During close, all of the MAC filters are cleared, so the driver would be
unable to receive unicast packets after being closed and reopened.

Add the adapter's "hardware" MAC address filter in open, not init. This
ensures that the correct filter is present each time.

Change-ID: I51a11e9c1200139dab6f66a5353bd38c7d26f875
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to an inverted conditional, the driver was marking all of its MAC
filters for deletion every time set_rx_mode was called. Depending upon
the timing of the calls to set_rx_mode and the processing of the admin
queue, the driver would (accidentally) end up with a varying number of
functional filters.

Correct this logic so that MAC filters are added and removed correctly.
Add a check for the driver's "hardware" MAC address so that this filter
doesn't get removed incorrectly.

Change-ID: Ib3e7c4a5b53df6835f164fe44cb778cb71f8aff8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When a VF is disabled, there is no way for it to recover until either
the PF driver is reloaded or SR-IOV is disabled and enabled. To correct
this, enable the VF after a successful reset.

Change-ID: I9e0788476c4d53d5407961b503febdfff2b8a7c6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The VF disable code was just whanging on the reset bit without properly
cleaning up the VF, which would leave the VF in an indeterminate state
from which it could not recover. Fix this by notifying the VF and then
by calling the normal VF reset routine.

Change-ID: I862b9dfa919368773cbdc212b805b520db2f7430
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

MAC filters for VFs were being programmed with 0 for the VLAN value when
there was no VLAN assigned. This is incorrect and actually assigns the
VF to VLAN 0. Instead, we must use -1 to indicate that no VLAN is in
use. This change programs the filters correctly and gets rid of a bogus
error message when setting a port VLAN on an active VF.

Change-ID: Ica9a9906d768405377ff3308e27f7d0b5b2ea96e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Make the necessary updates to i40e_adminq_cmd.h.

Change-ID: Ib031c86cc6cab78e5aa44c64d8ce5474be8d7e42
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes some #ifdef's that should not be there. They
were stopping code that is needed from being compiled in.

With these #ifdef's removed, changes are needed in the driver
to fix some compile errors: adding missing parameters to
the definition of ndo_bridge_setlink and a ndo_dflt_brige_getlink call.

Change-ID: I5516614e1bc50b6bca0647cef971bc96161ba2de
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If user attempts to set a port VLAN on a VF that already has the same
port VLAN configured, the driver will go through a completely
unnecessary flurry of filter removals and filter adds. Just check for
this condition and return success instead of doing a bunch of busywork.

Change-ID: Ia1a9e83e6ed48b3f4658bc20dfc6af0cf525d54a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver currently only maps TX and RX queues to a single MSI-X vector
per queue pair if there are exactly enough vectors for this.
Unfortunately, if we have too many vectors it will fail and allocate
queues to vectors in a suboptimal manner. Change the condition check to
allow for excess vectors. In this case, the extras just won't be used.

Change-ID: I23e1e2955c64739c86612db88a25583e6a7e0b17
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a prefetch for the next Tx descriptor to be used when we know
there are more coming.

Change-ID: Ibb9acab11d508eec2db7da795df74debc16eeacb
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The Flex10 device/function capability has been upgraded to include
information needed to support Flex-10 configurations. This patch adds new
fields to the i40e_hw_capabilities structure and updates
i40e_parse_discover_capabilities functions to extract them from the AQ
response. Naming convention has changed to use flex10 mode instead of
existing mfp_mode_1.

Change-ID: I305dd888866985a30293acb3fb14fa43ca6b79ea
Signed-off-by: Pawel Orlowski <pawel.orlowski@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since the driver can dynamically enable/disable FD ATR and SB features,
these stats help keep track of the current state and along with
fd_flush count provide a means to debug what could be going on
with the flow director filters. This will take away the need for
being verbose in our debug logs with respect to FD.

Change-ID: I29224f750fe6602391043655d18996570720377d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e supports UDP tunnel headers up to 80 bytes in length, so
this adds a check to ensure that it doesn't try to offload
packets that exceed that.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Some of the local variable intializers in the driver turned out to be pointless,
kill them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/bridge/br_mdb.c

Minor conflict in br_mdb.c, in 'net' we added a memset of the
on-stack 'ip' variable whereas in 'net-next' we assign a new
member 'vid'.
Signed-off-by: David S. Miller <davem@davemloft.net>

Until now all user mdb entries were added in vlan 0, this patch adds
support to allow the user to specify the vlan for the entry.
About the uapi change a hole in struct br_mdb_entry is used so the size
and offsets are kept the same (verified with pahole and tested with older
iproute2).

