- 11 Sep, 2020 13 commits
-
-
Kuo Zhao authored
Sample output of "ethtool -S <interface-name>" with 1 RX queue and 1 TX queue: NIC statistics: rx_packets: 1039 tx_packets: 37 rx_bytes: 822071 tx_bytes: 4100 rx_dropped: 0 tx_dropped: 0 tx_timeouts: 0 rx_skb_alloc_fail: 0 rx_buf_alloc_fail: 0 rx_desc_err_dropped_pkt: 0 interface_up_cnt: 1 interface_down_cnt: 0 reset_cnt: 0 page_alloc_fail: 0 dma_mapping_error: 0 rx_posted_desc[0]: 1365 rx_completed_desc[0]: 341 rx_bytes[0]: 215094 rx_dropped_pkt[0]: 0 rx_copybreak_pkt[0]: 3 rx_copied_pkt[0]: 3 tx_posted_desc[0]: 6 tx_completed_desc[0]: 6 tx_bytes[0]: 420 tx_wake[0]: 0 tx_stop[0]: 0 tx_event_counter[0]: 6 adminq_prod_cnt: 34 adminq_cmd_fail: 0 adminq_timeouts: 0 adminq_describe_device_cnt: 1 adminq_cfg_device_resources_cnt: 1 adminq_register_page_list_cnt: 16 adminq_unregister_page_list_cnt: 0 adminq_create_tx_queue_cnt: 8 adminq_create_rx_queue_cnt: 8 adminq_destroy_tx_queue_cnt: 0 adminq_destroy_rx_queue_cnt: 0 adminq_dcfg_device_resources_cnt: 0 adminq_set_driver_parameter_cnt: 0 Reviewed-by:Yangchun Fu <yangchun@google.com> Signed-off-by:
Kuo Zhao <kuozhao@google.com> Signed-off-by:
David Awogbemila <awogbemila@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kuo Zhao authored
This adds support for getting and setting the RX copybreak value via ethtool. Reviewed-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-next-2020-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for v5.10 First set of patches for v5.10. Most noteworthy here is ath11k getting initial support for QCA6390 and IPQ6018 devices. But most of the patches are cleanup: W=1 warning fixes, fallthrough keywords, DMA API changes and tasklet API changes. Major changes: ath10k * support SDIO firmware codedumps * support station specific TID configurations ath11k * add support for IPQ6018 * add support for QCA6390 PCI devices ath9k * add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0 rekeying wcn36xx * add support for TX ack ==================== Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.10. Major changes: ath10k * support SDIO firmware codedumps * support station specific TID configurations ath11k * add support for IPQ6018
-
YueHaibing authored
There is no caller in tree, so can remove it. Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200909135834.38448-1-yuehaibing@huawei.com
-
YueHaibing authored
There is no caller in tree, so can remove it. Signed-off-by:
-
Kalle Valo authored
If CONFIG_REMOTEPROC was disabled the linking failed with: ERROR: modpost: "rproc_get_by_phandle" [drivers/net/wireless/ath/ath11k/ath11k.ko] undefined! Compile tested only. Reported-by:
Randy Dunlap <rdunlap@infradead.org> Fixes: 1ff8ed78 ("ath11k: use remoteproc only with AHB devices") Signed-off-by:
-
Anilkumar Kolli authored
During probe ath11k_init_hw_params() is called from ath11k_core_pre_init() and is not needed agian in ath11k_core_init(). Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1 Fixes: 1ff8ed78 (ath11k: use remoteproc only with AHB devices) Signed-off-by:
Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by:
-
Venkateswara Naralasetty authored
Adding raw mode tx/rx support. Also, adding support for software crypto which depends on raw mode. To enable raw mode tx/rx: insmod ath11k.ko frame_mode=0 To enable software crypto: insmod ath11k.ko crypto_mode=1 These modes could be helpful in debugging crypto related issues. Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Manikanta Pubbisetty <mpubbise@codeaurora.org> Signed-off-by:
Venkateswara Naralasetty <vnaralas@codeaurora.org> Signed-off-by:
-
Anilkumar Kolli authored
IPQ6018 has one 5G and one 2G radio with 2x2, shares ipq8074 configurations. Tested on: IPQ6018 hw1.0 AHB WLAN.HK.2.2-02134-QCAHKSWPL_SILICONZ-1 Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Anilkumar Kolli authored
Move target CE config and target CE service config to hw_params. No functional changes. Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Anilkumar Kolli authored
Add IPQ6018 wireless driver support, its based on ath11k driver. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Luo Jiaxing authored
Fixes the following warning when using W=1 to build kernel: drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_phy_configure’: drivers/net/ethernet/smsc/smc91x.c:1039:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable] int status; Signed-off-by:
