Commits · 4354e188121d92c28647146b70a8c303b46a7dcd · nexedi / linux

19 Apr, 2008 30 commits

[ARM] pxa: remove keypad register definitions from pxa-regs.h · 4354e188

eric miao authored Feb 22, 2008

Keypad registers are now fully defined within pxa27x-keypad.c, no
need to keep those definitions in pxa-regs.h
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

4354e188

[ARM] pxa: add keypad support for littleton · 5fa41510

eric miao authored Jan 23, 2008

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

5fa41510

[ARM] pxa: add keypad support for zylonite · 468e086f

eric miao authored Jan 23, 2008

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

468e086f

[ARM] pxa: add partial keypad support for mainstone · 55c26e40

eric miao authored Jan 23, 2008

This is partial because mainstone's keypad is really special, some of
the keys like '1', '2', ... are actually connected to two row/column
juntions, thus pressing '1' is equivalent to pressing 'A' & 'H'.

This is really brain damanged since it makes distinguishing between
pressing '1' and multiple keys pressing of 'A' & 'H' difficult.

So these special keys are not supported for the time being.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

55c26e40

[ARM] pxa: add pxa27x_keypad device and pxa_set_keypad_info() · 37320980

eric miao authored Jan 23, 2008

also update the clk definitions in pxa27x and pxa3xx.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

37320980

[ARM] pxa: use gpio_keys.c to support mainstone's wakeup switch of GPIO1 · 450d2874

eric miao authored Mar 11, 2008

NOTE: currently don't know if the key code of KEY_SUSPEND is fit for
such usage.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

450d2874

[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x} · c0a596d6

eric miao authored Mar 11, 2008

Changes include:

1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate
   the board capability of this pin to wakeup the system

2. add gpio_set_wake() and keypad_set_wake() to allow dynamically
   enable/disable wakeup from GPIOs and keypad GPIO

   * these functions are currently kept in mfp-pxa2xx.c due to their
     dependency to the MFP configuration

3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP
   is set on incorrect pins

So that the GPIO's wakeup capability is now decided by the following:

   a) processor's capability: (only those GPIOs which have dedicated
      bits within PWER/PRER/PFER can wakeup the system), this is
      initialized by pxa{25x,27x}_init_mfp()

   b) board design decides:
      - whether the pin is designed to wakeup the system (some of
        the GPIOs are configured as other functions, which is not
        intended to be a wakeup source), by OR'ing the pin config
        with MFP_LPM_CAN_WAKEUP

      - which edge the pin is designed to wakeup the system, this
        may depends on external peripherals/connections, which is
        totally board specific; this is indicated by MFP_LPM_EDGE_*

   c) the corresponding device's (most likely the gpio_keys.c) wakeup
      attribute:
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

c0a596d6

[ARM] pxa: use new pin configuration mechanism for lubbock · 9b02b2df

eric miao authored Feb 13, 2008

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

9b02b2df

[ARM] pxa: use new pin configuration mechanism for mainstone · fef06d27

eric miao authored Feb 04, 2008

1. the following code to configure PGSRx is no way portable and
   intuitive:

-	PGSR0 = 0x00008800;
-       PGSR1 = 0x00000002;
-       PGSR2 = 0x0001FC00;
-       PGSR3 = 0x00001F81;

   this is removed as low power state has already been encoded in
   the pin configuration definitions.

   Note: there is no specific reason for some of the GPIOs to drive
   high in low power mode as indicated by the above setting, those
   bits are ignored, and the result is validated to work.

2. the following code to configure GPIO wakeup is removed as this
   is now totally handled by pxa2xx_mfp_config():

-       PWER  = 0xC0000002;
-       PRER  = 0x00000002;
-       PFER  = 0x00000002;
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

fef06d27

[ARM] pxa: move ARRAY_AND_SIZE definition to generic.h · 3d3934c3

eric miao authored Feb 03, 2008

for use by other platforms
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

3d3934c3

[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} · 7facc2f9

eric miao authored Mar 05, 2008

Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs.  A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.

A pin configuration on pxa{25x,27x} is composed of:

    - alternate function selection (or pin mux as commonly called)
    - low power state or sleep state
    - wakeup enabling from low power mode

The following MFP_xxx bit definitions in mfp.h are re-used:

    - MFP_PIN(x)
    - MFP_AFx
    - MFP_LPM_DRIVE_{LOW, HIGH}
    - MFP_LPM_EDGE_*

Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:

    - MFP_CFG_IN  : for input alternate functions
    - MFP_CFG_OUT : for output alternate functions

Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT().  As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.

Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output.  The actual
direction of the GPIO is configured by gpio_direction_{input, output}

Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.

E.g.  invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:

    enable_irq_wake( gpio_to_irq(35) );

To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).

Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:

    - MFP_LPM_WAKEUP_ENABLE

The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:

    - WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
    - WAKEUP_ON_LEVEL_HIGH

The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.

These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.

The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

7facc2f9

[ARM] pxa: separate GPIOs and their mode definitions to pxa2xx-gpio.h · a683b14d

eric miao authored Mar 03, 2008

two reasons:
1. GPIO namings and their mode definitions are conceptually not part
   of the PXA register definitions

2. this is actually a temporary move in the transition of PXA2xx to
   use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
   code will still work and new code can be added in step by step
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

a683b14d

[ARM] pxa: move mfp sysdev registeration out for suspend/resume order · 4be35e23

eric miao authored Feb 04, 2008

MFP configurations after resume should be done before the GPIO registers
are restored. Move the mfp sysdev registeration to the same place where
GPIO and IRQ sysdev(s) are registered to better control the order.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

4be35e23

[ARM] pxa: rename mfp.c to mfp-pxa3xx.c to indicate it's pxa3xx specific · 06b2666e
eric miao authored Mar 03, 2008
```
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
```
06b2666e

[ARM] pxa: make pxa_gpio_irq_type() processor generic · 689c04a3