Example:
$ bridge mdb
dev br0 port eth1 grp 239.0.0.1 permanent vlan 2000
dev br0 port eth1 grp 239.0.0.1 permanent vlan 200
dev br0 port eth1 grp 239.0.0.1 permanent
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ARG1 = BPF_R1 as it stands, evaluates to regs[BPF_REG_1] = regs[BPF_REG_1]
and thus has no effect. Add a comment instead, explaining what happens and
why it's okay to just remove it. Since from user space side, a tail call is
invoked as a pseudo helper function via bpf_tail_call_proto, the verifier
checks the arguments just like with any other helper function and makes
sure that the first argument (regs[BPF_REG_1])'s type is ARG_PTR_TO_CTX.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes the default to build IPv6 into the kernel. IPv6
now has significant traction and any remaining vestiges of IPv6
not being provided parity with IPv4 should be swept away. IPv6 is now
core to the Internet and kernel.

Points on IPv6 adoption:

- Per Google statistics, IPv6 usage has reached 7% on the Internet
  and continues to exhibit an exponential growth rate
  https://www.google.com/intl/en/ipv6/statistics.html
- Just a few days ago ARIN officially depleted its IPv4 pool
- IPv6 only data centers are being successfully built
  (e.g. at Facebook)

This patch changes the IPv6 Kconfig for IPV6. Default for CONFIG_IPV6
is set to "y" and the text has been updated to reflect the maturity of
IPv6.

Impact:

Under some circumstances building modules in to kernel might have a
performance advantage. In my testing, I did notice a very slight
improvement.

This will obviously increase the size of the kernel image. In my
configuration I see:

IPv6 as module:

   text    data     bss     dec     hex filename
9703666 1899288  933888 12536842         bf4c0a vmlinux

IPv6 built into kernel

  text     data     bss     dec     hex filename
9436490 1879600  913408 12229498         ba9b7a vmlinux

Which increases text size by ~270K (2.8% increase in size for me). If
image size is an issue, presumably for a device which does not do IP
networking (IMO we should be discouraging IPv4-only devices), IPV6 can
be disabled or still built as a module.
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Missing list head init in bluetooth hidp session creation, from Tedd
    Ho-Jeong An.

 2) Don't leak SKB in bridge netfilter error paths, from Florian
    Westphal.

 3) ipv6 netdevice private leak in netfilter bridging, fixed by Julien
    Grall.

 4) Fix regression in IP over hamradio bpq encapsulation, from Ralf
    Baechle.

 5) Fix race between rhashtable resize events and table walks, from Phil
    Sutter.

 6) Missing validation of IFLA_VF_INFO netlink attributes, fix from
    Daniel Borkmann.

 7) Missing security layer socket state initialization in tipc code,
    from Stephen Smalley.

 8) Fix shared IRQ handling in boomerang 3c59x interrupt handler, from
    Denys Vlasenko.

 9) Missing minor_idr destroy on module unload on macvtap driver, from
    Johannes Thumshirn.

10) Various pktgen kernel thread races, from Oleg Nesterov.

11) Fix races that can cause packets to be processed in the backlog even
    after a device attached to that SKB has been fully unregistered.
    From Julian Anastasov.

12) bcmgenet driver doesn't account packet drops vs.  errors properly,
    fix from Petri Gynther.

13) Array index validation and off by one fix in DSA layer from Florian
    Fainelli

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (66 commits)
  can: replace timestamp as unique skb attribute
  ARM: dts: dra7x-evm: Prevent glitch on DCAN1 pinmux
  can: c_can: Fix default pinmux glitch at init
  can: rcar_can: unify error messages
  can: rcar_can: print request_irq() error code
  can: rcar_can: fix typo in error message
  can: rcar_can: print signed IRQ #
  can: rcar_can: fix IRQ check
  net: dsa: Fix off-by-one in switch address parsing
  net: dsa: Test array index before use
  net: switchdev: don't abort unsupported operations
  net: bcmgenet: fix accounting of packet drops vs errors
  cdc_ncm: update specs URL
  Doc: z8530book: Fix typo in API-z8530-sync-txdma-open.html
  net: inet_diag: always export IPV6_V6ONLY sockopt for listening sockets
  bridge: mdb: allow the user to delete mdb entry if there's a querier
  net: call rcu_read_lock early in process_backlog
  net: do not process device backlog during unregistration
  bridge: fix potential crash in __netdev_pick_tx()
  net: axienet: Fix devm_ioremap_resource return value check
  ...