Luo Jiaxing <luojiaxing@huawei.com> Signed-off-by:
-
- 10 Sep, 2020 27 commits
-
-
David S. Miller authored
Karsten Graul says: ==================== net/smc: updates 2020-09-10 Please apply the following patch series for smc to netdev's net-next tree. This patch series is a mix of various improvements and cleanups. The patches 1 and 10 improve the handling of large parallel workloads. Patch 8 corrects a kernel config default for config CCWGROUP on s390. Patch 9 allows userspace tools to retrieve socket information for more sockets. ==================== Signed-off-by: -
Karsten Graul authored
There are 6 types of workers which exist per smc connection. 3 of them are used for listen and handshake processing, another 2 are used for close and abort processing and 1 is the tx worker that moves calls to sleeping functions into a worker. To prevent flooding of the system work queue when many connections are opened or closed at the same time (some pattern uperf implements), move those workers to one of 3 smc-specific work queues. Two work queues are module-global and used for handshake and close workers. The third work queue is defined per link group and used by the tx workers that may sleep waiting for resources of this link group. And in smc_llc_enqueue() queue the llc_event_work work to the system prio work queue because its critical that this work is started fast. Reviewed-by:
Ursula Braun <ubraun@linux.ibm.com> Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
-
Guvenc Gulce authored
When the netlink messages to be sent to the userspace are too big for a single netlink message, send them in chunks using the netlink_dump infrastructure. Modify the smc diag dump code so that it can signal to the netlink_dump infrastructure that it needs to send more data. Signed-off-by:
Guvenc Gulce <guvenc@linux.ibm.com> Signed-off-by:
-
Guvenc Gulce authored
arch/s390/net/pnet.c uses ccwgroup function dev_is_ccwgroup() in pnetid_by_dev_port(). For s390 the net/smc code makes use of function pnetid_by_dev_port(). Make sure ccwgroup is built into the kernel, if smc is to be built into the kernel. Signed-off-by:
-
Ursula Braun authored
smc_lgr_cleanup_early() schedules the free worker with delay. DMB unregistering occurs in this delayed worker increasing the risk to reach the SMCD SBA limit without need. Terminate the linkgroup immediately, since termination means early DMB unregistering. For SMCD the global smc_server_lgr_pending lock is given up early. A linkgroup to be given up with smc_lgr_cleanup_early() may already contain more than one connection. Using __smc_lgr_terminate() in smc_lgr_cleanup_early() covers this. And consolidate smc_ism_put_vlan() and smc_put_device() into smc_lgr_free() only. Signed-off-by:
-
Ursula Braun authored
smc_listen_work() contains already an smc_listen_decline() exit. Use this exit for smc_listen_rdma_finish() problems as well. Signed-off-by:
-
Ursula Braun authored
Move check whether peer can be reached into smc_pnet_find_ism_by_pnetid(). Thus searching continues for another ism device, if check fails. Signed-off-by:
-
Ursula Braun authored
smc_clc_send_accept() and smc_clc_send_confirm() are quite similar. Move common code into a separate function smc_clc_send_confirm_accept(). And introduce separate SMCD and SMCR struct definitions for CLC accept resp. confirm. No functional change. Signed-off-by:
-
Ursula Braun authored
Reduce stack size for smc_listen_work() and smc_clc_send_proposal() by dynamic allocation of the CLC buffer to be received or sent. Signed-off-by:
-
Ursula Braun authored
Field names "srv_first_contact" and "cln_first_contact" are misleading, since they apply to both, server and client. Rename them to "first_contact_peer" and "first_contact_local". Rename "ism_gid" by the more precise name "ism_peer_gid". Rename version constant "SMC_CLC_V1" into "SMC_V1". No functional change. Signed-off-by:
-
Ursula Braun authored
SMC starts a separate tcp_listen worker for every SMC socket in state SMC_LISTEN, and can accept an incoming connection request only, if this worker is really running and waiting in kernel_accept(). But the number of running workers is limited. This patch reworks the listening SMC code and starts a tcp_listen worker after the SYN-ACK handshake on the internal clc-socket only. Suggested-by:
-
David S. Miller authored
