From: Will Schmidt <willschm@us.ibm.com>

This patch includes updates and cleanup for the PPC64 proc/lparcfg interface.
     - use seq_file's seq_printf for output
     - remove redundant e2a function. (use viopath.c's instead)
     - change to Kconfig to allow building as a module.
     - export required symbols from LparData.c

    Pass # 2 updates..
      - Per Pauls request I've removed the vpurr references, and left
	just a stub function get_purr().
      - this should apply clean to latest linus tree.  (test-applied against
	2.6.7-rc3).

    Pass # 3 updates...
      - Correcting my previously incorrect description of the
	lparcfg_count_active_processors() function..
	This is for the cases where we have some number of virtual
	processors that are different than the total number of threads
	in the system.  (i.e. systemcfg->processorcount isnt the desired
	value for partition_active_processors)
      - moved e2a function into its own file in arch/ppc64/lib.
      - changed lparcfg_count_active_processors() to use a while loop
	instead of a for loop.
      - removed redundant of_node_put in lparcfg_count_active_processors().
      - removed unneeded parms from get-system-parameter rtas_call.
Signed-off-by: Will Schmidt <willschm@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

On recent pSeries systems, EEH needs to be enabled even on PCI Host Bridges
(PHB's).  If not enabled, then ordinary PCI probing (config-space
reads/writes to the bridges) will generate firmware error messages,
possibly a very large number of messages for systems with large numbers of
pci slots.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch fixes some unbalanced usage of pci_dev_get()/pci_dev_put() calls
in the eeh code.  The old code had too many calls to dev_put, which could
cause memory structs to be freed prematurely, possibly leading to bad bad
pointer derefs in certain cases.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

gcc 3.5 is complaining about the size of copy_from_user.  It turns out it
is rather large and putting it out of line saves us about 30kB on a default
kernel build.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Here is a patch to fix some bugs with the current CPM UART code, Tom Rini
has seen this and ok'd it.

* Fixes need to config both SMC1 & SCC1
* Fixes buffer descriptor wrapping issue in set_termios
* Fixes confusion in Kconfig regarding CPM1 vs CPM2
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Pantelis Antoniou <panto@intracom.gr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

We have something like this in our kernel since many months.  It sets the
console device to what OF uses.  ppc64 does the same, and it works ok.
serial is found on CHRP, ch-a is used on all powermacs.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The patch fixes locking of i_flags.  It removes S_QUOTA flag from i_flags
because it was almost unused and updating it on some places correctly
(under i_sem) would be tricky.  Note that accessing of S_NOQUOTA flag is
serialized by dqptr_sem and so we can reliably tested without i_sem.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

- Setup synchronous expansion card resource.
- Fix order of IRQ and FIQ mask/offsets.

This include isn't required for ARM builds either.

Apparantly, the reason for this change is that it gives "much less
NFS stalls with a SMC91C96 on a 10/100MB switch."

Alan Cox's comments on this is:
"spec says 16 collision retries max _ever_.  I bet his 'broken
switch' is a case of half v full duplex" and a recommendation to
remove it.

Also, since the change does not limit the number of times we may
retry to send the packet, I think this code opens a potential DoS
attack against network which has a machine connected running this
code.

Patch from John Lenz

Cleanup and forward port of patch 1849.
This patch provides support for the SHARP LoCoMo device, 
a companion chip similar to the sa1111 device.  It is present
in many of the SHARP Zaurus line of PDAs.

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Patch from Ian Campbell

Update 1954/1 to use pxa2xx- as the platform device prefix 
instead of pxa2xx_. This changes pxamci to pxa2xx-mci, pxa2xx_udc 
to pxa2xx-udc and pxafb to pxa2xx-fb. pxa2xx-uart doesn't need changing.

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into ppc970.osdl.org:/home/torvalds/v2.6/linux

hm, I had a brainfart here.  The recent "fix" to snd_ctl_read() actually
unfixed it.  Revert that, and fix the real bug.

Cc: Jaroslav Kysela <perex@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

There was a memory leak in epoll.