Pull crypto fixes from Herbert Xu:
 "This fixes a duplicate dma_unmap_sg call in omap-des and reentrancy
  bugs in the powerpc nx driver which may cause bogus output or worse
  memory corruption"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: nx - Fix reentrancy bugs
  crypto: omap-des - Fix unmapping of dma channels

Merge tag 'linux-can-fixes-for-4.2-20150712' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2015-07-12

this is a pull request of 8 patchs for net/master.

Sergei Shtylyov contributes 5 patches for the rcar_can driver, fixing the IRQ
check and several info and error messages. There are two patches by J.D.
Schroeder and Roger Quadros for the c_can driver and dra7x-evm device tree,
which precent a glitch in the DCAN1 pinmux. Oliver Hartkopp provides a better
approach to make the CAN skbs unique, the timestamp is replaced by a counter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit dec4f799.

Jörg Otte reports a NULL pointder dereference due to this commit, as
'crtc_state' very much can be NULL:

        crtc_state = state->base.state ?
                intel_atomic_get_crtc_state(state->base.state, intel_crtc) : NULL;

So the change to test 'crtc_state->base.active' cannot possibly be
correct as-is.

There may be some other minimal fix (like just checking crtc_state for
NULL), but I'm just reverting it now for the rc2 release, and people
like Daniel Vetter who actually know this code will figure out what the
right solution is in the longer term.
Reported-and-bisected-by: Jörg Otte <jrg.otte@gmail.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull VFS fixes from Al Viro:
 "Fixes for this cycle regression in overlayfs and a couple of
  long-standing (== all the way back to 2.6.12, at least) bugs"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  freeing unlinked file indefinitely delayed
  fix a braino in ovl_d_select_inode()
  9p: don't leave a half-initialized inode sitting around

Pull MIPS fixes from Ralf Baechle:
 "A fair number of 4.2 fixes also because Markos opened the flood gates.

   - Patch up the math used calculate the location for the page bitmap.

   - The FDC (Not what you think, FDC stands for Fast Debug Channel) IRQ
     around was causing issues on non-Malta platforms, so move the code
     to a Malta specific location.

   - A spelling fix replicated through several files.

   - Fix to the emulation of an R2 instruction for R6 cores.

   - Fix the JR emulation for R6.

   - Further patching of mindless 64 bit issues.

   - Ensure the kernel won't crash on CPUs with L2 caches with >= 8
     ways.

   - Use compat_sys_getsockopt for O32 ABI on 64 bit kernels.

   - Fix cache flushing for multithreaded cores.

   - A build fix"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: O32: Use compat_sys_getsockopt.
  MIPS: c-r4k: Extend way_string array
  MIPS: Pistachio: Support CDMM & Fast Debug Channel
  MIPS: Malta: Make GIC FDC IRQ workaround Malta specific
  MIPS: c-r4k: Fix cache flushing for MT cores
  Revert "MIPS: Kconfig: Disable SMP/CPS for 64-bit"
  MIPS: cps-vec: Use macros for various arithmetics and memory operations
  MIPS: kernel: cps-vec: Replace KSEG0 with CKSEG0
  MIPS: kernel: cps-vec: Use ta0-ta3 pseudo-registers for 64-bit
  MIPS: kernel: cps-vec: Replace mips32r2 ISA level with mips64r2
  MIPS: kernel: cps-vec: Replace 'la' macro with PTR_LA
  MIPS: kernel: smp-cps: Fix 64-bit compatibility errors due to pointer casting
  MIPS: Fix erroneous JR emulation for MIPS R6
  MIPS: Fix branch emulation for BLTC and BGEC instructions
  MIPS: kernel: traps: Fix broken indentation
  MIPS: bootmem: Don't use memory holes for page bitmap
  MIPS: O32: Do not handle require 32 bytes from the stack to be readable.
  MIPS, CPUFREQ: Fix spelling of Institute.
  MIPS: Lemote 2F: Fix build caused by recent mass rename.

