:
-
Jon Paul Maloy authored
[ Upstream commit 844cf763 ] The macro tipc_wait_for_cond() is embedding the macro sk_wait_event() to fulfil its task. The latter, in turn, is evaluating the stated condition outside the socket lock context. This is problematic if the condition is accessing non-trivial data structures which may be altered by incoming interrupts, as is the case with the cong_links() linked list, used by socket to keep track of the current set of congested links. We sometimes see crashes when this list is accessed by a condition function at the same time as a SOCK_WAKEUP interrupt is removing an element from the list. We fix this by expanding selected parts of sk_wait_event() into the outer macro, while ensuring that all evaluations of a given condition are performed under socket lock protection. Fixes: commit 365ad353 ("tipc: reduce risk of user starvation during link congestion") Reviewed-by:
Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
Yuchung Cheng authored
[ Upstream commit b451e5d2 ] This patch fixes a bug in splitting an SKB during SACK processing. Specifically if an skb contains multiple packets and is only partially sacked in the higher sequences, tcp_match_sack_to_skb() splits the skb and marks the second fragment as SACKed. The current code further attempts rounding up the first fragment to MSS boundaries. But it misses a boundary condition when the rounded-up fragment size (pkt_len) is exactly skb size. Spliting such an skb is pointless and causses a kernel warning and aborts the SACK processing. This patch universally checks such over-split before calling tcp_fragment to prevent these unnecessary warnings. Fixes: adb92db8 ("tcp: Make SACK code to split only at mss boundaries") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 9142e900 ] If CONFIG_INET is not set, net/core/sock.c can not compile : net/core/sock.c: In function ‘skb_orphan_partial’: net/core/sock.c:1810:2: error: implicit declaration of function ‘skb_is_tcp_pure_ack’ [-Werror=implicit-function-declaration] if (skb_is_tcp_pure_ack(skb)) ^ Fix this by always including <net/tcp.h> Fixes: f6ba8d33 ("netem: fix skb_orphan_partial()") Signed-off-by:
Paul Gortmaker <paul.gortmaker@windriver.com> Reported-by:
Randy Dunlap <rdunlap@infradead.org> Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit f6ba8d33 ] I should have known that lowering skb->truesize was dangerous :/ In case packets are not leaving the host via a standard Ethernet device, but looped back to local sockets, bad things can happen, as reported by Michael Madsen ( https://bugzilla.kernel.org/show_bug.cgi?id=195713 ) So instead of tweaking skb->truesize, lets change skb->destructor and keep a reference on the owner socket via its sk_refcnt. Fixes: f2f872f9 ("netem: Introduce skb_orphan_partial() helper") Signed-off-by:
Michael Madsen <mkm@nabto.com> Signed-off-by:
-
