Wake on WLAN(wowlan) is a feature which allows devices
to be woken up from suspend state through wlan events.

When user enables wowlan feature and then let the device
enter suspend state, wowlan firmware will be loaded by
the driver and periodically monitors wifi packets.
Power consumption of wifi chip will be reduced in this
state.

If wowlan firmware detects that specific wlan event
happens, it will issue wakeup signal to trigger resume
process. Driver will load normal firmware and let wifi
chip return to the original state.

Currently supported wlan events include receiving magic packet,
rekey packet and deauth packet, and disconnecting from AP.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Driver used to download normal firmware only,
but some devices support wowlan and require to
download wowlan firmware when system suspends.
So modify rtw_load_firmware() and its callback to
allow driver to download both normal and wowlan firmware.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Some devices need to configure interface/HCI related reigsters
in power on flow. Add interface_cfg for HCI for the settings.

The driver only supports RTL8822BE/RTL8822CE now, and since
RTL8822BE does not need to configure PCIE, the configuration
is only added for RTL8822CE. Without it, some of the RTL8822CE
device can crash and disconnected to host in suspend/wowlan mode.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When PCI trx rings are reset, the DMA engine should also be reset.
Otherswise, the rx_tag of rx flow is not synchronous to hw.

Remove DMA reset when rtw_pci_start() as we added it in
rtw_pci_setup().
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When skbs queued for each TX ring are relased in PCI stop flow,
the ring index should be reset at the same time.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Clang warns:

../drivers/net/wireless/intersil/hostap/hostap_ap.c:2511:3: warning:
misleading indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
        if (sta->tx_supp_rates & WLAN_RATE_5M5)
        ^
../drivers/net/wireless/intersil/hostap/hostap_ap.c:2509:2: note:
previous statement is here
        if (sta->tx_supp_rates & WLAN_RATE_2M)
        ^
1 warning generated.

This warning occurs because there is a space before the tab on this
line. Remove it so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.

Fixes: ff1d2767 ("Add HostAP wireless driver.")
Link: https://github.com/ClangBuiltLinux/linux/issues/813Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In order to support authentication of equals peers,
need to save RX Broadcast key per peer (on top of 1 TX broadcast key
and unicast key per peer).
Signed-off-by: Maital Hahn <maitalm@ti.com>
Acked-by: Guy Mishol <guym@ti.com>
Signed-off-by: Hari Nagalla <hnagalla@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Remove Nishant Sarmukadam from Maintainer list, as he is no
longer working in NXP.
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Before commit 1e58252e ("mwifiex: Fix heap overflow in
mmwifiex_process_tdls_action_frame()"),
mwifiex_process_tdls_action_frame() already had too many magic numbers.
But this commit just added a ton more, in the name of checking for
buffer overflows. That seems like a really bad idea.

Let's make these magic numbers a little less magic, by
(a) factoring out 'pos[1]' as 'ie_len'
(b) using 'sizeof' on the appropriate source or destination fields where
    possible, instead of bare numbers
(c) dropping redundant checks, per below.

Regarding redundant checks: the beginning of the loop has this:

                if (pos + 2 + pos[1] > end)
                        break;

but then individual 'case's include stuff like this:

 			if (pos > end - 3)
 				return;
 			if (pos[1] != 1)
				return;

Note that the second 'return' (validating the length, pos[1]) combined
with the above condition (ensuring 'pos + 2 + length' doesn't exceed
'end'), makes the first 'return' (whose 'if' can be reworded as 'pos >
end - pos[1] - 2') redundant. Rather than unwind the magic numbers
there, just drop those conditions.

Fixes: 1e58252e ("mwifiex: Fix heap overflow in mmwifiex_process_tdls_action_frame()")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2020-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

First set of patches intended for v5.6

* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;

Use the print_hex_dump_debug() helper, instead of open-coding the same
operations.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Remove unused fields, copied from the Sun LANCE driver eons ago.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Linus Walleij says:

====================
IXP4xx networking cleanups

This is a patch series which jams together Arnds and mine
cleanups for the IXP4xx networking.

I also have patches for device tree support but that
requires more elaborate work, this series is some of
mine and some of Arnds patches that is a good foundation
for his multiplatform work and my device tree work.

These are for application to the networking tree so
that can be taken in one separate sweep.

I have tested the patches for a bit using zeroday builds
and some boots on misc IXP4xx devices and haven't run
into any major problems. We might find some new stuff
as a result from the new compiler coverage.

I had to depromote enabling compiler coverage at one
point in the v2 set because it depended on other patches
making the code more generic.

The change in v3 was simply dropping one offending
patch hardcoding base addresses into the driver.

The change in v4 drops a stable@ tag that was
unnecessary.