Krzysztof Kozlowski says: ==================== nfc: s3fwrn5: Few cleanups Changes since v2: 1. Fix dtschema ID after rename (patch 1/8). 2. Apply patch 9/9 (defconfig change). Changes since v1: 1. Rename dtschema file and add additionalProperties:false, as Rob suggested, 2. Add Marek's tested-by, 3. New patches: #4, #5, #6, #7 and #9. ==================== Signed-off-by: -
Krzysztof Kozlowski authored
Since "s3fwrn5" is not a valid vendor prefix, use new GPIO properties instead of the deprecated. Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Tested-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
Krzysztof Kozlowski authored
Robert Bałdyga's email does not work (bounces) since 2016 so remove it. Additionally there are no review/ack/tested tags from Krzysztof Opasiak so it looks like the driver is not supported. As a maintainer of Samsung ARM/ARM64 SoC, I can take care about this driver and provide some review. However clearly driver is not in supported mode as I do not work in Samsung anymore. Signed-off-by:
-
Krzysztof Kozlowski authored
Two functions accept pointer to struct s3fwrn5_fw_info but do not modify the contents. Make them const so the code is a little bit safer. Signed-off-by:
-
Krzysztof Kozlowski authored
The driver uses crypto hash functions so it needs to select CRYPTO_HASH. This fixes build errors: arc-linux-ld: drivers/nfc/s3fwrn5/firmware.o: in function `s3fwrn5_fw_download': firmware.c:(.text+0x152): undefined reference to `crypto_alloc_shash' Signed-off-by:
-
Krzysztof Kozlowski authored
The local variable 'ret' can be removed: drivers/nfc/s3fwrn5/i2c.c:167:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable] Signed-off-by:
-
Krzysztof Kozlowski authored
The device tree property prefix describes the vendor, which in case of S3FWRN5 chip is Samsung. Therefore the "s3fwrn5" prefix for "en-gpios" and "fw-gpios" is not correct and should be deprecated. Introduce properly named properties for these GPIOs but still support deprecated ones. Signed-off-by:
-
Krzysztof Kozlowski authored
The device tree property prefix describes the vendor, which in case of S3FWRN5 chip is Samsung. Therefore the "s3fwrn5" prefix for "en-gpios" and "fw-gpios" is not correct and should be deprecated. Introduce properly named properties for these GPIOs and rename the fw-gpios" to "wake-gpios" to better describe its purpose. Signed-off-by:
-
Krzysztof Kozlowski authored
Convert the Samsung S3FWRN5 NCI NFC controller bindings to dtschema. This is conversion only so it includes properties with invalid prefixes (s3fwrn5,en-gpios) which should be addressed later. Signed-off-by:
-
David S. Miller authored
Wang Hai says: ==================== Fix some kernel-doc warnings for hns. ==================== Signed-off-by: -
Wang Hai authored
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/huawei/hinic/hinic_hw_eqs.c:115: warning: Excess function parameter 'hw_handler' description in 'hinic_aeq_register_hw_cb' Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Wang Hai <wanghai38@huawei.com> Signed-off-by:
-
Wang Hai authored
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/huawei/hinic/hinic_hw_api_cmd.c:382: warning: Excess function parameter 'size' description in 'api_cmd' Reported-by:
-
Wang Hai authored
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/hisilicon/hns/hns_enet.c:1841: warning: Excess function parameter 'netdev' description in 'hns_set_multicast_list' drivers/net/ethernet/hisilicon/hns/hns_enet.c:1841: warning: Excess function parameter 'p' description in 'hns_set_multicast_list' Reported-by:
-
Wang Hai authored
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c:137: warning: Excess function parameter 'drv' description in 'hns_xgmac_enable' drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c:497: warning: Excess function parameter 'cmd' description in 'hns_xgmac_get_regs' Reported-by:
-
Wang Hai authored
Rename cdev to hdev. Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/hisilicon/hns/hnae.c:444: warning: Excess function parameter 'cdev' description in 'hnae_ae_unregister' Reported-by:
-
Wang Hai authored
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/huawei/hinic/hinic_hw_io.c:373: warning: Excess function parameter 'sq_msix_entry' description in 'hinic_io_create_qps' drivers/net/ethernet/huawei/hinic/hinic_hw_io.c:373: warning: Excess function parameter 'rq_msix_entry' description in 'hinic_io_create_qps' Rename these wrong names. Reported-by:
-
