Conflicts:
	sound/soc/codecs/wm8940.c

Occasionally we may see an accessory reported before we have a stable
impedance for the accessory. If this happens then reread the status in
order to ensure that the handler can take the appropriate action for the
status change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The field is no longer initialised so this will crash if running on
wm8958.
Reported-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The field is no longer initialised so this will crash if running on
wm8958.
Reported-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The thermal shutdown support in wm_hubs devices is tied to the speaker
drivers (which are the only high power subsystems within the device).
Ensure minimal current usage when the thermal shutdown support is not
required by disabling the circuit when the speaker drivers are powered
down.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Disable the thermal shutdown circuits for headphone and speaker when the
relevant outputs are not enabled in order to save current in idle modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The WM9081 thermal shutdown is only effective when the speaker output is
enabled so disable it when that is not in use for a small current saving.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

There's no point in adding unlikely() annotations outside of hot paths
and on systems using these features the annotation will always be wrong
(as opposed to being something that only comes up once in a while) so
the annotation may even be harmful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Remove the -2.6 from the name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Having a separate list for amps is a little confusing now the official
driver model for them is the same as for other CODECs so let's sort them
into the CODEC list, but only do this for those that are actual CODEC
drivers so it's easier to remember which ones need updating.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

They aren't needed any more. If machines need them for other purposes then
further changes will be required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Force MICBIAS on as well as SYSCLK as the WM8962 accessory detection can't
function without both. No point in making machine drivers manually enable
it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Ensure everything is set up before we start detecting.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Since we have code to automatically manage the start and stop of the FLL
based on the SYSCLK widget if SYSCLK is already enabled and the FLL is
configured then we need to start it up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Since there is no current software control for these they would otherwise
be left enabled, consuming power.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The WM8962 has a separate software reset for the PLL registers. Ensure that
these are reset also on startup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Set `invert' bit for Capture Switch. Otherwise analogue is muted when
Capture Switch is ON.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Current implementation in wm8711_set_dai_fmt always clear BIT[3:2]
(the Input Audio Data Bit Length Select) of WM8711_IFACE(07h) register.
Input Audio Data Bit Length Select bits are set by wm8711_hw_params,
we should leave BIT[3:2] untouched in wm8711_set_dai_fmt.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The Input Audio Data Bit Length Select is controlled by BIT[3:2] of
WM8711_IFACE(07h) register.
Current code incorrectly masks BIT[1:0] which is for Audio Data Format Select.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

With this flag, each dai_link in machine driver can choose
to ignore pmdown_time during DAPM shut down sequence.

If the ignore_pmdown_time is set, the DAPM for corresponding DAI
will be executed immediately.
Signed-off-by: Ramesh Babu K V <ramesh.babu@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet:

Page0 / Register8: Audio Serial Data interface Control Register A
BIT 7: Bit Clock Directional Control
        0: Bit clock is an input (slave mode)
        1: Bit clock is an output (master mode)

BIT 6: Word Clock Directional Control
        0: Word clock is an input (slave mode)
        1: Word clock is an output (master mode)

Current code sets BIT_CLK_MASTER and WORD_CLK_MASTER bits for master mode,
but does not clear these bits for slave mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet:

Digital Audio Interface Format (07h) register:
BIT6:	Master/slave mode
	0: Slave
	1: Master

Current code sets TLV320AIC23_MS_MASTER bit for master mode,
but does not clear it for slave mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

According to the datasheet:
BCLK is controlled by BIT[4:2] of WM8940_CLOCK(06h) register.
Signed-off-by: Chris Paulson-Ellis <chris@edesix.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Reported-by: Chris Paulson-Ellis <chris@edesix.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org