The reference count (d_count) of the struct dentry of a new epoll-fd was
set to TWO.  (new_inode() assigned ONE, than ep_getfd() incremented it by
dget()).  There was only ONE reference to this dentry, so struct dentry and
struct inode were never freed.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

From: Alexey Dobriyan <adobriyan@mail.ru>

drivers/char/upd4990a.c was removed from 2.6.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

From: Michael Geng <linux@MichaelGeng.de>

The patch updates docs, comments + strings to also mention the SAA5281 chip
(which is compatible to the SAA5246A) as supported.
Signed-off-by: Michael Geng <linux@MichaelGeng.de>
Signed-off-by: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

  CHECK   fs/smbfs/smbiod.c
fs/smbfs/smbiod.c:68:25: warning: non-ANSI parameter list
  CHECK   drivers/isdn/tpam/tpam_crcpc.c
drivers/isdn/tpam/tpam_crcpc.c:57:15: warning: non-ANSI parameter list
  CHECK   drivers/scsi/aic7xxx/aic79xx_reg_print.c
drivers/scsi/aic7xxx/aic79xx_osm.h:791:19: warning: non-ANSI parameter list
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Move the memory policy freeing to later in exit to make sure the last
memory allocations don't use an uninitialized policy.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch sets the correct capabilities flag for vesafb and vga16fb to
provide fbcon with the correct hints as to the best scrolling mode.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Added a new scrolling mode (SCROLL_PAN_REDRAW) to fbcon that should greatly
benefit unaccelerated drivers such as VESA fbdev.  An increase of 3-10 times
in scrolling speed can be expected.

Currently, fbcon has 4 different scrolling methods (1-4).  Potentially, we can
have 6.  This patch implements SCROLL_PAN_REDRAW (5).  SCROLL_WRAP_REDRAW (6)
is still unimplemented.

Scroll Mode		Operation	YPan	YWrap
+++++++++++++++++++++++++++++++++++++++++++++++++++++
1. SCROLL_ACCEL		copyarea	No	No
2. SCROLL_REDRAW	imageblit	No	No
3. SCROLL_PAN		copyarea	Yes	No
4. SCROLL_WRAP		copyarea	No	Yes
5. SCROLL_PAN_REDRAW 	imageblit	Yes	No	
6. SCROLL_WRAP_REDRAW	imageblit	No	Yes
+++++++++++++++++++++++++++++++++++++++++++++++++++++
Note 1:  I've changed the nomenclature to increase clarity:

SCROLL_ACCEL = SCROLL_MOVE
SCROLL_REDRAW = SCROLL_REDRAW
SCROLL_PAN = SCROLL_PAN_MOVE
SCROLL_WRAP = SCROLL_WRAP_MOVE

To demonstrate the effect of each of the scrolling methods on
an unaccelerated PCI/AGP-based driver (vesafb), I used a simple
benchmark (time cat linux/MAINTAINERS - a 50K text file). The
framebuffer is set at:

1024x768-8bpp, 8x16 font, yres_virtual = 2*yres

1. SCROLL_MOVE:
real    5m50.277s
user    0m0.001s
sys     5m50.227s

Almost 6 minutes for a 50K text file.  Using soft copyarea on a
PCI-based card is just too slow (because copyarea has to 
read from the framebuffer memory).

2. SCROLL_PAN_MOVE
scrollmode: SCROLL_PAN
real    0m8.592s
user    0m0.000s
sys     0m8.586s

Using ypan with copyarea dramatically improves the scrolling.  However, the
scrolling action is jerky (fast during the panning stages, slows down during
the copyarea stages).

3. SCROLL_REDRAW (this is the default scrolling mode)
real    0m3.189s
user    0m0.000s
sys     0m3.170s

Simply eliminating the copyarea, even without ypanning, makes it faster than
SCROLL_PAN_MOvE.  Plus, the scrolling action is smoother.

So, if we combine YPanning with imageblit (PAN_REDRAW), we get this:

4. SCROLL_PAN_REDRAW
real    0m0.520s
user    0m0.000s
sys     0m0.518s

That's almost 6x faster than SCROLL_REDRAW.  Increasing the amount of video
RAM still increases the speed, but not very dramatically.  Higher than 16 MB,
the increase is negligible.

Using an accelerated driver, we see almost the same effect but not as
dramatically:

1. SCROLL_MOVE - accel
real    0m3.112s
user    0m0.000s
sys     0m3.112s

2. SCROLL_REDRAW - accel
real    0m2.604s
user    0m0.000s
sys     0m2.603s

Redraw is still faster than move, but not much.

