- 20 Jan, 2017 18 commits
-
-
Stephen Boyd authored
When the RESET bit is set in the USBCMD register it resets quite a few of the wrapper's registers to their reset state. This includes the GENCONFIG and GENCONFIG2 registers. Currently this is done by the usb phy and ehci-msm drivers writing into the controller wrapper's MMIO address space. Let's consolidate the register writes into the wrapper driver instead so that we clearly split the wrapper from the phys. Acked-by:
Peter Chen <peter.chen@nxp.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by:
-
Stephen Boyd authored
We need to pick the correct phy at runtime based on how the SoC has been wired onto the board. If the secondary phy is used, take it out of reset and mux over to it by writing into the TCSR register. Make sure to do this on reset too, because this register is reset to the default value (primary phy) after the RESET bit is set in USBCMD. Acked-by:
-
Stephen Boyd authored
The msm chipidea controller uses two main clks, an AHB clk to read/write the MMIO registers and a core clk called the system clk that drives the controller itself. Add support for these clks as they're required in all designs. Also add support for an optional third clk that we need to turn on to reset the controller and wrapper logic and other "housekeeping" things. This clk was removed in later revisions of the hardware because the reset methodology no longer required clks to be enabled to propagate resets. Acked-by:
-
Stephen Boyd authored
The MSM_USB_BASE macro trick is not very clear, and we're using it for only one register write so let's just move to using hw_write_id_reg() and passing the ci pointer instead. That clearly shows what offset we're using and avoids needing to include the msm_hsusb_hw.h file when we're going to delete that file soon. Acked-by:
-
Stephen Boyd authored
The core framework already handles setting this parameter with a platform quirk. Add the appropriate flag so that we always set AHBBURST to 0. Technically DT should be doing this, but we always do it for msm chipidea devices so setting the flag in the driver works just as well. If the burst needs to be anything besides 0, we expect the 'ahb-burst-config' dts property to be present. Acked-by:
-
Stephen Boyd authored
We're not properly marking the glue layer/wrapper device as runtime active, so runtime PM believes that the hardware state is inactive when we call pm_runtime_enable() in this driver. This causes a problem when the glue layer has a power domain associated with it, because runtime PM will go and disable the power domain to match the 'inactive' state of the device. Let's mark the device as active so that runtime PM doesn't improperly power down this device when it's actually active. Acked-by:
-
Peter Chen authored
At some situations, the vbus may already be there before starting gadget. So we need to check vbus event after switching to gadget in order to handle missing vbus event. The typical use cases are plugging vbus cable before driver load or the vbus has already been there after stopping host but before starting gadget. Signed-off-by:
-
Stephen Boyd authored
The two extcon notifiers are almost the same except for the variable name for the cable structure and the id notifier inverts the cable->state logic. Make it the same and replace two functions with one to save some lines. This also makes it so that the id cable state is true when the id pin is pulled low, so we change the name of ->state to ->connected to properly reflect that we're interested in the cable being connected. Acked-by:
-
Stephen Boyd authored
Some phys for the chipidea controller are controlled via the ULPI viewport. Add support for the ULPI bus so that these sorts of phys can be probed and read/written automatically without having to duplicate the viewport logic in each phy driver. Acked-by:
-
Stephen Boyd authored
We don't call hw_device_reset() with the ci->lock held, so it doesn't seem like this lock here is protecting anything. Let's just remove it. This allows us to call sleeping functions like phy_init() from within the CI_HDRC_CONTROLLER_RESET_EVENT hook. Acked-by:
-
Stephen Boyd authored
The chipidea/udc.c file sends a CI_HDRC_CONTROLLER_RESET_EVENT to the wrapper drivers when it calls hw_device_reset(), but that function is not called from chipidea/host.c. And the udc.c file sends the CI_HDRC_CONTROLLER_STOPPED_EVENT but the host.c file doesn't do anything. The intent of the reset event is to allow the wrapper driver to do any wrapper specific things after the reset bit has been set in the usb command register. Therefore, add this event hook in the host role after we toggle that bit. Similarly, the intent of the stopped event is to allow the wrapper driver to do any wrapper specific things after the device is stopped. So when we stop the host role, send the stopped event. Acked-by:
-
Stephen Boyd authored