Commit 514ac99c "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.

Without timestamping to be required by user space applications this timestamp
was not generated which lead to commit 36c01245 "can: fix loss of CAN frames
in raw_rcv" - which forces the timestamp to be set in all CAN related skbuffs
by introducing several __net_timestamp() calls.

This forces e.g. out of tree drivers which are not using alloc_can{,fd}_skb()
to add __net_timestamp() after skbuff creation to prevent the frame loss fixed
in mainline Linux.

This patch removes the timestamp dependency and uses an atomic counter to
create an unique identifier together with the skbuff pointer.

Btw: the new skbcnt element introduced in struct can_skb_priv has to be
initialized with zero in out-of-tree drivers which are not using
alloc_can{,fd}_skb() too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Driver core sets "default" pinmux on on probe and CAN driver
sets "sleep" pinmux during register. This causes a small window
where the CAN pins are in "default" state with the DCAN module
being disabled.

Change the "default" state to be like sleep so this glitch is
avoided. Add a new "active" state that is used by the driver
when CAN is actually active.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The previous change 3973c526 (net: can: c_can: Disable pins when CAN
interface is down) causes a slight glitch on the pinctrl settings when used.
Since commit ab78029e (drivers/pinctrl: grab default handles from device core),
the device core will automatically set the default pins. This causes the pins
to be momentarily set to the default and then to the sleep state in
register_c_can_dev(). By adding an optional "enable" state, boards can set the
default pin state to be disabled and avoid the glitch when the switch from
default to sleep first occurs. If the "enable" state is not available
c_can_pinctrl_select_state() falls back to using the "default" pinctrl state.

[Roger Q] - Forward port to v4.2 and use pinctrl_get_select().
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

All the error messages in the driver but  the ones from devm_clk_get() failures
use similar format.  Make those  two messages consitent with others.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Also print the error code when the request_irq() call fails in rcar_can_open(),
rewording  the error message...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Fix typo in the first error message printed by rcar_can_open().

Based on the original patch by Vladimir Barinov.

Fixes: 862e2b6a ("can: rcar_can: support all input clocks")
Reported-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Printing IRQ # using "%x" and "%u" unsigned formats isn't quite correct as
'ndev->irq' is of  type *int*, so  the "%d" format  needs to be used instead.

While fixing this, beautify the dev_info() message in rcar_can_probe() a bit.

Fixes: fd115931 ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

rcar_can_probe() regards 0 as a wrong IRQ #, despite platform_get_irq() that it
calls returns negative error code in that case. This leads to the following
being printed to the console when attempting to open the device:

error requesting interrupt fffffffa

because  rcar_can_open() calls request_irq() with a negative IRQ #, and that
function naturally fails with -EINVAL.

Check for the negative error codes instead and propagate them upstream instead
of just returning -ENODEV.

Fixes: fd115931 ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Pull x86 fixes from Thomas Gleixner:

 - the high latency PIT detection fix, which slipped through the cracks
   for rc1

 - a regression fix for the early printk mechanism

 - the x86 part to plug irq/vector related hotplug races

 - move the allocation of the espfix pages on cpu hotplug to non atomic
   context.  The current code triggers a might_sleep() warning.

 - a series of KASAN fixes addressing boot crashes and usability

 - a trivial typo fix for Kconfig help text

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/kconfig: Fix typo in the CONFIG_CMDLINE_BOOL help text
  x86/irq: Retrieve irq data after locking irq_desc
  x86/irq: Use proper locking in check_irq_vectors_for_cpu_disable()
  x86/irq: Plug irq vector hotplug race
  x86/earlyprintk: Allow early_printk() to use console style parameters like '115200n8'
  x86/espfix: Init espfix on the boot CPU side
  x86/espfix: Add 'cpu' parameter to init_espfix_ap()
  x86/kasan: Move KASAN_SHADOW_OFFSET to the arch Kconfig
  x86/kasan: Add message about KASAN being initialized
  x86/kasan: Fix boot crash on AMD processors
  x86/kasan: Flush TLBs after switching CR3
  x86/kasan: Fix KASAN shadow region page tables
  x86/init: Clear 'init_level4_pgt' earlier
  x86/tsc: Let high latency PIT fail fast in quick_pit_calibrate()

Pull timer fixes from Thomas Gleixner:
 "This update from the timer departement contains:

   - A series of patches which address a shortcoming in the tick
     broadcast code.