This v5 is a rebase of the v4 patch set on top of
net-next.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use the netdevice struct device .parent field when calling
dma_pool_create(): the .dma_coherent_mask and .dma_mask
pertains to the bus device on the hardware (platform)
bus in this case, not the struct device inside the network
device. This makes the pool allocation work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In order to probe this ethernet interface from the device tree
all physical MMIO regions must be passed as resources. Begin
this rewrite by first passing the port base address as a
resource for all platforms using this driver, remap it in
the driver and avoid using any reference of the statically
mapped virtual address in the driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Simplify and correct a bunch of messages using printk
directly to use the netdev_* macros. I have not changed
all of them, just the low-hanging fruit.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use "ndev" for the struct net_device and "dev" for the
struct device in probe() and remove(). Add the local
"dev" pointer for later use in refactoring.

Take this opportunity to fix inverse christmas tree
coding style.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The IXP4xx driver was initializing the MDIO bus before even
probing, in the callbacks supposed to be used for setting up
the module itself, and with the side effect of trying to
register the MDIO bus as soon as this module was loaded or
compiled into the kernel whether the device was discovered
or not.

This does not work with multiplatform environments.

To get rid of this: set up the MDIO bus from the probe()
callback and remove it in the remove() callback. Rename
the probe() and remove() calls to reflect the most common
conventions.

Since there is a bit of checking for the ethernet feature
to be present in the MDIO registering function, making the
whole module not even be registered if we can't find an
MDIO bus, we need something similar: register the MDIO
bus when the corresponding ethernet is probed, and
return -EPROBE_DEFER on the other interfaces until this
happens. If no MDIO bus is present on any of the
registered interfaces we will eventually bail out.

None of the platforms I've seen has e.g. MDIO on EthB
and only uses EthC, there is always a Ethernet hardware
on the NPE (B, C) that has the MDIO bus, we just might
have to wait for it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The platform data is needed to compile the driver as standalone,
so move it to a global location along with similar files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The ixp46x ptp driver has a somewhat unusual setup, where the ptp
driver and the ethernet driver are in different directories but
access the same registers that are defined a platform specific
header file.

Moving everything into drivers/net/ makes it look more like most
other ptp drivers and allows compile-testing this driver on
other targets.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The ixp4xx_hss driver needs the platform data definition and the
system clock rate to be compiled. Move both into a new platform_data
header file.

This is a prerequisite for compile testing, but turning on compile
testing requires further patches to isolate the SoC headers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Change the driver to use portable integer types to avoid
warnings during compile testing:

drivers/net/wan/ixp4xx_hss.c:863:21: error: cast to 'u32 *' (aka 'unsigned int *') from smaller integer type 'int' [-Werror,-Wint-to-pointer-cast]
        memcpy_swab32(mem, (u32 *)((int)skb->data & ~3), bytes / 4);
                           ^
drivers/net/wan/ixp4xx_hss.c:979:12: error: incompatible pointer types passing 'u32 *' (aka 'unsigned int *') to parameter of type 'dma_addr_t *' (aka 'unsigned long long *') [-Werror,-Wincompatible-pointer-types]
                                              &port->desc_tab_phys)))
                                              ^~~~~~~~~~~~~~~~~~~~
include/linux/dmapool.h:27:20: note: passing argument to parameter 'handle' here
                     dma_addr_t *handle);
                                 ^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On modern hardware with a large number of cpus and using XDP,
the current MSIX limit is insufficient.  Bump the limit in
order to allow more queues.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Huazhong Tan says:

====================
net: hns3: add some misc update about reset issue

This series includes some misc update relating to reset issue.
[patch 1/7] & [patch 2/7] splits hclge_reset()/hclgevf_reset()
into two parts: preparing and rebuilding. Since the procedure
of FLR should be separated out from the reset task([patch 3/7 &
patch 3/7]), then the FLR's processing can reuse these codes.

pci_error_handlers.reset_prepare() is void type function, so
[patch 6/7] & [patch 7/7] factor some codes related to PF
function reset to make the preparing done before .reset_prepare()
return.

BTW, [patch 5/7] enlarges the waiting time of reset for matching
the hardware's.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

hclge_reset_prepare_down() is only used to inform VF that PF is
going to do function reset, then using hclge_func_reset_sync_vf()
in hclge_reset_prepare_wait() to query whether VF is ready before
asserting PF function reset. To make the code more readable,
this patch uses a new function hclge_function_reset_notify_vf()
to do this job.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When synchronizes with VFs fail before PF function reset,
PF driver should go on its function reset, otherwise it
can not run normally anymore. So, hclge_func_reset_sync_vf()
should not affect the processing of PF reset, this patch
modifies its return type to void.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the load of firmware is high, its reset task may takes
more time(which will be as long as 35 seconds). So this
patch modifies HCLGE_RESET_WAIT_CNT to match the firmware's.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the actual work of VF FLR is handled in the reset task,
which is asynchronous. So in some case, if the preparing and
rebuilding are not done, then the VF FLR will trigger some problems,
for example, makes hardware go into chaos.