3. SCROLL_PAN_MOVE - accel
real    0m0.203s
user    0m0.000s
sys     0m0.202s

4. SCROLL_PAN_REDRAW - accel
real    0m0.326s
user    0m0.002s
sys     0m0.323s

This is one exception.  If panning is enabled, move is actually faster than
redraw.  As to why, I don't know.

So based on the above, fbcon will choose the scrolling method based on the
following preference:

Ypan/Ywrap > accel imageblit > accel copyarea >
soft imageblit > (soft copyarea)

Note 2: Exception: accel copyarea > accel imageblit if Pan/Wrap is enabled.

Note 3: soft copyarea will be avoided by fbcon as much as possible unless
there is a specific override, ie., FBINFO_READS_FAST flag is set.  If this
flag is set, fbcon will prefer copyarea over imageblit, accel or soft.

As a final note, in order for fbcon to use the best scrolling method, the
low-level drivers must provide the correct hinting by setting the
FBINFO_HWACCEL_* flags.

To vesafb users: boot vesafb like this for fastest scrolling action:

video=vesafb:ypan,vram:16
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

1.  From Petr Vandrovec <vandrove@vc.cvut.cz>.

Begin quote

        yesterday I finally found why 2.6.x has problems with taking
        over vgacon.  Problem is that take_over_console does:

  	if (IS_VISIBLE)
    	save_screen(i);
  	...
  	visual_init(i, 0);
  	...

        so code nicely saves screen contents, and calls visual_init,
        which calls fbcon's init, which in turn can issue vc_resize.  And this
        vc_resize will trigger read from vc->vc_origin.  But vc_origin still
        points to videomemory, not to the buffer where save_screen() copied
        its data.

End quote

So updating vc->vc_origin to point to screenbuf after the previous console
deinitializes allows fbcon to correctly update the screen from the screen
buffer.  This change makes the clearing of vram (using fillrect) unnecessary.

2.  If FBINFO_MISC_MODESWITCH flag is set in info, do the set_par() in
fbcon_switch() instead of piggy-backing the set_par() on fbcon_resize().  This
preserves the current var, skipping the unnecessary fb_find_mode() step.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Ugly workaround.  When switching from KD_GRAPHICS to KD_TEXT, the event is
captured at fbcon_blank() allowing fbcon to reinitialize the hardware.
However, some hardware requires the reinitialization to be done
immediately, others require it to be done later.  Others may need it to be
done immediately and later, this is the worst case.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

From: Ursula Braun-Krahl <braunu@de.ibm.com>
From: Heiko Carstens <heiko.carstens@de.ibm.com>
From: Gerald Schaefer <geraldsc@de.ibm.com>
From: Martin Schwidefsky <schwidefsky@de.ibm.com>

Add s390 architecture support for cpu hotplug.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch introduces a notifier chain for cpu idle.  There are two events
CPU_IDLE and CPU_NOT_IDLE that are called just before the cpu goes to sleep
and right after the cpu woke up again.  The notifier is used to simplify the
no-hz-timer-in-idle feature and the virtual cpu timers.  In addition the
virtual cpu timer functions have been moved to arch/s390/kernel/vtime.c, which
gives a nice separation between the timer functions related to real time and
the timer functions related to virtual cpu time.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

From: Peter Tiedemann <ptiedem@de.ibm.com>

ctc driver changes:
 - Make use of the debug feature to ease debugging.
 - ctctty: use dev_alloc_name to allocate a network device name.
 - ctctty: avoid deadlock of ctc_tty_close vs ctc_tty_flush_buffer.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

From: Arnd Bergmann <arndb@de.ibm.com>

Common i/o layer changes:
 - Reorder checking and setting of the ccw device id.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

From: Horst Hummel <horst.hummel@de.ibm.com>

dasd device driver changes:
 - Set and check the retry counter in start_IO for all requests.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Setting it to inet_accept causes UDP accept attempts
to OOPS.  In particular, accept01 from LTP tries this.
Signed-off-by: David S. Miller <davem@redhat.com>

This version does not change user visible structures.
Signed-off-by: Jamal Hadi Salim <hadi@znyx.com>
Signed-off-by: David S. Miller <davem@redhat.com>

- rtnetlink.h needs including
- optimize loss test so that net_random() call is not done
  when no-loss is indicated
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@redhat.com>