The ULPI phy on qcom platforms needs to be initialized and powered on after a USB reset and before we toggle the run/stop bit. Otherwise, the phy locks up and doesn't work properly. Therefore, add a flag to skip any phy power management in the core layer, leaving it up to the glue driver to manage. Acked-by:
-
Stephen Boyd authored
We're currently emulating the vbus and id interrupts in the OTGSC read API, but we also need to make sure that if we're handling the events with extcon that we don't enable the interrupts for those events in the hardware. Therefore, properly emulate this register if we're using extcon, but don't enable the interrupts. This allows me to get my cable connect/disconnect working properly without getting spurious interrupts on my device that uses an extcon for these two events. Acked-by:
-
Stephen Boyd authored
With the id and vbus detection done via extcon we need to make sure we poll the status of OTGSC properly by considering what the extcon is saying, and not just what the register is saying. Let's move this hw_wait_reg() function to the only place it's used and simplify it for polling the OTGSC register. Then we can make certain we only use the hw_read_otgsc() API to read OTGSC, which will make sure we properly handle extcon events. Acked-by:
-
Stephen Boyd authored
The qcom HSIC ULPI phy doesn't have any bits set in the vendor or product ID registers. This makes it impossible to make a ULPI driver match against the ID registers. Add support to discover the ULPI phys via DT help alleviate this problem. In the DT case, we'll look for a ULPI bus node underneath the device registering the ULPI viewport (or the parent of that device to support chipidea's device layout) and then match up the phy node underneath that with the ULPI device that's created. The side benefit of this is that we can use standard properties in the phy node like clks, regulators, gpios, etc. because we don't have firmware like ACPI to turn these things on for us. And we can use the DT phy binding to point our phy consumer to the phy provider. The ULPI bus code supports native enumeration by reading the vendor ID and product ID registers at device creation time, but we can't be certain that those register reads will succeed if the phy is not powered up. To avoid any problems with reading the ID registers before the phy is powered we fallback to DT matching when the ID reads fail. If the ULPI spec had some generic power sequencing for these registers we could put that into the ULPI bus layer and power up the device before reading the ID registers. Unfortunately this doesn't exist and the power sequence is usually device specific. By having the device matched up with DT we can avoid this problem. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: <devicetree@vger.kernel.org> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Stephen Boyd authored
The ULPI bus can be built as a module, and it will soon be calling these functions when it supports probing devices from DT. Export them so they can be used by the ULPI module. Acked-by:
-
Stephen Boyd authored
In the case of ULPI devices, we want to be able to load the driver before registering the device so that we don't get stuck in a loop waiting for the phy module to appear and failing usb controller probe. Currently we request the ulpi module via the ulpi ids, but in the DT case we might need to request it with the OF based modalias instead. Add a common function that allows anyone to request a module with the OF based modalias. Acked-by:
-
Chanwoo Choi authored
This patch uses the resource-managed extcon API for extcon_register_notifier() and replaces the deprecated extcon API as following: - extcon_get_cable_state_() -> extcon_get_state() Signed-off-by:
Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by:
-
- 26 Dec, 2016 2 commits
-
-
Linus Torvalds authored
-
Larry Finger authored
I am getting the following warning when I build kernel 4.9-git on my PowerBook G4 with a 32-bit PPC processor: AS arch/powerpc/kernel/misc_32.o arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef] This problem is evident after commit 989cea5c ("kbuild: prevent lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an error that has been in the code since 2005 when this source file was created. That was with commit 9994a338 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S"). The offending line does not make a lot of sense. This error does not seem to cause any errors in the executable, thus I am not recommending that it be applied to any stable versions. Thanks to Nicholas Piggin for suggesting this solution. Fixes: 9994a338 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S") Signed-off-by:Larry Finger <Larry.Finger@lwfinger.net> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
- 25 Dec, 2016 20 commits
-
-
Linus Torvalds authored