So this patch separates the process of VF FLR from reset task, and
adds a semaphore to serialize this reset and others.

When FLR's preparing fails, if there has other higher level reset
pending or failing times less than the HCLGE_FLR_RETRY_CNT, this
preparing should be retried, otherwise it will get into a wrong state.

BTW, while the hardware reports misc interrupt during pcie_flr(),
the driver can not receive this interrupt anymore, so disable it
when hclgevf_flr_prepare() return, and re-enable it when enter
hclgevf_flr_done().

Avoid declaring internal function hclgevf_enable_vector(), this patch
also moves its definition forward, and removes unused enum
hnae3_flr_state.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the actual work of PF FLR is handled in the reset task,
which is asynchronous. So in some case, if the preparing and
rebuilding are not done, then the PF FLR will trigger some problems,
for example, makes hardware go into chaos.

So this patch separates the process of PF FLR from reset task, and
adds a semaphore to serialize this reset and others.

When FLR's preparing fails, if there has other higher level reset
pending or failing times less than the HCLGE_FLR_RETRY_CNT, this
preparing should be retried, otherwise PF and its VF may get into
wrong state.

BTW, while the hardware reports misc interrupt during pcie_flr(),
the driver can not receive this interrupt anymore, so disable it
when hclge_flr_prepare() return, and re-enable it when enter
hclge_flr_done().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hclgevf_reset() is a little bloated, and the process of VF FLR will
be separated from the reset task later. So this patch splits
hclgevf_reset() into hclgevf_reset_prepare() and hclge_reset_rebuild(),
then FLR can also reuse these two functions. Also moves HNAE3_UP_CLIENT
into hclgevf_reset_stack().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hclge_reset() is a little bloated, and the process of PF FLR will
be separated from the reset task later. So this patch splits
hclge_reset() into hclge_reset_prepare() and hclge_reset_rebuild(),
then FLR can also reuse these two functions.

BTW, since hclge_clear_reset_cause() and hclge_reset_prepare_up()
will not affect the device, so in hclge_reset_rebuild(), these
functions are called without rtnl_lock.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/sfc/mcdi_functions.c: In function 'efx_mcdi_ev_init':
drivers/net/ethernet/sfc/mcdi_functions.c:79:28: warning:
 variable 'nic_data' set but not used [-Wunused-but-set-variable]

commit 4438b587 ("sfc: move MCDI event queue management code")
introduces this unused variable.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running in XDP mode, pages come from the page pool, and should
be freed back to the same pool or specifically detached.  Currently,
when the driver re-initializes, the page pool destruction is delayed
forever since it thinks there are oustanding pages.

Fixes: 322b87ca ("bnxt_en: add page_pool support")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jacob Keller says:

====================
devlink documentation refactor

This series updates the devlink documentation, with a few primary goals

 * move all of the devlink documentation into a dedicated subfolder
 * convert that documentation to the reStructuredText format
 * merge driver-specific documentations into a single file per driver
 * add missing documentation, including per-driver and devlink generally

For each driver, I took the time to review the code and add further
documentation on the various features it currently supports. Additionally, I
added new documentation files for some of the features such as
devlink-dpipe, devlink-resource, and devlink-regions.

Note for the region snapshot triggering, I kept that as a separate patch as
that is based on work that has not yet been merged to net-next, and may
change.

I also improved the existing documentation for devlink-info and
devlink-param by adding a bit more of an introduction when converting it to
the rst format.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that devlink regions can be triggered via
DEVLINK_CMD_REGION_TRIGGER, document this in the devlink-region.rst
file.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Primarily based on the DPIPE netdev conference paper, introduce a new
file to document the dpipe interface.

This likely needs further improvement, but is at least a good overall
start.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Take the little bit of documentation for resources from various commit
messages and combine it into a new devlink-resource.rst file.

This could probably be expanded on even further by someone with more
knowledge of how the devlink resources work.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename the trap-specific netdevimsim.rst file, and expand it to include
documentation of all the devlink features currently implemented by the
netdevsim driver code.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IONIC device driver allocates a devlink and reports versions. Add
documentation for this driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Shannon Nelson <snelson@pensando.io>
Acked-by: Shannon Nelson <snelson@pensandi.io>
Signed-off-by: David S. Miller <davem@davemloft.net>