     If the broadcast device is not available or an hrtimer emulated
     broadcast device, some of the original assumptions lead to boot
     failures.  I rather plugged all of the corner cases instead of only
     addressing the issue reported, so the change got a little larger.

     Has been extensivly tested on x86 and arm.

   - Get rid of the last holdouts using do_posix_clock_monotonic_gettime()

   - A regression fix for the imx clocksource driver

   - An update to the new state callbacks mechanism for clockevents.
     This is required to simplify the conversion, which will take place
     in 4.3"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick/broadcast: Prevent NULL pointer dereference
  time: Get rid of do_posix_clock_monotonic_gettime
  cris: Replace do_posix_clock_monotonic_gettime()
  tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build
  tick/broadcast: Handle spurious interrupts gracefully
  tick/broadcast: Check for hrtimer broadcast active early
  tick/broadcast: Return busy when IPI is pending
  tick/broadcast: Return busy if periodic mode and hrtimer broadcast
  tick/broadcast: Move the check for periodic mode inside state handling
  tick/broadcast: Prevent deep idle if no broadcast device available
  tick/broadcast: Make idle check independent from mode and config
  tick/broadcast: Sanity check the shutdown of the local clock_event
  tick/broadcast: Prevent hrtimer recursion
  clockevents: Allow set-state callbacks to be optional
  clocksource/imx: Define clocksource for mx27

Pull irq fix from Thomas Gleixner:
 "A single fix for a cpu hotplug race vs. interrupt descriptors:

  Prevent irq setup/teardown across the cpu starting/dying parts of cpu
  hotplug so that the starting/dying cpu has a stable view of the
  descriptor space.  This has been an issue for all architectures in the
  cpu dying phase, where interrupts are migrated away from the dying
  cpu.  In the starting phase its mostly a x86 issue vs the vector space
  update"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  hotplug: Prevent alloc/free of irq descriptors during cpu up/down

	Normally opening a file, unlinking it and then closing will have
the inode freed upon close() (provided that it's not otherwise busy and
has no remaining links, of course).  However, there's one case where that
does *not* happen.  Namely, if you open it by fhandle with cold dcache,
then unlink() and close().

	In normal case you get d_delete() in unlink(2) notice that dentry
is busy and unhash it; on the final dput() it will be forcibly evicted from
dcache, triggering iput() and inode removal.  In this case, though, we end
up with *two* dentries - disconnected (created by open-by-fhandle) and
regular one (used by unlink()).  The latter will have its reference to inode
dropped just fine, but the former will not - it's considered hashed (it
is on the ->s_anon list), so it will stay around until the memory pressure
will finally do it in.  As the result, we have the final iput() delayed
indefinitely.  It's trivial to reproduce -

void flush_dcache(void)
{
        system("mount -o remount,rw /");
}

static char buf[20 * 1024 * 1024];

main()
{
        int fd;
        union {
                struct file_handle f;
                char buf[MAX_HANDLE_SZ];
        } x;
        int m;

        x.f.handle_bytes = sizeof(x);
        chdir("/root");
        mkdir("foo", 0700);
        fd = open("foo/bar", O_CREAT | O_RDWR, 0600);
        close(fd);
        name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0);
        flush_dcache();
        fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR);
        unlink("foo/bar");
        write(fd, buf, sizeof(buf));
        system("df .");			/* 20Mb eaten */
        close(fd);
        system("df .");			/* should've freed those 20Mb */
        flush_dcache();
        system("df .");			/* should be the same as #2 */
}

will spit out something like
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 303843      1131 100% /
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 303843      1131 100% /
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 283282     21692  93% /
- inode gets freed only when dentry is finally evicted (here we trigger
than by remount; normally it would've happened in response to memory
pressure hell knows when).

Cc: stable@vger.kernel.org # v2.6.38+; earlier ones need s/kill_it/unhash_it/
Acked-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

when opening a directory we want the overlayfs inode, not one from
the topmost layer.
Reported-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Tested-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Cc: stable@vger.kernel.org # all branches
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Florian Fainelli says:

====================
net: dsa: OF parsing fixes

This patch series fixes two small parsing issues, the first one was
reported by Dan, the second came after looking more closely at the
code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>