The timer type simplifications caused a new gcc warning: drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’: drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized] elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start)); despite the actual use of "time_start" not having changed in any way. It appears that simply changing the type of ktime_t from a union to a plain scalar type made gcc check the use. The variable wasn't actually used uninitialized, but gcc apparently failed to notice that the conditional around the use was exactly the same as the conditional around the initialization of that variable. Add an unnecessary initialization just to shut up the compiler. Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer type cleanups from Thomas Gleixner: "This series does a tree wide cleanup of types related to timers/timekeeping. - Get rid of cycles_t and use a plain u64. The type is not really helpful and caused more confusion than clarity - Get rid of the ktime union. The union has become useless as we use the scalar nanoseconds storage unconditionally now. The 32bit timespec alike storage got removed due to the Y2038 limitations some time ago. That leaves the odd union access around for no reason. Clean it up. Both changes have been done with coccinelle and a small amount of manual mopping up" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: ktime: Get rid of ktime_equal() ktime: Cleanup ktime_set() usage ktime: Get rid of the union clocksource: Use a plain u64 instead of cycle_t -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull SMP hotplug notifier removal from Thomas Gleixner: "This is the final cleanup of the hotplug notifier infrastructure. The series has been reintgrated in the last two days because there came a new driver using the old infrastructure via the SCSI tree. Summary: - convert the last leftover drivers utilizing notifiers - fixup for a completely broken hotplug user - prevent setup of already used states - removal of the notifiers - treewide cleanup of hotplug state names - consolidation of state space There is a sphinx based documentation pending, but that needs review from the documentation folks" * 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqchip/armada-xp: Consolidate hotplug state space irqchip/gic: Consolidate hotplug state space coresight/etm3/4x: Consolidate hotplug state space cpu/hotplug: Cleanup state names cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions staging/lustre/libcfs: Convert to hotplug state machine scsi/bnx2i: Convert to hotplug state machine scsi/bnx2fc: Convert to hotplug state machine cpu/hotplug: Prevent overwriting of callbacks x86/msr: Remove bogus cleanup from the error path bus: arm-ccn: Prevent hotplug callback leak perf/x86/intel/cstate: Prevent hotplug callback leak ARM/imx/mmcd: Fix broken cpu hotplug handling scsi: qedi: Convert to hotplug state machine
-
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linuxLinus Torvalds authored
Pull turbostat updates from Len Brown. * 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: tools/power turbostat: remove obsolete -M, -m, -C, -c options tools/power turbostat: Make extensible via the --add parameter tools/power turbostat: Denverton uses a 25 MHz crystal, not 19.2 MHz tools/power turbostat: line up headers when -M is used tools/power turbostat: fix SKX PKG_CSTATE_LIMIT decoding tools/power turbostat: Support Knights Mill (KNM) tools/power turbostat: Display HWP OOB status tools/power turbostat: fix Denverton BCLK tools/power turbostat: use intel-family.h model strings tools/power/turbostat: Add Denverton RAPL support tools/power/turbostat: Add Denverton support tools/power/turbostat: split core MSR support into status + limit tools/power turbostat: fix error case overflow read of slm_freq_table[] tools/power turbostat: Allocate correct amount of fd and irq entries tools/power turbostat: switch to tab delimited output tools/power turbostat: Gracefully handle ACPI S3 tools/power turbostat: tidy up output on Joule counter overflow
-
Nicholas Piggin authored
Add a new page flag, PageWaiters, to indicate the page waitqueue has tasks waiting. This can be tested rather than testing waitqueue_active which requires another cacheline load. This bit is always set when the page has tasks on page_waitqueue(page), and is set and cleared under the waitqueue lock. It may be set when there are no tasks on the waitqueue, which will cause a harmless extra wakeup check that will clears the bit. The generic bit-waitqueue infrastructure is no longer used for pages. Instead, waitqueues are used directly with a custom key type. The generic code was not flexible enough to have PageWaiters manipulation under the waitqueue lock (which simplifies concurrency). This improves the performance of page lock intensive microbenchmarks by 2-3%. Putting two bits in the same word opens the opportunity to remove the memory barrier between clearing the lock bit and testing the waiters bit, after some work on the arch primitives (e.g., ensuring memory operand widths match and cover both bits). Signed-off-by:
Nicholas Piggin <npiggin@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Bob Peterson <rpeterso@redhat.com> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Andrew Lutomirski <luto@kernel.org> Cc: Andreas Gruenbacher <agruenba@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by:
-
Nicholas Piggin authored
A page is not added to the swap cache without being swap backed, so PageSwapBacked mappings can use PG_owner_priv_1 for PageSwapCache. Signed-off-by:
Hugh Dickins <hughd@google.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Bob Peterson <rpeterso@redhat.com> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Andrew Lutomirski <luto@kernel.org> Cc: Andreas Gruenbacher <agruenba@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by:
-
Thomas Gleixner authored
No point in going through loops and hoops instead of just comparing the values. Signed-off-by:Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org>
-
Thomas Gleixner authored
ktime_set(S,N) was required for the timespec storage type and is still useful for situations where a Seconds and Nanoseconds part of a time value needs to be converted. For anything where the Seconds argument is 0, this is pointless and can be replaced with a simple assignment. Signed-off-by: -
Thomas Gleixner authored
ktime is a union because the initial implementation stored the time in scalar nanoseconds on 64 bit machine and in a endianess optimized timespec variant for 32bit machines. The Y2038 cleanup removed the timespec variant and switched everything to scalar nanoseconds. The union remained, but become completely pointless. Get rid of the union and just keep ktime_t as simple typedef of type s64. The conversion was done with coccinelle and some manual mopping up. Signed-off-by: -
Thomas Gleixner authored
There is no point in having an extra type for extra confusion. u64 is unambiguous. Conversion was done with the following coccinelle script: @rem@ @@ -typedef u64 cycle_t; @fix@ typedef cycle_t; @@ -cycle_t +u64 Signed-off-by: -
Thomas Gleixner authored
The mpic is either the main interrupt controller or is cascaded behind a GIC. The mpic is single instance and the modes are mutually exclusive, so there is no reason to have seperate cpu hotplug states. Signed-off-by:
-
Thomas Gleixner authored
Even if both drivers are compiled in only one instance can run on a given system depending on the available GIC version. So having seperate hotplug states for them is pointless. Signed-off-by:
-
Thomas Gleixner authored
Even if both drivers are compiled in only one instance can run on a given system depending on the available tracer cell. So having seperate hotplug states for them is pointless. Signed-off-by:
-
Thomas Gleixner authored
When the state names got added a script was used to add the extra argument to the calls. The script basically converted the state constant to a string, but the cleanup to convert these strings into meaningful ones did not happen. Replace all the useless strings with 'subsys/xxx/yyy:state' strings which are used in all the other places already. Signed-off-by:
-
Thomas Gleixner authored
hotcpu_notifier(), cpu_notifier(), __hotcpu_notifier(), __cpu_notifier(), register_hotcpu_notifier(), register_cpu_notifier(), __register_hotcpu_notifier(), __register_cpu_notifier(), unregister_hotcpu_notifier(), unregister_cpu_notifier(), __unregister_hotcpu_notifier(), __unregister_cpu_notifier() are unused now. Remove them and all related code. Remove also the now pointless cpu notifier error injection mechanism. The states can be executed step by step and error rollback is the same as cpu down, so any state transition can be tested w/o requiring the notifier error injection. Some CPU hotplug states are kept as they are (ab)used for hotplug state tracking. Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
Anna-Maria Gleixner authored
Install the callbacks via the state machine. No functional change. Signed-off-by:
Anna-Maria Gleixner <anna-maria@linutronix.de> Signed-off-by:
-
Sebastian Andrzej Siewior authored
Install the callbacks via the state machine. No functional change. This is the minimal fixup so we can remove the hotplug notifier mess completely. The real rework of this driver to use work queues is still stuck in review/testing on the SCSI mailing list. Signed-off-by:
-
Sebastian Andrzej Siewior authored
Install the callbacks via the state machine. No functional change. This is the minimal fixup so we can remove the hotplug notifier mess completely. The real rework of this driver to use work queues is still stuck in review/testing on the SCSI mailing list. Signed-off-by:
-
Thomas Gleixner authored
Developers manage to overwrite states blindly without thought. That's fatal and hard to debug. Add sanity checks to make it fail. This requries to restructure the code so that the dynamic state allocation happens in the same lock protected section as the actual store. Otherwise the previous assignment of 'Reserved' to the name field would trigger the overwrite check. Signed-off-by:
-
Thomas Gleixner authored
The error cleanup which is invoked when the hotplug state setup failed tries to remove the failed state, which is broken. Fixes: 8fba38c9 ("x86/msr: Convert to hotplug state machine") Reported-by:
kernel test robot <fengguang.wu@intel.com> Signed-off-by:
-
